In situ growth of iron incorporated Ni3S2 nanosheet on nickel foam in mediating electron transfer to peroxymonosulfate for pollutant abatement.

Catalytic oxidation of organic pollutants is a well-known and effective technique for pollutant abatement. Unfortunately, this method is significantly hindered in practical applications by the low efficiency and difficult recovery of the catalysts in a powdery form. Herein, a three-dimensional (3D) framework of Fe-incorporated Ni3S2 nanosheets in-situ grown on Ni foam (Fe-Ni3S2@NF) was fabricated by a facile two-step hydrothermal process and applied to trigger peroxymonosulfate (PMS) oxidation of organic compounds in water. A homogeneous growth environment enabled the uniform and scalable growth of Fe-Ni3S2 nanosheets on the Ni foam. Fe-Ni3S2@NF possessed outstanding activity and durability in activating PMS, as it effectively facilitated electron transfer from organic pollutants to PMS. Fe-Ni3S2@NF initially supplied electrons to PMS, causing the catalyst to undergo oxidation, and subsequently accepted electrons from organic compounds, returning to its initial state. The introduction of Fe into the Ni3S2 lattice enhanced electrical conductivity, promoting mediated electron transfer between PMS and organic compounds. The 3D conductive Ni foam provided an ideal platform for the nucleation and growth of Fe-Ni3S2, accelerating pollutant abatement due to its porous structure and high conductivity. Furthermore, its monolithic nature simplified the catalyst recycling process. A continuous flow packed-bed reactor by encapsulating Fe-Ni3S2@NF catalyst achieved complete pollutant abatement with continuous operation for 240 h, highlighting its immense potential for practical environmental remediation. This study presents a facile synthesis method for creating a novel type of monolithic catalyst with high activity and durability for decontamination through Fenton-like processes.

Co-doped cryptomelane-type manganese oxide in situ grown on a nickel foam substrate for high humidity ozone decomposition.

Monolithic catalysts with excellent O3 catalytic decomposition performance were prepared by in situ loading of Co-doped KMn8O16 on the surface of nickel foam. The triple-layer structure with Co-doped KMn8O16/Ni6MnO8/Ni foam was grown spontaneously on the surface of nickel foam by tuning the molar ratio of KMnO4 to Co(NO3)2·6H2O precursors. Importantly, the formed Ni6MnO8 structure between KMn8O16 and nickel foam during in situ synthesis process effectively protected nickel foam from further etching, which significantly enhanced the reaction stability of catalyst. The optimum amount of Co doping in KMn8O16 was available when the molar ratio of Mn to Co species in the precursor solution was 2:1. And the Mn2Co1 catalyst had abundant oxygen vacancies and excellent hydrophobicity, thus creating outstanding O3 decomposition activity. The O3 conversion under dry conditions and relative humidity of 65%, 90% over a period of 5 hr was 100%, 94% and 80% with the space velocity of 28,000 hr-1, respectively. The in situ constructed Co-doped KMn8O16/Ni foam catalyst showed the advantages of low price and gradual applicability of the preparation process, which provided an opportunity for the design of monolithic catalyst for O3 catalytic decomposition.

Square-wave pulsed potential driven electrocatalytic degradation of 4-chlorophenol using Fe-Ni/rGO/PPy@NF three dimensional electrode.

To develop an energy-efficient system for the removal of chlorinated organic pollutants, Fe-Ni/reduced graphite oxide/polymerized polypyrrole@nickel foam was constructed as a catalytic cathode for pulsed electrocatalytic degradation, where cathode-catalyzed production of hydrogen radicals (H*) and hydroxyl radical (·OH) generated at the anode led to dechlorination of 4-chlorophenol (4-CP), and dechlorination products were mineralized and degraded under the action of·OH. When energy was continuously supplied to the reaction system in the constant potential mode, the 4-CP concentration near the electrode was insufficient, limiting the reaction rate. Conversely, in the square-wave pulsed potential mode, mass transfer limitations were mitigated, significantly enhancing reaction efficiency and reducing energy consumption. At -1.2 V (vs. Ag/AgCl), the 4-CP removal efficiency reached 93.79 % in the pulsed potential mode, surpassing the constant potential mode's performance of 81.40 %. The synergistic periodic oscillation of the potential, direct electron transfer, and catalytic generation of active free radicals in the pulsed potential mode reduced intermediate concentrations and increased 4-CP mineralization, while the degradation pathway remained unchanged. This research presents a method for the efficient treatment of chlorinated organic pollutants in water using pulsed electrocatalytic degradation.

Nitrogen-Tungsten Oxide Nanostructures on Nickel Foam as High Efficient Electrocatalysts for Benzyl Alcohol Oxidation.

Electrocatalytic alcohol oxidation (EAO) is an attractive alternative to the sluggish oxygen evolution reaction in electrochemical hydrogen evolution cells. However, the development of high-performance bifunctional electrocatalysts is a major challenge. Herein, we developed a nitrogen-doped bimetallic oxide electrocatalyst (WO-N/NF) by a one-step hydrothermal method for the selective electrooxidation of benzyl alcohol to benzoic acid in alkaline electrolytes. The WO-N/NF electrode features block-shaped particles on a rough, inhomogeneous surface with cracks and lumpy nodules, increasing active sites and enhancing electrolyte diffusion. The electrode demonstrates exceptional activity, stability, and selectivity, achieving efficient benzoic acid production while reducing the electrolysis voltage. A low onset potential of 1.38 V (vs. RHE) is achieved to reach a current density of 100 mA cm-2 in 1.0 M KOH electrolyte with only 0.2 mmol of metal precursors, which is 396 mV lower than that of water oxidation. The analysis reveals a yield, conversion, and selectivity of 98.41%, 99.66%, and 99.74%, respectively, with a Faradaic efficiency of 98.77%. This work provides insight into the rational design of a highly active and selective catalyst for electrocatalytic alcohol oxidation.

Three-Dimensional Nickel Foam-Based Lithiophilic LPP-Ni3S2@Ni Current Collector for Dendrite-Free Lithium Anode.

Lithium metal has been treated as one of the most promising anode materials for next-generation rechargeable batteries due to its extremely high theoretical capacity. However, its practical application is hindered by inhomogeneous lithium deposition and uncontrolled dendrite growth. In this work, we prepared a three-dimensional nickel foam (NF)-based current collector with a lithiophilic interface layer through facile hydrothermal and coating methods. The lithiophilic Ni3S2 array synthesized via a hydrothermal method has been demonstrated to facilitate the nucleation of Li+. Moreover, it has been observed that the outer coating comprising LPP effectively enhances the inward diffusion of Li+. Additionally, this interface layer can serve as an isolating barrier between the electrodes and the electrolyte. The prepared LPP-Ni3S2@Ni shows significant reversibility both in symmetric cells (1200 h, 1 mA cm-2) and half-cells (CE: 99.60%, 500 cycles, 1 mA cm-2) with low interfacial resistance (35 Ω). Full cells with LiFePO4 as a cathode also exhibit promising electrochemical performance with over 76.78% capacity retention over 200 cycles at 1 C.

Peroxymonosulfate activation by iron-cobalt bimetallic phosphide modified nickel foam for efficient dye degradation.

Novel catalysts with multiple active sites and rapid separation are required to effectively activate peroxymonosulfate (PMS) for the removal of organic pollutants from water. Therefore, an integrated catalyst for PMS activation was developed by directly forming Co-Fe Prussian blue analogs on a three-dimensional porous nickel foam (NF), which were subsequently phosphorylated to obtain cobalt-iron bimetallic phosphide (FeCoP@NF). The FeCoP@NF/PMS system efficiently degraded dye wastewater within 20 min. The system exhibited excellent catalytic degradation over a broad pH range and at high dye concentrations due to the presence of unique asymmetrically charged Coa+ and Pb- dual active sites formed by cobalt phosphides within FeCoP@NF. These active sites significantly enhanced the catalytic activity of PMS. The activation mechanism of PMS involves phosphorylation that accelerates electron transfer from FeCoP@NF to PMS, to generate SO4·-, ·OH, O2·-, and 1O2 active species. Three-dimensional FeCoP@NF could be readily recycled and showed good stability for PMS activation. In this study, a highly efficient, stable, and readily recyclable integrated catalyst was developed. This catalyst system effectively resolves the separation and recovery issues associated with conventional powder catalysts and has a wide range of potential applications in wastewater treatment.

Gas-Phase-Induced Engineering for Fabrication of 3D Hierarchical Porous Nickel and Its Application toward High-Performance Supercapacitors.

Commercial nickel foam (NF), which is composed of numerous interconnected ligaments and hundred-micron pores, is widely acknowledged as a current collector/electrode material for catalysis, sensing, and energy storage applications. However, the commonly used NF often does not work satisfactorily due to its smooth surface and hollow structure of the ligaments. Herein, a gas-phase-induced engineering, two-step gaseous oxidation-reduction (GOR) is presented to directly transform the thin-walled hollow ligament of NF into a three-dimensional (3D) nanoporous prism structure, resulting in the fabrication of a unique hierarchical porous nickel foam (HPNF). This 3D nanoporous architecture is achieved by utilizing the spontaneous reconstruction of nickel atoms during volume expansion and contraction in the GOR process. The process avoids the involution of acid-base corrosion and sacrificial components, which are facile, environmentally friendly, and suitable for large-scale fabrication. Furthermore, MnO2 is electrochemically deposited on the HPNF to form a supercapacitor electrode (HPNF/MnO2). Because of the fully open structure for ion transport, superhydrophilic properties, and the increased contact area between MnO2 and the current collector, the HPNF/MnO2 electrode exhibits a high specific capacitance of 997.5 F g-1 at 3 A g-1 and remarkable cycling stability with 99.6% capacitance retention after 20000 cycles in 0.1 M Na2SO4 electrolyte, outperforming most MnO2-based supercapacitor electrodes.

In-situ growth of Mn-Ni3S2 on nickel foam for catalytic ozonation of p-nitrophenol.

In this study, a new catalyst for catalytic ozonation was obtained by in-situ growth of Mn-Ni3S2 nanosheets on the surface of nickel foam (NF). The full degradation of p-nitrophenol (PNP) was accomplished under optimal conditions in 40 min. The effects of material dosage, ozone dosage, pH and the presence of inorganic anions on the degradation efficiency of PNP were investigated. ESR analysis showed that singlet oxygen (1O2) and superoxide radical (O2•-) are the main contributors of PNP degradation. This study offers a new combination of supported catalysts with high efficiency and easy recovery, which provides a new idea for wastewater treatment.

Rational Design of Nanosheet Array-Like Layered-Double-Hydroxide-Derived NiCo2O4 In Situ Grown on Reduced-Graphene-Oxide-Coated Nickel Foam for High-Performance Solid-State Supercapacitors.

The investigation of high-performance supercapacitors is essential for accelerating the development of energy storage devices. In this work, a 3D hierarchical nanosheet array-like nickel cobaltite/reduced graphene oxide/nickel foam composite (NiCo2O4/rGO/NF) was assembled via an aqueous coprecipitation-hydrothermal strategy assisted by citric acid. Benefiting from a NiCo layered-double-hydroxide precursor with an atomic-level lattice confinement effect of metal ions and effective hybridization with rGO, the NiCo2O4/rGO/NF composite is featured as thin NiCo2O4 nanosheets (∼113.6 nm × 11.2 nm) composed of NiCo2O4 nanoparticles (∼10.9 nm) vertically staggered on the surface of a rGO-modified NF skeleton, leading to high surface area, abundant mesoporous structure, and active site exposure. The as-obtained NiCo2O4/rGO/NF was directly used as a binder-free integrated electrode for supercapacitors, achieving an excellent specific capacitance of 2863.4 F g-1 (1503.3 C g-1) at 1 A g-1, a superior rate performance of 2335.2 F g-1 at 20 A g-1, and a stability retention of 91.7% after 5000 cycles. More impressively, a solid-state asymmetric supercapacitor assembled by the present NiCo2O4/rGO/NF integrated electrode as the positive electrode and commercial activated carbon as the negative electrode achieved a high energy density of 69.2 Wh kg-1 at a power density of 800 W kg-1, and the energy density at a peak power density of 20004 W kg-1 still remained at 48.9 Wh kg-1, also showing a good cycling stability of 87.2% retention over 10000 cycles. The present facile synthesis strategy of the as-obtained NiCo2O4/rGO/NF nanosheet array composite can be used for the design and construction of many other transition-metal oxide/graphene/NF composite materials with excellent structural stability and performance in energy storage and other related areas.

Application of TiO2 Supported on Nickel Foam for Limitation of NOx in the Air via Photocatalytic Processes.

TiO2 was loaded on the porous nickel foam from the suspended ethanol solution and used for the photocatalytic removal of NOx. Such prepared material was heat-treated at various temperatures (400-600 °C) to increase the adhesion of TiO2 with the support. Obtained TiO2/nickel foam samples were characterized by XRD, UV-Vis/DR, FTIR, XPS, AFM, SEM, and nitrogen adsorption at 77 K. Photocatalytic tests of NO abatement were performed in the rectangular shape quartz reactor, irradiated from the top by UV LED light with an intensity of 10 W/m2. For these studies, a laminar flow of NO in the air (1 ppm) was applied under a relative humidity of 50% and a temperature of 28 °C. Concentrations of both NO and NO2 were monitored by a chemiluminescence NO analyzer. The adsorption of nitrogen species on the TiO2 surface was determined by FTIR spectroscopy. Performed studies revealed that increased temperature of heat treatment improves adhesion of TiO2 to the nickel foam substrate, decreases surface porosity, and causes removal of hydroxyl and alcohol groups from the titania surface. The less hydroxylated surface of TiO2 is more vulnerable to the adsorption of NO2 species, whereas the presence of OH groups on TiO2 enhances the adsorption of nitrate ions. Adsorbed nitrate species upon UV irradiation and moisture undergo photolysis to NO2. As a consequence, NO2 is released into the atmosphere, and the efficiency of NOx removal is decreasing. Photocatalytic conversion of NO to NO2 was higher for the sample heated at 400 °C than for that at 600 °C, although coverage of nickel foam by TiO2 was lower for the former one. It is stated that the presence of titania defects (Ti3+) at low temperatures of its heating enhances the adsorption of hydroxyl groups and the formation of hydroxyl radicals, which take part in NO oxidation. Contrary to that, the presence of titania defects in TiO2 through the formation of ilmenite structure (NiTiO3) in TiO2/nickel foam heated at 600 °C inhibits its photocatalytic activity. No less, the sample obtained at 600 °C indicated the highest abatement of NOx due to the high and stable adsorption of NO2 species on its surface.

A facile paper-based chromatography coupled Au nanodendrite on nickel foam for application in separation and SERS measurement.

A simple paper-based chromatography coupling with nickel foam decorated Au nanodendrite (PP-AuND/NiF) was fabricated for simultaneous separation and surface-enhanced Raman scattering (SERS) detection of Rhodamine-6G (R6G) from a mixture of analytes. The three-dimensional porous nickel foam (NiF) was employed as a sampling diffusion platform, and AuND with a high surface active area beneficial for SERS efficiency was electro-deposited directly onto the NiF frame. The structure of AuND/NiF was characterized by X-ray diffraction and scanning electron microscopy. The AuND/NiF could detect R6G at 0.1 nM, and the enhancement factor was 1.84 x 106. The AuND/NiF was durable, with a slight signal decrease after 6 m of drop-testing. Also, upon three days of exposure to ambient air, the signal droped only 3.35 %. Subsequently, the PP-AuND/NiF was constructed by directly situating AuND/NiF on a paper strip, serving as a sample in and out to AuND/NiF. A mixture of two SERS active compounds, namely 2-Naphthalenethiol (2-NpSH) and Rhodamine 6G (R6G), was prepared in ethanol: water (1:1) solution to evaluate PP-AuND/NiF separation capability. Raman measurements along different distances of AuND/NiF were performed, and the signal of 2-NpSH was dismissed after 3.0 mm, while R6G's signals were observed throughout AuND/NiF. In general, the PP-AuND/NiF demonstrated effective separation and SERS measurement of analytes in a mixture, which could be applicable for more complex samples in the future, especially in clinical analysis.

Electrocatalytic reduction of nitrate to ammonia by Pd/In modified Nickel foam electrode in aqueous solution.

Nitrate pollution in surface water and ground water has drawn wide attention, which has brought challenges to human health and natural ecology. Electroreduction of nitrate to NH3 in waste water was a way to turn waste into wealth, which has attracted interest of many researchers. Using Nickel foam as substrate, we prepared Pd/In bimetallic electrode (NF-Pd/In) according to a two-step electrodeposition method. There are many irregularly shaped particles in the size range of 10 nm-100 nm accumulated on the surface of prepared NF-Pd/In electrode, which could supply high specific area and more active sites for nitrate electroreduction. FESEM-EDS, XRD and XPS analysis confirmed the uniform distribution of Pd and In on the surface of prepared NF-Pd/In electrode, with a mass ratio of 4.5/1. Above 96% of 100 mg/L NO3--N was removed and 95% of NH3 selectivity was reached after 5 h of reaction under -1.6 V vs. Ag/AgCl sat. KCl when using 0.05 mol/L of Na2SO4 as electrolyte. High concentration of NaCl (0.05 mol/L) in the test solution dramatically decreased the NH3 selectivity because the produced NH3 could be further oxidized to N2 by the formed HClO from Cl-. EIS tests indicated that the prepared NF-Pd/In electrode showed much lower electrode resistance than NF due to the adsorptive property and electrocatalytic ability for nitrate removal. Density functional theory (DFT) calculations indicated that the presence of In could promote the conversion of NO3- to *NO3 during the process of nitrate electroreduction to NH3. Circulating tests demonstrated the stability of prepared NF-Pd/In electrode.

Bismuth sulfide micro flowers decorated nickel foam as a promising electrochemical sensor for quantitative analysis of melamine in bottled milk samples.

Here, we demonstrate hydrothermally grown bismuth sulfide (Bi2S3) micro flowers decorated nickel foam (NF) for electrochemical detection of melamine in bottled milk samples. The orthorhombic phase of hydrothermally grown Bi2S3is confirmed by the detailed characterization of x-ray diffraction and its high surface area micro flowers-like morphology is investigated via field emission scanning electron microscope. Furthermore, the surface chemical oxidation state and binding energy of Bi2S3/NF micro flowers is analyzed by x-ray photoelectron spectroscopy studies. The sensor exhibits a wide linear range of detection from 10 ng l-1to 1 mg l-1and a superior sensitivity of 3.4 mA cm-2to melamine using differential pulse voltammetry technique, with a lower limit of detection (7.1 ng l-1). The as-fabricated sensor is highly selective against interfering species of p-phenylenediamine (PPDA), cyanuric acid (CA), aniline, ascorbic acid, glucose (Glu), and calcium ion (Ca2+). Real-time analysis done in milk by the standard addition method shows an excellent recovery percentage of Ì´ 98%. The sensor's electrochemical mechanism studies reveal that the high surface area bismuth sulfide micro flowers surface interacts strongly with melamine molecules through hydrogen bonding and van der Waals forces, resulting in a significant change in the sensor's electrical properties while 3D skeletal Nickel foam as a substrate provides stability, enhances its catalytic activity by providing a more number /of active sites and facilitates rapid electron transfer. The work presented here confirms Bi2S3/NF as a high-performance electrode that can be used for the detection of other biomolecules used in clinical diagnosis and biomedical research.

Enhanced Degradation of Ethylene in Thermo-Photocatalytic Process Using TiO2/Nickel Foam.

The photocatalytic decomposition of ethylene was performed under UV-LED irradiation in the presence of nanocrystalline TiO2 (anatase, 15 nm) supported on porous nickel foam. The process was conducted in a high-temperature chamber with regulated temperature from ambient to 125 °C, under a flow of reacted gas (ethylene in synthetic air, 50 ppm, flow rate of 20 mL/min), with simultaneous FTIR measurements of the sample surface. Ethylene was decomposed with a higher efficiency at elevated temperatures, with a maximum of 28% at 100-125 °C. The nickel foam used as support for TiO2 enhanced ethylene decomposition at a temperature of 50 °C. However, at 50 °C, the stability of ethylene decomposition was not maintained in the following reaction run, but it was at 100 °C. Photocatalytic measurements conducted in the presence of certain radical scavengers indicated that a higher efficiency of ethylene decomposition was obtained due to the improved separation of charge carriers and the increased formation of superoxide anionic radicals, which were formed at the interface of the thermally activated nickel foam and TiO2.

Synergistic integration of Ni-metal organic framework/SnS2nanocomposite and nickel foam electrode for ultrasensitive and selective electrochemical detection of albumin in simulated human blood serum.

Albumin is a vital blood protein responsible for transporting metabolites and drugs throughout the body and serves as a potential biomarker for various medical conditions, including inflammatory, cardiovascular, and renal issues. This report details the fabrication of Ni-metal organic framework/SnS2nanocomposite modified nickel foam electrochemical sensor for highly sensitive and selective non enzymatic detection of albumin in simulated human blood serum samples. Ni-metal organic framework/SnS2nanocomposite was synthesized using solvothermal technique by combining Ni-metal-organic framework (MOF) with conductive SnS2leading to the formation of a highly porous material with reduced toxicity and excellent electrical conductivity. Detailed surface morphology and chemical bonding of the Ni-MOF/SnS2nanocomposite was studied using scanning electron microscopy, transmission electron microscopy, Fourier transform infra-red, and Raman analysis. The Ni-MOF/SnS2nanocomposite coated on Ni foam electrode demonstrated outstanding electrochemical performance, with a low limit of detection (0.44µM) and high sensitivity (1.3µA/pM/cm2) throughout a broad linear range (100 pM-10 mM). The remarkable sensor performance is achieved through the synthesis of a Ni-MOF/SnS2nanocomposite, enhancing electrocatalytic activity for efficient albumin redox reactions. The enhanced performance can be attributed due to the structural porosity of nickel foam and Ni-metal organic framework, which favours increased surface area for albumin interaction. The presence of SnS2shows stability in acidic and neutral solutions due to high surface to volume ratio which in turn improves sensitivity of the sensing material. The sensor exhibited commendable selectivity, maintaining its performance even when exposed to potential interfering substances like glucose, ascorbic acid, K+, Na+, uric acid, and urea. The sensor effectively demonstrates its accuracy in detecting albumin in real samples, showcasing substantial recovery percentages of 105.1%, 110.28%, and 91.16%.

Interface regulation of Zr-MOF/Ni2P@nickel foam as high-efficient electrocatalyst for pH-universal hydrogen evolution reaction.

Currently, the development of economical and effective non-noble metal electrocatalysts is vital for advancing hydrogen evolution reaction (HER) and enabling its widespread applications. The customizable pore structure and enormous surface area of metal-organic frameworks (MOFs) have made them to become promising non-noble metal electrocatalysts for HER. However, MOFs have some challenges, including low conductivity and instability, which can result in them having high overpotentials and slow reaction kinetics in electrocatalytic processes. In this work, we present an innovative approach for synthesizing cost-effective and high-efficient Zr-MOF-derived pH-universal electrocatalysts for HER. It entails creating the interfaces of the electrocatalysts with suitable proportions of phosphide nanostructures. Zr-MOF/Ni2P@nickel foam (NF) electrodes with interface regulated by Ni2P nanostructures were successfully developed for high-efficient pH-universal HER electrocatalysts. The presence of Ni2P nanostructures with abundant active sites at the Zr-MOFs@NF interfaces boosted the electronic conductivity and local charge density of the hybrid electrocatalysts. This helped to improve their reaction kinetics and electrocatalytic activity. By optimizing the Ni2P amount, Zr-MOF/Ni2P@NF demonstrated impressive stability and superior HER activities, with a low overpotential of 149 mV (acidic electrolytes) and 143 mV (alkaline electrolytes) at 10 mA cm-2. The proven strategy in this work can be expanded to many types of MOF-based materials for wider practical applications.

Amorphous Co-Mo-P film on nickel foam: a superior bifunctional electrocatalyst for alkaline seawater splitting.

Seawater splitting is a compelling avenue to produce abundant hydrogen, which requires high-performance and cost-effective catalysts. Constructing bimetallic transition metal phosphides is a feasible strategy to meet the challenge. Here, an amorphous Co-Mo-P film supported on nickel foam (Co-Mo-P/NF) electrode is developed with bifunctional properties for both the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in alkaline seawater. Corresponding results indicate that the introduction of Mo can improve the active sites and regulate the intrinsic activity. Such a Co-Mo-P/NF behaves with prominent electrocatalytic activity towards both HER and OER, demanding low overpotentials of 193 and 352 mV at 100 mA cm‒2in alkaline seawater, respectively. Furthermore, the assembled electrolyzer demands a pronounced overall seawater splitting activity with a low cell voltage of 1.76 V to deliver 100 mA cm-2presenting excellent durability without obvious attenuation after 24 h continuous stability test. This work expands the horizon to develop transition metal-phosphorus electrocatalysts with robust and efficient activity for overall seawater splitting.

Activating Commercial Nickel Foam to a Highly Efficient Electrocatalyst for Oxygen Evolution Reaction through a Three-Step Surface Reconstruction.

It is highly desired to directly use commercial nickel foam (CNF) as an electrocatalyst for the oxygen evolution reaction (OER) via simple surface reconstruction. In our research, a simple three-step preactivation process was proposed to reconstruct CNF as an efficient OER catalyst, including calcination, high-voltage treatment, and immersing in electrolyte. The optimal CNF after three-step activation reaches an excellent OER performance of 228 and 267 mV at η10 and η100 in alkaline media and can tolerate long-term tests under a large current density of 500 mA·cm-2. The promotion of each step was explored. The calcination step leads to a reconstructive surficial morphology with an enlarged active surface, providing a prerequisite for the following construction steps. The high-voltage treatment changes the valence of surface Ni species, generating phases with higher catalytic activity, and the immersing process introduces Fe heteroatoms into the surface of CNF, boosting the catalytic performance of CNF through Ni-Fe interactions. This research provides a simple method of making high-performance catalysts with accessible nickel foam, a potential for large-scale application in practical industry, and new thinking for the manipulation of Ni-based catalysts.

Binary Ni-Fe layered double hydroxide on flexible nickel foam for the wide-range voltammetric detection of fibrinogen in simulated body fluid.

Fibrinogen, a circulating glycoprotein in the blood, is a potential biomarker of various health conditions. This work reports a flexible electrochemical sensor based on Ni-Fe layered double hydroxide (Ni-Fe LDH) coated on Nickel foam (Ni-Fe LDH/NF) to detect fibrinogen in simulated human body fluid (or blood plasma). The nanoflakes like morphology and hexagonal crystal structure of LDH, synthesized via urea hydrolysis assisted precipitation technique, are revealed by scanning electron microscopy (SEM) and powder x-ray diffraction (PXRD) techniques, respectively. The fabricated sensor exhibits linearity in a wide dynamic range covering the physiological concentration, from 1 ng ml-1to 10 mg ml-1, with a sensitivity of 0.0914 mA (ng/ml)-1(cm)-2. This LDH-based sensor is found to have a limit of detection (LOD) of 0.097 ng ml-1and a limit of quantification (LOQ) of 0.294 ng ml-1(S/N = 3.3). The higher selectivity of the sensor towards fibrinogen protein is verified in the presence of various interfering analytes such as dopamine, epinephrine, serotonin, glucose, potassium, chloride, and magnesium ions. The sensor is successful in the trace-level detection of fibrinogen in simulated body fluid with excellent recovery percentages ranging from 99.5% to 102.5%, proving the synergetic combination of 2D Ni-Fe layered double hydroxide and 3D nickel foam as a promising platform for electrochemical sensing that has immense potential in clinical applications.

The Superiority of TiO2 Supported on Nickel Foam over Ni-Doped TiO2 in the Photothermal Decomposition of Acetaldehyde.

Acetaldehyde decomposition was performed under heating at a temperature range of 25-125 °C and UV irradiation on TiO2 doped by metallic Ni powder and TiO2 supported on nickel foam. The process was carried out in a high-temperature reaction chamber, "The Praying MantisTM", with simultaneous in situ FTIR measurements and UV irradiation. Ni powder was added to TiO2 in the quantity of 0.5 to 5.0 wt%. The photothermal measurements of acetaldehyde decomposition indicated that the highest yield of acetaldehyde conversion on TiO2 and UV irradiation was obtained at 75 °C. The doping of nickel to TiO2 did not increase its photocatalytic activity. Contrary to that, the application of nickel foam as a support for TiO2 appeared to be highly advantageous because it increased the decomposition of acetaldehyde from 31 to 52% at 25 °C, and then to 85% at 100 °C in comparison with TiO2 itself. At the same time, the mineralization of acetaldehyde to CO2 doubled in the presence of nickel foam. However, oxidized nickel foam used as support for TiO2 was detrimental. Most likely, different mechanisms of electron transfer between Ni-TiO2 and NiO-TiO2 occurred. The application of nickel foam greatly enhanced the separation of free carriers in TiO2. As a consequence, high yields from the photocatalytic reactions were obtained.