Surface coating engineering of titanate anodes based on tannic acid-formaldehyde polymer chelating bismuth ions for advanced sodium-ion capacitors.

As a battery-type anode material for sodium ion capacitors (SICs), titanate (H2Ti2O5·H2O, HTO) exhibits good rate capability due to its layered structure, easy to insert Na+ ions and low potential during sodium-ion storage. However, the structure is unstable due to the lattice distortion resulting from the irreversible embedment of Na+ in the process of sodium storage. So there is a significant mismatch between the dynamic reaction of the HTO anode and the capacitive cathode. Surface coating engineering is a useful strategy for stabilizing the HTO structure, which is critical for improving the kinetic response. In this work, a surface coating technique is designed to enhance the surface of HTO nanoarrays on titanium foil by using the oligomers of tannic acid formaldehyde polymer (TAF) chelated Bi3+ ions (Bi-TAF). As a binder-free anode, HTO coated with Bi-TAF (HTO@Bi-TAF) exhibits more excellent capacity (335.2 mA h g-1, 0.1 A g-1), rate capability (212.3 mA h g-1, 2.0 A g-1), and cycle stability (97 % capacity maintenance following 2000 cycles at 1.0 A g-1) than HTO and HTO coated with TAF (HTO@TAF). At the sweep rate of 1.0 mV s-1, the kinetic investigation reveals that the capacitance contribution of HTO@Bi-TAF is 86 %. The SICs exhibit a significant energy/power density (89.4 Wh kg-1/250 W kg-1). This work shows that the Bi-TAF polymer coating has a dual effect of rate capability improvement and structural protection on the prepared HTO. This results in a reasonable and effective surface coating strategy that provides outstanding rate capability and extended cycle performance of titanium-based anode materials for SICs.

Experimental Study on the Chlorine-Induced Corrosion and Blister Formation of Steel Pipes Coated with Modified Polyethylene Powder.

In this study, chlorine-induced corrosion and blister formation on steel pipes (SPs) coated with modified polyethylene powder (MPP) were evaluated through various tests, including chlorine exposure, wet immersion, and temperature gradient experiments. The results confirmed that the extent of corrosion and iron leaching varied with the coating type as expected. In batch leaching tests, no corrosion was observed on modified polyethylene-coated steel pipes (MPCSPs) within a chlorine concentration range of 0 mg/L to 10 mg/L; similarly, there were no significant changes in specimen weight or iron levels. In contrast, the control group with uncoated SPs exhibited significant iron leaching and corrosion, a trend consistent in sequential leaching experiments. SEM analysis after a month of chlorine exposure revealed no significant corrosion on MPCSPs, and SEM-EDX confirmed no major changes in the carbon bond structure, indicating resistance to high chlorine concentrations. Comparative analysis of wet immersion and temperature gradient tests between MPCSP and conventional epoxy-coated SP (ECSP) specimens revealed that MPCSPs did not develop blisters even after 100 days of immersion, whereas ECSPs began showing blisters as early as 50 days. In temperature gradient tests, MPCSPs showed no blisters after 100 days, while ECSPs exhibited severe internal coating layer blisters.

Durable photobioreactor antibiofouling coatings for microalgae cultivation by photoreactive poly(2,2,2-trifluoroethyl methacrylate).

To improve the durability of the photobioreactor antibiofouling surface for microalgal cultivation, a series of photoreactive poly(2,2,2-trifluoroethyl methacrylate) (PTFEMA) were successfully synthesized and used to modify ethylene-vinyl acetate (EVA) films by a surface coating and UV light grafting method. Fourier transform infrared (FT-IR) spectra, X-ray photoelectron spectroscopy analysis (XPS) and fluorescence microscopy results indicated that PTFEMA were fixed successfully onto the EVA film surface through a covalent bond. During the microalgal adhesion assay, the number of EVA-PTFEMA film-adhered microalgae was 41.4% lower than that of the EVA film. Moreover, the number of microalgae attached to the EVA-PTFEMA film decreased by 61.7% after cleaning, while that of EVA film decreased by only 49.1%. It was found that the contact angle of EVA-PTFEMA film surface increased, and remained stable when immersed in acid and alkali solution for up to 90 days.HIGHLIGHTSDurable photobioreactor antibiofouling surfaces for microalgal cultivation were prepared successfully.The contact angle of antibiofouling coating surface remained stable in acid and base environment for 90 days.The attached microalgae on antibiofouling surface decreased 41.4% than those of unmodified surface.The attached microalgae on antibiofouling surface could be cleaned by 61.7% through changing the flow velocity of microalgal suspension.

The surface charge of electroactive materials governs cell behaviour through its effect on protein deposition.

The precise mechanisms underlying the cellular response to static electric cues remain unclear, limiting the design and development of biomaterials that utilize this parameter to enhance specific biological behaviours. To gather information on this matter we have explored the interaction of collagen type-I, the most abundant mammalian extracellular protein, with poly(vinylidene fluoride) (PVDF), an electroactive polymer with great potential for tissue engineering applications. Our results reveal significant differences in collagen affinity, conformation, and interaction strength depending on the electric charge of the PVDF surface, which subsequently affects the behaviour of mesenchymal stem cells seeded on them. These findings highlight the importance of surface charge in the establishment of the material-protein interface and ultimately in the biological response to the material. STATEMENT OF SIGNIFICANCE: The development of new tissue engineering strategies relies heavily on the understanding of how biomaterials interact with biological tissues. Although several factors drive this process and their driving principles have been identified, the relevance and mechanism by which the surface potential influences cell behaviour is still unknown. In our study, we investigate the interaction between collagen, the most abundant component of the extracellular matrix, and poly(vinylidene fluoride) with varying surface charges. Our findings reveal substantial variations in the binding forces, structure and adhesion of collagen on the different surfaces, which collectively explain the differential cellular responses. By exposing these differences, our research fills a critical knowledge gap and paves the way for innovations in material design for advanced tissue regeneration strategies.

Lanthanum doping and surface Li3BO3 passivating layer enabling 4.8 V nickel-rich layered oxide cathodes toward high energy lithium-ion batteries.

Single crystalline Ni-rich layered oxide cathodes show high energy density and low cost, have been regarded as one of the most promising candidates for next generation lithium-ion batteries (LIBs). Extending the cycling voltage window will significantly improve the energy density, however, suffers from bulk structural and interfacial chemistry degradation, leading to rapidly cycle performance deterioration. Here, we propose a dual-modification strategy to synthesize La doping and Li3BO3 (LBO) coating layers modified LiNi0.8Co0.1Mn0.1O2 (NCM811) by a facile one-step heating treatment processing. In-situ EIS and XRD, ex-situ XPS techniques are applied to demonstrate that the La diffused amorphous domains and Li3BO3 passivating layers dampen the lattice distortion, enhance the interfacial chemistry behavior as well as lithium ion transportation kinetics. Specifically, surface La doping amorphous domains successfully suppress the intense lattice stress and volume changes induced by the phase transitions during lithiation/delithiation, thus avoiding the intergranular crack and enhancing the mechanical stability of the material. Moreover, the LBO layer formed by the consumption of residual lithium prevents successive parasitic reactions at the interface as well as provides rapid Li-ion diffusion channels. Furthermore, the coating layer also diminishes the residual lithium compounds, increasing the atmosphere stability and safety of LIBs. Consequently, the La doping and LBO coating NCM811 exhibits an exceptional initial specific capacity (230.6 mAh/g) at 0.5C under a high cutoff voltage of 4.8 V, and a 73.8 % capacity retention following 100 cycles. In addition, a superior specific capacity of 133.8 mAh/g is provided even at a high current density (4C). Our work paves a promising road to tackle the integral structure deterioration and interfacial instability of Ni-rich cathodes.

Lithium-Ion Conductive Coatings for Nickel-Rich Cathodes for Lithium-Ion Batteries.

Nickel (Ni)-rich cathodes are among the most promising cathode materials of lithium batteries, ascribed to their high-power density, cost-effectiveness, and eco-friendliness, having extensive applications from portable electronics to electric vehicles and national grids. They can boost the wide implementation of renewable energies and thereby contribute to carbon neutrality and achieving sustainable prosperity in the modern society. Nevertheless, these cathodes suffer from significant technical challenges, leading to poor cycling performance and safety risks. The underlying mechanisms are residual lithium compounds, uncontrolled lithium/nickel cation mixing, severe interface reactions, irreversible phase transition, anisotropic internal stress, and microcracking. Notably, they have become more serious with increasing Ni content and have been impeding the widespread commercial applications of Ni-rich cathodes. Various strategies have been developed to tackle these issues, such as elemental doping, adding electrolyte additives, and surface coating. Surface coating has been a facile and effective route and has been investigated widely among them. Of numerous surface coating materials, have recently emerged as highly attractive options due to their high lithium-ion conductivity. In this review, a thorough and comprehensive review of lithium-ion conductive coatings (LCCs) are made, aimed at probing their underlying mechanisms for improved cell performance and stimulating new research efforts.

Phytic Acid-Promoted Deposition of Gold Nanoparticles with Grafted Cationic Polymer Brushes for the Construction of Synergistic Contact-Killing and Photothermal Bactericidal Coatings.

Medical implants are constantly facing the risk of bacterial infections, especially infections caused by multidrug resistant bacteria. To mitigate this problem, gold nanoparticles with alkyl bromide moieties (Au NPs-Br) on the surfaces were prepared. Xenon light irradiation triggered the plasmon effect of Au NPs-Br to induce free radical graft polymerization of 2-(dimethylamino)ethyl methacrylate (DMAEMA), leading to the formation of poly(DMAEMA) brush-grafted Au NPs (Au NPs-g-PDM). The Au NPs-g-PDM nanocomposites were conjugated with phytic acid (PA) via electrostatic interaction and van der Waals interaction. The as-formed aggregates were deposited on the titanium (Ti) substrates to form the PA/Au NPs-g-PDM (PAP) hybrid coatings through surface adherence of PA and the gravitational effect. Synergistic bactericidal effects of contact-killing caused by the cationic PDM brushes, and local heating generated by the Au NPs under near-infrared irradiation, conferred strong antibacterial effects on the PAP-deposited Ti (Ti-PAP) substrates. The synergistic bactericidal effects reduced the threshold temperature required for the photothermal sterilization, which in turn minimized the secondary damage to the implant site. The Ti-PAP substrates exhibited 97.34% and 99.97% antibacterial and antiadhesive efficacy, respectively, against Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli), compared to the control under in vitro antimicrobial assays. Furthermore, the as-constructed Ti-PAP surface exhibited a 99.42% reduction in the inoculated S. aureus under in vivo assays. In addition, the PAP coatings exhibited good biocompatibility in the hemolysis and cytotoxicity assays as well as in the subcutaneous implantation of rats.

Fractional-Order Electrical Modeling of Aluminum Coated via Plasma Electro-Oxidation and Thermal Spray Methods to Optimize Radiofrequency Medical Devices.

Active medical devices rely on a source of energy that is applied to the human body for specific purposes such as electrosurgery, ultrasounds for breaking up kidney stones (lithotripsy), laser irradiation, and other medical techniques and procedures that are extensively used. These systems must provide adequate working power with a commitment not to produce side effects on patients. Therefore, the materials used in these devices must effectively transmit energy, allow for security control, sense real-time variations in case of any issues, and ensure the implementation of closed-loop systems for control. This work extends to the experimental data adjustment of some different coating techniques based on plasma electro-oxidation (PEO) and thermal spray (TS) using fractional-order models. According to the physical structure of the coating in different coating techniques, Cole family models were selected. The experimental data were obtained by means of a vector network analyzer (VNA) in the frequency spectrum from 0.3 MHz to 5 MHz. The results show that some models from the Cole family (the single-dispersion model and inductive model) offered a goodness of fit to the experimental impedance in terms of RMSE error and a squared error R2 close to unity. The use of this type of fractional-order electrical model allows an adjustment with a very small number of elements compared to integer-order models, facilitating its use and a consequent reduction in instrumentation cost and the development of control devices that are more robust and easily miniaturized for embedded applications. Additionally, fractional-order models allow for more accurate assessment in industrial and medical applications.

Tailoring Zinc Ferrite Nanoparticle Surface Coating for Macrophage-Affinity Magnetic Resonance Imaging of Atherosclerosis.

Atherosclerosis is a chronic inflammatory disease characterized by the formation of atherosclerotic plaques, while macrophages as key players in plaque progression and destabilization are promising targets for atherosclerotic plaque imaging. Contrast-enhanced magnetic resonance imaging (CE-MRI) has emerged as a powerful noninvasive imaging technique for the evaluation of atherosclerotic plaques within arterial walls. However, the visualization of macrophages within atherosclerotic plaques presents considerable challenges due to the intricate pathophysiology of the disease and the dynamic behavior of these cells. Biocompatible ferrite nanoparticles with diverse surface ligands possess the potential to exhibit distinct relaxivity and cellular affinity, enabling improved imaging capabilities for macrophages in atherosclerosis. In this work, we report macrophage-affinity nanoparticles for magnetic resonance imaging (MRI) of atherosclerosis via tailoring nanoparticle surface coating. The ultrasmall zinc ferrite nanoparticles (Zn0.4Fe2.6O4) as T1 contrast agents were synthesized and modified with dopamine, 3,4-dihydroxyhydrocinnamic acid, and phosphorylated polyethylene glycol to adjust their surface charges to be positively, negatively, and neutrally charged, respectively. In vitro MRI evaluation shows that the T1 relaxivity for different surface charged Zn0.4Fe2.6O4 nanoparticles was three higher than that of the clinically used Gd-DTPA. Furthermore, in vivo atherosclerotic plaque MR imaging indicates that positively charged Zn0.4Fe2.6O4 showed superior MRI efficacy on carotid atherosclerosis than the other two, which is ascribed to high affinity to macrophages of positively charged nanoparticles. This work provides improved diagnostic capability and a better understanding of the molecular imaging of atherosclerosis.

Fabrication of silver nanoparticles loaded acacia gum/chitosan nanogel to coat the pipe surface for sustainable inhibiting microbial adhesion and biofilm growth in water distribution systems.

Biofilm formation on the inner surfaces of pipes poses significant threats to water distribution systems, increasing maintenance costs and public health risks. To address this immense issue, we synthesized a nanogel formulation comprising acacia gum (AG) and chitosan (Cs), loaded with varying concentrations of silver nanoparticles (AgNPs), for using as an antimicrobial coating material. AgNPs were synthesized using AG as a reducing and stabilizing agent, exhibiting absorbance at 414 nm. The preparation of AgNPs was proved using TEM. Bactericidal efficacy was assessed against E. coli, Klebsiella pneumoniae, Enterococcus faecalis, and Bacillus subtilis. Using the dipping coating method, two pipe materials (polypropylene (PP) and ductile iron (DI)) were successfully coated. Notably, AgNPs2@AGCsNG nanogel exhibited potent antibacterial action against a wide range of pathogenic bacteria. Toxicity tests confirmed nanogel safety, suggesting broad applications. High EC50% values underscored their non-toxic nature. This research proposes an effective strategy for biofilm prevention in water systems, offering excellent antibacterial properties and biocompatibility. AG and Cs nanogels loaded with AgNPs promise to enhance water quality, reduce maintenance prices, and protect human public health in water distribution networks.

Preparation of Bio-Based Polyurethane Coating from Citrullus colocynthis Seed Oil: Characterization and Corrosion Performance.

In this study, a new epoxidized oil from Citrullus colocynthis seed oil (CCSO) was obtained for a potential application in the formulation of polyurethane coatings. Initially, the fatty acid composition of CCSO was determined by gas chromatography-mass spectrometry (GC-MS). Subsequently, the epoxidation of CCSO was performed with in situ generated peracetic acid, which was formed with hydrogen peroxide (30 wt.%) and glacial acetic acid and catalyzed with sulfuric acid. The reaction was continued at a molar ratio of 1.50:1.0 of hydrogen peroxide to double bond (H2O2:DB) for 6 h at a controlled temperature of 60 °C. The resulting epoxidized oil was then used to produce a bio-based polyol by hydroxylation. The molar ratio of epoxy groups to methanol and distilled water was maintained at 1:11:2, and the reaction was carried out for 2 h at a controlled temperature of 65 °C. The major functional groups of the epoxidized oil and its polyol were validated by Fourier-transform infrared (FT-IR) and proton nuclear magnetic resonance (1H NMR) spectroscopies. A polyurethane (PU) coating was produced from the synthesized polyol and 3HDI isocyanurate, keeping the molar ratio of NCO:OH at 1:1. The resulting PU coating was then applied to glass and aluminum panels (Al 1001). After the film was cured, the properties of the PU coating were evaluated using various techniques including pencil hardness, pendulum hardness, adhesion, gloss, chemical resistance, and EIS tests. The results show that the PU coating obtained from CCSO is a promising new raw material for coating applications.

Edible nano-encapsulated cinnamon essential oil hybrid wax coatings for enhancing apple safety against food borne pathogens.

Post-harvest losses of fruits due to decay and concerns regarding microbial food safety are significant within the produce processing industry. Additionally, maintaining the quality of exported commodities to distant countries continues to pose a challenge. To address these issues, the application of bioactive compounds, such as essential oils, has gained recognition as a means to extend shelf life by acting as antimicrobials. Herein, we have undertaken an innovative approach by nano-encapsulating cinnamon-bark essential oil using whey protein concentrate and imbibing nano-encapsulates into food-grade wax commonly applied on produce surfaces. We have comprehensively examined the physical, chemical, and antimicrobial properties of this hybrid wax to evaluate its efficacy in combatting the various foodborne pathogens that frequently trouble producers and handlers in the post-harvest processing industry. The coatings as applied demonstrated a static contact angle of 85 ± 1.6°, and advancing and receding contact angles of 90 ± 1.1° and 53.0 ± 1.6°, respectively, resembling the wetting properties of natural waxes on apples. Nanoencapsulation significantly delayed the release of essential oil, increasing the half-life by 61 h compared to its unencapsulated counterparts. This delay correlated with statistically significant reductions (p = 0.05) in bacterial populations providing both immediate and delayed (up to 72 h) antibacterial effects as well as expanded fungal growth inhibition zones compared to existing wax technologies, demonstrating promising applicability for high-quality fruit storage and export. The utilization of this advanced produce wax coating technology offers considerable potential for bolstering food safety and providing enhanced protection against bacteria and fungi for produce commodities.

Polydopamine based photothermal/photodynamic synchronous coating modified intraocular lens for efficient and safer posterior capsule opacification prevention.

Posterior capsule opacification (PCO), as one of the most common late complications after intraocular lens (IOL) implantation in cataract surgery, seriously affects patients' postoperative vision and surgical satisfaction, and can only be treated by laser incision of the posterior capsule. Although drug eluting coating modification have been proved to inhibit PCO effectively, the complicated coating methods and the potential toxicity of the antiproliferative drugs hinders its actual application. In this study, an indocyanine green (ICG) loaded polydopamine (PDA) coating modified IOL (IP-IOL) was designed to prevented PCO. In vitro and in vivo studies have shown that IP-IOL can effectively eliminate lens epithelial cells and significantly reduce the degree of PCO. At the same time, it still has good imaging quality and optical properties. Furthermore, both the near-infrared irradiation and ICG loaded PDA coating modified IOLs have proved to possess high biological safety to eyes. Thus, with easy preparation and safer near-infrared irradiated photothermal/photodynamic synchronous properties, such ICG loaded PDA coating provides an effective yet easier and safer PCO prevention after IOL implantation.

In Vitro and Preclinical Antitumor Evaluation of Doxorubicin Liposomes Coated with a Cholesterol-Based Trimeric ß-D-Glucopyranosyltriazole.

The coating of liposomes with polyethyleneglycol (PEG) has been extensively discussed over the years as a strategy for enhancing the in vivo and in vitro stability of nanostructures, including doxorubicin-loaded liposomes. However, studies have shown some important disadvantages of the PEG molecule as a long-circulation agent, including the immunogenic role of PEG, which limits its clinical use in repeated doses. In this context, hydrophilic molecules as carbohydrates have been proposed as an alternative to coating liposomes. Thus, this work studied the cytotoxicity and preclinical antitumor activity of liposomes coated with a glycosyl triazole glucose (GlcL-DOX) derivative as a potential strategy against breast cancer. The glucose-coating of liposomes enhanced the storage stability compared to PEG-coated liposomes, with the suitable retention of DOX encapsulation. The antitumor activity, using a 4T1 breast cancer mouse model, shows that GlcL-DOX controlled the tumor growth in 58.5% versus 35.3% for PEG-coated liposomes (PegL-DOX). Additionally, in the preliminary analysis of the GlcL-DOX systemic toxicity, the glucose-coating liposomes reduced the body weight loss and hepatotoxicity compared to other DOX-treated groups. Therefore, GlcL-DOX could be a promising alternative for treating breast tumors. Further studies are required to elucidate the complete GlcL-DOX safety profile.

Reduced Cell Adhesion on LightPLAS-Coated Implant Surfaces in a Three-Dimensional Bioreactor System.

Most implants used in trauma surgery are made of steel and remain inside the body only temporarily. The strong tissue interaction of such implants sometimes creates problems with their explantation. Modified implant surfaces, which decrease tissue attachment, might allow an easier removal and therefore a better outcome. Such a modification must retain the implant function, and needs to be biocompatible and cost-effective. Here, we used a novel VUV-light (Vacuum-Ultraviolett)-based coating technology (LightPLAS) to generate coated stainless-steel plates. The tested LightPLAS coating only had an average thickness of around 335 nm, making it unlikely to interfere with implant function. The coated plates showed good biocompatibility according to ISO 10993-5 and ISO 10993-12, and reduced cell adhesion after four different time points in a 2D cell culture system with osteoblast-like MG-63 cells. Furthermore, we could show decreased cell adhesion in our 3D cell culture system, which mimics the fluid flow above the implant materials as commonly present in the in vivo environment. This new method of surface coating could offer extended options to design implant surfaces for trauma surgery to reduce cell adhesion and implant ingrowth. This may allow for a faster removal time, resulting in shorter overall operation times, thereby reducing costs and complication rates and increasing patient wellbeing.

Surface Modification on Nickel Rich Cathode Materials for Lithium-Ion Cells: A Mini Review.

Nickel-rich (Ni-rich) layered oxides are considered as the most promising cathode candidates for lithium-ion cells owing to their high theoretical specific capacity. However, the higher nickel content endows structural deformation through unwanted phase transitions and parasitic side reactions that lead to capacity fading upon prolonged cycling. Hence, a deep understanding of the chemistry and structural behaviour is essential for developing Ni-rich Lithium Nickel Cobalt Manganese oxide (NCM) cathode-based high-energy batteries. The present review focuses on the different challenges associated with Ni-rich NCM materials and surface modification as a strategy to solve the issues associated with NCM materials, assessment of several coating materials, and the recent developments in the surface modification of Ni-rich NCMs, with an in-depth discussion on the impact of coating on the degradation mechanism.

Separation Performance of Membranes Containing Ultrathin Surface Coating of Metal-Polyphenol Network.

Metal-polyphenol networks (MPNs) are being used as versatile coatings for regulating membrane surface chemistry and for the formation of thin separation layers. The intrinsic nature of plant polyphenols and their coordination with transition metal ions provide a green synthesis procedure of thin films, which enhance membrane hydrophilicity and fouling resistance. MPNs have been used to fabricate tailorable coating layers for high-performance membranes desirable for a wide range of applications. Here, we present the recent progress of the use of MPNs in membrane materials and processes with a special focus on the important roles of tannic acid-metal ion (TA-Mn+) coordination for thin film formation. This review introduces the most recent advances in the fabrication techniques and the application areas of TA-Mn+ containing membranes. In addition, this paper outlines the latest research progress of the TA-metal ion containing membranes and summarizes the role of MPNs in membrane performance. The impact of fabrication parameters, as well as the stability of the synthesized films, is discussed. Finally, the remaining challenges that the field still faces and potential future opportunities are illustrated.

Pseudomonas fragi biofilm on stainless steel (at low temperatures) affects the survival of Campylobacter jejuni and Listeria monocytogenes and their control by a polymer molybdenum oxide nanocomposite coating.

Pseudomonas spp. are widely distributed bacteria on surfaces in the food production and processing environment, where they form extracellular polymeric substance rich biofilms that interact with other bacteria. In this study, the influence of biofilm of Pseudomonas fragi ATCC 4973 on Listeria monocytogenes ATCC 19115 and Campylobacter jejuni NCTC 11168 was investigated at 5 °C and 15 °C on stainless steel in broth and food homogenates (fish or chicken meat). Stainless steel was then coated with PVDF-HFP/PVP/MoO3 nanocomposite and examined for surface changes (scanning electron microscope, static contact angle, Vickers hardness and elastic modulus). The effect of the prepared nanocomposite coating on P. fragi and on L. monocytogenes and C. jejuni was evaluated in mono- and co-culture. P. fragi produced more biofilm at 15 °C than at 5 °C, especially when food homogenates were used as growth media. Co-cultivation with pathogens did not affect biofilm production by P. fragi, but significant changes were observed in L. monocytogenes and C. jejuni, resulting in a decrease and increase, respectively, in the determined number of culturable biofilm cells. The first change was probably due to competition for the surface, and the second to the oxygen gradient. Stainless steel was then coated with a PVDF-HFP/PVP/MoO3 nanocomposite, which was characterised by lower roughness and higher wettability, but lower hardness compared to uncoated stainless steel. The prepared nanocoating showed bactericidal activity when tested in phosphate buffered saline. When used in food homogenates, a reduction of over 95 % in bacterial counts was observed. An abundant biofilm of P. fragi proved protective to L. monocytogenes and C. jejuni against the functionalised nanocomposite surface when tested in food homogenates. The control of spoilage Pseudomonas spp., which are common in the food production and processing environment, is important for reducing the contamination of food with spoilage bacteria and with pathogens such as L. monocytogenes and C. jejuni, which may be present in the same environment. The PVDF-HFP/PVP/MoO3 nanocomposite showed good potential for use as a coating for food contact surfaces, but possible migration of nanoparticles from the nanocomposite coating to food should be evaluated before its commercial use.

Surface decoration with leucine tetrapeptide: An antibacterial strategy against Gram-negative bacteria.

Surface-associated microbe contamination by Gram-negative bacteria poses a serious problem in medical care. Cationic peptides or polymers are the main materials used for antibacterial surface coating, but the positive charge may lead to blood coagulation. Therefore, exploiting surface coating which is free of positive charge and is effective for Gram-negative bacteria inactivation is in urgent need. In this study, inspired by the affinity between lipopolysaccharides of Gram-negative bacteria and Toll-like receptors of immune cells, we develop a leucine-based tetrapeptide coating strategy for combating Gram-negative bacteria. The obtained surface has excellent bactericidal activity against Gram-negative bacteria like Pseudomonas aeruginosa and Escherichia coli. A 1 mm2 coated glass surface could kill > 9.9 × 104 CFU bacteria in 1 h and has nearly no damage to mammal cells. Moreover, this surface coating strategy could be applied on various surfaces like glass slices, glass capillary cavity and thermoplastic polyurethane slices. And the coated surface could largely mitigate the microbe contamination in an in vivo subcutaneous implantation. This work paves a new way for antibacterial surface-coating which is behaving no positive charge and is of great importance for biomedical devices.

Effect of femoral stem surface coating on clinical and radiographic outcomes of cementless primary total hip arthroplasty: a patient-matched retrospective study.

PURPOSE: This study aims to determine whether changing the stem coating grants superior outcomes at a minimum follow-up of five years. METHODS: Retrospective review of a consecutive series of primary total hip arthroplasties (THAs) operated by direct anterior approach between 01/01/2013 and 31/12/2014. Two stems were compared, which were identical except for their surface coating; "the Original stem" was fully coated with hydroxyapatite (HA), while "the ProxCoat stem" was proximally coated with plasma-sprayed titanium and HA. Matching was performed. Clinical assessment included modified Harris hip score (mHHS), Oxford hip score (OHS), and forgotten joint score (FJS). Radiographic assessment evaluated alignment, subsidence, pedestal formation, heterotopic ossification, radiolucent lines ≥ 2 mm, spot welds, cortical hypertrophy, and osteolysis. RESULTS: 232 hips received the Original stem and 167 the ProxCoat stem, from which respectively five hips (2.2%) and no hips (0%) underwent revision. Matching identified two groups of 91 patients, with comparable patient demographics. At > five years follow-up, there were no differences in OHS (16 ± 6 vs 15 ± 5; p = 0.075) nor FJS (81 ± 26 vs 84 ± 22; p = 0.521), but there were differences in mHHS (89 ± 15 vs 92 ± 12; p = 0.042). There were no differences in alignment, subsidence, pedestal formation, heterotopic ossification, cortical hypertrophy, and osteolysis. There were differences in prevalence of proximal radiolucent lines (12% vs 0%; p < 0.001) and distal spot welds (24% vs 54%; p < 0.001). CONCLUSION: At a minimum follow-up of five years, this study on matched patients undergoing primary THA found that ProxCoat stems results in significantly fewer radiolucent lines, more spot welds, and less revisions than Original stems, thus suggesting better bone ingrowth.