Precision of polyether ether ketone (PEEK) or cobalt-chrome implant bar fit to implants after mechanical cycling.

Based on its mechanical properties, PEEK (polyether-ether-ketone) might be useful in restorative procedures. In oral rehabilitation, its viability has been studied mainly for prostheses and dental implants. AIM: The aim of this study was to evaluate the fit accuracy of dental implant bars made of either PEEK or cobalt-chrome submitted to cycling mechanics. MATERIALS AND METHOD: This was an experimental in vitro study, where units were treated with two implants and mini-abutments, joined by cobalt-chrome or polyether-ether-ketone PEEK bars. A total 20 bars were prepared (n=10 per group) and subjected to mechanical cycling tests (1 million cycles on the distal cantilever of the bar in the vertical direction, 120N and sinusoidal loading, at a frequency of 2Hz). The fit at the abutment/implant interface was measured before and after cycling, and the counter-torque of the vertical screw of the mini abutments was measured after cycling, using a digital torquemeter. Data were analyzed by three-way ANOVA and Tukey's test at 5% significance level. RESULTS: No statistically significant interaction was found among the three factors considered (bar material, implant positioning and mechanical cycling) (p = 0.592). No significant difference was identified in the interaction between bar material and implant positioning (p = 0.321), or between implant positioning and mechanical cycling (p = 0.503). The association between bar material and mechanical cycling was statistically significant (p = 0.007), with the cobalt-chrome bar resulting in greater misfit with mechanical cycling. There was no difference in counter-torque values between groups. CONCLUSIONS: The PEEK bar provided better fit of the mini abutments to the implants, even after mechanical cycling. The counter-torque of the screws was similar in all scenarios considered.

O PEEK (Poli-éter-éter-cetona) é um material considerado para uso em procedimentos restauradores devido às suas propriedades mecânicas. Na reabilitação oral, sua viabilidade tem sido estudada principalmente para uso em próteses e implantes dentários. Objetivos: O objetivo deste estudo foi avaliar a precisão da adaptação de duas barras diferentes do tipo protocolo confeccionadas em PEEK ou Cobalto-Cromo, após serem submetidas à mecânica ciclística. Materiais e Método: As unidades experimentais foram constituídas por barras confeccionadas em Poli-ether-ether-Ketone (PEEK) e em Cobalto-Cromo (Co-Cr). Trata-se de um estudo experimental, in vitro, onde verificou-se unidades constituídas por dois implantes e mini pilares unidos com barras de Cobalto-Cromo ou PEEK. Foram confeccionados um total de 20 barras (n=10 em cada grupo) e as barras foram submetidas a ensaios de ciclagem mecânica (1 milhão de ciclos no cantilever distal da barra no sentido vertical, 120N e carregamento senoidal, a uma frequência de 2Hz). Antes e após a ciclagem realizou-se a mensuração da desadaptação na interface pilar/implante e após a ciclagem foi medido o contra-torque do parafuso vertical dos mini-pilares através de torquímetro digital TQ 8800 (LT Lutron, Taiwan). Os dados foram submetidos a ANOVA a três critérios e teste de Tukey ao nível de significância a 5%. Resultados: Constatou-se que não houve interação estatisticamente significativa entre os três fatores estudados, ou seja, entre o material da barra, o posicionamento do implante e a ciclagem mecânica (p = 0,592). Também não se identificou diferença estatística significativa da interação entre o material da barra e o posicionamento do implante (p = 0,321), nem entre o posicionamento do implante e a ciclagem mecânica (p = 0,503). Já a associação entre o material da barra e a ciclagem mecânica foi estatisticamente significativa (p = 0,007), onde a barra de Cobalto-Cromo resultou em maior desadaptação com a ciclagem mecânica. Não houve diferença nos valores dos contra-torques entre os grupos. Conclusões: Conclui-se que a barra de protocolo fabricada em PEEK proporcionou melhor adaptação dos mini pilares aos implantes mesmo após a ciclagem mecânica. Por fim, o contra-torque dos parafusos foi semelhante em todos os cenários avaliados.

Is All-on-four effective in case of partial mandibular resection? A 3D finite element study.

INTRODUCTION: The aim of the work is to analyze stress distribution on 3D Finite Element (FE) models at bone, implant, and framework level of different designs for fixed implant-supported prostheses in completely edentulous patients, comparing results on whole and partially resected mandibles. MATERIALS AND METHODS: 3D anisotropic FE models of a whole and of a partially resected mandible were created using a TC scan of a cadaver's totally edentulous mandible. Two types of totally implant-supported rehabilitation were simulated, with four implants: parallel fixtures on whole mandible and on resected mandible, All-on-four-configured fixtures on whole mandible and on partially resected mandible. A superstructure comprising only metal components of a prosthetic framework were added, while stress distribution and its maximum values were analyzed at bone, implant, and superstructure level. RESULTS: The results highlight that: (1) implant stresses are greater on the whole mandible than on the resected one; (2) framework and cancellous-bone stresses are comparable in all cases; (3) on the resected mandible, maximum stress levels at the cortical-bone/implant interface are higher than in whole-mandible rehabilitation. The opposite applies for maximum stresses on external cortical bone, measured radially with respect to the implant from the point of maximum stress at the interface. DISCUSSION: On the resected mandible, All-on-four configuration proved biomechanically superior to parallel implants considering radial stresses on implants and cortical bone. Still, maximum stresses increase at the bone/implant interface. A design with four parallel implants minimizes the stress on a resected mandible while, on the whole mandible, the All-on-four rehabilitation proves superior at all levels (bone, implant, and framework).

Bond strength of composite resin/universal adhesive to dentin submitted to radiotherapy / Fuerza de unión de resina compuesta/adhesivo universal a dentina sometida a radioterapia

Aim: To evaluate the bond strength of a universal adhesive system to dentin submitted to radiotherapy. Materials and Methods: Sixty extracted human teeth were divided into two groups (n = 30): without radiotherapy (control); with radiotherapy, according to the adhesive protocol (n=15): ER-etch-and-rinse (acid + Single Bond Uni-versal); SE-self-etch (Single Bond Universal). The analyzes were shear bond strength (SBS) (n=10), failure pattern (n=10) and scanning electron microscopy (n=5). Data was analyzed by a two-way ANOVA (α =0.05). Results: The radiotherapy decreased SBS of the restorative material to dentin (p<0.0001). The ER protocol provided lower bond strength values (p<0.001). The predominant type of fracture without radiotherapy was mixed (SE), cohesive to the material (ER). Both protocols presented adhesive failures with radiotherapy. Teeth had a hybrid layer and long resin tags (without radiotherapy) and few tags (with radiotherapy). Conclusions: The SE adhesive mode favors the shear bond strength of resin to dentin in teeth submitted to radiotherapy.

Objetivo: Evaluar la fuerza de adhesión de un sistema adhesivo universal a la dentina sometida a radioterapia. Materiales y Métodos: Sesenta dientes humanos extraídos se dividieron en dos grupos (n = 30): sin radioterapia (control); con radioterapia, según protocolo adhesivo (n=15): ER-grabado y enjuague (ácido + Single Bond Universal); autograbado SE (Single Bond Universal). Los análisis ejecutados fueron resistencia al cizallamiento (SBS) (n=10), patrón de falla (n=10) y microscopía electrónica de barrido (n=5). Los datos se sometieron al test de ANOVA de dos vías (α =0,05). Resultados: La radioterapia disminuyó la SBS del material restaurador a la dentina (p<0,0001). El protocolo ER proporcionó valores de fuerza de unión más bajos (p<0,001). El tipo de fractura predominante sin radioterapia fue mixta (SE), cohesiva al material (ER). Ambos protocolos presentaron fallas adhesivas con radioterapia. Los dientes tenían una capa híbrida y colas de resina largas (sin radioterapia) o pocas colas de resina (con radioterapia). Conclusión: El modo adhesivo SE favorece la resistencia al corte de la resina a la dentina en dientes sometidos a radioterapia.

Effect of partial restorative treatment on stress distributions in non-carious cervical lesions: a three-dimensional finite element analysis.

BACKGROUND: Partial restoration combined with periodontal root coverage surgery can be applied to the treatment of non-carious cervical lesions (NCCLs) accompanied with gingival recessions in clinical practice. However, the feasibility of NCCL partial restorative treatment from a biomechanical perspective remains unclear. This study aimed to investigate the effect of partial restorations on stress distributions in the NCCLs of mandibular first premolars via three-dimensional finite element analysis. METHODS: Three-dimensional finite element models of buccal wedge-shaped NCCLs in various locations of a defected zenith (0 mm, 1 mm, and 2 mm) were constructed and divided into three groups (A, B, and C). Three partially restored NCCL models with different locations of the lower restoration border (1 mm, 1.5 mm, and 2 mm), and one completely restored NCCL model were further constructed for each group. The following restorative materials were used in all restoration models: composite resin (CR), glass-ionomer cement (GIC), and mineral trioxide aggregate (MTA). The first principal stress distributions under buccal oblique loads of 100 N were analyzed. Restoration bond failures were also evaluated based on stress distributions at dentin-restoration interfaces. RESULTS: When the partial restoration fully covered the defected zenith, the first principal stress around the zenith decreased and the maximum tensile stress was concentrated at the lower restoration border. When the partial restoration did not cover the defected zenith, the first principal stress distribution patterns were similar to those in unrestored models, with the maximum tensile stress remaining concentrated at the zenith. As the elastic modulus of the restorative material was altered, the stress distributions at the interface were not obviously changed. Restoration bond failures were not observed in CR, but occurred in GIC and MTA in most models. CONCLUSIONS: Partial restorations that fully covered defected zeniths improved the stress distributions in NCCLs, while the stress distributions were unchanged or worsened under other circumstances. CR was the optimal material for partial restorations compared to GIC and MTA.

A new look toward crown-to-implant ratio.

PURPOSE: To clarify how crown-to-implant ratio (C-I ratio) influences the bone biomechanically with its two components: crown height and implant length. METHODS: This three-dimensional finite element study was performed in two phases. The first phase aimed to show the influence of the C-I ratio on the stresses in the peri-implant bone and the second phase to reveal the impact of each of the two components of the C-I ratio: crown height and implant length. During analyses, all models were subject to three different loading conditions - axial, buccolingual, and oblique. RESULTS: The crown-to-implant ratio was significantly influential on stress distribution in the peri-implant bone. However, the crown's height was significantly more prominent than the length of the implant. The most substantial amount of stress was seen when long crowns were combined with off-axial loads. Being mostly dominated by the height of the crown and far less by the implant's length, the C-I ratio is not balanced and seems not to be a predictive parameter in implant dentistry. CLINICAL SIGNIFICANCE: Crown-to-implant ratio is recommended to be assessed by its two components: crown height and implant length because the former impacts stresses significantly more than the latter.

Comparison of multiforce nickel-titanium wires to multistrand wires without force zones in bending and torque measurements.

PURPOSE: The aim was to compare rectangular multiforce nickel-titanium (NiTi) wires to rectangular wires with only one force zone. Both types of wires are primarily intended for use during the levelling phase of orthodontic treatment. Thus, basic mechanical properties were examined by means of a three-point bending test. Torque expression, which is dependent on both wire parameters and interslot distances, was analyzed using the Orthodontic Measurement and Simulation System (OMSS). MATERIAL/METHODS: Four multizone products were tested: DuoForce™ (Forestadent, Pforzheim, Germany), TriTanium™ (American Orthodontics, Sheboygan, WI, USA), Triple Force™ (ODS, Kisdorf, Germany), Bio-Active™ (GC, Breckerfeld, Germany), and two multistrand products without force zones: a nine-strand NiTi, TurboWire™ (Ormco, Orange, CA, USA) and an eight-strand stainless steel (SS) wire, Multibraid™ (GAC, Dentsply Sirona, York, PA, USA). All the wires had the dimension 0.40 mmâ€¯× 0.56 mm (0.016 inchâ€¯× 0.022 inch) except the nine-strand NiTi wire TurboWire™, which had a dimension of 0.43 mmâ€¯× 0.65 mm (0.017 inchâ€¯× 0.025 inch). Six different bracket systems in the 0.018 inch slot system were chosen: the conventional brackets discovery® and discovery® smart (Dentaurum, Ispringen, Germany), the active self-ligating brackets InOvation™ and InOvation™ mini (GAC, Dentsply Sirona, York, PA, USA) and the passive self-ligating brackets Carrière™ (ODS, Kisdorf, Germany) and BioPassive® (Forestadent, Pforzheim, Germany). The first set-up was a three-point bending test according to DIN EN ISO 15841. For the second experiment, the bracket products glued on a maxilla model were combined with the wire products. The torque moments arising during torqueing of the wires between +20° and -20° were measured in three positions: first incisor, canine and second bicuspid. RESULTS: Bending tests confirmed variation of the force corresponding to the force zones. The nine-strand NiTi wire TurboWireTM and the eight-strand SS wire Multibraid™ did not show any variation dependent on the tested area. Torque-moments generated by the multizone wires were higher compared to the braided wires. The nine-strand NiTi wire showed the lowest moments in spite of the higher dimension. As expected, increasing the interbracket distance reduced the torque moments. CONCLUSION: The tests verified the existence of multiple force zones in the NiTi wires for forces and moments, respectively. As the torque-moments arising from the multizone wires were rather high, it is not recommended to use these wires as a first "leveling wire" in orthodontic treatment, especially in extremely crowded cases.

Comparison of the Polymerization Shrinkage of Eclipse Resin for Prostheses with Conventional Acrylic Resins / Comparación de la Contracción de Polimerización de la Resina Eclipse para Prótesis con Resinas Acrílicas Convencionales

ABSTRACT: The objective of this study was to compare the polymerization shrinkage of Eclipse photopolymerization resin for prosthesis based on urethane dimethacrylate (UDMA) with that of three heat-cured acrylic resins based on polymethyl methacrylate (PMMA) after the polymerization process and immersion in water. A total of 40 prostheses were fabricated on a standard metallic upper edentulous model: group 1, Eclipse; group 2, Triplex hot; group 3, Veracril; and group 4, Lucitone 199. Subsequently, the polymerization contraction was tested using a microscope in which measurements were made in micrometres at 3 points located in the middle parts of the right and left sides and the middle part of the palate at three time points once the prosthesis was completed, after 30 days of immersion in water for 8 hours a day at a temperature of 37 °C, and after cutting the prosthesis at the level of the second premolar. ANOVA revealed that the contraction of the polymerization no statistically significant differences between the groups, (P> 0.05). The type of resin and its interaction with the processing method behaves similarly for all test resins. The Veracril heat-cured resin obtained the lowest contraction value in the three measurements (mm) and the highest value was obtained with the Eclipse photopolymerization resin. The Eclipse resin exhibited no lower polymerization shrinkage compared to conventional acrylic resins based on polymethyl methacrylate (PMMA), however it was not significantly affected by immersion in water.

RESUMEN: El objetivo de este estudio fue comparar la contracción de polimerización de la resina de fotopolimerización Eclipse para prótesis basadas en dimetacrilato de uretano (UDMA) con la de tres resinas acrílicas curadas con calor a base de polimetacrilato de metilo (PMMA) después del proceso de polimerización e inmersión en agua. Se fabricaron un total de 40 prótesis en un modelo edéntulo superior metálico estándar: grupo 1, Eclipse; grupo 2, triplex caliente; grupo 3, veracril; y grupo 4, Lucitone 199. Posteriormente, la contracción de la polimerización se probó utilizando un microscopio en el que se realizaron mediciones en micrometros en 3 puntos ubicados en las partes medias de los lados derecho e izquierdo y la parte media del paladar en tres puntos de tiempo una vez la prótesis se completó, después de 30 días de inmersión en agua durante 8 horas al día a una temperatura de 37 °C, y después de cortar la prótesis a nivel del segundo premolar. ANOVA reveló que la contracción de la polimerización no presenta diferencias estadísticamente significativas entre los grupos, (P> 0,05). El tipo de resina y su interacción con el método de procesamiento se comportan de manera similar para todas las resinas de prueba. La resina curada con calor Veracril obtuvo el valor de contracción más bajo en las tres mediciones (mm) y el valor más alto se obtuvo con la resina de fotopolimerización Eclipse. La resina Eclipse no mostró una contracción de polimerización menor en comparación con las resinas acrílicas convencionales basadas en polimetilmetacrilato (PMMA), sin embargo, no se vio afectada significativamente por la inmersión en agua.

Stress analysis of maxillary central incisors endodontically -treated with varying ferrule heights and three different post dowel materials - a finite element analysis / Análisis de tensión de los incisivos centrales superiores tratados endodónticamente con diferentes alturas de férula y tres materiales diferentes de clavija posterior: un análisis de elementos finitos

Statement of problem : fracture of endodontically treated teeth is reduced by the use of a post with ferrule, but the effect of different ferrule configurations and dowel materials is not clear. Purpose: to evaluate the effect of ferrules with different configurations and heights on the stress of endodontically treated teeth restored with three different post and dowel materials. Materials and Methods: fifteen models of maxillary central incisors restored with porcelain fused to metal crowns were obtained using pro engineer software. the models were divided into three groups, each consisting of five models with ferrule heights of 0mm, 2mm, 4mm, 2mm with oblique fracture, 4mm with oblique fracture, the models under group GFR were restored with fiberglass reinforced post (GFR) and composite core build-up, group NiCr with a custom cast post metal alloy (NiCr), and group Zr with zirconia post (Zr) and composite core build-up. an oblique load of 100N and 150N at an angle of 135 degrees was applied to the palatal surface of the tooth, a vertical load of 100N and 150N at an angle of 90 degrees was applied to the incisal tip of the tooth. The maximum principal stress and the von mises stress was calculated for the remaining tooth structure and post apex using the finite element analysis (FEA) software. Results: the maximum von misses stress was observed in the apex of the post (p<0.05). Group Zr showed the highest mean stress (6.39Mpa) followed by group NiCr (5.65Mpa). There was a significant difference between post and between NiCr and Zr post for 2mm and 4mm ferrule height, while for 0mm ferrule there was a significant difference between the GFR and NiCr groups (p<0.05). Under oblique load, the maximum mean stress was observed in remaining tooth structures while for vertical load, it was observed at the apex of the post. Regarding ferrule heights, there were significant differences between 0mm-2mm, and 0mm-4mm uniform ferrule in post apex in the case of NiCr posts (p<0.05). Absence of ferrule resulted in higher stress for the NiCr group. Conclusion: higher loads that led to fracture were observed only at the apex of the post. Zirconia posts (group Zr) had higher fracture loads, whereas absence of ferrule resulted in higher fracture load with custom cast posts (group NiCr). Fracture thresholds were high on the remaining tooth structure for all the dowel systems especially for composite core build up irrespective of ferrule height and configuration. Clinical implications: appropriate selection of post and dowel materials in different configurations of ferrule heights ensures clinical success.

Indicación del problema: la fractura de los dientes tratados endodónticamente se reduce mediante el uso de un poste con férula, pero el efecto de diferentes configuraciones de férula y materiales de clavija no está claro. Propósito: evaluar el efecto de los casquillos con diferentes configuraciones y alturas sobre el estrés de los dientes tratados endodónticamente restaurados con tres materiales diferentes de postes y tacos. materiales y métodos: quince modelos de incisivos centrales superiores restaurados con porcelana fundida a coronas de metal se obtuvieron con el software Pro Engineer. Los modelos se dividieron en tres grupos, cada uno de los cuales consta de cinco modelos con alturas de casquillo de 0mm, 2mm, 4mm, 2mm con fractura oblicua, 4mm con fractura oblicua. los modelos del grupo GFR fueron restaurados con poste reforzado con fibra de vidrio (GFR) y acumulación de núcleo compuesto, grupo nicr con una aleación de metal de poste fundido personalizado (NiCr) y grupo Zr con poste de zirconia (Zr) y acumulación de núcleo compuesto. se aplicó una carga oblicua de 100N y 150N en un ángulo de 135º a la superficie palatina del diente. se aplicó una carga vertical de 100N y 150N en un ángulo de 90º a la punta incisal del diente. la tensión principal máxima y la tensión de von mises se calcularon para la estructura dental restante y después del vértice utilizando el software de análisis de elementos finitos (FEA). Resultados: el estrés máximo de von falta se observó en el vértice de la publicación (p<0.05). El grupo Zr mostró el mayor estrés medio (6.39Mpa) seguido del grupo NiCr (5.65Mpa). Hubo una diferencia significativa entre la publicación NiCr y Zr para la altura de la férula de 2mm y 4mm, mientras que para la férula de 0mm hubo una diferencia significativa entre los grupos GFR y NiCr (p<0,05), bajo la carga oblicua, la tensión media máxima en las estructuras dentales restantes, mientras que para la carga vertical, se observó en el vértice del poste. En cuanto a las alturas de la férula, hubo diferencias significativas entre la férula uniforme de 0mm-2mm y de 0mm-4mm en el post-apex en el caso de los postes de NiCr (p<0.05), la ausencia de férula dio como resultado un mayor estrés para el grupo NiCr. Conclusión: las cargas más altas que llevaron a la fractura se observaron solo en el vértice del poste; Los postes de zirconia (grupo Zr) tuvieron mayores cargas de fractura, mientras que la ausencia de férula dio como resultado una mayor carga de fractura con postes moldeados personalizados (NiCr de grupo). Los umbrales de fractura fueron altos en la estructura dental restante para todos los sistemas de clavijas, especialmente para la acumulación de núcleos compuestos independientemente de la altura y configuración de la férula. Implicaciones clínicas: la selección adecuada de materiales de postes y tacos en diferentes configuraciones de alturas de férulas asegura el éxito clínico.

Force decay evaluation of latex and non-latex orthodontic intraoral elastics: in vivo study

ABSTRACT Objective: This clinical study was conducted in order to evaluate force decay over time of latex and non-latex orthodontic intraoral elastics. Methods: Patients (n = 15) were evaluated using latex and non-latex elastics in the periods of : 0, 1, 3, 12 and 24 hours. The rubber bands were transferred to the testing machine (EMIC DL-500 MF), and force values were recorded after stretching the elastic to a length of 25mm. Paired t test was applied and analysis of variance (ANOVA) was used to evaluate the variation of force generated. LSD (Fisher's least significant difference) post-hoc test was thus employed. Results: As regards the initial forces (zero time), the values of force for non-latex elastic were slightly higher than for the latex elastic. In the subsequent times, the forces generated by the latex elastic showed higher values. Regarding the material degradation, at the end of 24 hours the highest percentage was observed for non-latex elastic. Conclusions: The latex elastics had a more stable behavior during the studied period, compared with non-latex.

RESUMO Objetivo: o objetivo deste estudo clínico foi avaliar e comparar o comportamento dos elásticos de látex e não látex quanto à perda de força ao longo do tempo. Método: os pacientes (n = 15) foram avaliados usando ambos os tipos de material (látex e não látex) em cada tempo: 0, 1, 3, 12 e 24 horas. Os elásticos foram transferidos para a máquina de ensaios mecânicos (EMIC DL-500 MF) e os valores de força foram registrados após a distensão dos elásticos a uma distância de 25 mm. Foi aplicado o teste t pareado, e a análise de variância (ANOVA) foi realizada para verificar a variação das forças geradas em todos os tempos estudados. Em seguida, o teste post-hoc LSD (Fisher's least significant difference) foi aplicado. Resultados: quanto às forças iniciais (tempo zero), os valores de força dos elásticos não látex foram ligeiramente maiores do que dos elásticos de látex. Nos tempos subsequentes, as forças geradas pelos elásticos de látex apresentaram valores superiores às geradas pelos elásticos não látex. Em relação à degradação do material, ao fim do período de 24 horas, o maior percentual foi observado pelos elásticos não látex. Conclusões: os elásticos de látex apresentaram comportamento mais estável durante o período de estudo, em comparação aos não látex.

Finite element analysis of slot wall deformation in stainless steel and titanium orthodontic brackets during simulated palatal root torque.

INTRODUCTION: Torque applied on anterior teeth is vital for root positioning and stability. The aim of this study was to evaluate the detailed slot wall deformation in stainless steel (SS) and titanium (Ti) edgewise brackets during palatal root torque using finite element analysis. METHODS: A finite element model was developed from a maxillary central incisor SS bracket (0.022 in). The generated torque values from an SS rectangular archwire (0.019 × 0.025 in) while twisting from 5° to 40° were obtained experimentally by a spine tester, and the calculated torque force was applied in the bracket slot. The deformations of the slot walls in both SS and Ti brackets were measured at various locations. RESULTS: There were gradual increases in the deformations of both bracket slot walls from the bottom to top locations. In the SS bracket slot for the 40° twist, the deformations were 9.28, 36.8, and 44.8 µm in the bottom, middle, and top slot wall locations, respectively. Similarly, in the Ti bracket slot for the 40° twist, the deformations were 39.2, 62.4, and 76.2 µm in the bottom, middle, and top slot wall locations, respectively. The elastic limits were reached at 28° for SS and at 37° for Ti. CONCLUSIONS: Both SS and Ti bracket slots underwent deformation during torque application. There are variations in the deformations at different locations in the slot walls and between the materials.

Implant inclination and horizontal misfit in metallic bar framework of overdentures: analysis by 3d-fea method

Abstract The aim of this study was to evaluate by three-dimensional finite element analysis (3D-FEA) the biomechanics involved in bar-framework system for overdentures. The studied factors were latero-lateral angulation in the right implant (-10, -5, 0, 5 and 10 degrees), and different bar cross-sections (circular, Hader and oval) presenting horizontal misfits (50 or 150 µm) on the opposite implant. Positive angulation (5 and 10 degrees) for implant inclination to mesial position, negative angulation (-5 and -10 degrees) for distal position, and zero degree for parallel implants. The von Mises stresses evaluated the bar, screw and the implant; maximum principal, minimum principal and shear stress analyses evaluated the peri-implant bone tissue. Parallel implants provide lower stress in alveolar bone tissue; mesial inclined bars showed the most negative effect on prosthetic structures and implants. In conclusion, bar cross-section showed no influence on stress distribution for peri-implant bone tissue, and circular bar provided better behavior to the prosthetic system. Higher stress concentration is provided to all system as the misfit increases.

Resumo O objetivo neste estudo foi avaliar por meio do método por elemento finito tridimensional (3D-AEF) a biomecânica envolvida na infraestrutura do sistema barra-clipe para overdentures. Os fatores de estudo foram inclinação mésio-distal entre implantes (-10, -5, 0, 5, 10 graus) e diferentes seções transversais da barra metálica (circular, oval e Hader) com desajuste horizontal (50 e 150 µm). Valores de inclinação positivas (5 e 10 graus) indicam inclinação do implante para mesial e valores negativos (-5 e -10 graus) mostram inclinação para distal, enquanto zero grau indica implantes paralelos. Valores de tensões equivalentes de von Mises foram utilizadas nos sistemas barra, parafuso e implante. Tensão máxima e mínima principal, e cisalhante foram utilizadas para análise do osso alveolar peri-implante. Implantes paralelos promoveram menores tensões em tecido peri-implante; as inclinações para mesial apresentaram piores resultados para as estruturas protéticas e implantes. As diferentes seções transversais da barra não mostraram influência na distribuição de tensões no osso alveolar peri-implante. Concluindo, a barra circular apresentou melhores resultados para os componentes protéticos e maiores valores de tensões foram observados em todos os modelos na medida que o desajuste aumentou.

Evaluation of shear bond strength and shear stress on zirconia reinforced lithium silicate and high translucency zirconia

This study evaluated the shear stress distribution on the adhesive interface and the bond strength between resin cement and two ceramics. For finite element analysis (FEA), a tridimensional model was made using computer-aided design software. This model consisted of a ceramic slice (10x10x2mm) partially embedded on acrylic resin with a resin cement cylinder (Ø=3.4 mm and h=3mm) cemented on the external surface. Results of maximum principal stress and maximum principal shear were obtained to evaluate the stress generated on the ceramic and the cylinder surfaces. In order to reproduce the in vitro test, similar samples to the computational model were manufactured according to ceramic material (Zirconia reinforced lithium silicate - ZLS and high translucency Zirconia - YZHT), (N=48, n=12). Half of the specimens were submitted to shear bond test after 24h using a universal testing machine (0.5 mm/min, 50kgf) until fracture. The other half was stored (a) (180 days, water, 37ºC) prior to the test. Bond strength was calculated in MPa and submitted to analysis of variance. The results showed that ceramic material influenced bond strength mean values (p=0.002), while aging did not: YZHT (19.80±6.44)a, YZHTa (17.95±7.21)a, ZLS (11.88±5.40)b, ZLSa (11.76±3.32)b. FEA results showed tensile and shear stress on ceramic and cylinder surfaces with more intensity on their periphery. Although the stress distribution was similar for both conditions, YZHT showed higher bond strength values; however, both materials seemed to promote durable bond strength.

3-D finite element analysis of the effects of post location and loading location on stress distribution in root canals of the mandibular 1st molar

Abstract Objective The purpose of this study was to evaluate, by using finite element analysis, the influence of post location and occlusal loading location on the stress distribution pattern inside the root canals of the mandibular 1st molar. Material and Methods Three different 3-D models of the mandibular 1st molar were established: no post (NP) - a model of endodontic and prosthodontic treatments; mesiobuccal post (MP) - a model of endodontic and prosthodontic treatments with a post in the mesiobuccal canal; and distal post (DP) - a model of endodontic and prosthodontic treatments with a post in the distal canal. A vertical force of 300 N, perpendicular to the occlusal plane, was applied to one of five 1 mm2 areas on the occlusal surface; mesial marginal ridge, distal marginal ridge, mesiobuccal cusp, distobuccal cusp, and central fossa. Finite element analysis was used to calculate the equivalent von Mises stresses on each root canal. Results The DP model showed similar maximum stress values to the NP model, while the MP model showed markedly greater maximum stress values. The post procedure increased stress concentration inside the canals, although this was significantly affected by the site of the force. Conclusions In the mandibular 1st molar, the distal canal is the better place to insert the post than the mesiobuccal canal. However, if insertion into the mesiobuccal canal is unavoidable, there should be consideration on the occlusal contact, making central fossa and distal marginal ridge the main functioning areas.

Stress analysis of irradiated human tooth enamel using finite element methods.

The objectives of this project were to use finite element methods to determine how changes in the elastic modulus due to oral cancer therapeutic radiation alter the distribution of mechanical stresses in teeth and to determine if observed failures in irradiated teeth correlate with changes in mechanical stresses. A thin slice section finite element (FE) model was constructed from micro CT sections of a molar tooth using MIMICS and 3-Matic software. This model divides the tooth into three enamel regions, the dentin-enamel junction (DEJ) and dentin. The enamel elastic modulus was determined in each region using nano indentation for three experimental groups namely - control (non-radiated), in vitro irradiated (simulated radiotherapy following tooth extraction) and in vivo irradiated (extracted subsequent to oral cancer patient radiotherapy) teeth. Physiological loads were applied to the tooth models at the buccal and lingual cusp regions for all three groups (control, in vitro and in vivo). The principal tensile stress and the maximum shear stress were used to compare the results from different groups since it has been observed in previous studies that delamination of enamel from the underlying dentin was one of the major reasons for the failure of teeth following therapeutic radiation. From the FE data, we observed an increase in the principal tensile stress within the inner enamel region of in vivo irradiated teeth (9.97 ± 1.32 MPa) as compared to control/non-irradiated teeth (8.44 ± 1.57 MPa). Our model predicts that failure occurs at the inner enamel/DEJ interface due to extremely high tensile and maximum shear stresses in in vivo irradiated teeth which could be a cause of enamel delamination due to radiotherapy.

Distribution of stress on TMJ disc induced by use of chincup therapy: assessment by the finite element method

ABSTRACT Objective: To assess the distribution of stress produced on TMJ disc by chincup therapy, by means of the finite element method. Methods: a simplified three-dimensional TMJ disc model was developed by using Rhinoceros 3D software, and exported to ANSYS software. A 4.9N load was applied on the inferior surface of the model at inclinations of 30, 40, and 50 degrees to the mandibular plane (GoMe). ANSYS was used to analyze stress distribution on the TMJ disc for the different angulations, by means of finite element method. Results: The results showed that the tensile and compressive stresses concentrations were higher on the inferior surface of the model. More presence of tensile stress was found in the middle-anterior region of the model and its location was not altered in the three directions of load application. There was more presence of compressive stress in the middle and mid-posterior regions, but when a 50o inclined load was applied, concentration in the middle region was prevalent. Tensile and compressive stresses intensities progressively diminished as the load was more vertically applied. Conclusions: stress induced by the chincup therapy is mainly located on the inferior surface of the model. Loads at greater angles to the mandibular plane produced distribution of stresses with lower intensity and a concentration of compressive stresses in the middle region. The simplified three-dimensional model proved useful for assessing the distribution of stresses on the TMJ disc induced by the chincup therapy.

RESUMO Objetivo: avaliar, por meio do método dos elementos finitos, a distribuição das tensões no disco articular produzidas pela mentoneira ortopédica. Métodos: um modelo tridimensional simplificado do disco articular foi desenvolvido com o software Rhinoceros 3D e exportado para o software ANSYS. Uma carga de 4,9 N (500 gf) foi aplicada na superfície inferior do modelo, com inclinação de 30, 40 e 50o em relação ao plano mandibular Gônio-Mentoniano (GoMe). O ANSYS analisou, por meio do método dos elementos finitos, a distribuição das tensões presentes no modelo do disco articular para as diferentes angulações. Resultados: os resultados mostraram que a concentração das tensões de tração e compressão foi maior na superfície inferior do modelo. A tensão de tração foi mais presente na região média-anterior do modelo, e sua localização não se alterou nas três direções da aplicação da carga. A tensão de compressão foi mais presente nas regiões média e média-posterior do modelo, mas quando a carga a 50o foi aplicada, ela se concentrou na região média. As intensidades das tensões de tração e compressão diminuíram progressivamente à medida que a carga foi aplicada mais verticalmente. Conclusão: as tensões induzidas pela mentoneira ortopédica se localizaram principalmente na superfície inferior do modelo. As cargas com maior angulação em relação ao plano mandibular produziram uma distribuição de tensões com menor intensidade e uma concentração da tensão de compressão na região média do modelo. Um modelo tridimensional simplificado se mostrou útil na avaliação da distribuição das tensões no disco articular induzidas pela mentoneira ortopédica.

Quantification of intrusive/retraction force and moment generated during en-masse retraction of maxillary anterior teeth using mini-implants: A conceptual approach

ABSTRACT Objective: The aim of the present study was to clarify the biomechanics of en-masse retraction of the upper anterior teeth and attempt to quantify the different forces and moments generated using mini-implants and to calculate the amount of applied force optimal for en-masse intrusion and retraction using mini-implants. Methods: The optimum force required for en-masse intrusion and retraction can be calculated by using simple mathematical formulae. Depending on the position of the mini-implant and the relationship of the attachment to the center of resistance of the anterior segment, different clinical outcomes are encountered. Using certain mathematical formulae, accurate measurements of the magnitude of force and moment generated on the teeth can be calculated for each clinical outcome. Results: Optimum force for en-masse intrusion and retraction of maxillary anterior teeth is 212 grams per side. Force applied at an angle of 5o to 16o from the occlusal plane produce intrusive and retraction force components that are within the physiologic limit. Conclusion: Different clinical outcomes are encountered depending on the position of the mini-implant and the length of the attachment. It is possible to calculate the forces and moments generated for any given magnitude of applied force. The orthodontist can apply the basic biomechanical principles mentioned in this study to calculate the forces and moments for different hypothetical clinical scenarios.

RESUMO Objetivo: o objetivo do presente estudo foi explicar o funcionamento da biomecânica de retração em massa dos dentes anterossuperiores e tentar quantificar as diferentes forças e momentos gerados ao se usar mini-implantes, além de calcular a quantidade ideal de força a ser aplicada para se obter a intrusão/retração em massa ancorada em mini-implantes. Métodos: a força ideal necessária para se realizar a intrusão/retração em massa pode ser calculada por meio de fórmulas matemáticas simples. Dependendo da posição do mini-implante e da posição do acessório, a ele conectado, com relação ao centro de resistência do segmento anterior, obtêm-se desfechos clínicos diferentes. Aplicando certas fórmulas matemáticas, pode-se calcular com precisão a magnitude da força e do momento gerado nos dentes, para cada desfecho clínico. Resultados: a força ideal para se obter a intrusão/retração em massa dos dentes anterossuperiores é de 212 gramas por lado. A força aplicada em um ângulo de 5° a 16° em relação ao plano oclusal produz componentes de força de intrusão/retração que se encontram dentro dos limites fisiológicos. Conclusão: podem ser encontrados diferentes desfechos clínicos dependendo da posição do mini-implante e do comprimento do acessório. É possível calcular as forças e os momentos gerados para qualquer magnitude de força aplicada. Assim, o ortodontista clínico pode aplicar os princípios biomecânicos básicos apresentados nesse estudo para calcular as forças e os momentos em diferentes cenários clínicos hipotéticos.

Degradación de la Fuerza de los Elásticos Intermaxilares de Látex y no Látex / Force Degradation of Latex and Non Latex Intermaxillary Elastics

RESUMEN: El propósito del presente estudio fue comparar la degradación de la fuerza entre los elásticos de látex y no látex de 3/16" y 6 oz. La muestra consistió en 30 elásticos por grupo e intervalo de tiempo haciendo un total de 180 elásticos de látex y 180 de no látex. Se midió la fuerza inicial de 30 elásticos de látex y 30 de no látex. Los demás fueron sometidos a tracción estática bajo condiciones orales de humedad y temperatura por 1, 3, 6, 12 y 24 horas antes de la medición de la fuerza con un dinamómetro (Correx 250 g, Alemania). Se emplearon las pruebas de Friedman, Wilcoxon y la U de Mann-Whitney para determinar si existían diferencias significativas. Se encontró que los elásticos de látex presentaron una degradación media de la fuerza de 13,8 %, 17,4 %, 18,2 %, 21 % y 23,4 % a las 1, 3, 6, 12 y 24 horas, respectivamente. Los elásticos de no látex presentaron una degradación media de la fuerza de 32,5 %, 39,6 %, 44,4 %, 51,1 % y 56% a las 1, 3, 6, 12 y 24 horas, respectivamente. Cuando se compararon los valores hallados entre los dos tipos de elásticos en todos los momentos evaluados se encontraron diferencias estadísticamente significativas (p<0,001). Conclusión: La degradación de la fuerza para los elásticos de látex fue menor al de los elásticos de no látex en todos los intervalos de tiempo.

ABSTRACT: The purpose of this study was to compare the force degradation between latex and non latex elastic 3/16" 6oz. The sample consisted of 30 elastics per group and time interval, 180 latex and 180 non latex elastics were used. The initial force was measured in 30 latex elastics and 30 non latex elastics. Others elastics were subjected to static traction in conditions of humidity and temperature for 1, 3, 6, 12 and 24 hours. The force was measured with a dynamometer (Correx 250 g, Germany). Wilcoxon test and Mann-Whitney test was employed to determine significant differences. The latex elastics showed a mean force degradation of 13.8 % during the first hour, 17.4 % at 3 hours, 18.2 % at 6 hours, 21 % at 12 hours and 23. 4 % at 24 hours. The non elastics latex showed a mean force degradation of 32.5 % during the first hour, 39.6 % at 3 hours, 44.4 % at 6 hours, 51.1 % at 12 hours and 56% at 24 hours. It was concluded that the latex elastics force degradation was less than the non-elastics latex in all times.

Polymerization shrinkage stress of composite resins and resin cements - What do we need to know?

Abstract Polymerization shrinkage stress of resin-based materials have been related to several unwanted clinical consequences, such as enamel crack propagation, cusp deflection, marginal and internal gaps, and decreased bond strength. Despite the absence of strong evidence relating polymerization shrinkage to secondary caries or fracture of posterior teeth, shrinkage stress has been associated with post-operative sensitivity and marginal stain. The latter is often erroneously used as a criterion for replacement of composite restorations. Therefore, an indirect correlation can emerge between shrinkage stress and the longevity of composite restorations or resin-bonded ceramic restorations. The relationship between shrinkage and stress can be best studied in laboratory experiments and a combination of various methodologies. The objective of this review article is to discuss the concept and consequences of polymerization shrinkage and shrinkage stress of composite resins and resin cements. Literature relating to polymerization shrinkage and shrinkage stress generation, research methodologies, and contributing factors are selected and reviewed. Clinical techniques that could reduce shrinkage stress and new developments on low-shrink dental materials are also discussed.

Biomechanical evaluation of different osteosynthesis methods after mandibular sagittal split osteotomy in major advancements.

The aim of this study was to assess the biomechanical stability of six different osteosynthesis methods after sagittal split osteotomy. Sixty polyurethane hemimandibles were divided into two groups, with six subgroups in each. After 10-mm advancement of the distal segment (group 1) and 10-mm advancement combined with 20° counterclockwise rotation (group 2), the bone segments were fixed using 2.0-mm plates/screws as follows: subgroup A, one conventional straight plate; subgroup B, two conventional straight plates; subgroup C, one conventional sagittal plate; subgroup D, one locking straight plate; subgroup E, two locking straight plates; subgroup F, one locking sagittal plate. The hemimandibles were tested for compressive strength by three-point biomechanical test, until there was 3mm of displacement between the segments. The fixations showed better performance in group 1 than in group 2 in all cases, with statistical significance for subgroups A, C, and D. In both groups, the use of two straight miniplates showed the most resistance, followed by the sagittal miniplates. However, in counterclockwise rotations, no statistically significant difference was found between two conventional straight plates and the sagittal locking plate. This study shows that the use of two plates is the form of fixation with the minimum displacement. If the clinician opts to use one plate, a sagittal plate is the best alternative.

Frecuencia, severidad y ubicación de erupciones acneiformes en hombres y mujeres tras una cirugía ortognática: estudio descriptivo longitudinal / Frequency, severity and location of acneiform eruptions in men and women after orthognathic surgery: longitudinal descriptive study

Describir la frecuencia de erupciones acneiformes y/o exacerbaciones de un acné previo tras una cirugía ortognática. La muestra consta de 57 pacientes (n=57) de ambos sexos, sometidos a una cirugía ortognática, los cuales fueron evaluados en: el preoperatorio (0-7 días previos); en distintas etapas de la cirugía; postoperatorio inmediato (7 ­ 15 días post cirugía) y postoperatorio mediato (30 ­ 40 días postquirúrgicos). En todos los controles clínicos mencionados se determinó la presencia/ausencia, ubicación, severidad y diagnóstico de las erupciones acneiformes. El 52,6 % de los pacientes sometidos a cirugía ortognática presentaron erupciones acneiformes, siendo mayores en las mujeres en comparación con los hombres. La severidad de las erupciones acneiformes es mayor en el postoperatorio inmediato en comparación al preoperatorio y postoperatorio mediato. La ubicación más frecuente del acné corresponde a la región frontal, tanto en el preoperatorio (22,8 %) como en el postoperatorio inmediato (31,6 %). En el postoperatorio mediato la zona más frecuente es la geniana (39 %). La frecuencia de acné post cirugía ortognática es elevada, siendo mayor en mujeres que en hombres. La severidad de este acné es mayor en el postoperatorio inmediato. La región frontal corresponde a la zona más frecuente de aparición de las erupciones acneiformes en el postoperatorio inmediato y la zona geniana en el postoperatorio mediato. El diagnóstico de estas erupciones acneiformes corresponde a un acné esteroidal, por lo que se puede sugerir un posible plan de tratamiento, con el fin de mejorar el postoperatorio de las pacientes y evitar, en lo posible, futuras manifestaciones en nuevas pacientes sometidas a este tipo de cirugía.

Describe the frequency of acneiform eruptions and / or exacerbations of a previous acne after orthognathic surgery. The sample consisted of 57 patients (n = 57) of both genders, undergoing orthognathic surgery, who were evaluated with a follow-up of 2 postoperative months, at different stages of surgery; Preoperative (0-7 days), immediate postoperative (7-15 days) and mediate postoperative (30-40 days). The presence / absence, location, severity and diagnosis of acneiform eruptions were determined in all clinical controls. The frequency of acneiform eruptions corresponds to 52.6 % of patients undergoing orthognathic surgery, being higher in women compared to men in relation to the presence of acneiform eruptions and / or exacerbations of a previous acne after the intervention. The severity of acneiform eruptions is greater in the immediate postoperative period compared to the preoperative and mediate postoperative period. The most frequent location to be found in the facial region is in the frontal area, both in the preoperative (22.8 %) and in the immediate postoperative period (31.6 %). In the postoperative period, the most frequent is the genial area (39 %). The appearance of acneiform eruptions corresponds to steroidal acne. The frequency of acne post orthognathic surgery is high, being higher in women than in men. The severity of this acne is greater in the immediate postoperative period. The frontal region corresponds to the most frequent area of onset of acneiform eruptions in the immediate postoperative period and the genial area in the postoperative period. The diagnosis of these acneiform eruptions corresponds to a steroidal acne, so it is possible to suggest a possible treatment plan, in order to improve the postoperative of the patients and to avoid, as far as possible, future manifestations in new patients undergoing this type of surgery.