A green procedure for the determination of bioavailable forms of aluminum in natural waters by electrothermal atomic absorption spectroscopy combined with microextraction technique.

Aluminum is a prevalent element in nature, but bioavailable forms of aluminum are toxic to plants, animals, and humans. The present study is dedicated to the development of an ecologically friendly, fast, simple, reliable, sensitive, and accurate improved procedure for the determination of subtrace concentrations of bioavailable forms of aluminum in natural waters. The procedure includes the separation and pre-concentration of bioavailable forms of aluminum using vortex-assisted liquid-liquid microextraction (VALLME) of ionic associates with salicylaldehyde 4-picolinhydrazone (SAPH) and sodium dodecyl sulfate (DDSNa) by isoamylacetate (200 µl) and direct electrothermal atomic absorption spectroscopy (ET AAS). The SAPH reagent interacts only with water-soluble forms of aluminum. SAPH is used for the pre-concentration of bioavailable forms of aluminum as well as a chemical modifier; it increases the absorbance and the precision of the analytical signal of aluminum. The calibration curve shows the linear dependence in the range of 0.05-86 µg⋅L-1 of the aluminum concentration (R2 = 0.992), with the limit of detection at 0.015 µg⋅L-1 and the limit of quantification at 0.05 µg⋅L-1. The accuracy of the proposed procedure for bioavailable forms of aluminum determination was verified on model solutions and against a reference method on natural samples of river and lake waters (RSD 3.2-5.2%, recovery 97.1-103.4%).

L-cysteine mediated rapid separation of Hg2+ and MeHg+ by anion-exchange HPLC.

Owing to the on-going emission of Hg into the global environment, new insight into their bioinorganic chemistry in mammals is urgently required to better understand their adverse health effects and analytical methods to quantify Hg2+ and MeHg+ in environmental samples are needed. Analytical separations can help to address both of these needs. While Hg2+ and MeHg+ have been most frequently separated by cation and reversed-phase (RP) HPLC, we here report on using anion-exchange (AEX) HPLC in conjunction with a flame atomic absorption spectrometer (FAAS) to observe the retention behavior of these mercury species in the pH range 5.0-8.0 using mobile phases comprised of 10 mM l-cysteine (Cys) in 100 mM phosphate buffer. The results obtained for pH 5.0 served as a starting point to develop a rapid HPLC separation for these mercurials. The addition of 5-20 % methanol (MeOH) to this mobile phase revealed that MeOH did not appreciably change the retention of Hg2+, but significantly reduced the retention of MeHg+. A 15 % MeOH-containing mobile phase offered the best compromise between achieving a rapid baseline separation in <400 s at affordable costs. To assess the suitability and robustness of the developed AEX-HPLC separation method for the analysis of environmental samples an inductively coupled plasma atomic emission spectrometer (ICP-AES) was employed as the mercury-specific detector. The developed AEX-HPLC-ICP-AES method allowed to achieve detection limits of 1.5 ppm for Hg2+ and 2.9 ppm for MeHg+ and was successfully applied to analyze wastewater that had been spiked with Hg2+ and MeHg+.

Molecular engineering of a new method for effective removal of cadmium from water.

Cadmium (Cd) is a widespread and highly toxic environmental pollutant, seriously threatening animal and plant growth. Therefore, monitoring and employing robust tools to enrich and remove Cd from the environment is a major challenge. In this work, by conjugating a fluorescent indicator (CCP) with a functionalized glass slide, a special composite material (CCPB) was constructed to enrich, remove, and monitor Cd2+ in water rapidly. Then Cd2+ could be effectively eluted by immersing the Cd-enriched CCPB in an ethylenediaminetetraacetic acid (EDTA) solution. With this, the CCPB was continuously reused. Its recovery of Cd2+was above and below 100 % after multiple uses by flame atomic absorption spectrometry (FAAS), which was excellent for practical use in enriching and removing Cd2+ in real aqueous samples. Therefore, CCPB is an ideal material for monitoring, enriching, and removing Cd2+ in wastewater, providing a robust tool for future practical applications of Cd enrichment and removal in the environment.

Micro solid phase extraction of lead and cadmium using functionalized nanodiamonds@CuAl2O4@HKUST-1 nanocomposite for FAAS analysis in food and water samples.

This study focuses on the development and application of a novel nanocomposite (functionalized nanodiamonds@CuAl2O4@HKUST-1)-based µ-SPE method for the sensitive and selective extraction of Pb and Cd from food and water samples. The technique offers high sensitivity and selectivity, allowing accurate measurement of these metals at trace levels. The detection limit is 0.031 µg kg-1 for Cd and 0.052 µg kg-1 for Pb, with a relative standard deviation of 1.7 % for Cd and 4.8 % for Pb. The method was successfully applied to real samples and efficiently quantified Pb and Cd in food and natural water samples. The highest concentrations were found in red lentils (0.274 µg kg-1 Pb) and fresh mint (0.197 µg kg-1Cd), but still below recommended limits set by FAO/WHO (300 µg kg-1 for Pb and 200 µg kg-1 for Cd). It promises to ensure food safety, monitor environmental contamination, and informs regulatory decisions to protect public health.

Disruption of a three-component solution as a novel strategy for Cu and Ni extraction from vegetable oils for their determination by GF AAS.

In this work, we propose a novel approach for extracting Cu and Ni from vegetable oils (which can be expanded to other metals). The method is based on the transference of the analytes to an aqueous acid phase due to the disruption of a three-component solution. The extraction was carried out in two steps. In the first step, a three-component solution was prepared comprising the sample, 1-octanol, and HNO3 solution. Next, the homogeneous system was disrupted by adding 1.0 mL of deionized water, and two phases were formed. The aqueous extract deposited in the bottom of the flask was collected with a micropipette, and Cu and Ni were determined by graphite furnace atomic absorption spectrometry (GF AAS). The developed method presented limits of quantification (LOQ) of 0.25 and 0.17 ng g-1 for Cu and Ni, respectively, and was successfully applied in the analysis of eleven oil samples from different origins.

Analytical application of flower-shaped nickel nanomaterial for the preconcentration of manganese in domestic wastewater samples.

In this study, detection sensitivity of the conventional flame atomic absorption spectrophotometer (FAAS) for the determination of manganese (Mn2+) was enhanced by employing a preconcentration method from wastewater samples. Flower-shaped Ni(OH)2 nanomaterials were synthesized and used as sorbent material in preconcentration procedure. With the aim of attaining optimum experimental conditions, effective parameters of extraction method were optimized and these included pH of buffer solution, desorption solvent concentration and volume, mixing type and period, nanoflower amount, and sample volume. The detection limit of the optimized method was determined to be 2.2 µg L-1, and this correlated to about 41-fold enhancement in detection power relative to direct FAAS measurement. Domestic wastewater was used to test the feasibility of the proposed method to real samples by performing spike recovery experiments. The wastewater sample was spiked at four different concentrations of manganese, and the percent recoveries determined were in the range of 95-120%.

Trace nickel determination in seawater matrix using combination of dispersive liquid-liquid microextraction and triethylamine-assisted Mg(OH)2 method.

In order to eliminate the effects of seawater matrix on the precise/accurate determination of elements, new and efficient analytical procedure requires. In this study, co-precipitation method based on the triethylamine (TEA)-assisted Mg(OH)2 was performed to eliminate side-effects of seawater medium on the determination with flame atomic absorption spectrometry (FAAS) prior to the preconcentration of nickel by an optimized dispersive liquid-liquid microextraction (DLLME) method. Under the optimum conditions of the presented method, the limit of detection and quantification (LOD, LOQ) values obtained for nickel were found as 16.1 and 53.8 µg kg-1, respectively. Seawater samples collected from West Antarctic region were used for real sample applications to check the accuracy and applicability of developed method, and satisfying recovery results (86-97%) were obtained. In addition to this, the digital image-based colorimetric detection system and the UV-Vis system were applied to confirm the applicability of the developed DLLME-FAAS method in other analytical systems.

The importance of monitoring endocrine-disrupting chemicals and essential elements in biological samples of fertilizer industry workers.

Exposure to endocrine-disrupting chemicals (EDCs) can lead to adverse health effects, including immune and endocrine system disruption, respiratory problems, metabolic issues, diabetes, obesity, cardiovascular problems, growth impairment, neurological and learning disabilities, and cancer. Fertilizers, which contain varying levels of heavy metals, are known to pose a significant risk to human health, especially for those residing or working near fertilizer industries. This study aimed to investigate the levels of toxic elements in biological samples of individuals working in a fertilizer industry's quality control and production units and those residing within 100-500 m of the industry. Biological samples, including scalp hair and whole blood, were collected from fertilizer workers, individuals living in the same residential area, and control age-matched persons from nonindustrial areas. The samples were oxidized by an acid mixture before analysis using atomic absorption spectrophotometry. The accuracy and validity of the methodology were verified through certified reference materials from scalp hair and whole blood. The results showed that the concentrations of toxic elements, such as cadmium and lead, were higher in biological samples of quality control and production employees. In contrast, lower essential element levels (iron and zinc) were detected in their samples. These levels were higher than those found in samples collected from residents living within 10-500 m of the fertilizer manufacturing facilities and unexposed areas. This study highlights the significance of adopting better practices to reduce exposure to harmful substances and protect the health of fertilizer industry workers and the environment. It also suggests that policymakers and industry leaders should take measures to minimize exposure to EDCs and heavy metals to promote worker safety and public health. These measures could include implementing strict regulations and better occupational health practices to reduce toxic exposure and promote a safer work environment.

Unified analysis method for total and inorganic As determination in foodstuffs by hydride generation high-resolution continuum source quartz tube atomic absorption spectrometry.

A unified analytical method applicable to common foodstuff matrices was developed and characterized for total and inorganic arsenic determination by hydride generation high-resolution continuum source quartz tube atomic absorption spectrometry, which was established based on different sample preparation procedures. This new method was found to be interference-free and cost-effective in terms of reagents consumption for sample preparation and derivatization to arsine for the inorganic arsenic fraction. Microwave-assisted digestion in HNO3-H2O2 for total arsenic and extraction in 0.28 mol L-1 HNO3 by mechanical stirring in a water bath or ultrasound-assisted extraction in 0.01 mol L-1 HCl without separation of inorganic As, all coupled with arsine generation in 0.01 mol L-1 HCl medium with 0.6% NaBH4 in 0.01% NaOH in the presence of 0.2% L-cysteine was found to be suitable for all matrices. The results were statistically compared by applying Tukey's and Dunnett's multiple comparison methods (p > 0.05). The use of external calibration with As(III) standards and standard addition method for quantification showed the lack of non-spectral interferences from the multimineral matrices, resulting in a reliable method for total/inorganic As determination in various foodstuffs. The limits of detection for total/inorganic As using peak height measurement were 0.0044 ± 0.0005/0.0022 ± 0.0003 mg kg-1 (n = 25 days). The overall recovery for total/inorganic As in the certified reference materials was in the range of 98% ± 22%, and 99% ± 24% (k = 2). The extraction of inorganic As in 0.01 mol L-1 HCl and 0.28 mol L-1 HNO3 provided the recovery of 106% ± 25% and 100% ± 25% (k = 2), which was better than in 10 mol L-1 HCl. The precision of measurements in real samples of fish muscle, meat and organs, rice and rice-based baby foods with contents of 0.052-5.29 mg kg-1 total As and 0.005-0.063 mg kg-1 inorganic As was 9.8-18.8% and 8.7-32.0%, respectively, which was calculated based on the combined uncertainty.

Online column preconcentration for speciation and selective determination of Cr(III) in natural water samples using flow injection with chemiluminescence detection.

A simple, rapid, sensitive and inexpensive approach is described in this work based on a combination of solid-phase extraction of 8-hydroxyquinoline (8HQ), for speciation and preconcentration of Cr(III) and Cr(VI) in river water, and the direct determination of these species using a flow injection system with chemiluminescence detection (FI-CL) and a 4-diethylamino phenyl hydrazine (DEAPH)-hydrogen peroxide system. At different pH, the two forms of chromium [Cr(III) and Cr(VI)] have different exchange capacities for 8HQ, therefore two columns were constructed; the pH of column 1 was adjusted to pH 3 for retaining Cr(III) and column 2 was adjusted to pH 1 for retaining of Cr(VI). The sorbed Cr(III) and Cr(VI) species were eluted from columns using 3.0 ml of 0.1 N of HCl and 3.0 ml of 0.1 N of NaOH, respectively. The flow injection-chemiluminescence (FI-CL) method is based on light emitted due to the oxidation of DEAPH by the H2 O2 in the presence of Cr(III), which catalyzes the reaction. The flow cell is a transparent coiled tube made from glass (2.0 × 4.0, inner and outer diameter) and located close to the photodetector. The flow parameters: flow rate, sample volume, flow cell length, and distance to the CL detector were studied and optimized. Under optimum flow conditions, the Cr(III) concentration can be determined over the range 5-350 µg L-1 with a limit of detection of 1.2 µg L-1 , as the Cr(III) concentration is proportional to the intensity of the CL signal. The relative standard deviations (%) for 10 and 50 µg L-1 Cr(III) were 1.2% and 3.2%, respectively. The effects of Al(III), Cd(II), Zn(II), Hg(II), Pb(II), Co(II), Cu(II), Ni(II), Mn(II), Ca(II), and Fe(III) were investigated. The proposed method is highly selective and sensitive, enabling a rapid determination of the Cr(III) amount in the presence of other interfering metals. Finally, the FI-CL method was examined in five river water samples with excellent recoveries.

Deep eutectic solvent-based simultaneous complexation and preconcentration of nickel in Antarctic lake water samples for determination by flame atomic absorption spectrometry.

This study presents a simple, sensitive, and accurate method for the determination of nickel by flame atomic absorption spectrometry (FAAS). Prior to instrumental measurement, a deep eutectic solvent-based simultaneous complexation and preconcentration (DES-SCP) method was used to preconcentrate nickel from aqueous solution into measurable quantities. The efficiency of the extraction method was enhanced by forming a non-ionic complex of nickel using dithizone as ligand. By mixing the ligand with the DES extractant, simultaneous complexation and preconcentration of nickel were achieved in a single step. Under optimum conditions of the extraction method, the limit of detection (LOD) and the limit of quantification (LOQ) values were found to be 2.4 and 8.0 ng/mL, respectively. With respect to direct FAAS measurement, the developed method enhanced the sensitivity of nickel determination by about 169 folds. The accuracy and applicability of the developed method were evaluated by performing spike recovery experiments with lake water sampled from Antarctica. Satisfactory recovery results in the range of 94.0-113.7% were recorded and this validated the developed method as an efficient and green alternative for nickel determination.

Impacts of Smoking and Stomach Disorders on Essential Elements in Biological Samples of Cement and Glass Industrial Workers.

The infection caused by Helicobacter pylori (H. pylori) disrupts the metabolism and absorption of essential trace elements. Stomach disorders are related to changes in essential trace element metabolism caused by increased toxic metal exposure and H. pylori infection. The aim of the work is to link the development of stomach-related illnesses to an imbalance of essential trace and toxic metals. We have investigated the variations in essential trace elements such zinc (Zn), iron (Fe), and copper and toxic metals like lead (Pb) and cadmium (Cd) in biological (scalp hair, blood) samples of glass and cement workers. The study participants are further divided into smokers and nonsmokers, as well as diseased (gastric ulcer, irritable bowel syndrome, and chronic ulcer) and exposed referents (non-diseased industrial workers). Biological samples of age-matched (40-60 years) male subjects living in non-industrial areas were gathered for comparative purposes. After a pre-concentration method, the drinking water of industrial and domestic areas was analysed for both toxic metals. Microwave-aided acid digestion was used to oxidise the matrices of biological samples before atomic absorption spectrometer analysis of selected metals. Toxic metal levels in both industries' drinking water were much higher than those found in domestically treated water (p < 0.01). Industrial workers suffering different types of stomach disorders have two to three times higher Pb and Cd concentrations than age-matched referents. Toxic metals are found in higher concentrations in smoker referents and diseased patients' biological samples than in nonsmoker subjects. The findings of this study suggested that Pb and Cd toxicity's immunological effects may be associated to an increased vulnerability to chronic infections.

Rapid, Simultaneous, and Automatic Determination of Lead and Cadmium in Cereals with a New High Performance Composite Hollow Cathode Lamp Coupled to Graphite Furnace Atomic Absorption Spectrometry.

A simple, rapid, sensitive, accurate, and automatic graphite furnace atomic absorption spectrometry (GFAAS) method for detecting Cd and Pb in cereals is presented. This method enables the simultaneous determination of Cd and Pb in cereals with a pre-treatment method of diluted acid extraction and a high-performance lead-cadmium composite hollow-cathode lamp (LCC-HCL), and it realizes automatic determination from sample weighing to result output through an automatic diluted acid extraction system. Under the optimization, Pb and Cd in cereals were simultaneously and automatically detected in up to 240 measurements in 8 h. The LOD and LOQ of this method were 0.012 and 0.040 mg·kg-1 for Pb, and 0.0014 and 0.0047 mg·kg-1 for Cd, respectively. The results of the four certified reference materials were satisfied; there was no significant difference compared with the ICP-MS method according to a t-test, and the RSDs were less than 5% for Cd and Pb. The recoveries of naturally contaminated samples compared with the ICP-MS method were favorable, with 80-110% in eight laboratories. The developed method is rapid, low-cost, and highly automated and may be a good choice for grain quality discrimination and rapid analysis of Cd and Pb in different institutions.

Fast Detection of Cadmium in Chocolate by Solid Sampling Electrothermal Vaporization Atomic Absorption Spectrometry and Its Application on Dietary Exposure Risk Assessment.

In this work, a rapid detection method using solid sampling electrothermal vaporization atomic absorption spectrometry (SS-ETV-AAS) was established for cadmium in chocolate. The instrumental system includes a solid sampling ETV unit, a catalytic pyrolysis furnace, an AAS detector, and a gas supply system with only an air pump and a hydrogen generator. Herein, MgO material with 1.0−1.5 mm particle size was first employed to replace the kaolin filler previously used to further shorten the peak width and to thereby improve the sensitivity. With 350 mL/min of air, a chocolate sample was heated for 25 s from 435 to 464 °C to remove water and organic matrices; then, after supplying 240 mL/min hydrogen and turning down air to 120 mL/min, a N2/H2 mixture gas was formed to accelerate Cd vaporization from chocolate residue under 465 to 765 °C. Under the optimized conditions, the detection limit (LOD) was obviously lowered to 70 pg/g (vs. previous 150 pg/g) with R2 > 0.999; the relative standard deviations (RSD) of repeated measurements for real chocolate samples ranged from 1.5% to 6.4%, indicating a favorable precision; and the Cd recoveries were in the range of 93−107%, proving a satisfied accuracy. Thus, the total analysis time is less than 3 min without the sample digestion process. Thereafter, 78 chocolate samples with different brands from 9 producing countries in China market were collected and measured by this proposed method. Based on the measured Cd concentrations, a dietary exposure assessment was performed for Chinese residents, and the target hazard quotient (THQ) values are all less than 1, proving no significant health risk from intaking chocolate cadmium for Chinese residents.

Optimized Box-Behnken Design Combined Response Surface Methodology to Determine Calcium and Iron Contents Using Visible, Atomic Emission and Atomic Absorption Spectrophotometry in Vegetables and Wastewater Samples.

BACKGROUND: Calcium and iron are crucial essential minerals. Iron is mainly responsible for transporting oxygen in the body and the immune system. In comparison, calcium's primary function is in human bones and teeth. Due to that, it is vital to quantify the amount in vegetables. OBJECTIVE: Optimization and validation of three analytical procedures, visible, atomic emission spectrophotometry (AES), and atomic absorption spectrophotometry (AAS), were developed to determine calcium and iron in vegetables and wastewater samples using response surface methodology (RSM) via Box-Behnken design (BBD). The design helps to reduce experiment trials with selected variables to find a correlation between them and their respective dependent variables. METHODS: Method I was developed to quantify calcium in vegetables mixed with concentrated 3M HNO3 and heated to reflux as per the BBD. Then it was cooled, filtered, and completed with 3M HNO3 to be carried out utilizing AES and AAS. For method II, vegetables were mixed with nitric acid and sulfuric acid solution with an optimized 5M KSCN solution, which was computed using the AAS and visible spectrophotometry. RESULTS: First, percentage of water content was calculated for all vegetables, higher in malabar spinach and lower in peas. The calcium and iron contents were present within 0.59-2.68 mg and 35.8-211.5 mg, respectively, in 100 g of vegetables. The results showed a higher amount of iron was available in spinach and a lower amount in okra. In contrast, the highest calcium amount was present in broccoli and the lowest amount was in peas. The calcium and iron content were between 0.015-137.25 and 0.01-147.85 µg/mL in the wastewater samples. CONCLUSIONS: These methods can help to determine the amount of calcium and iron for the quality control samples in research and development, food, and the environmental industry. HIGHLIGHTS: Three validated analytical techniques quantify calcium and iron in vegetables and wastewater samples. The RSM-BBD optimized the method and determined its crucial factors.

A highly selective bulk optode based on 6-{4-(2,4-dihydroxy-phenyl)diazenyl)phenyl}-2-oxo-4-phenyl-1,2-dihydro-pyridine-3-carbonitrile incorporating chromoionophore V for determination of nano levels of cadmium.

A novel optical sensor has been fabricated for highly accurate, simple and selective determination of nanomolar levels of cadmium ions. The sensor depends on the interaction of 6-{4-(2,4-dihydroxyphenyl)diazenyl)phenyl}-2-oxo-4-phenyl-1,2-dihydropyri-dine-3-carbonitrile (DDPODC) with Cd(II) in plasticized (2-nitrophenyloctyl ether) (o-NPOE) polyvinylchloride (PVC) membrane incorporating chromoionophore V as a lipophilic H+-selective indicator. It would seem that the higher Cd(II) concentration, the lower absorbance of chromoionophore V in the membrane at 668 nm, whereas the absorbance at 586 nm increased. The developed sensor at pH 4.7 has a linear range of 5.0 × 10-12 - 2.5 × 10-5 M with limits of detection and quantification of 1.62 × 10-12 and 4.95 × 10-12 M, respectively. The relative standard deviation (RSD) for eight determination of 1.0 × 10-7 M Cd(II) was 1.67%. Finally, the proposed sensor gives good results for applications in the direct determination of cadmium ions in water, food, and biological samples. Additionally, we compared the obtained results with the data obtained from the flame atomic absorption spectrometry (FAAS).

Bismuth fire assay preconcentration and empirical coefficient LA-ICP-MS for the determination of ultra-trace Pt and Pd in geochemical samples.

In this work, a novel method of solid sample pretreatment technique of bismuth fire assay (Bi-FA) combined with solid sample determination by laser ablation ICP-MS (LA-ICP-MS) was reported for the determination of ultra-trace Pt and Pd in geochemical samples. Bismuth oxide (Bi2O3) was used as fire assay collector to directly enrich Pt and Pd from solid samples, and Ag protection cupellation was employed to generate Ag granules. After cleaning, weighing and annealing, the Ag granules were compressed into thin slices and determined by LA-ICP-MS for 195Pt, 105Pd and 109Ag (109Ag was selected as the internal standard isotope). Bi2O3 provided exceptionally low blanks compared to nickel oxide and lead oxide commonly employed in fire assay procedures, and could be applied directly without purification. Different from traditional empirical coefficient method, the Chinese Certified Reference Materials (CRMs) for Pt and Pd were treated by the same procedure to obtain completely matrix matched Ag slices. And then modified empirical coefficient method and internal standard calibration strategy was used to reduce the instability of LA-ICP-MS, and random multipoint laser ablation was employed to further reduce analytical variation resulting from heterogeneity of Pt and Pd in the Ag slice. Under optimal conditions, excellent calibration curves for Pt and Pd were obtained (0.407-2958 µg g-1 and 0.407-2636 µg g-1, respectively), with correlation coefficients exceeding 0.9996. The method detection limits for Pt and Pd were 0.074 and 0.037 ng g-1, respectively. The established method was applied successfully to analysis of real geochemical samples, with determined values in good agreement with the results of traditional Pb-FA graphite furnace atomic absorption spectrometry (GF-AAS), and spiked recoveries between 87.8 and 125.0%.

Development of copper nanoflowers based dispersive solid-phase extraction method for cadmium determination in shalgam juice samples using slotted quartz tube atomic absorption spectrometry.

In this work, dispersive solid-phase extraction procedure was developed for trace cadmium determination before flame atomic absorption spectrometry (FAAS) measurement. Copper(II) based nanoflowers were synthesized to utilize as adsorbent for preconcentration of cadmium. The detection power of the spectrometric system was enhanced by placing a slotted quartz tube (SQT) onto the flame burner which increases the residence time of the analyte atoms in the flame region. The analytical performance of the developed system was evaluated with and without SQT equipment and the enhancement in detection power was calculated by the ratio of detection limits of CuNF-DSPE-FAAS (copper nanoflower based dispersive solid phase extraction-flame atomic absorption spectrometry) and FAAS system. Enhancement was determined as 73 and 104.3 times for CuNF-DSPE-FAAS and CuNF-DSPE-SQT-FAAS (CuNF-DSPE-slotted quartz tube-FAAS), respectively. Percent recovery results indicated the applicability of the developed method for the determination of trace cadmium.

Vortex-assisted restricted access-based supramolecular solvent microextraction of trace Pb(II) ions with 4-(benzimidazolisonitrosoacetyl)biphenyl as a complexing agent before microsampling flame AAS analysis.

A new oxime compound, 4-(benzimidazolisonitrosoacetyl)biphenyl (BIBP) was synthesized and used as a complexing agent in this study to preconcentrate trace amounts of Pb(II) ions with vortex-assisted restricted access-based supramolecular solvent microextraction (RA/SUPRAS-LPME) method. The new complexing agent was characterized by a combination of elemental analyses, Proton Nuclear Magnetic Resonance (1H- NMR), Carbon-13 Nuclear Magnetic Resonance (13C NMR) and Fourier Transform Infrared spectroscopy (FT-IR) and techniques. Extraction of the complex which was formed at pH 8.0 was done by using a supramolecular solvent phase of tetrahydrofuran (THF) and 1-decanol. A microsampling flame atomic absorption spectrophotometer was used to measure the lead ion concentrations of the extract. The method optimized and the optimum experimental conditions were found as; pH = 8, amount of the ligand 2,25 mg, supramolecular solvent volume 50 µL, sample volume 20 mL and vortex time 3 min. The limit of detection (LOD), limit of quantification (LOQ) were calculated as 0.69 µg L-1 and 2.29 µg L-1, respectively. Linear range was found between 15.1 µg L-1 and 606 µg L-1. The developed method was applied to Pb(II) determination in real samples after evaluating the accuracy by using the TMDA-53.3 fortified environmental water sample as certified reference material.

Fabrication and Characterizations of Axial View Liquid Electrode Plasma Atomic Emission Spectrometry for the Sensitive Determination of Trace Zinc, Cadmium, and Lead.

Axial view liquid electrode plasma-atomic emission spectrometry (axial view LEP-AES) was proposed and fabricated successfully in this work. The emission spectra from Zn, Cd, Pb, Ca, and K were applied for characterization and optimization. Comparing with conventional radial view LEP-AES devices, the newly designed axial view-LEP provided better sensing ability toward trace heavy metals. Moreover, pulsed voltage discharge was found to be advantageous over continuous discharge under the same discharge time for detection. The optimized parameters facilitate the limit of detection to achieve 0.24, 0.051, and 0.85 µg L-1 for Zn, Cd, and Pb, respectively. Furthermore, the axial view LEP-AES possessed excellent reproducibility and good durability. The real sample tests using two different certified reference water samples revealed the great potential of the axial view LEP-AES as a novel practical elemental analysis tool.