Assessment of image quality in digital radiology using the CDRAD contrast-detail phantom in pediatrics / Evaluación de la calidad de la imagen en radiología digital utilizando el fantoma de detalle de contraste CDRAD en pediatría

ABSTRACT The transition from analog to digital radiology has expanded the capabilities of radiological imaging but has also made it possible to increase the radiation dose received by patients. Image quality in radiology is determined by factors such as radiographic techniques (kVp and mAs), which directly impact the dose and image quality. This study focuses on pediatric radiological exams considering their greater radiosensitivity and longer life expectancy. The study aimed to investigate the correlation between image quality and applied radiographic techniques using the CDRAD contrast-detail phantom. The results showed a direct linear relationship between the increase in kVp and the corresponding increase in image quality. Nonetheless, there was a significant variation in image quality between current-time products ranging from 0.5 to 2.5 mAs, in contrast to the nearly linear relationship observed within the 2.5 and 10 mAs range

RESUMEN La transición de la radiología analógica a la digital ha ampliado las capacidades de las imágenes radiológicas, pero ha también permitió aumentar la dosis de radiación que reciben los pacientes. La calidad de la imagen en radiología está determinada por factores como las técnicas radiográficas (kVp y mAs), que impactan directamente en la dosis y la calidad de la imagen. Este estudio se centra en exámenes radiológicos pediátricos considerando su mayor radiosensibilidad y mayor espe ranza de vida. El estudio está dirigido a investigar la correlación entre la calidad de la imagen y las técnicas radiográficas aplicadas utilizando el detalle de contraste CDRAD fantasma. Los resultados mostraron una relación lineal directa entre el aumento de kVp y el correspondiente aumento de calidad de la imagen. No obstante, hubo una variación significativa en la calidad de la imagen entre los productos actuales que van desde 0,5 a 2,5 mAs, en contraste con la relación casi lineal observada dentro del rango de 2,5 y 10 mAs.

An audit of the polytrauma fracture detection rate of clinicians evaluating lodox statscan bodygrams in two South African public sector trauma units.

BACKGROUND: Increasing global demand for specialized radiological investigations has resulted in delayed or non-reporting of plain trauma radiographs by radiologists. This is particularly true in resource-limited environments, where referring clinicians rely largely on their own radiographic interpretation. A wide accuracy range has been documented for non-radiologist reporting of conventional trauma radiographs. The Lodox Statscan whole-body digital X-ray machine is a relatively new technology that poses unique interpretive challenges. The fracture detection rate of trauma clinicians utilizing this modality has not been determined. OBJECTIVE: An audit of the polytrauma fracture detection rate of clinicians evaluating Lodox Statscan bodygrams in two South African public-sector Trauma Units. METHODS: A retrospective descriptive study of imaging data of Cape Town Level 1-equivalent public-sector Trauma Units during March-April 2015. Statscan bodygrams acquired for adult polytrauma triage were reviewed and correlated with follow-up imaging and patient records. Missed fractures were stratified by body part, mechanism of injury and ventilatory support. The fracture detection rate was determined with 95% confidence. The Generalised Fischer Exact Test assessed any association between the fracture site and failure of detection. Specialist orthopaedic review assessed the potential need for surgical management of missed fractures. RESULTS: 227 patients (male = 193, 85%; mean age: 33 years) were included; 195 fractures were demonstrated on the whole-body triage projections. Lower limb fractures predominated (n = 66, 34%). The fracture detection rate was 89% (95% CI = 86-93%), with the site of fracture associated with failure of detection (p = 0.01). Twelve of 21 undetected fractures (57%) involved the elbow or shoulder girdle. All elbow fractures (n = 3, 100%), more than half the shoulder girdle fractures (9/13,69%) and 12% (15/123) of extremity fractures were undetected. One missed fracture (1/21,4.7%) unequivocally required surgical management, while a further 7 (7/21, 33.3%) could potentially have benefitted from surgery, depending on follow-up imaging findings. CONCLUSION: This is the first analysis of the accuracy of bodygram polytrauma fracture detection by clinicians. Particular review of the shoulder girdle, elbow and extremities for subtle fractures, in addition to standardized limb positioning, are recommended for improved diagnostic accuracy in this setting. These findings can inform clinician training courses in this domain.

Radiosynthesis and modified quality control of O-(2-[18F]fluoroethyl)-L-tyrosine ([18F]FET) for brain tumor imaging.

O-(2-[18F]fluoroethyl)-L-tyrosine ([18F]FET) is the most promising radio-labeled amino acid tracer for brain tumor imaging due to the limitation of 2-deoxy-2-[18F]fluoro-D-glucose ([18F]FDG) and L-methyl-[11C]methionine (11C-MET). However, it has some limitations in radiosynthesis and related quality control that make it less frequently used in many PET centers, in this study, we report a new modification of [18F]FET production using a commercially available fully automated GRP SCINTOMICS module overcoming some of the existing limitations along with a suggestion of a simplified quality control procedure with special focus placed on enantiomeric and radiochemical purity. ([18F]FET) was produced in high radiochemical and enantiomeric purity more than 99% and non-decay corrected yield 25±5% in about 55min.

Basic Study on Visibility and Water Equivalency of a New Colorless Transparent Bolus for Electron Radiotherapy.

Boluses used in electron radiotherapy need to have radiation field visibility and water equivalence. In this report, we have examined field visibility and water equivalence of a new colorless transparent bolus. We examined field visibility, water equivalence, and dose profile. Field visibility was evaluated by comparison to conventional bolus. Water equivalence was investigated by a measured fluence scaling factor. The dose profile was measured by using radiochromic film with the bolus and an ionization chamber in water. We confirmed that the irradiation field could clearly be seen through the transparent colorless bolus. The bolus did not cast a field edge as compared with the conventional bolus. The fluence scaling factor was less than 0.8% as compared to water. We confirmed that the colorless transparent bolus was treated as a water equivalent material. The percentage depth dose (PDD) measured by using radiochromic film with the bolus matched the PDD measured with an ionization chamber in water. R50 was less than 1 mm as compared to PDD measured with an ionization chamber. It was confirmed that the colorless transparent bolus can use to set up patient without losing visibility on flat ground planes. The fluence scaling factor and dose profile measured by using the bolus matched the results measured in water. Therefore, the new colorless transparent bolus has feasibility to improve patient setup efficiency and can improve calculation accuracy by using the fluence scaling factor.

Medical Devices; Radiology Devices; Classification of the Rectal Balloon for Prostate Immobilization. Final order.

The Food and Drug Administration (FDA or we) is classifying the rectal balloon for prostate immobilization into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the rectal balloon for prostate immobilization's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

Adverse Events Involving Radiation Oncology Medical Devices: Comprehensive Analysis of US Food and Drug Administration Data, 1991 to 2015.

PURPOSE: Radiation oncology relies on rapidly evolving technology and highly complex processes. The US Food and Drug Administration collects reports of adverse events related to medical devices. We sought to characterize all events involving radiation oncology devices (RODs) from the US Food and Drug Administration's postmarket surveillance Manufacturer and User Facility Device Experience (MAUDE) database, comparing these with non-radiation oncology devices. METHODS AND MATERIALS: MAUDE data on RODs from 1991 to 2015 were sorted into 4 product categories (external beam, brachytherapy, planning systems, and simulation systems) and 5 device problem categories (software, mechanical, electrical, user error, and dose delivery impact). Outcomes included whether the device was evaluated by the manufacturer, adverse event type, remedial action, problem code, device age, and time since 510(k) approval. Descriptive statistics were performed with linear regression of time-series data. Results for RODs were compared with those for other devices by the Pearson χ2 test for categorical data and 2-sample Kolmogorov-Smirnov test for distributions. RESULTS: There were 4234 ROD and 4,985,698 other device adverse event reports. Adverse event reports increased over time, and events involving RODs peaked in 2011. Most ROD reports involved external beam therapy (50.8%), followed by brachytherapy (24.9%) and treatment planning systems (21.6%). The top problem types were software (30.4%), mechanical (20.9%), and user error (20.4%). RODs differed significantly from other devices in each outcome (P<.001). RODs were more likely to be evaluated by the manufacturer after an event (46.9% vs 33.0%) but less likely to be recalled (10.5% vs 37.9%) (P<.001). Device age and time since 510(k) approval were shorter among RODs (P<.001). CONCLUSIONS: Compared with other devices, RODs may experience adverse events sooner after manufacture and market approval. Close postmarket surveillance, improved software design, and manufacturer-user training may help mitigate these events.

Lu-177 preparation for radiotherapy application.

A separation study using a (176)Yb target for the preparation of nca (177)Lu, which is a beta-emitting nuclide used not only in radioimmunotherapy applications but also in the treatment of various lesions, has been performed. A material having a better selectivity and separation efficiency for Lu than Yb was developed, and the separation conditions of (177)Lu were derived using this from a neutron irradiated (176)Yb target. The separation material was an organo-ceramic hybrid material containing a phosphate group. Adsorption behavior was determined through batch experiments, and (177)Lu separation from the Yb target was evaluated through column experiments. The Yb target, with a 99.72% in (176)Yb, was irradiated in the irradiation hole of HANARO, which has a thermal neutron flux of 1.6E+14ncm(-2)s(-1). The batch experiments revealed that the organo-ceramic hybrid material (Sol-POS) had a separation factor of 1.6 at 0.5M HCl. Separation was performed through extraction chromatography using a 5mg enriched Yb target, and the separation yield of the NCA (177)Lu was about 78%. If the amount of Yb target is increased to produce curies level (177)Lu, additional purification will be needed.

DOSE TO RADIOLOGICAL TECHNOLOGISTS FROM INDUCED RADIONUCLIDES IN CARBON ION RADIOTHERAPY.

Radioactive nuclides are induced in irradiation devices and patients during high-energy photon and ion beam radiotherapies. These nuclides potentially become sources of exposure to radiation workers. Radiological technologists (RTs) are often required to enter an irradiation room and approach activated devices and patients. In this study, annual doses to RTs working in a carbon ion radiotherapy facility were estimated based on measurements with the Si-semiconductor personal dosemeter. In addition, the time decay of dose around a patient couch after irradiation was obtained by phantom experiments. The annual Hp(10) values for passive and scanned beams were estimated to be 61 and 2 µSv, respectively, when assuming the number of treatments in 2013. These are much lower than the ICRP recommended dose limit for radiation workers. The time-series data of dose to RTs during their work and the time decay of the dose should be helpful for reducing their dose further.

Automated synthesis of [(18)F](2S,4R)-4-fluoroglutamine on a GE TRACERlab™ FX-N Pro module.

Glutamine (Gln) and its analogues may serve as imaging agents for tumor diagnosis using positron emission tomography (PET), especially for tumors with negative [(18)F]FDG scan. We report the first automated synthesis of [(18)F](2S,4R)-4-fluoroglutamine ([(18)F]FGln) on a GE TRACERlab™ FX-N Pro module. [(18)F]FGln was obtained in 80±3min with a radiochemical yield of 21±3% (n=5, uncorrected). The radiochemical purity was >98%, and optical purity 90±5%. The synthesis is highly reproducible with good chemical purity, radiochemical yield, and is suitable for translation to cGMP production.

Beam's-eye-view dosimetrics (BEVD) guided rotational station parameter optimized radiation therapy (SPORT) planning based on reweighted total-variation minimization.

Conventional VMAT optimizes aperture shapes and weights at uniformly sampled stations, which is a generalization of the concept of a control point. Recently, rotational station parameter optimized radiation therapy (SPORT) has been proposed to improve the plan quality by inserting beams to the regions that demand additional intensity modulations, thus formulating nonuniform beam sampling. This work presents a new rotational SPORT planning strategy based on reweighted total-variation (TV) minimization (min.), using beam's-eye-view dosimetrics (BEVD) guided beam selection. The convex programming based reweighted TV min. assures the simplified fluence-map, which facilitates single-aperture selection at each station for single-arc delivery. For the rotational arc treatment planning and non-uniform beam angle setting, the mathematical model needs to be modified by additional penalty term describing the fluence-map similarity and by determination of appropriate angular weighting factors. The proposed algorithm with additional penalty term is capable of achieving more efficient and deliverable plans adaptive to the conventional VMAT and SPORT planning schemes by reducing the dose delivery time about 5 to 10 s in three clinical cases (one prostate and two head-and-neck (HN) cases with a single and multiple targets). The BEVD guided beam selection provides effective and yet easy calculating methodology to select angles for denser, non-uniform angular sampling in SPORT planning. Our BEVD guided SPORT treatment schemes improve the dose sparing to femoral heads in the prostate and brainstem, parotid glands and oral cavity in the two HN cases, where the mean dose reduction of those organs ranges from 0.5 to 2.5 Gy. Also, it increases the conformation number assessing the dose conformity to the target from 0.84, 0.75 and 0.74 to 0.86, 0.79 and 0.80 in the prostate and two HN cases, while preserving the delivery efficiency, relative to conventional single-arc VMAT plans.

Analysis of licensed South African diagnostic imaging equipment.

INTRODUCTION OBJECTIVE: To conduct an analysis of all registered South Africa (SA) diagnostic radiology equipment, assess the number of equipment units per capita by imaging modality, and compare SA figures with published international data, in preparation for the introduction of national health insurance (NHI) in SA. METHODS: The SA Radiation Control Board's database of registered diagnostic radiology equipment was analysed by modality, province and healthcare sector. Access to services was reflected as number of units/million population, and compared with published international data. RESULTS: General X-ray units are the most equitably distributed and accessible resource (34.8/million). For fluoroscopy (6.6/million), mammography (4.96/million), computed tomography (5.0/million) and magnetic resonance imaging (2.9/million), there are at least 10-fold discrepancies between the least and best resourced provinces. Although SA's overall imaging capacity is well above that of other countries in sub-Saharan Africa, it is lower than that of all Organisation for Economic Co-operation and Development (OECD). While SA's radiological resources most closely approximate those of the United Kingdom, they are substantially lower than the UK. CONCLUSION: SA access to radiological services is lower than that of any OECD country. For the NHI to achieve equitable access to diagnostic imaging for all citizens, SA will need a more homogeneous distribution of specialised radiological resources and customized imaging guidelines.

Review on the characteristics of radiation detectors for dosimetry and imaging.

The enormous advances in the understanding of human anatomy, physiology and pathology in recent decades have led to ever-improving methods of disease prevention, diagnosis and treatment. Many of these achievements have been enabled, at least in part, by advances in ionizing radiation detectors. Radiology has been transformed by the implementation of multi-slice CT and digital x-ray imaging systems, with silver halide films now largely obsolete for many applications. Nuclear medicine has benefited from more sensitive, faster and higher-resolution detectors delivering ever-higher SPECT and PET image quality. PET/MR systems have been enabled by the development of gamma ray detectors that can operate in high magnetic fields. These huge advances in imaging have enabled equally impressive steps forward in radiotherapy delivery accuracy, with 4DCT, PET and MRI routinely used in treatment planning and online image guidance provided by cone-beam CT. The challenge of ensuring safe, accurate and precise delivery of highly complex radiation fields has also both driven and benefited from advances in radiation detectors. Detector systems have been developed for the measurement of electron, intensity-modulated and modulated arc x-ray, proton and ion beams, and around brachytherapy sources based on a very wide range of technologies. The types of measurement performed are equally wide, encompassing commissioning and quality assurance, reference dosimetry, in vivo dosimetry and personal and environmental monitoring. In this article, we briefly introduce the general physical characteristics and properties that are commonly used to describe the behaviour and performance of both discrete and imaging detectors. The physical principles of operation of calorimeters; ionization and charge detectors; semiconductor, luminescent, scintillating and chemical detectors; and radiochromic and radiographic films are then reviewed and their principle applications discussed. Finally, a general discussion of the application of detectors for x-ray nuclear medicine and ion beam imaging and dosimetry is presented.

Pre-clinical research in small animals using radiotherapy technology--a bidirectional translational approach.

For translational cancer research, pre-clinical in-vivo studies using small animals have become indispensable in bridging the gap between in-vitro cell experiments and clinical implementation. When setting up such small animal experiments, various biological, technical and methodical aspects have to be considered. In this work we present a comprehensive topical review based on relevant publications on irradiation techniques used for pre-clinical cancer research in mice and rats. Clinical radiotherapy treatment devices for the application of external beam radiotherapy and brachytherapy as well as dedicated research irradiation devices are feasible for small animal irradiation depending on the animal model and the experimental goals. In this work, appropriate solutions for the technological transfer of human radiation oncology to small animal radiation research are summarised. Additionally, important information concerning the experimental design is provided such that reliable and clinically relevant results can be attained.

Intraoral radiology in general dental practices - a comparison of digital and film-based X-ray systems with regard to radiation protection and dose reduction.

PURPOSE: The purpose of this study was to gain insight into the distribution and application of digital intraoral radiographic techniques within general dental practices and to compare these with film-based systems in terms of patient dose reduction. MATERIALS AND METHODS: 1100 questionnaires were handed out to general dental practitioners. Data was analyzed with respect to the type of system by using descriptive statistics and nonparametric tests, i.e. Kruskal-Wallis, Mann-Whitney and chi-square test (SPSS 20). RESULTS: 64% of the questioned dentists still use film-based radiology, 23% utilize storage phosphor plate (SPP) systems and 13% use a charge-coupled device (CCD). A strong correlation between the number of dentists working in a practice and the use of digital dental imaging was observed. Almost 3/4 of the film users work with E- or F-speed film. 45% of them refuse to change to a digital system. The use of lead aprons was popular, while only a minority preferred thyroid shields and rectangular collimators. A fourfold reduction of exposure time from D-speed film to CCD systems was observed. Due to detector size and positioning errors, users of CCD systems take significantly more single-tooth radiographs in total. Considering the number of radiographs per patient, there is only a slight tendency towards more X-rays with CCD systems. Up to image generation, digital systems seem to be as or even more difficult to handle than film-based systems, while their handling was favored after radiographic exposure. CONCLUSION: Despite a slight increase of radiographs taken with CCD systems, there is a significant dosage reduction. Corresponding to the decrease in exposure time, the patient dose for SPP systems is reduced to one half compared to film. The main issues in CCD technology are positioning errors and the size of the X-ray detectors which are difficult to eliminate. The usage of radiation protection measures still needs to be improved. KEY POINTS: ► Responsible use of digital intraoral radiology results in a significant dose reduction in everyday practice. ► The ALARA principle is only achieved by strict implementation of dose-reducing methods. ► The efforts to use dose-reducing devices must be increased.