Modulation of human mesenchymal stem cell behavior on ordered tantalum nanotopographies fabricated using colloidal lithography and glancing angle deposition.

Ordered surface nanostructures have attracted much attention in biotechnology and biomedical engineering because of their potential to modulate cell-surface interactions in a controllable manner. However, the ability to fabricate large area ordered nanostructures is limited because of high costs and low speed of fabrication. Here, we have fabricated ordered nanostructures with large surface areas (1.5 × 1.5 cm(2)) using a combination of facile techniques including colloidal self-assembly, colloidal lithography and glancing angle deposition (GLAD). Polystyrene (722 nm) colloids were self-assembled into a hexagonally close-packed (hcp) crystal array at the water-air interface, transferred on a biocompatible tantalum (Ta) surface and used as a mask to generate an ordered Ta pattern. The Ta was deposited by sputter coating through the crystal mask creating approximately 60-nm-high feature sizes. The feature size was further increased by approximately 200-nm-height respectively using GLAD, resulting in the fabrication of four different surfaces (FLAT, Ta60, GLAD100, and GLAD200). Cell adhesion, proliferation, and osteogenic differentiation of primary human adipose-derived stem cells (hADSCs) were studied on these ordered nanostructures for up to 2 weeks. Our results suggested that cell spreading, focal adhesion formation, and filopodia extension of hADSCs were inhibited on the GLAD surfaces, while the growth rate was similar between each surface. Immunostaining for type I collagen (COL1) and osteocalcin (OC) showed that there was higher osteogenic components deposited on the GLAD surfaces compared to the Ta60 and FLAT surfaces after 1 week of osteogenic culture. After 2 weeks of osteogenic culture, alkaline phosphatase (ALP) activity and the amount of calcium was higher on the GLAD surfaces. In addition, osteoblast-like cells were confluent on Ta60 and FLAT surfaces, whereas the GLAD surfaces were not fully covered suggesting that the cell-cell interactions are stronger than cell-substrate interactions on GLAD surfaces. Visible extracellular matrix deposits decorated the porous surface can be found on the GLAD surfaces. Depth profiling of surface components using a new Ar cluster source and X-ray photoelectron spectroscopy (XPS) showed that deposited extracellular matrix on GLAD surfaces is rich in nitrogen. The fabricated ordered surface nanotopographies have potential to be applied in diverse fields, and demonstrate that the behavior of human stem cells can be directed on these ordered nanotopographies, providing new knowledge for applications in biomaterials and tissue engineering.

A novel star PEG-derived surface coating for specific cell adhesion.

In this study a novel approach for the coating and functionalization of substrates for cell culture and tissue engineering is presented. Glass, silicon, and titanium panes were coated with an ultrathin film (30 +/- 5 nm) of reactive star-shaped poly(ethylene glycol) prepolymers (Star PEG). Homogeneity of the films was checked by optical microscopy and scanning force microscopy. These coatings prevent unspecific protein adsorption as monitored by fluorescence microscopy and ellipsometry. In order to allow specific cell adhesion the films were modified with linear RGD peptides (gRGDsc) in different concentrations. After sterilization, fibroblast, SaOS, and human mesenchymal stem cells (hMSC) were seeded on these substrates. Cell adhesion, spreading, and survival was observed for up to 30 days on linear RGD peptide (gRGDsc)-modified coatings, whereas no cell adhesion could be detected on unmodified Star PEG layers. By variation of the RGD concentration within the film the amount of cells that became adhesive could be controlled. When differentiation conditions are used for cultivation of hMSCs the cells show the expression of osteogenic marker genes after 14 days which is comparable to cultivation on cell culture plastic. Thus, the Star PEG/RGD film did not negatively influence the differentiation process. The high flexibility of the system considering the incorporation of biologically active compounds opens a broad field of future experiments.

Biofunctionalized, ultrathin coatings of cross-linked star-shaped poly(ethylene oxide) allow reversible folding of immobilized proteins.

Dense, ultrathin networks of isocyanate terminated star-shaped poly(ethylene oxide) (PEO) molecules, cross-linked at their chain ends via urea groups, were shown to be extremely resistant to unspecific adsorption of proteins while at the same time suitable for easy biocompatible modification. Application by spin coating offers a simple procedure for the preparation of minimally interacting surfaces that are functionalized by suitable linker groups to immobilize proteins in their native conformations. These coatings form a versatile basis for biofunctional and biomimetic surfaces. We have demonstrated their advantageous properties by using single-molecule fluorescence microscopy to study immobilized proteins under destabilizing conditions. Biotinylated ribonuclease H (RNase H) was labeled with a fluorescence resonance energy transfer (FRET) pair of fluorescent dyes and attached to the surface by a biotin-streptavidin linkage. FRET analysis demonstrated completely reversible denaturation/renaturation behavior upon exposure of the surface-immobilized proteins to 6 M guanidinium chloride (GdmCl) followed by washing in buffer. A comparison with bovine serum albumin (BSA) coated surfaces and linear PEO brush surfaces yielded superior performance in terms of chemical stability, inertness and noninteracting nature of the star-polymer derived films.