Synthesis of iron and copper cluster-grafted zinc oxide nanorod with enhanced visible-light-induced photocatalytic activity.

Design of visible-light-responsive photocatalyst employing simple and cost-effective method is of great importance from commercial point of view. Herein, we report the synthesis of visible-light-sensitive ubiquitous nanoclusters of Fe3+/Cu2+-grafted ZnO nanorod using impregnation technique, which showed excellent photocatalytic activity towards the decomposition of Rhodamine B (RhB), 4-nitrophenol (4-NP) and paracetamol in aqueous suspension under atmospheric oxygen. Fe-grafted ZnO nanorod exhibited pronounced effect for the degradation of the above-mentioned pollutants compared to pure ZnO and Cu-grafted ZnO nanorod. The better activity could be due to the more positive redox potential of surface grafted Fe3+ species resulting in the generation of more hydroxyl radicals thereby, leading to higher photodegradation rate.

Revelation of Different Nanoparticle-Uptake Behavior in Two Standard Cell Lines NIH/3T3 and A549 by Flow Cytometry and Time-Lapse Imaging.

The uptake of nanomaterials into different cell types is a central pharmacological issue for the determination of nanotoxicity as well as for the development of drug delivery strategies. Most responses of the cells depend on their intracellular interactions with nanoparticles (NPs). Uptake behavior can be precisely investigated in vitro, with sensitive high throughput methods such as flow cytometry. In this study, we investigated two different standard cell lines, human lung carcinoma (A549) and mouse fibroblast (NIH/3T3) cells, regarding their uptake behavior of titanium dioxide NPs. Cells were incubated with different concentrations of TiO2 NPs and samples were taken at certain time points to compare the uptake kinetics of both cell lines. Samples were analyzed with the help of flow cytometry by studying changes in the side and forward scattering signal. To additionally enable a detection via fluorescence, NPs were labeled with the fluorescent dye fluorescein isothiocyanate (FITC) and propidium iodide (PI). We found that NIH/3T3 cells take up the studied NPs more efficiently than A549 cells. These findings were supported by time-lapse microscopic imaging of the cells incubated with TiO2 NPs. Our results confirm that the uptake behavior of individual cell types has to be considered before interpreting any results of nanomaterial studies.

Multifunctional Gadolinium-Doped Mesoporous TiO2 Nanobeads: Photoluminescence, Enhanced Spin Relaxation, and Reactive Oxygen Species Photogeneration, Beneficial for Cancer Diagnosis and Treatment.

Materials with controllable multifunctional abilities for optical imaging (OI) and magnetic resonant imaging (MRI) that also can be used in photodynamic therapy are very interesting for future applications. Mesoporous TiO2 sub-micrometer particles are doped with gadolinium to improve photoluminescence functionality and spin relaxation for MRI, with the added benefit of enhanced generation of reactive oxygen species (ROS). The Gd-doped TiO2 exhibits red emission at 637 nm that is beneficial for OI and significantly improves MRI relaxation times, with a beneficial decrease in spin-lattice and spin-spin relaxation times. Density functional theory calculations show that Gd3+ ions introduce impurity energy levels inside the bandgap of anatase TiO2 , and also create dipoles that are beneficial for charge separation and decreased electron-hole recombination in the doped lattice. The Gd-doped TiO2 nanobeads (NBs) show enhanced ability for ROS monitored via • OH radical photogeneration, in comparison with undoped TiO2 nanobeads and TiO2 P25, for Gd-doping up to 10%. Cellular internalization and biocompatibility of TiO2 @xGd NBs are tested in vitro on MG-63 human osteosarcoma cells, showing full biocompatibility. After photoactivation of the particles, anticancer trace by means of ROS photogeneration is observed just after 3 min irradiation.

Three dimensional spheroid cell culture for nanoparticle safety testing.

Nanoparticles are widely employed for many applications and the number of consumer products, incorporating nanotechnology, is constantly increasing. A novel area of nanotechnology is the application in medical implants. The widespread use of nanoparticles leads to their higher prevalence in our environment. This, in turn, raises concerns regarding potential risks to humans. Previous studies have shown possible hazardous effects of some nanoparticles on mammalian cells grown in two-dimensional (2D) cultures. However, 2D in vitro cell cultures display several disadvantages such as changes in cell shape, cell function, cell responses and lack of cell-cell contacts. For this reason, the development of better models for mimicking in vivo conditions is essential. In the present work, we cultivated A549 cells and NIH-3T3 cells in three-dimensional (3D) spheroids and investigated the effects of zinc oxide (ZnO-NP) and titanium dioxide nanoparticles (TiO2-NP). The results were compared to cultivation in 2D monolayer culture. A549 cells in 3D cell culture formed loose aggregates which were more sensitive to the toxicity of ZnO-NP in comparison to cells grown in 2D monolayers. In contrast, NIH-3T3 cells showed a compact 3D spheroid structure and no differences in the sensitivity of the NIH-3T3 cells to ZnO-NP were observed between 2D and 3D cultures. TiO2-NP were non-toxic in 2D cultures but affected cell-cell interaction during 3D spheroid formation of A549 and NIH-3T3 cells. When TiO2-NP were directly added during spheroid formation in the cultures of the two cell lines tested, several smaller spheroids were formed instead of a single spheroid. This effect was not observed if the nanoparticles were added after spheroid formation. In this case, a slight decrease in cell viability was determined only for A549 3D spheroids. The obtained results demonstrate the importance of 3D cell culture studies for nanoparticle safety testing, since some effects cannot be revealed in 2D cell culture.

Influence of inlet concentration and light intensity on the photocatalytic oxidation of nitrogen(II) oxide at the surface of Aeroxide® TiO2 P25.

Air pollution by nitrogen oxides represents a serious environmental problem in urban areas where numerous sources of these pollutants are concentrated. One approach to reduce the concentration of these air pollutants is the light-induced oxidation in the presence of molecular oxygen and a photocatalytically active building material, e.g., paints, roof tiles, or pavement stones. Herein, results of an investigation concerning the photocatalytic oxidation of nitrogen(II) oxide (NO) in the presence of molecular oxygen and UV(A) irradiated TiO(2) powder are presented. The standard operating procedure described in ISO 22197-1 which was developed to characterize the photocatalytic activity of air-cleaning products was successfully applied to determine the photocatalytic activity of a bare TiO(2) powder. The experimental data reveal that at the light intensity stipulated by the operation procedure the amount of NO removed from the gas phase by photocatalytic oxidation is strongly affected by small changes of this light intensity as well as of the NO concentration in the gas stream in the photoreactor. Therefore, these parameters have to be controlled very carefully. Based upon the experimental data obtained in this study a rate law for the photocatalytic NO oxidation inside the photoreactor is derived.

Metal-free porphyrin-sensitized mesoporous titania films for visible-light indoor air oxidation.

Transparent cubic mesoporous TiO2 films coated on soda-lime glass have been developed. A metal free meso-tetrakis(4-sulfonatophenyl) porphyrin (TPPS) has been adsorbed on these TiO2 films from aqueous solutions. The results indicated that the obtained mesoporous TiO2 and 3D TPPS/TiO2 films are optically transparent and crack free (thickness ca. 200±20 nm). The introduction of the TPPS molecules has only a very small influence on the pore system and some limited pore blocking seems to occur. Transmission electron microscopy (TEM) images revealed that the adsorption of TPPS does not disrupt the meso order of TPPS/TiO2. The particle size of these TiO2 nanocrystals has been measured to be approximately 5-8 nm. TPPS/TiO2 photocatalysts, exhibiting regularly ordered mesopores, large surface area (ca. 102.5 cm(2) cm(-2)), and specific pore volume of about 0.1 mm(3) cm(-2), show improved light-harvesting efficiency as compared with other transparent TiO2 films. Employing the 3D TPPS/TiO2 photocatalyst, a quantum efficiency of 0.059 % has been obtained for the photodegradation of CH3CHO in the gas phase under visible-light illumination. Recycling tests demonstrated that the newly synthesized photocatalyst was quite stable during this gas-solid heterogeneous photocatalytic process because no significant decrease in photocatalytic activity was observed even after being used repetitively up to five times. Therefore, the newly synthesized transparent 3D TPPS/TiO2 photocatalysts can potentially be applied for low-cost air purification and self-cleaning applications.

Enhanced photocatalytic production of molecular hydrogen on TiO(2) modified with Pt-polypyrrole nanocomposites.

Titanium dioxide was modified with Pt-polypyrrole nanocomposites through the in situ simultaneous reduction of Pt(iv) and the oxidative polymerization of pyrrole monomers at ambient temperature. The modified powders were characterized using X-ray photoelectron spectroscopy (XPS), dark-field scanning transmission electron microscopy (DF-STEM), infrared spectroscopy (IR) and by the determination of the BET surface area by nitrogen adsorption. Photocatalytic hydrogen production tests were performed employing 75 ml aqueous solution containing 2250 mumol methanol as the sacrificial electron donor. The obtained results show that 0.5 and 1.0 wt% Pt and polypyrrole, respectively, are the optimum ratios for high photocatalytic H(2) production rates. The amount of H(2) evolved during 5 h of UV-vis illumination of the suspension of Pt-polypyrrole modified TiO(2) powder is three times higher than that obtained with Pt-loaded TiO(2) prepared by a photochemical deposition method. The photonic efficiencies of the H(2) production employing 75 ml aqueous solution containing 370 mmol methanol were calculated to be 10.6 +/- 0.5 and 4.5 +/- 0.2% for TiO(2) modified with Pt-polypyrrole nanocomposites and for Pt-loaded TiO(2) prepared by a photochemical deposition method, respectively. A synergistic effect between Pt nanoparticles and polypyrrole leading to a better separation of the charge carriers is proposed to explain the enhanced reactivity of the newly synthesized photocatalyst.

Semiconductor-mediated photocatalysed degradation of two selected priority organic pollutants, benzidine and 1,2-diphenylhydrazine, in aqueous suspension.

The photocatalysed degradation of two selected priority organic pollutants, namely benzidine (1) and 1,2-diphenylhydrazine (DPH, 2) has been investigated in aqueous suspensions of titanium dioxide (TiO2) under a variety of conditions employing a pH-stat technique. The degradation was studied by monitoring the change in substrate concentration of the model compound employing HPLC analysis and the decrease in total organic carbon content, respectively, as a function of irradiation time. The degradation kinetics were studied under different conditions such as reaction pH, substrate and photocatalyst concentration, type of TiO2 photocatalyst and the presence of alternative additives such as H2O2, KBrO3 and (NH4)2S2O8 besides molecular oxygen. The degradation rates and the photonic efficiencies were found to be strongly influenced by the above parameters. Toxicity tests for the irradiated samples of benzidine measuring the luminescence of bacteria Vibrio fischeri after 30 min of incubation were also performed. 4-amino-biphenyl (7) and hydroquinone (13) were identified as intermediate products by GC/MS technique and probable pathways for the formation of the products are proposed.