Influence of aging on bond strength of artificial teeth to denture base acrylic resins

Aim: The aim of this study was to evaluate the bond strength of artificial teeth to different types of denture base resins when submitted to thermomechanical cycling (TMC). Methods: Sixty artificial mandibular first molars (Trilux, Vipi) were randomly divided into 3 groups according to denture base acrylic resins (Vipi Wave, Vipi Cril, and Vipi Cril Plus, Vipi). The teeth were fixed onto self-polymerizing acrylic resin bars (0.5 cm2 cross-section x 2 cm height), and the set was included in a metal flask using dental stone/silicone. After the dental stone was set, the bar was removed, and the denture base resin was packed and processed according to the group studied (Vipi Wave: 180 W/20 minutes + 540W/5 minutes; Vipi Cril and Vipi Cril Plus: Water bath at 74ºC for 9h). After polymerization, the samples were divided into 2 groups (n=10), according to the TMC treatment received (simulation of 5 years of mastication or not). The samples were submitted to tensile bond strength test (1 mm/min), and the data (MPa) were statistically analyzed (2-way ANOVA, Bonferroni, α=0.05). The fracture interfaces were evaluated using a stereomicroscope (50x). Results: The bond strength results showed no statistically significant difference (p>0.05) between the resins studied. TMC was significant (p<0.05), demonstrating lower values for the bond strength of artificial teeth to Vipi Cril Plus. The predominant fracture type was cohesive in resin. Conclusions: It was concluded that there is no difference in bond strength between artificial teeth and the resins used for denture base. However, TMC decreases the bond strength values of artificial teeth and crosslink thermo-polymerizable acrylic resin

Effect of a Bioactive Glass Ceramic on the Control of Enamel and Dentin Erosion Lesions

Abstract This study evaluated the effect of a bioactive glass ceramic for the control of erosion and caries lesions. Fragments (n=10) of bovine enamel and root dentin received daily application of different treatments (Biosilicate; Acidulated Phosphate Fluoride- APF; Untreated - control) during the performance of erosive cycles. Surfaces were analyzed with 3D optical profilometry to quantify the superficial loss in four periods (1, 7, 14 and 21 days), as well as the lesion depth with confocal laser scanning microscopy. For caries progression assessment, initial Knoop microhardness was measured on enamel bovine fragments. Initial carious lesions were developed and specimens were divided into three groups (n=10), according to the daily topical application (Biosilicate; APF; no application - control), during the de-remineralization cycles for 14 days. Final microhardness was obtained to calculate the change of surface microhardness. Subsurface demineralization was analyzed using cross-sectional microhardness (depths 10, 30, 50, 70, 90, 110 and 220 µm). Data were tested using ANOVA and Tukey's test (a=5%). Results of erosive evaluation showed that Biosilicate promoted the lowest (p<0.05) values of surface loss, regardless of time, for both enamel and dentin; APF promoted lower (p<0.05) surface loss than control; analyzing different periods of time, APF did not show difference (p>0.05) between 14 and 21 days of demineralization. Results of enamel caries assessment showed that Biosilicate resulted in higher (p<0.05) surface and subsurface microhardness than both APF and control-applications. It may be concluded that Biosilicate application showed a higher potential to reduce surface loss and development of erosion and caries lesions.

Resumo Este estudo avaliou o efeito de uma vitrocerâmica bioativa para o controle de lesões de erosão e cárie. Fragmentos (n=10) de esmalte bovino e dentina radicular receberam aplicação diária de diferentes tratamentos (Biosilicato; Fluoreto de Fosfato Acidulado - APF; não tratado - controle) durante a realização de ciclos erosivos. As superfícies foram analisadas com profilometria óptica 3D para quantificar a perda superficial em quatro períodos (1, 7, 14 e 21 dias), bem como a profundidade da lesão com microscopia confocal de varredura a laser. Para a avaliação da progressão de cárie, foi obtida a microdureza Knoop inicial de fragmentos de esmalte bovino. As lesões cariosas iniciais foram desenvolvidas e os espécimes foram divididos em três grupos (n =10), de acordo com a aplicação tópica diária (Biosilicato; APF; sem aplicação - controle) durante os ciclos de desmineralização por 14 dias. A microdureza final foi obtida para calcular a perda da microdureza superficial. A desmineralização sub-superficial foi analisada utilizando microdureza transversal (profundidades 10, 30, 50, 70, 90, 110 e 220 μm). Os dados foram testados utilizando ANOVA e teste de Tukey (α=5%). Os resultados da avaliação erosiva mostraram que o Biosilicato promoveu os menores valores (p <0,05) de perda superficial, independente do tempo, tanto para o esmalte como para a dentina; APF promoveu menor (p <0,05) perda de superfície do que controle; analisando os períodos de tempo, APF não mostrou diferença (p>0,05) entre 14 e 21 dias de desmineralização. Os resultados da avaliação da cárie no esmalte mostraram que o Biosilicato resultou em maiores (p<0,05) valores de microdureza superficial e subsuperficial do que as aplicações APF e controle. Pode-se concluir que a aplicação de Biosilicato apresentou maior potencial de redução da perda superficial e desenvolvimento de lesões de erosão e cárie.

Effect of Er:Yag laser on dentin demineralization around restorations.

The aim of this study was to evaluate the effect of cavity preparation with Er:YAG laser on dentin adjacent to restorations submitted to cariogenic challenge in situ, by subsuperficial microhardness analysis. Bovine incisors were sectioned, flattened, and polished, resulting in 40 dentin slabs. The slabs were randomly assigned to four groups (n = 10), according to the cavity preparation method: I-high-speed handpiece (control); II-Er:YAG laser (160 mJ; 3 Hz); III-Er:YAG laser (260 mJ; 3 Hz); IV-Er:YAG laser (300 mJ; 3Hz). Cavities were restored with composite resin, and the specimens were fixed in intra-oral appliances, which were worn by 10 volunteers for 14 days for simulating cariogenic challenge in situ. During the experimental period, 20% sucrose solution was dripped over each specimen 6 times a day. Samples were removed, sectioned, and examined for subsuperficial Knoop microhardness at 100, 200, and 300 µm from the restoration and at 30 µm from dentin surface. Split-plot analysis of variance showed no significant difference among the cavity preparation techniques (p = 0.1129), among distances (p = 0.9030), as well as no difference in the interaction between the main factors (p = 0.7338). It was concluded that the cavity preparation with Er:YAG laser did not influence on dentin microhardness submitted to cariogenic challenge in situ.

Effect of Brushing Time and Dentifrice Abrasiveness on Color Change and Surface Roughness of Resin Composites

Abstract: Dentifrice abrasiveness and brushing time may increase color change (∆E) and surface roughness (∆Ra) of resin composites. This study aimed to evaluate the effect of mechanical brushing time of dentifrices with different abrasiveness on ∆E and ∆Ra of nanofilled (Z350, 3M ESPE) and nanohybrid (Tetric N-Ceram, Ivoclar Vivadent) resin composites. Sixteen specimens (12 mm diameter x 2 mm thick) were fabricated using a white Teflon matrix of each resin composite and a ceramic (IPS e.max Ceram, Ivoclar Vivadent), used as control. After initial color readouts on white backgrounds (Spectrophotometer PCB 6807, Byk Gardner), with D65 standard illuminant, and surface roughness (Rugosimeter Surfcorder SE 1700, Kosalab) with cut-off=0.8 mm and speed=0.25 mm/s, specimens were assigned (n=8) according to the abrasiveness of the dentifrices: RDA* 68 (Colgate) and RDA* 180 (Colgate Total Plus Whitening). Specimens were submitted to mechanical brushing (58,400 cycles) and after every 14,600 cycles (1 year of brushing by a healthy individual), new color and surface roughness readouts were taken. Color stability was calculated by CIEDE2000. Data were analyzed by 3-way repeated measures ANOVA and Bonferroni test (p<0.05), and demonstrated that the dentifrice abrasiveness (p=0.02) and brushing time (p<0.0001) affected the ∆E of nanofilled resin composite. There was no difference on surface roughness of materials (p=0.6752) or brushing time (p=0.7997). In conclusion, the longer the brushing time and dentifrice abrasiveness, the greater the color change of the nanofilled resin composite. The surface roughness was not influenced by dentifrice abrasiveness.

Resumo: A abrasividade do dentifrício e o tempo de escovação podem aumentar a alteração de cor (∆E) e rugosidade de superfície (∆Ra) das resinas compostas. Este estudo teve como objetivo avaliar o efeito do tempo de escovação mecânica com dentifrícios de diferentes abrasividades, sobre o ∆E e a ∆Ra das resinas compostas (nanoparticulada, Z350, 3M ESPE e nanohíbrida, Tetric N-Ceram, Ivoclar Vivadent). Dezesseis amostras (12 mm de diâmetro x 2 mm de espessura) foram obtidas utilizando uma matriz de teflon branca, de cada resina composta e uma cerâmica (IPS e.max Ceram, Ivoclar Vivadent), considerada como controle. Após as leituras iniciais de cor sobre fundo branco (Espectrofotômetro PCB 6807, Byk Gardner), com iluminante padrão D65, e de rugosidade de superfície (Rugosímetro Surfcorder SE 1700, Kosalab), com cut-off=0,8 mm e velocidade=0,25 mm/s, as amostras foram separadas (n=8) de acordo com a abrasividade dos dentifrícios: RDA* 68 (Colgate) e RDA* 180 (Colgate Total Plus Whitening). Amostras foram submetidas a escovação mecânica (58.400 ciclos), sendo que a cada 14.600 ciclos (1 ano de escovação por um indivíduo saudável), novas leituras de cor e rugosidade de superfície foram realizadas. A estabilidade de cor foi calculada segundo CIEDE2000. Os dados foram analisados (3-way ANOVA medidas repetidas, teste de Bonferroni, p<0,05), e demonstrou-se que a abrasividade dos dentifrícios (p=0,02) e o tempo de escovação (p<0,0001) afetaram o ∆E da resina composta nanoparticulada. A rugosidade de superfície não foi influenciada pela abrasividade dos dentifrícios (p=0,6752) ou tempo de escovação (p=0,7997). Concluiu-se que quanto maior o tempo de escovação mecânica e a abrasividade do dentifrício, maior a alteração de cor da resina composta nanoparticulada. A rugosidade de superfície não foi influenciada pela abrasividade do dentifrício.

Microleakage in conservative cavities varying the preparation method and surface treatment

OBJECTIVE: To assess microleakage in conservative class V cavities prepared with aluminum-oxide air abrasion or turbine and restored with self-etching or etch-and-rinse adhesive systems. Materials and Methods: Forty premolars were randomly assigned to 4 groups (I and II: air abrasion; III and IV: turbine) and class V cavities were prepared on the buccal surfaces. Conditioning approaches were: groups I/III - 37 percent phosphoric acid; groups II/IV - self-priming etchant (Tyrian-SPE). Cavities were restored with One Step Plus/Filtek Z250. After finishing, specimens were thermocycled, immersed in 50 percent silver nitrate, and serially sectioned. Microleakage at the occlusal and cervical interfaces was measured in mm and calculated by a software. Data were subjected to ANOVA and Tukey's test (α=0.05). RESULTS: Marginal seal provided by air abrasion was similar to high-speed handpiece, except for group I. There was SIGNIFICANT difference between enamel and dentin/cementum margins for to group I and II: air abrasion. The etch-and-rinse adhesive system promoted a better marginal seal. At enamel and dentin/cementum margins, the highest microleakage values were found in cavities treated with the self-etching adhesive system. At dentin/cementum margins, high-speed handpiece preparations associated with etch-and-rinse system provided the least dye penetration. CONCLUSION: Marginal seal of cavities prepared with aluminum-oxide air abrasion was different from that of conventionally prepared cavities, and the etch-and-rinse system promoted higher marginal seal at both enamel and dentin margins.

Effect of erbium:yttrium-aluminum-garnet laser energies on superficial and deep dentin microhardness.

This study evaluated the microhardness of superficial and deep dentin irradiated with different erbium:yttrium-aluminum-garnet (Er:YAG) laser energies. Seventy-two molars were bisected and randomly assigned to two groups (superficial dentin or deep dentin) and into six subgroups (160 mJ, 200 mJ, 260 mJ, 300 mJ, 360 mJ, and control). After irradiation, the cavities were longitudinally bisected. Microhardness was measured at six points (20 microm, 40 microm, 60 microm, 80 microm, 100 microm, and 200 microm) under the cavity floor. Data were submitted to analysis of variance (ANOVA) and Fisher's tests (alpha = 0.05). Superficial dentin presented higher microhardness than deep dentin; energy of 160 mJ resulted in the highest microhardness and 360 mJ the lowest one. Values at all points were different, exhibiting increasing microhardness throughout; superficial dentin microhardness was the highest at 20 microm with 160 mJ energy; for deep dentin, microhardness after irradiation at 160 mJ and 200 mJ was similar to that of the control. The lowest energy increased superficial dentin microhardness at the closest extent under the cavity; deep dentin microhardness was not altered by energies of 160 mJ and 200 mJ.

Surface and subsurface erosion of primary enamel by acid beverages over time

This study evaluated the influence of a cola-type soft drink and a soy-based orange juice on the surface and subsurface erosion of primary enamel, as a function of the exposure time. Seventy-five primary incisors were divided for microhardness test (n=45) or scanning electron microscopy (SEM) analysis (n=30). The specimens were randomly assigned to 3 groups: 1 - artificial saliva (control); 2 - cola-type soft drink; and 3 - soy-based orange juice. Immersion cycles in the beverages were undertaken under agitation for 5 min, 3 times a day, during 60 days. Surface microhardness was measured at 7, 15, 30, 45 and 60 days. After 60 days, specimens were bisected and subsurface microhardness was measured at 30, 60, 90, 120, 150 and 200 µm from the surface exposed. Data were analyzed by ANOVA and Tukey’s test (a=0.05). Groups 2 and 3 presented similar decrease of surface microhardness. Regarding subsurface microhardness, group 2 presented the lowest values. SEM images revealed that after 60 days the surfaces clearly exhibited structural loss, unlike those immersed in artificial saliva. It may be concluded that erosion of the surfaces exposed to the cola-type soft drink was more accentuated and directly proportional to the exposure time.

Este estudo avaliou a influência de um refrigerante a base de cola e um suco de laranja a base de soja na erosão da superfície e subsuperfície do esmalte do dente decíduo, em função do tempo de exposição. Setenta e cinco incisivos decíduos foram divididos para o teste de microdureza (n=45) ou para a análise em microscópio eletrônico de varredura (MEV) (n=30). Os espécimes foram alocados aleatoriamente em 3 grupos: I - saliva artificial (controle); II - refrigerante a base de cola; e III - suco de laranja a base de soja. Ciclos de imersão nas bebidas foram realizados sob agitação durante 5 min, 3 vezes ao dia, durante 60 dias. A microdureza superficial foi mensurada aos 7, 15, 30, 45 e 60 dias. Após 60 dias, os espécimes foram seccionados e a microdureza subsuperficial foi mensurada aos 30, 60, 90, 120, 150 e 200 μm. Os dados foram analisados pelos testes ANOVA e Tukey (α=5 por cento). Os grupos II e III apresentam uma diminuição similar da microdureza superficial. O grupo II apresentou menores valores de microdureza subsuperficial. As imagens de MEV revelaram que após 60 dias as superficies mostraram perdas de estruturas claramentes identificadas, diferentemente das superfícies imersas em saliva artificial. Pode-se concluir que a erosão das superficies expostas ao refrigerante a base de cola foi mais acentuada e diretamente proporcional ao tempo de exposição à bebida.

Effectiveness of home bleaching agents in discolored teeth and influence on enamel microhardness

OBJECTIVES: This study evaluated the effectiveness of different home bleaching agents on color alteration and their influence on surface and subsurface microhardness of discolored bovine enamel. MATERIAL AND METHODS: Forty-five fragments of bovine incisors were randomly allocated into 3 groups (n=15) according to the bleaching agent: 10 percent carbamide peroxide gel (CP10), 16 percent carbamide peroxide gel (CP16) and 6.5 percent-hydrogen-peroxide-based strip (HP6.5). Before bleaching treatment, initial values of Knoop surface microhardness and color (CIEL*a*b*) were obtained and the fragments were artificially stained in hemolyzed rat blood. Then, bleaching treatments were performed over a 21-day period. Color changes (ÄE) were assessed at 7, 14 and 21 days, and final surface microhardness reading was done after 21 days. Thereafter, the fragments were bisected to obtain subsurface microhardness. Data were subjected to ANOVA and Tukey's tests (á=5 percent). RESULTS: Color changes produced by CP16 were similar to those of CP10, and the color changes produced by these materials were significantly superior to those produced by HP6.5. Color changes at 21 days were superior to 7 days and similar to 14 days. The time did not influence color changes for CP16, which showed similarity between the 14- and 21-day results. No statistically significant differences were found among the home bleaching agents for surface and subsurface microhardness. CONCLUSIONS: Microhardness of bovine enamel was not affected by the bleaching agents. The 16 percent carbamide peroxide gel was the most effective for bleaching the stained substrate.

Ablation rate and morphology of superficial and deep dentin irradiated with different Er:YAG laser energy levels.

OBJECTIVE: In this study we evaluated the ablation rate of superficial and deep dentin irradiated with different Er:YAG laser energy levels, and observed the micromorphological aspects of the lased substrates with a scanning electron microscope (SEM). BACKGROUND DATA: Little is known about the effect of Er:YAG laser irradiation on different dentin depths. MATERIALS AND METHODS: Sixty molar crowns were bisected, providing 120 specimens, which were randomly assigned into two groups (superficial or deep dentin), and later into five subgroups (160, 200, 260, 300, or 360 mJ). Initial masses of the specimens were obtained. After laser irradiation, the final masses were obtained and mass losses were calculated followed by the preparation of specimens for SEM examination. Mass-loss values were subjected to two-way ANOVA and Fisher's least significant difference multiple-comparison tests (p > 0.05). RESULTS: There was no difference between superficial and deep dentin. A significant and gradual increase in the mass-loss values was reached when energies were raised, regardless of the dentin depth. The energy level of 360 mJ showed the highest values and was statistically significantly different from the other energy levels. The SEM images showed that deep dentin was more selectively ablated, especially intertubular dentin, promoting tubule protrusion. At 360 mJ the micromorphological features were similar for both dentin depths. CONCLUSION: The ablation rate did not depend on the depth of the dentin, and an energy level lower than 360 mJ is recommended to ablate both superficial and deep dentin effectively without causing tissue damage.

Influence of energy and pulse repetition rate of Er:YAG laser on enamel ablation ability and morphological analysis of the laser-irradiated surface.

OBJECTIVE: To assess the influence of energy and pulse repetition rate of Er:YAG laser on the enamel ablation ability and substrate morphology. METHODS: Fifteen crowns of molars were sectioned in four fragments, providing 60 samples, which were ground to flatten the enamel surface. The initial mass was obtained by weighing the fragments. The specimens were hydrated for 1 h, fixed, and a 3-mm-diameter area was delimited. Twelve groups were randomly formed according to the combination of laser energies (200, 250, 300, or 350 mJ) and pulse repetition rates (2, 3, or 4 Hz). The final mass was obtained and mass loss was calculated by the difference between the initial and final mass. The specimens were prepared for SEM. Data were submitted to ANOVA and Scheffé test. RESULTS: The 4 Hz frequency resulted in higher mass loss and was statistically different from 2 and 3 Hz (p < 0.05). The increase of frequency produced more melted areas, cracks, and unselective and deeper ablation. The 350 mJ energy promoted greater mass loss, similar to 300 mJ. CONCLUSIONS: The pulse repetition rate influenced more intensively the mass loss and morphological alteration. Among the tested parameters, 350 mJ/3 Hz improved the ability of enamel ablation with less surface morphological alterations.

Effect of energy and pulse repetition rate of Er: YAG laser on dentin ablation ability and morphological analysis of the laser-irradiated substrate.

OBJECTIVE: The aim of this study was to assess the effect of energy and pulse repetition rate of the Er:YAG laser (2.94 microm) on dentin ablation ability and substrate morphology. BACKGROUND DATA: Previous studies have demonstrated the ability of the Er:YAG laser for ablating dentin substrate. METHODS: Fifteen crowns of molars were sectioned in four fragments, providing 60 samples, which were ground to expose dentin. Initial mass was obtained by weighing the fragments. Twelve groups were randomly formed, according to the combination of laser energies (200, 250, 300, and 350 mJ) and pulse repetition rates (2, 3, and 4 Hz), usually advised for cavity preparation. The final mass was obtained, and dentin mass loss was calculated by the difference between the final and initial mass. Afterwards, specimens were prepared for scanning electron microscopy (SEM). Data were submitted to analysis of variance (ANOVA) and Scheffé test (p < 0.05). RESULTS: Pulse repetition rate of 4 Hz was statistically similar to 3 Hz, and laser energy of 350 mJ was statistically similar to 300 mJ. Increased pulse repetition rates provided higher ablation depth and slight enlargement of dentinal tubules, whereas increased energies yielded greater ablation of intertubular dentin. CONCLUSION: The ablation ability of the Er:YAG laser on dentin raised with the increase of energy and/or pulse repetition rate, the latter exhibiting a stronger influence on mass loss rate and on morphological alterations.

Effect of Er:YAG laser irradiation distance on superficial dentin morphology.

PURPOSE: To assess in vitro the effect of Er:YAG laser irradiation distance on dentin surface morphology, by SEM. METHODS: 60 sound human third molars were employed to obtain discs (approximately equal to 1mm thick), that were polished to standardize the smear layer. Discs were randomly assigned to six groups (n=10) and sequentially bisected. Five groups (including both disc halves of each sample) received Er:YAG laser irradiation (80mJ/2Hz) for 20s, according to the irradiation distance (11, 12, 14, 16 or 17mm) and one was the control group. In the lased-groups, one disc half was separated for superficial analysis without subsequent acid-etching and the other half received phosphoric acid for 15 seconds. In the control group, one disc half was treated with phosphoric acid and no superficial treatment was done in the other half. Specimens were prepared for SEM. RESULTS: Er:YAG laser-irradiated specimens, regardless of the irradiation distance, showed an irregular and scaly surface, with intense ablation of the intertubular dentin, mainly when the irradiation was performed in the focused mode (12 mm). The smear layer was removed and dentin tubules were opened, however, no tubule enlargement was found, unlike the group that only received acid application. The irradiation with 17 mm resulted in a surface appearance more homogeneous than those presented with other distances closer to the focus. The subsequent acid-etching on the lased surfaces decreased the superficial irregularities with partial exposure and enlargement of dentin tubules, in all the tested irradiation distances.

Evaluation of the surface hardness of composite resins before and after polishing at different times

PURPOSE: The aim of this study was to evaluate the surface hardness of six composite resins: Revolution, Natural Flow, Fill Magic Flow, Flow-it! (flowables), Silux Plus (microfilled) and Z100 (minifilled) before and after polishing at different times. MATERIALS AND METHODS: For this purpose, 240 specimens (5mm diameter, 1.4mm high) were prepared. Vickers hardness was determined before and after polishing at different times: immediately, 24h, 7 and 21 days after preparation of the samples. Statistical analysis was performed by ANOVA and Tukey test. RESULTS: There was no difference in the hardness of flowable resins, which had lower hardness than the minifilled resin. The minifilled resin showed the highest surface hardness as compared to the other materials (p<0.01). All materials exhibited higher hardness after polishing, being more evident after 7 days. CONCLUSION: It may be concluded that, regardless of the composite resin, surface hardness was considerably increased when polishing was delayed and performed 1 week after preparation of the samples.

PROPOSIÇÃO: O objetivo deste estudo foi avaliar a dureza superficial de seis resinas compostas - Revolution, Natural Flow, Fill Magic Flow, Flow-it! (flowables), Silux Plus (micropartículas) e Z100 (híbrida) - antes e após o polimento realizado em diferentes tempos. MATERIAL E MÉTODO: Foram confeccionados 240 corpos-de-prova circulares (5mm de diâmetro e 1,4mm de altura). A dureza Vickers foi obtida antes e após o polimento realizado em diferentes tempos: imediatamente, 24 horas, 7 dias e 21 dias após a confecção do corpo-de-prova. Os dados foram analisados estatisticamente por meio da ANOVA e do Teste de Tukey. RESULTADOS: Não houve diferença entre as resinas compostas flowable, as quais apresentaram os menores valores de dureza. A resina composta híbrida demonstrou os melhores resultados. Todos os materiais exibiram aumento de dureza após a realização do polimento, que foi mais evidente após 7 dias. CONCLUSÃO: Pôde-se concluir que, independente do tipo de resina composta, a dureza superficial foi consideravelmente maior quando o polimento foi realizado 1 semana após a confecção dos corpos-de-prova.

Evaluation of the surface hardness of composite resins before and after polishing at different times%Avaliação da dureza superficial de resinas compostas antes e após o polimento em diferentes tempos

PROPOSIÇÃO: O objetivo deste estudo foi avaliar a dureza superficial de seis resinas compostas - Revolution, Natural Flow, Fill Magic Flow, Flow-it! (flowables), Silux Plus (micropartículas) e Z100 (híbrida) - antes e após o polimento realizado em diferentes tempos. MATERIAL E MÉTODO: Foram confeccionados 240 corpos-de-prova circulares (5mm de diâmetro e 1,4mm de altura). A dureza Vickers foi obtida antes e após o polimento realizado em diferentes tempos: imediatamente, 24 horas, 7 dias e 21 dias após a confecção do corpo-de-prova. Os dados foram analisados estatisticamente por meio da ANOVA e do Teste de Tukey. RESULTADOS: Não houve diferença entre as resinas compostas flowable, as quais apresentaram os menores valores de dureza. A resina composta híbrida demonstrou os melhores resultados. Todos os materiais exibiram aumento de dureza após a realização do polimento, que foi mais evidente após 7 dias. CONCLUSÃO: Pôde-se concluir que, independente do tipo de resina composta, a dureza superficial foi consideravelmente maior quando o polimento foi realizado 1 semana após a confecção dos corpos-de-prova

Microinfiltração marginal em Cavidades Preparadas com Pontas CVDentUS® e Diamantadas Convencionais / Marginal Microleakage in Cavities Prepared with CVDentUS® and Conventional Diamonds Burs

O objetivo deste trabalho foi avaliar a microinfiltração marginal em cavidades restritas ao esmalte de dentes bovinos preparados com as pontas CVDentUS® e diamantadas convencionais. Foram realizados preparos cavitários medindo 1mm de profundidade em dois grupos de 15 dentes cada, utilizando ponta diamantada convencional associado à turbina de alta rotação e ponta CVDentUS® associado ao ultra-som. As cavidades foram restauradas com selante para fóssulas e fissuras Fluroshield® (Dentsply) de acordo com as instruções do fabricante. Após serem isolados com Araldite® e esmalte cosmético, os dentes foram submetidos a termociclagem em água a 5°C± 2°C e 55°C± 2°C, totalizando 500 ciclos. Em seguida, foram corados com fucsina básica a 0,5%, seccionados e lixados até ficarem com aproximadamente 0,25mm de espessura, montados em lâminas e identificados. A análise da microinfiltração foi realizada em microscópio óptico ligado a uma câmara digital e conectado a um computador, que permitiu a análise quantitativa da microinfiltração em milímetros por meio de uma imagem digitalizada e um software AxioVision. Os dados obtidos foram submetidos à análise estatística através do teste de Mann-Whitney. Foi observada acentuada microinfiltração marginal em ambos os grupos sem diferença estatistica entre eles (p > 0,05)

Avaliação da eficiência de pontas diamantadas / Cutting efficiency of diamond points

O objetivo do presente estudo foi avaliar a eficiência de desgaste sobre dentes bovinos de pontas diamantadas de diferentes marcas comerciais (KG Sorensen, Microdont, Fava e SSWhinte). Para tal finalidade, foram testados 10 pontas de cada marca comercial, cujo substrato para o desgaste constituía-se de incisivos bovinos, seccionados em 4 partes iguais (2 cervicais e 2 incisais) e incluídos em resina de poliéster, totalizando 4 espécimes para cada instrumento rotatório. Para padronização do desgaste, foi utilizado um dispositivo, no qual acoplou-se a caneta de alta-rotação. Todos os testes foram executados sob refrigeração constante e as pontas foram divididas aleatoriamente e sem identificação. Os dados forma analisados através de Análise de Variância a dois critérios (p<0,01) e teste de Tukey (p<0,05). Pode-se observar que as pontas diamantadas KG Soresen demonstraram estatisticamente maior eficiência no desgaste do que as demais pontas testadas, sendo mais evidenciado após o 2° secção de dente. Através dos resultados obtidos, pode-se concluir que as pontas diamantadas KG apresentaram melhor desempenho tanto na porção incisal quanto na cervical

In vitro evaluation of microleakage of a flowable composite in class V restorations

The aim of this study was to evaluate microleakage around class V restorations using a flowable composite compared to a hybrid composite. Forty class V cavities were prepared on buccal and lingual surfaces of 20 human teeth, with occlusal and cervical margins at the enamel and cementum/dentin levels, respectively. Specimens were divided into 2 groups with 10 samples each. Group 1: buccal cavities received Paama 2 (conventional bonding agent) + Wave (flowable composite); lingual cavities were restored with Paama 2 + Glacier (hybrid composite). Group 2: buccal cavities received Optibond Solo (self-priming bonding agent) + Wave; lingual cavities were restored with Optibond Solo + Glacier. After being stored in distilled water and finished, the teeth were thermocycled, immersed in a 50 percent silver nitrate solution and embedded in resin. They were sectioned and the depth of tracer penetration was scored. The results were analyzed using Kruskall-Wallis and Wilcoxon tests. The restorations with flowable composite and those with hybrid composite from the same group showed similar results of microleakage for both occlusal and cervical margins. Optibond Solo improved the sealing of the restorations when compared with Paama 2 (p<0.01). None of the restorative materials completely sealed the tooth/restoration interface at the cervical margins