Introducing an lsoprenaline Eluting Guidewire: Report on its Design and the Results of the Dose-Determining Pilot Study.

Introduction: Retrograde intrarenal surgery (RIRS) is associated with complications, many of which are related to the intrarenal pressure (IRP). We aim to describe the design of a novel isoprenaline-eluting guidewire ("IsoWire") and present the results from the first in vitro release studies and the first animal studies showing its effect on IRP. Materials and Methods: The IsoWire comprises a Nitinol core surrounded by a stainless-steel wire wound into a tight coil. The grooves created by this coil provided a reservoir for adding a hydrogel coating into which isoprenaline, a beta-agonist, was loaded. Animal studies were performed using a porcine model. For the control, IRP, heart rate (HR), and mean arterial pressure (MAP) were measured continuously for 6 minutes with a standard guidewire in place. For the experiment, the standard hydrophilic guidewire was removed, the IsoWire was inserted into the renal pelvis, and the same parameters were measured. Results: In vitro analysis of the isoprenaline release profile showed that most (63.9 ± 5.9%) of the loaded drug mass was released in the 1st minute, and almost all of the drug was released in the first 4 minutes exponentially. Porcine studies showed a 25.1% reduction in IRP in the IsoWire that released 10 µg in the 1st minute; however, there was a marked increase in HR. The average percentage reduction in IRP was 8.95% and 21.3% in the IsoWire that released 5 and 7.5 µg of isoprenaline, respectively, with no changes in HR or MAP. Conclusions: The IsoWire, which releases 5 and 7.5 µg of isoprenaline in the 1st minute, appears to be safe and effective in reducing the IRP. Further studies are needed to establish whether the isoprenaline-induced ureteral relaxation will render easier insertion of a ureteral access sheath, reduce IRP during sheathless RIRS, or even promote the practice of sheathless RIRS.

Nanoparticle-Encapsulated Epirubicin Efficacy in the Inhibition of Growth of Orthotopic Ovarian Patient-Derived Xenograft in Immunocompromised Mice.

Epirubicin hydrochloride (EPI) is an anticancer drug widely used in the treatment of many solid tumors, including ovarian cancer. Because of its anatomical location, ovarian cancer shows symptoms when it is already in an advanced stage and is thus more difficult to treat. Epirubicin hydrochloride kills cancer cells effectively, but its dose escalation is limited by its severe toxicity. By encapsulating epirubicin in dextran-based nanoparticles (POLEPI), we expected to deliver higher and thus clinically more effective doses directly to tumors, where epirubicin would be released and retained longer in the tumor. The antitumor activity of POLEPI compared to EPI was first tested ex vivo in a series of ovarian cancer patient-derived tumor xenografts (PDX). The most promising PDX was then implanted orthotopically into immunocompromised mice, and tumor growth was monitored via magnetic resonance imaging (MRI). Although we succeeded in suppressing the growth of ovarian cancer derived from a patient, in a mouse model by 70% compared to 40% via EPI in 5 days after only one injection, we could not eliminate serious side effects, and the study was terminated prematurely for humane reasons.

Study on Saccharide-Glucose Receptor Interactions with the Use of Surface Plasmon Resonance.

The aim of this study was to investigate the process of attachment of saccharide particles differing in degree of complexity to cell receptors responsible for transport of glucose across the cell membrane (GLUT proteins). This phenomenon is currently considered when designing modern medicines, e.g., peptide drugs to which glucose residues are attached, enabling drugs to cross the barrier of cell membranes and act inside cells. This study aims to help us understand the process of assimilation of polysaccharide nanoparticles by tumour cells. In this study, the interactions between simple saccharides (glucose and sucrose) and dextran nanoparticles with two species of GLUT proteins (GLUT1 and GLUT4) were measured using the surface plasmon resonance technique. We managed to observe the interactions of glucose and sucrose with both applied proteins. The lowest concentration that resulted in the detection of interaction was 4 mM of glucose on GLUT1. Nanoparticles were measured using the same proteins with a detection limit of 40 mM. These results indicate that polysaccharide nanoparticles interact with GLUT proteins. The measured strengths of interactions differ between proteins; thus, this study can suggest which protein is preferable when considering it as a mean of nanoparticle carrier transport.

Composite microgranular scaffolds with surface modifications for improved initial osteoblastic cell proliferation.

Polyester-based granular scaffolds are a potent material for tissue engineering due to their porosity, controllable pore size, and potential to be molded into various shapes. Additionally, they can be produced as composite materials, e.g., mixed with osteoconductive ß-tricalcium phosphate or hydroxyapatite. Such polymer-based composite materials often happen to be hydrophobic, which disrupts cell attachment and decreases cell growth on the scaffold, undermining its primary function. In this work, we propose the experimental comparison of three modification techniques for granular scaffolds to increase their hydrophilicity and cell attachment. Those techniques include atmospheric plasma treatment, polydopamine coating, and polynorepinephrine coating. Composite polymer/ß-tricalcium phosphate granules have been produced in a solution-induced phase separation (SIPS) process using commercially available biomedical polymers: poly(lactic acid), poly(lactic-co-glycolic acid), and polycaprolactone. We used thermal assembly to prepare cylindrical scaffolds from composite microgranules. Atmospheric plasma treatment, polydopamine coating, and polynorepinephrine coating showed similar effects on polymer composites' hydrophilic and bioactive properties. All modifications significantly increased human osteosarcoma MG-63 cell adhesion and proliferation in vitro compared to cells cultured on unmodified materials. In the case of polycaprolactone/ß-tricalcium phosphate scaffolds, modifications were the most necessary, as unmodified polycaprolactone-based material disrupted the cell attachment. Modified polylactide/ß-tricalcium phosphate scaffold supported excellent cell growth and showed ultimate compressive strength exceeding this of human trabecular bone. This suggests that all investigated modification techniques can be used interchangeably for increasing wettability and cell attachment properties of various scaffolds for medical applications, especially those with high surface and volumetric porosity, like granular scaffolds.

Antimicrobial Peptides: Challenging Journey to the Pharmaceutical, Biomedical, and Cosmeceutical Use.

Antimicrobial peptides (AMPs), or host defence peptides, are short proteins in various life forms. Here we discuss AMPs, which may become a promising substitute or adjuvant in pharmaceutical, biomedical, and cosmeceutical uses. Their pharmacological potential has been investigated intensively, especially as antibacterial and antifungal drugs and as promising antiviral and anticancer agents. AMPs exhibit many properties, and some of these have attracted the attention of the cosmetic industry. AMPs are being developed as novel antibiotics to combat multidrug-resistant pathogens and as potential treatments for various diseases, including cancer, inflammatory disorders, and viral infections. In biomedicine, AMPs are being developed as wound-healing agents because they promote cell growth and tissue repair. The immunomodulatory effects of AMPs could be helpful in the treatment of autoimmune diseases. In the cosmeceutical industry, AMPs are being investigated as potential ingredients in skincare products due to their antioxidant properties (anti-ageing effects) and antibacterial activity, which allows the killing of bacteria that contribute to acne and other skin conditions. The promising benefits of AMPs make them a thrilling area of research, and studies are underway to overcome obstacles and fully harness their therapeutic potential. This review presents the structure, mechanisms of action, possible applications, production methods, and market for AMPs.

In vitro immune evaluation of adenoviral vector-based platform for infectious diseases.

New prophylactic vaccine platforms are imperative to combat respiratory infections. The efficacy of T and B memory cell-mediated protection, generated through the adenoviral vector, was tested to assess the effectiveness of the new adenoviral-based platforms for infectious diseases. A combination of adenovirus AdV1 (adjuvant), armed with costimulatory ligands (ICOSL and CD40L), and rRBD (antigen: recombinant nonglycosylated spike protein rRBD) was used to promote the differentiation of T and B lymphocytes. Adenovirus AdV2 (adjuvant), without ligands, in combination with rRBD, served as a control. In vitro T-cell responses to the AdV1+rRBD combination revealed that CD8+ platform-specific T-cells increased (37.2 ± 0.7% vs. 23.1 ± 2.1%), and T-cells acted against SARS-CoV-2 via CD8+TEMRA (50.0 ± 1.3% vs. 36.0 ± 3.2%). Memory B cells were induced after treatment with either AdV1+rRBD (84.1 ± 0.8% vs. 82.3 ± 0.4%) or rRBD (94.6 ± 0.3% vs. 82.3 ± 0.4%). Class-switching from IgM and IgD to isotype IgG following induction with rRBD+Ab was observed. RNA-seq profiling identified gene expression patterns related to T helper cell differentiation that protect against pathogens. The analysis determined signaling pathways controlling the induction of protective immunity, including the MAPK cascade, adipocytokine, cAMP, TNF, and Toll-like receptor signaling pathway. The AdV1+rRBD formulation induced IL-6, IL-8, and TNF. RNA-seq of the VERO E6 cell line showed differences in the apoptosis gene expression stimulated with the platforms vs. mock. In conclusion, AdV1+rRBD effectively generates T and B memory cell-mediated protection, presenting promising results in producing CD8+ platform-specific T cells and isotype-switched IgG memory B cells. The platform induces protective immunity by controlling the Th1, Th2, and Th17 cell differentiation gene expression patterns. Further studies are required to confirm its effectiveness.

Chitosan-poly(ethylene oxide) nanofibrous mat as a vaginal platform for tenofovir disoproxyl fumarate - The effect of vaginal pH on drug carrier performance.

In the present work, a solution blow spun nanofibrous mat comprised of chitosan (CS) and poly(ethylene oxide) (PEO) was obtained as vaginal platform for tenofovir disoproxil fumarate (TDF) to prevent sexually transmitted infections. Apart from physicochemical and mechanical analysis, the specific steps involved studies on nanofibrous mat mucoadhesive and swelling characteristics upon pH fluctuations over the physiological range. Physicochemical analysis showed uniform drug distribution within the CS/PEO mat volume and pointed toward physical interactions between the drug and polymers. TDF-loaded CS/PEO nanofibrous mat was shown potentially safe when evaluated by the MTT metabolic activity and JC-1 assays in human vaginal epithelial cells VK2-E6/E7. In vitro antiviral studies indicated inhibition efficacy of TDF-CS/PEO nanofibrous mat toward HSV-2 virus and proved the SBS process does not change the microbicidal activity of drug molecule. Fluctuations in the physiological vaginal pH range of 3.8 to 5.0 substantially affected mucoadhesive and swelling behavior of chitosan which in turn impacted drug dissolution rate from polymer carrier. The rate of permeation and accumulation of TDF in vaginal tissue differed in response to vaginal pH. Faster drug permeation assessed at pH 5.0 suggests that an increase in vaginal pH could improve TDF bioavailability at earlier time points.

Multifunctional Nanoparticles Based on Iron Oxide and Gold-198 Designed for Magnetic Hyperthermia and Radionuclide Therapy as a Potential Tool for Combined HER2-Positive Cancer Treatment.

Iron oxide nanoparticles are commonly used in many medical applications as they can be easily modified, have a high surface-to-volume ratio, and are biocompatible and biodegradable. This study was performed to synthesize nanoparticles designed for multimodal HER2-positive cancer treatment involving radionuclide therapy and magnetic hyperthermia. The magnetic core (Fe3O4) was coated with a gold-198 layer creating so-called core-shell nanoparticles. These were then further modified with a bifunctional PEG linker and monoclonal antibody to achieve the targeted therapy. Monoclonal antibody-trastuzumab was used to target specific breast and nipple HER2-positive cancer cells. The nanoparticles measured by transmission electron microscopy were as small as 9 nm. The bioconjugation of trastuzumab was confirmed by two separate methods: thermogravimetric analysis and iodine-131 labeling. Synthesized nanoparticles showed that they are good heat mediators in an alternating magnetic field and exhibit great specific binding and internalization capabilities towards the SKOV-3 (HER2 positive) cancer cell line. Radioactive nanoparticles also exhibit capabilities regarding spheroid degradation without and with the application of magnetic hyperthermia with a greater impact in the case of the latter. Designed radiobioconjugate shows great promise and has great potential for in vivo studies regarding magnetic hyperthermia and radionuclide combined therapy.

Chitosan-Enriched Solution Blow Spun Poly(Ethylene Oxide) Nanofibers with Poly(Dimethylsiloxane) Hydrophobic Outer Layer for Skin Healing and Regeneration.

Chitosan (CS)/poly(ethylene oxide) (PEO)-based nanofiber mats have attracted particular attention as advanced materials for medical and pharmaceutical applications. In the scope of present studies, solution blow spinning was applied to produce nanofibers from PEO and CS and physicochemical and biopharmaceutical studies were carried out to investigate their potential as wound nanomaterial for skin healing and regeneration. Additional coating with hydrophobic poly(dimethylsiloxane) was applied to favor removal of nanofibers from the wound surface. Unmodified nanofibers displayed highly porous structure with the presence of uniform, randomly aligned nanofibers, in contrast to coated materials in which almost all the free spaces were filled in with poly(dimethylsiloxane). Infrared spectroscopy indicated that solution blow technique did not influence the molecular nature of native polymers. Obtained nanofibers exhibited sufficient wound exudate absorbency, which appears beneficial to moisturize the wound bed during the healing process. Formulations displayed greater tensile strength as compared to commercial hydrofiber-like dressing materials comprised of carboxymethylcellulose sodium or calcium alginate, which points toward their protective function against mechanical stress. Coating with hydrophobic poly(dimethylsiloxane) (applied to favor nanofiber removal from the wound surface) impacted porosity and decreased both mechanical properties and adherence to excised human skin, though the obtained values were comparable to those attained for commercial hydrofiber-like materials. In vitro cytotoxicity and irritancy studies showed biocompatibility and no skin irritant response of nanofibers in contact with a reconstituted three-dimensional human skin model, while scratch assay using human fibroblast cell line HDFa revealed the valuable potential of CS/PEO nanofibers to promote cell migration at an early stage of injury.

Effect of Extreme Ultraviolet (EUV) Radiation and EUV Induced, N2 and O2 Based Plasmas on a PEEK Surface's Physico-Chemical Properties and MG63 Cell Adhesion.

Polyetheretherketone (PEEK), due to its excellent mechanical and physico-chemical parameters, is an attractive substitute for hard tissues in orthopedic applications. However, PEEK is hydrophobic and lacks surface-active functional groups promoting cell adhesion. Therefore, the PEEK surface must be modified in order to improve its cytocompatibility. In this work, extreme ultraviolet (EUV) radiation and two low-temperature, EUV induced, oxygen and nitrogen plasmas were used for surface modification of polyetheretherketone. Polymer samples were irradiated with 100, 150, and 200 pulses at a 10 Hz repetition rate. The physical and chemical properties of EUV and plasma modified PEEK surfaces, such as changes of the surface topography, chemical composition, and wettability, were examined using atomic force microscopy (AFM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and goniometry. The human osteoblast-like MG63 cells were used for the analysis of cell viability and cell adhesion on all modified PEEK surfaces. EUV radiation and two types of plasma treatment led to significant changes in surface topography of PEEK, increasing surface roughness and formation of conical structures. Additionally, significant changes in the chemical composition were found and were manifested with the appearance of new functional groups, incorporation of nitrogen atoms up to ~12.3 at.% (when modified in the presence of nitrogen), and doubling the oxygen content up to ~25.7 at.% (when modified in the presence of oxygen), compared to non-modified PEEK. All chemically and physically changed surfaces demonstrated cyto-compatible and non-cytotoxic properties, an enhancement of MG63 cell adhesion was also observed.

Chitosan-Human Bone Composite Granulates for Guided Bone Regeneration.

The search for the perfect bone graft material is an important topic in material science and medicine. Despite human bone being the ideal material, due to its composition, morphology, and familiarity with cells, autografts are widely considered demanding and cause additional stress to the patient because of bone harvesting. However, human bone from tissue banks can be used to prepare materials in eligible form for transplantation. Without proteins and fats, the bone becomes a non-immunogenic matrix for human cells to repopulate in the place of implantation. To repair bone losses, the granulate form of the material is easy to apply and forms an interconnected porous structure. A granulate composed of ß-tricalcium phosphate, pulverized human bone, and chitosan-a potent biopolymer applied in tissue engineering, regenerative medicine, and biotechnology-has been developed. A commercial encapsulator was used to obtain granulate, using chitosan gelation upon pH increase. The granulate has been proven in vitro to be non-cytotoxic, suitable for MG63 cell growth on its surface, and increasing alkaline phosphatase activity, an important biological marker of bone tissue growth. Moreover, the granulate is suitable for thermal sterilization without losing its form-increasing its convenience for application in surgery for guided bone regeneration in case of minor or non-load bearing voids in bone tissue.

PSMA targeted conjugates based on dextran.

BACKGROUND: Currently, radiotherapy is one of the most popular choices in clinical practice for the treatment of cancers. While it offers a fantastic means to selectively kill cancer cells, it can come with a host of side effects. To minimize such side effects, and maximize the therapeutic effect of the treatment, we propose the use of targeted radiopharmaceuticals. In the study presented herein, we investigate two synthetic pathways of dextran-based radiocarriers and provide their key chemical and physical properties: stability of the bonding of chelating agent and tertiary structure of obtained formulations and its influence on biological properties. Additionally, PSMA small molecule inhibitor was attached and quantified using DELFIA fluorescence assay. Finally, biological properties and radiolabeling yield were studied using confocal microscopy and ITLC-SG chromatography. RESULTS: Two types of Dex-conjugates - micelle-like nanoparticles (NPs) and non-folded conjugates - were successfully generated and shown to exhibit cellular effects. The tertiary structure of the conjugates was found to influence the selectivity of PSMA and mediate cell binding as well as cellular uptake mechanisms. NPs were shown to be internalized by other, non - PSMA mediated channels. Simultaneously, the uptake of non-folded conjugates required PSMA inhibitor to pass through cell membrane. The radiochemical yield of NHS coupled DOTA chelator was between 91.3 and 97.7% while the TCT-amine bonding showed higher stability and gave the yields of 99.8-100%. CONCLUSIONS: We obtained novel, dextran-based radioconjugates, and presented a superior method of chelator binding, resulting in exquisite radiochemical properties as well as selective cross-membrane transport.

Fenton-type reaction grafting of polyvinylpyrrolidone onto polypropylene membrane for improving hemo- and biocompatibility.

Known techniques for modification of polypropylene membranes (PPm) often require modification of the membrane in its entire volume (i.e. at the manufacturing stage), which may affect its properties. In the present work, the authors proposed a simple method for PPm hydrophilization. The process involves a two-step Fenton-type reaction, with ethylene glycol dimethacrylate (EGDMA) as a crosslinking agent and cumene hydroperoxide (CHP) as a source of free radicals. This hydrogel coating aims to enhance membrane hemocompatible and biocompatible properties. The biggest advantage of the proposed technique is the change of materials' surface properties, without interfering with its internal structure. Microscopic (SEM) and spectroscopic (FTIR-ATR) analyses confirmed the presence of hydrogel coating on PPm surfaces. Additionally, the evaluation of the surface density of the coating showed that the thickness of the coating increases with the reaction time and CHP concentration. The applied coatings significantly increase surface hydrophilicity (contact angle for PPm: 128.58°â€¯±â€¯0.52°, for all modified surfaces <53.31°â€¯±â€¯2.03°). The cytotoxicity test (XTT assay) proved biocompatibility of the PVP coating - cell viability remained above 90% for all variants tested. The modification resulted in a decrease in fibrinogen adsorption (of at least about 16%) and in a number of surface-adhered platelets. The assay evaluating the amount of secreted cell adhesion molecules (ICAM-1) showed a significant reduction (of at least about 50%) in the expression of ICAM-1 for all hydrogel-modified surfaces.

Patient specific implants for jawbone reconstruction after tumor resection.

In case of benign and malignant tumours affecting the maxillofacial region, the resection of jawbone reflects the standard therapy in more than 5.000 cases per year within the European Union. The resulting large bone defects lead to scarred, mangled facial appearance, loss of mastication and probably speech, requiring aesthetic and functional surgery as a basis for physical and physiological rehabilitation. Although autologous vascularized bone autografts reflect the current golden standard, the portion of bone available for the procedure is limited and subsequent high-dose anti-cancer chemo-/radiotherapy can lead to local tissue necrosis. Autologous vascularized bone from fibular or iliac-crest autografts is current golden standard in jawbone resection post-treatment, however, the portion of transplantable bone is limited and subsequent high-dose anti-cancer chemo-/radiotherapy often results in tissue necrosis Our research focuses on alternative treatment techniques: tissue reconstruction via novel patient-specifically manufactured maxillofacial implant that stimulates bone tissue growth. The planned neoformation of vascularized bone in such implants within the patient's own body as "bioreactor" is the safest approach in tissue engineering. The works described herein included the design of the metallic substrate of the implant with the use of computed tomography basing on real patients scans and then 3D-printing the substrates from the Ti6Al7Nb powder. The metal core was then evaluated in terms of structural characteristic, cytotoxicity and gene expression through the in vitro tests. Further experiments were focused on fabrication of the biocompatible coating for outer surface of the bone implant that would enhance the healing process and accelerate the tissue growth. Functional polymeric granulate dedicated for osteoconductive, osteoinductive and osteogenesis properties were elaborated. Another approach including the coating for the implant surface with two-phase biocompatible layer including polymeric microspheres and hydrogel carrier, which would provide long-time release of bone and cartilage growth factors around the implant were also done. The polymeric granulate containing ßTCP improved bone cells growth, but it some modification has to be done in order to improve structural pores to ensure for better osteoconductivity. The biocompatible coating including PVP hydrogel and polymeric microspheres is still in the development process.

Effective Targeting of Colon Cancer Cells with Piperine Natural Anticancer Prodrug Using Functionalized Clusters of Hydroxyapatite Nanoparticles.

Targeted drug delivery offers great opportunities for treating cancer. Here, we developed a novel anticancer targeted delivery system for piperine (Pip), an alkaloid prodrug derived from black pepper that exhibits anticancer effects. The tailored delivery system comprises aggregated hydroxyapatite nanoparticles (HAPs) functionalized with phosphonate groups (HAP-Ps). Pip was loaded into HAPs and HAP-Ps at pH 7.2 and 9.3 to obtain nanoformulations. The nanoformulations were characterized using several techniques and the release kinetics and anticancer effects investigated in vitro. The Pip loading capacity was >20%. Prolonged release was observed with kinetics dependent on pH, surface modification, and coating. The nanoformulations fully inhibited monolayer HCT116 colon cancer cells compared to Caco2 colon cancer and MCF7 breast cancer cells after 72 h, whereas free Pip had a weaker effect. The nanoformulations inhibited ~60% in HCT116 spheroids compared to free Pip. The Pip-loaded nanoparticles were also coated with gum Arabic and functionalized with folic acid as a targeting ligand. These functionalized nanoformulations had the lowest cytotoxicity towards normal WI-38 fibroblast cells. These preliminary findings suggest that the targeted delivery system comprising HAP aggregates loaded with Pip, coated with gum Arabic, and functionalized with folic acid are a potentially efficient agent against colon cancer.

Three-dimensional nanofibrous polystyrene scaffolds modify macrophage phenotypes and activate macrophage angiogenic potential.

3D scaffolds represent an attractive substrate for studying macrophage activation and modification since they mimic extracellular matrix (ECM). However, macrophage response to such materials, particularly with respect to angiogenic potential is still poorly recognized. Therefore, we investigated the effect of 3D nanofibrous polystyrene scaffolds (NPSs) versus tissue culture polystyrene (TCPS) on THP-1-derived macrophages in various environmental conditions, for example, standard (m0), pro-inflammatory (m1), or anti-inflammatory (m2) with respect to pro-angiogenic potential. There were no differences in the expression of TNF-α and IL-10 mRNAs and respective proteins in cells cultured on NPSs compared with flat polystyrene (TCPS), however, NPSs induced an increased VEGF production by macrophages cultured in m0 and m1 media. Cells cultured in m1, and m2 conditions secreted elevated amounts of TNF-α and IL-10, respectively, irrespective of substrate surface geometry. Each macrophage population contains large, medium, and small cells. Moreover, there were significant differences in the proportion of large to small macrophages depending on the medium composition, that is, in m0, m1, and m2 media these proportions were 1:4, 1:3, and 1:10, respectively. The ultrastructure and the immunoexpression of TNF-α and IL-10 were analyzed under a confocal microscope. The results demonstrated differences in cell ultrastructure and suggested that the larger cells were pro-inflammatory macrophages, while the smaller cells were anti-inflammatory macrophages. In conclusion, NPSs activate macrophage pro-angiogenic potential. In addition, an increase in the proportion of pro-inflammatory macrophages relative to anti-inflammatory ones in a given population favors this potential.

Lecithin suspensions for electrophoretic deposition on stainless steel coatings.

Lecithin is a mixture of phospholipids (PLs) that are found in living organisms. It gained the interest as a bio- and hemocompatible modifying agent for biomaterials. In this paper, we focused on the elaboration of a simple and well-described technology of metals coating with low-cost substance that could be useful in biomaterials industry. We studied the utility of lecithin suspension for stainless steel coating by electrophoretic deposition method. Our goal was to find a relationship between the conditions of lecithin suspension preparation, obtained suspension properties (vesicles size and structure, zeta potential, electrophoretic mobility) and lecithin coating features (topography, roughness). We found that final pH value, zeta potential and electrophoretic mobility of lecithin suspensions were not altered by initial solution pH value. However, the presence of hydrated Na+ ions forced forming of large multi-layered vesicles. We obtained uniform lecithin coatings with the use of electrophoretic deposition, which has a great potential to be used in a large scale.

Folic acid-conjugated mesoporous silica particles as nanocarriers of natural prodrugs for cancer targeting and antioxidant action.

Naturally derived prodrugs have a wide range of pharmacological activities, including anticancer, antioxidant, and antiviral effects. However, significant barriers inhibit their use in medicine, e.g. their hydrophobicity. In this comprehensive study, we investigated simple and effective nanoformulations consisting of amine-functionalized and conjugated with folic acid (FA) mesoporous silica nanoparticles (MSNs). Two types of MSNs were studied: KCC- 1, with mean size 324 nm and mean pore diameter 3.4 nm, and MCM - 41, with mean size 197 and pore diameter 2 nm. Both types of MSNs were loaded with three anticancer prodrugs: curcumin, quercetin, and colchicine. The nanoformulations were tested to target in vitro human hepatocellular carcinoma cells (HepG2) and HeLa cancer cells. The amine-functionalized and FA-conjugated curcumin-loaded, especially KCC-1 MSNs penetrated all cells organs and steadily released curcumin. The FA-conjugated MSNs displayed higher cellular uptake, sustained intracellular release, and cytotoxicity effects in comparison to non-conjugated MSNs. The KCC-1 type MSNs carrying curcumin displayed the highest anticancer activity. Apoptosis was induced through specific signaling molecular pathways (caspase-3, H2O2, c-MET, and MCL-1). The nanoformulations displayed also an enhanced antioxidant activity compared to the pure forms of the prodrugs, and the effect depended on the time of release, type of MSN, prodrug, and assay used. FA-conjugated MSNs carrying curcumin and other safe natural prodrugs offer new possibilities for targeted cancer therapy.

Electropolymerized hydrophilic coating on stainless steel for biomedical applications.

Current metal implants (e.g. stents) covered with drug-eluting coatings are not robust for long-term usage. Other types and methods of coatings are needed, especially ones that are not prone to activity loss in vivo. In this paper, the method of stainless steel (SS) coating with poly(ethylene glycol) dimethacrylate (PEGDMA) with the use of electropolymerization (EP) is presented. The application of a specific and simple reaction mixture enabled the production of SS-PEGDMA materials that possessed a homogenous surface. The polymer coating was durable for 28 days of constant washing. The resulting materials were non-toxic and haemolysis did not occur after incubation with blood. Moreover, because the coating filled up scratches present on bare SS and hydrophilized the SS surface, it reduced fibrinogen adsorption five times in comparison to SS and, unlike on SS, no platelet activation was detected. The presented method is a very promising candidate for scale up due to its simplicity and low cost.

IN VIVO PERFORMANCE OF THE EXPERIMENTAL CHITOSAN BASED BONE SUBSTITUTE--ADVANCED THERAPY MEDICINAL PRODUCT. A STUDY IN SHEEP.

When evaluating a novel bone substitute material, advanced in vivo testing is an important step in development and safety affirmation. Sheep seems to be a valuable model for human bone turnover and remodeling activity. The experimental material composed with the stem cells is an advanced therapy medicinal product (acc. to EC Regulation 1394/2007). Our research focuses on histological differences in bone formation (guided bone regeneration--GBR) in sheep maxillas after implantation of the new chitosan/tricalcium phosphate/alginate (CH/TCP/Alg) biomaterial in comparison to the commercially available xenogenic bone graft and a/m enhanced with the stem cells isolated from the adipose tissue. Twelve adult female sheep of BCP synthetic line, weighing 60-70 kg were used for the study. The 11 mm diameter defects in maxilla bone were prepared with a trephine bur under general anesthesia and then filled with the bone substitute materials: CH/TCP/Alg, BioOss Collagen, Geistlich AG (BO), CH/TCP/Alg composed with the stem cells (CH/S) or left just with the blood clot (BC). Inbreeding cycle of the animals terminated at 4 months after surgery. Dissected specimens of the maxilla were evaluated histologically and preliminary under microtomography. Histological evaluation showed early new bone formation observed around the experimental biomaterial and commercially available BO. There were no features of purulent inflammation and necrosis, or granulomatous inflammation. Microscopic examination after 4 months following the surgery revealed trabecular bone formation around chitosan based bone graft and xenogenic material with no significant inflammatory response. Different results--no bone recreation were observed for the negative control (BC). In conclusion, the tested materials (CH/TCP/Alg and BO) showed a high degree of biocompatibility and some osteoconductivity in comparison with the control group. Although the handiness, granules size and setting time of CHffCP/Alg may be refined for future clinical tests. The relevant beneficial influence of using the adipose derived stem cells in GBR was not confirmed in this model.