Vibration-Assisted Welding of 42CrMo4 Steel: Optimizing Parameters for Improved Properties and Weldability.

This study advances the vibration-assisted welding (VAW) technique for joining medium-carbon, low-alloy steels, which are typically challenging to weld. Traditional welding methods suggest low linear energy and mandatory pre- and post-heating due to these steels' poor weldability. However, VAW employs a vibrating table to maintain part vibration throughout the automatic MIG/MAG welding process. This study tested the VAW technique on 42CrMo4 steel samples, achieving satisfactory weld quality without the need for pre- and post-heating treatments. This research revealed that while vibration frequencies between 550 Hz and 9.5 kHz minimally affect the appearance of the weld joint, the oscillation acceleration has a significant impact. The acceleration along the weld axis (ax), combined with the welding speed and vibration frequency, affects the weld surface's appearance, particularly its scaly texture and size. Lateral acceleration (ay) alters the seam width, whereas vertical acceleration (az) affects penetration depth at the root. Notably, if the effective acceleration (aef) surpasses 40 m/s2, there is a risk of molten metal expulsion from the weld pool or piercing at the joint's base. The quality of the joints was assessed through macroscopic and microscopic structural analyses, micro-hardness tests in the weld zone, and bending trials. The mechanical properties of the VAW samples were found to be acceptable, with hardness slightly exceeding that of the samples subjected to pre- and post-heating. Moreover, the VAW process significantly reduced energy consumption and operational time. The employed vibration system, with a power rating of 100 W, operates for just a few minutes, resulting in substantially lower energy usage compared to the traditional pre- and post-heating method, which typically requires a 5 kW electric furnace.

Functional Surfaces via Laser Processing in Nickel Acetate Solution.

This study presents a novel laser processing technique in a liquid media to enhance the surface mechanical properties of a material, by thermal impact and micro-alloying at the subsurface level. An aqueous solution of nickel acetate (15% wt.) was used as liquid media for laser processing of C45E steel. A pulsed laser TRUMPH Truepulse 556 coupled to a PRECITEC 200 mm focal length optical system, manipulated by a robotic arm, was employed for the under-liquid micro-processing. The study's novelty lies in the diffusion of nickel in the C45E steel samples, resulting from the addition of nickel acetate to the liquid media. Micro-alloying and phase transformation were achieved up to a 30 µm depth from the surface. The laser micro-processed surface morphology was analysed using optical and scanning electron microscopy. Energy dispersive spectroscopy and X-ray diffraction were used to determine the chemical composition and structural development, respectively. The microstructure refinement was observed, along with the development of nickel-rich compounds at the subsurface level, contributing to an improvement of the micro and nanoscale hardness and elastic modulus (230 GPa). The laser-treated surface exhibited an enhancement of microhardness from 250 to 660 HV0.03 and an improvement of more than 50% in corrosion rate.

Morphological Analysis of Laser Surface Texturing Effect on AISI 430 Stainless Steel.

Laser surface texturing (LST) is a method to obtain micro-structures on the material's surface for improving tribological performances, wetting tuning, surface treatment, and increasing adhesion. The material selected for LST is AISI 430 ferritic stainless steel, distinguished by the low cost in manufacturing, corrosion resistance, and high strength at elevated temperature. The present study addresses the morphology of new pattern designs (crater array, ellipse, and octagonal shapes). The patterns are applied on the stainless-steel surface by a non-contact method with high quality and precision nanosecond pulsed laser equipment. The investigation of laser parameter influence on thermal affected area and micro-structures is accomplished by morphological and elemental analysis (SEM + EDX). The parameters of the laser micro-patterning have a marked influence on the morphology, creating groove-type sections with different depths and recast material features. From the SEM characterization, the highest level of recast material is observed for concentric octagon LST design. Its application is more recommended for the preparation of the metal surface before hybrid welding. Additionally, the lack of the oxygen element in the case of this design suggests the possible use of the pattern in hybrid joining.

Wettability and Surface Roughness Analysis of Laser Surface Texturing of AISI 430 Stainless Steel.

Due to its wide applicability in industry, devising microstructures on the surface of materials can be easily implemented and automated in technological processes. Laser Surface Texturing (LST) is applied to modify the chemical composition, morphology, and roughness of surfaces (wettability), cleaning (remove contaminants), reducing internal stresses of metals (hardening, tempering), surface energy (polymers, metals), increasing the adhesion (hybrid joining, bioengineering) and decreasing the growth of pathogenic bacteria (bioengineering). This paper is a continuation and extension of our previous studies in laser-assisted texturing of surfaces. Three different patterns (crater array-type C, two ellipses at 90° overlapping with its mirror-type B and 3 concentric octagons-type A) were applied with a nanosecond pulsed laser (active medium Nd: Fiber Diode-pumped) on the surface of a ferritic stainless steel (AISI 430). Micro texturing the surface of a material can modify its wettability behavior. A hydrophobic surface (contact angle greater than 90°) was obtained with different variations depending on the parameters. The analysis performed in this research (surface roughness, wettability) is critical for assessing the surface functionality, characteristics and properties of the stainless steel surface after the LST process. The values of the surface roughness and the contact angle are directly proportional to the number of repetitions and inversely proportional to the speed. Recommendations for the use of different texturing pattern designs are also made.