A three-dimensional algorithm for precise measurement of human auricle parameters.

Measurement of auricle parameters for planning and post-operative evaluation presents substantial challenges due to the complex 3D structure of the human auricle. Traditional measurement methods rely on manual techniques, resulting in limited precision. This study introduces a novel automated surface-based three-dimensional measurement method for quantifying human auricle parameters. The method was applied to virtual auricles reconstructed from Computed Tomography (CT) scans of a cadaver head and subsequent measurement of important clinically relevant aesthetical auricular parameters (length, width, protrusion, position, auriculocephalic angle, and inclination angle). Reference measurements were done manually (using a caliper and using a 3D landmarking method) and measurement precision was compared to the automated method. The CT scans were performed using both a contemporary high-end and a low-end CT scanner. Scans were conducted at a standard scanning dose, and at half the dose. The automatic method demonstrated significantly higher precision in measuring auricle parameters compared to manual methods. Compared to traditional manual measurements, precision improved for auricle length (9×), width (5×), protrusion (5×), Auriculocephalic Angle (5-54×) and posteroanterior position (23×). Concerning parameters without comparison with a manual method, the precision level of supero-inferior position was 0.489 mm; and the precisions of the inclination angle measurements were 1.365 mm and 0.237 mm for the two automated methods investigated. Improved precision of measuring auricle parameters was associated with using the high-end scanner. A higher dose was only associated with a higher precision for the left auricle length. The findings of this study emphasize the advantage of automated surface-based auricle measurements, showcasing improved precision compared to traditional methods. This novel algorithm has the potential to enhance auricle reconstruction and other applications in plastic surgery, offering a promising avenue for future research and clinical application.

Non-invasive quantitative assessment of induced component displacement can safely and accurately diagnose tibial component loosening in patients: A prospective diagnostic study.

PURPOSE: Aseptic loosening often requires major, expensive and invasive revision surgery. Current diagnostic modalities merely show indirect signs of loosening. A recent proof of concept study proposed a non-invasive technique for the quantitative and visual assessment of implant movement as a diagnostic aid for tibial component loosening. The primary research question addressed is whether this novel diagnostic modality can safely and effectively aid the diagnosis of aseptic loosening. METHODS: This clinical study included patients suspected of aseptic total knee arthroplasty (TKA) loosening listed for revision surgery and asymptomatic patients. Safety was evaluated using a numerical rating scale (NRS) for discomfort and by registration of adverse events. Feasibility was assessed by recording the duration and ease of the procedure. Intra- and interrater reliability were evaluated. In symptomatic patients, diagnostic accuracy metrics were evaluated with intra-operative assessment as a reference test. RESULTS: In total, 34 symptomatic and 38 asymptomatic knees with a TKA were analysed. The median NRS for discomfort during loading was 6 (interquartile range [IQR]: 3.75-7.00) in symptomatic patients and 2 (IQR: 1.00-3.00) in asymptomatic patients. No adverse events were reported. The majority of users found the use of the loading device easy. The median time spent in the computed tomography room was 9 min (IQR: 8.00-11.00). Excellent to good intra- and interrater reliabilities were achieved. Diagnostic accuracy analysis resulted in a sensitivity of 0.91 (95% confidence interval [CI]: 0.72-0.97) and a specificity of 0.72 (95% CI: 0.43-0.90). CONCLUSIONS: The proposed diagnostic method is safe, feasible, reliable and accurate in aiding the diagnosis of aseptic tibial component loosening. LEVEL OF EVIDENCE: Level II.

Promising results of an non-invasive measurement of knee implant loosening using a loading device, CT-scans and 3D image analysis.

BACKGROUND: After total knee arthroplasty up to 13% requires revision surgery to address loosening. No current diagnostic modalities have a sensitivity or specificity higher than 70-80% to detect loosening, leading to 20-30% of patients undergoing unnecessary, risky and expensive revision surgery. A reliable imaging modality is required to diagnose loosening. This study presents a new and non-invasive method and evaluates its reproducibility and reliability in a cadaveric study. METHODS: Ten cadaveric specimens were implanted with a loosely fitted tibial components and CT scanned under load towards valgus and varus using a loading device. Advanced three-dimensional imaging software was used to quantify displacement. Subsequently, the implants were fixed to the bone and scanned to determine the differences between the fixed and the loose state. Reproducibility errors were quantified using a frozen specimen in which displacement was absent. FINDINGS: Reproducibility errors, expressed as mean target registration error, screw-axis rotation and maximum total point motion were 0.073 mm (SD 0.033), 0.129 degrees (SD 0.039) and 0.116 mm (SD 0.031), respectively. In the loose condition, all displacements and rotation changes were larger than the reported reproducibility errors. Comparing the mean target registration error, screw axis rotation and maximum total point motion in the loose condition to the fixed condition resulted in mean differences of 0.463 mm (SD 0.279; p = 0.001), 1.769 degrees (SD 0.868; p < 0.001) and 1.339 mm (SD 0.712; p < 0.001), respectively. INTERPRETATION: The results of this cadaveric study show that this non-invasive method is reproducible and reliable for detection of displacement differences between fixed and loose tibial components.

Kinematic analysis of forearm rotation using four-dimensional computed tomography.

This study aimed to quantify forearm kinematics with a focus on the forearm rotation axis. Ten healthy volunteers were included in the study. One three-dimensional computed tomographic scan and two four-dimensional computed tomographic scans were done in all the arms to capture forearm joint motion. After image processing, the rotation axis and the movement of the radius with respect to various axes were quantified. The rotation axis was calculated using finite helical axis analysis and a circle fitting approach. The mean error of the rotation axis found through circle fitting was 0.2 mm (SD 0.1) distally and 0.1 mm (SD 0.1) proximally, indicating an improvement in precision over the finite helical axis approach. The translations of the radius along the ulnar axis and the forearm rotation axis were 2.6 (SD 0.8) and 0.6 mm (SD 0.9), respectively. The rotation of the radius around the radial axis was 7.2°. The techniques presented provide a detailed description of forearm kinematics.

Comparison of an oblique single cut rotation osteotomy with a novel 3D computer-assisted oblique double cut alignment approach.

An oblique double-cut rotation osteotomy (ODCRO) enables correcting a complex bone deformation by aligning, in 3D, the distal, middle and proximal bone segments with a target bone, without intersegmental gaps. We propose virtual preoperative planning of an ODCRO. To minimize a residual translation error, we use an optimization algorithm and optimize towards bone length, alignment in the transverse direction, or a balanced reconstruction. We compare the residual alignment error with an oblique single-cut rotation osteotomy using 15 complex bone deformations. The single-cut approach was not feasible in 5 cases, whereas the ODCRO procedure was feasible in all cases. The residual alignment error was smaller for the ODCRO than for the single-cut approach except for one case. In a subset for length reconstruction, the length error of 7.3-21.3 mm was restored to 0.0 mm in 4 of 5 cases, although at the cost of an increased transverse translation. The proposed method renders planning an ODCRO feasible and helps restoring bone alignment and lengthening better than an oblique single-cut rotation osteotomy. Awareness of the challenges and possibilities in preoperative planning of an ODCRO will be of value for future alignment surgery and for patients.

Carpal Kinematics in Madelung Deformity.

PURPOSE: Various skeletal and soft tissue abnormalities have been identified in Madelung deformity and have been hypothesized to play a causal role in its progressive symptomatology; however, our pathological understanding of these changes remains limited. In this study, we biomechanically assessed the Madelung deformity wrist, using 4-dimensional computed tomography imaging. METHODS: Nine Madelung deformity wrists (5 patients; age, 24 ± 5 y) and 18 healthy wrists (9 volunteers; age, 28 ± 3 y) underwent 4-dimensional imaging during flexion-extension motion and radioulnar deviation. Carpal kinematics and radiocarpal joint parameters were quantified and compared. RESULTS: In Madelung deformity wrists, significantly decreased rotation was seen in the lunate (-4.6°) and the triquetrum (-4.8°) during flexion-extension motion. During radioulnar deviation, significant decreases were visible in lunate bone translation (-0.7 mm), triquetrum bone translation (-0.6 mm), and triquetrum bone rotation (-1.9°). Patients had significantly decreased articulating surface areas of the scaphoid (1.4 ± 0.2 cm2 versus 1.6 ± 0.2 cm2) and lunate (1.2 ± 0.4 cm2 versus 1.5 ± 0.3 cm2) fossa, and significantly increased radioscaphoid (1.3 ± 0.1 mm versus 1.2 ± 0.1 mm) and radiolunate (1.6 ± 0.2 mm versus 1.3 ± 0.3 mm) joint space thicknesses. CONCLUSIONS: There is a decreased mobility of the lunate and triquetrum bones in Madelung deformity. CLINICAL RELEVANCE: Four-dimensional imaging could be used in future studies that investigate the effect of surgical ligament release on carpal kinematics and subsequent wrist mobility.

Patient-specific plate for navigation and fixation of the distal radius: a case series.

PURPOSE: Corrective osteotomy of a malunited distal radius conventionally relies on 2D imaging techniques for alignment planning and evaluation. However, this approach results in suboptimal bone repositioning, which is associated with poor patient outcomes. In this case series, we evaluate the use of novel patient-specific plates (PSPs), which feature navigation and fixation of bone segments as preoperatively planned in 3D. METHODS: Ten participants with distal radius malunion underwent CT scans for preoperative alignment planning. Patient-specific guides and plates were designed, 3D-printed, and sterilized for use in corrective surgery of the distal radius. Pre- and postoperative results were compared in regard to clinical, functional, and radiographic outcomes. RESULTS: The application of a PSP was successful in 7 of the 10 cases. After treatment, the residual alignment error was reduced by approximately 50% compared with conventional treatment. The use of PSPs reduced pain significantly. Pre- and postoperative results were pooled and demonstrated significant correlations between: (1) pain and malpositioning, (2) the range of pro- and supination motion, the MHOQ score, the EQ-5D-5L score and dorsovolar angulation, and (3) MHOQ score and proximodistal translation. CONCLUSION: The correlation between malalignment and MHOQ score, EQ-5D-5L score, pain, and range of motion shows that alignment should be restored as well as possible. Compared to the conventional approach, which relies on 2D imaging techniques, corrective osteotomy based on 3D preoperative planning and intraoperative fixation with a PSP has been shown to improve bone alignment and reduce pain. LEVEL OF EVIDENCE: IV.

Expression and Retention of Thymidine Phosphorylase in Cultured Reticulocytes as a Novel Treatment for MNGIE.

Mitochondrial neurogastrointestinal encephalomyopathy (MNGIE) is a rare autosomal metabolic disorder caused by thymidine phosphorylase (TP) deficiency. Successful therapeutic interventions for this disease rely on a means for efficient and long-lasting circulation of the TP enzyme. In this study we exploit lentiviral transduction of hematopoietic stem cells and an erythroid cell line (BEL-A) to generate reticulocytes that contain active TP. Significant loss of overexpressed TP during erythroid differentiation can be reduced by addition of the ubiquitination inhibitor MG132. However, the ubiquitination sites are located in the substrate binding site in human TP, and their removal abolished enzyme activity. Examination of the TP structure and mechanism suggested that these sites are only exposed in the absence of substrate. We show that supplementation of culture media with thymidine during differentiation reduces enzyme degradation, doubling the amount of TP retained in reticulocytes. This study provides proof of principle that therapeutic reticulocytes expressing TP can be generated in vitro and that ubiquitin-mediated degradation can be subverted through masking ubiquitination sites to ensure retention of human TP in reticulocytes following erythroid differentiation.

Computer-Assisted Techniques in Corrective Distal Radius Osteotomy Procedures.

Malunion of the distal radius is a common complication following a distal radius fracture. The surgical treatment of a symptomatic distal radius malunion is a corrective osteotomy (CO) procedure aimed at the restoration of the anatomical alignment of the distal radius articular surface in the wrist joint. Traditional two-dimensional imaging techniques in the management of malunion have demonstrated to be limited in pre-, intra-, and postoperative imaging and visualization of the bone architecture. Over the past decades, with the advent of three-dimensional (3-D) imaging techniques, innovations have emerged in the field of preoperative planning, navigation, and 3-D printing. The aim of this paper is to review the existing literature and inform clinicians and biomedical engineers approaching the field about advantages, disadvantages, and future perspectives of existing computer-assisted technology for CO. Collected studies agree on showing the efficacy of the computed-tomography-based 3-D virtual planning. Currently, patient-specific 3-D printed guides and implants are the most promising technology to transfer the preoperative plan to the patient. However, further biomechanical studies, larger clinical trials, and a major exposure of clinicians to 3-D planning are needed to augment the feasibility of using these technologies in standard practice.

Quantitative three-dimensional assessment of Madelung deformity.

In the diagnostic work-up of Madelung deformity conventional radiographic imaging is often used, assessing the three-dimensional deformity in a two-dimensional manner. A three-dimensional approach could expand our understanding of Madelung deformity's complex wrist anatomy, while removing inter- and intra-rater differences. We measured previous two-dimensional-based and newly developed three-dimensional-based parameters in 18 patients with Madelung deformity (28 wrists) and 35 healthy participants (56 wrists). Madelung deformity wrists have increased levels of ulnar tilt, lunate subsidence, lunate fossa angle, and palmar carpal displacement. The lunate fossa is more concave and irregular, and angles between scaphoid, lunate, and triquetral bones are decreased. These findings validate the underlying principles of current two-dimensional criteria and reveal previously unknown anatomical abnormalities by utilizing novel three-dimensional parameters to quantify the radiocarpal joint.

Carpal kinematic changes after scaphoid nonunion: an in vivo study with four-dimensional CT imaging.

The aim was to evaluate if motion between the scaphoid bone fragments is related to the position of the fracture line and if a scaphoid nonunion results in the uncoupling of the proximal and distal carpal row during wrist motion. The influence of dorsal intercalated segment instability on interfragmentary motion was also analysed. In this study, 12 patients were included with unilateral scaphoid nonunion. Four-dimensional computerized tomography was used to analyse flexion-extension and radioulnar deviation motion of both wrists. We found that an increased instability of the scaphoid fragments is associated with the presence of dorsal intercalated segment instability and is not dependent on the position of the fracture line relative to the scaphoid apex. Additionally, a scaphoid nonunion results in an uncoupling of the carpal rows.

A four-dimensional-CT study of in vivo scapholunate rotation axes: possible implications for scapholunate ligament reconstruction.

Additional fixation of the palmar scapholunate interosseous ligament has been advocated to improve the long-term results of dorsal scapholunate interosseous ligament reconstruction. To investigate the validity of this approach, we determined normal scapholunate motion patterns and calculated the location of the scapholunate rotation axis. We hypothesized that the optimal location of the scapholunate interosseous ligament insertion could be determined from the scapholunate rotation axis. Four-dimensional computerized tomography was used to study the wrist motion in 21 healthy participants. During flexion-extension motions, the scaphoid rotates 38° (SD 0.6°) relative to the lunate; the rotation axis intersects the dorsal ridge of the proximal pole of the scaphoid and the dorsal ridge of the lunate. Minimal scapholunate motion is present during radioulnar deviation. Since the scapholunate rotation axis runs through the dorsal proximal pole of the scaphoid, this is probably the optimal location for attaching the scapholunate ligament during reconstructive surgery.

Surgical Management of Madelung Deformity: A Systematic Review.

Background: Madelung deformity is a congenital wrist condition characterized by volar subluxation of the wrist caused by premature growth arrest of the distal radius. Progressive symptoms can necessitate surgical intervention, yet optimal treatment strategy remains unknown. The aim of this study is to determine treatment options, surgical indications, and operative outcomes for Madelung deformity. Methods: This study adhered to the Meta-Analyses of Observational Studies in Epidemiology (MOOSE) guidelines. A comprehensive systematic review was performed to identify all studies describing surgical interventions for Madelung deformity. All studies were evaluated by level of evidence and a self-developed quality assessment tool. Results: Twenty-five studies met inclusion criteria; all case series with type IV level of evidence. Studies assessed pain, range of motion, aesthetic deformity, and grip strength. The primary indication for surgery was the presence of wrist pain. Various surgical procedures exist and could be categorized as radial lengthening, ulnar shortening, or a combination of both. All studies report postoperative pain reduction and most studies report an improved range of motion. Conclusions: A variety of surgical procedures reportedly have satisfactory outcomes. However, outcomes are reported in an inconsistent manner, prohibiting pooling of studies and comparisons of surgical procedures and their outcomes. We propose several methodological changes for implementation in future studies, increasing the quality of evidence to compensate for small patient numbers.

Positioning accuracy of a patient-tailored rimmed wedge implant for corrective osteotomy of the distal radius.

Conventional corrective osteotomy surgery is based on 2-D imaging for planning and evaluation of bone positioning. In this feasibility study we propose and evaluate the use of 3-D preoperative planning and design of a custom rimmed wedge to be inserted into the osteotomy gap. The shape of the wedge provides 3-D bone positioning as planned, while the rims keep the bone segments in place. The method is evaluated experimentally using 3-D printed radii specimens of five different malunion patients, as well as in a human cadaver specimen. Positioning was accurate and reproducible showing residual displacements along the x-, y- and z-axes of (mean ± SD): (-0.19 ± 0.75, 0.38 ± 1.09, and 0.47 ± 0.48) mm and residual rotations about these axes of (mean ± SD): (-1.22 ± 1.66, -0.40 ± 0.93, and -0.33 ± 1.50)° for artificial bone specimens. The cadaver experiment showed similar displacements along the x-, y- and z-axes (-0.17, 1.11, and -0.35) mm and residual rotations about these axes (-2.93, -1.53, and 2.31)°. Positioning by inserting a rimmed wedge in corrective osteotomy surgery is accurate with residual errors comparable to bilateral differences. The method seems promising for future utilization in corrective osteotomy surgery and may ultimately render the procedure minimally invasive.

Minimizing the Translation Error in the Application of an Oblique Single-Cut Rotation Osteotomy: Where to Cut?

OBJECTIVE: An oblique single cut rotation osteotomy enables correcting angular bone alignment in the coronal, sagittal, and transverse planes, with just a single oblique osteotomy, and by rotating one bone segment in the osteotomy plane. However, translational malalignment is likely to exist if the bone is curved or deformed and the location of the oblique osteotomy is not obvious. METHODS: In this paper, we investigate how translational malalignment depends on the osteotomy location. We further propose and evaluate by simulation in 3-D, a method that minimizes translational malalignment by varying the osteotomy location and by sliding the distal bone segment with respect to the proximal bone segment within the oblique osteotomy plane. The method is finally compared to what three surgeons achieve by manually selecting the osteotomy location in 3-D virtual space without planning in-plane translations. RESULTS: The minimization method optimized for length better than the surgeons did, by 3.2 mm on average, range (0.1, 9.4) mm, in 82% of the cases. A better translation in the axial plane was achieved by 4.1 mm on average, range (0.3, 14.4) mm, in 77% of the cases. CONCLUSION: The proposed method generally performs better than subjectively choosing an osteotomy position along the bone axis. SIGNIFICANCE: The proposed method is considered a valuable tool for future alignment planning of an oblique single-cut rotation osteotomy since it helps minimizing translational malalignment.

Estimating Scaphoid Lengths Using Anatomical Measurements in the Wrist.

PURPOSE: In reconstructive surgery of scaphoid nonunions with humpback deformity, some surgeons recommend restoration of the normal scaphoid length whereas others overexpand the normal length to ensure carpal realignment and prevent late collapse. To be able to define overexpansion and investigate which levels of overexpansion yield optimal clinical results, a precise method for estimating the original scaphoid length is required. The purpose of this anatomic study was to investigate the precision of estimating normal scaphoid lengths based on intact adjacent bone dimensions, compared with using the contralateral scaphoid length. METHODS: From bilateral computed tomographic scans of 28 healthy wrist pairs, 3-dimensional virtual bone models were created. The left and right scaphoid lengths were determined at the central axis. The capitate length at the central axis and the distal radius width served to derive an ipsilateral scaphoid length estimate. Estimation precision for individual cases was based on the 95% range (±1.96 × SD) of the observed differences between the actual and estimated lengths. RESULTS: On average, the capitate length was 10% smaller than the scaphoid length; the radius width was 9% larger. Consequently, we averaged the capitate length and radius width for ipsilateral estimations. The average difference between the scaphoid length and the latter ipsilateral estimate was 0.1 mm. The average contralateral scaphoid length difference was also 0.1 mm. Estimation precisions, however, were ±2.2 and ±1.4 mm, respectively. CONCLUSIONS: Scaphoid length estimation based on the contralateral scaphoid is more precise than the estimating scaphoid length using the ipsilateral radius and capitate. CLINICAL RELEVANCE: Scaphoid overexpansion can be ensured if the restored length is at least 1.4 mm longer than the contralateral length. This may be valuable information when establishing a target length for reconstruction and investigating the consequences of scaphoid overexpansion on clinical function, such as range of motion, which are currently unknown.

Three-Dimensional Assessment of Bilateral Symmetry of the Scaphoid: An Anatomic Study.

Preoperative 3D CT imaging techniques provide displacement analysis of the distal scaphoid fragment in 3D space, using the matched opposite scaphoid as reference. Its accuracy depends on the presence of anatomical bilateral symmetry, which has not been investigated yet using similar techniques. Our purpose was to investigate symmetry by comparing the relative positions of distal and proximal poles between sides. We used bilateral CT scans of 19 adult healthy volunteers to obtain 3D scaphoid models. Left proximal and distal poles were matched to corresponding mirrored right sides. The left-to-right positional differences between poles were quantified in terms of three translational and three rotational parameters. The mean (SD) of ulnar, dorsal, and distal translational differences of distal poles relative to proximal poles was 0.1 (0.6); 0.4 (1.2); 0.2 (0.6) mm and that of palmar rotation, ulnar deviation, and pronation differences was -1.1 (4.9); -1.5 (3.3); 1.0 (3.7)°, respectively. These differences did not significantly differ from zero and thus were not biased to left or right side. We proved that, on average, the articular surfaces of scaphoid poles were symmetrically aligned in 3D space. This suggests that the contralateral scaphoid can serve as reference in corrective surgery. No level of evidence is available.

Quantifying scaphoid malalignment based upon height-to-length ratios obtained by 3-dimensional computed tomography.

PURPOSE: To determine if 3-dimensional height-to-length (H/L) measurements including coronal plane assessment will improve malalignment detection of scaphoid fractures and to determine if more waist than proximal pole nonunions are malaligned. METHODS: Computed tomography scans of uninjured wrists (n = 74) were used to obtain 3-dimensional models of healthy scaphoids. These models were used to determine 95% normal ranges of the H/L ratio in standard sagittal and coronal planes in an automated fashion. Subsequently, the H/L ratios of fibrous nonunions (n = 26) were compared with these normal ranges and were classified as either aligned or malaligned. RESULTS: The mean normal H/L ratio in the sagittal plane was 0.61 (range, 0.54-0.69) and in the coronal plane 0.42 (range, 0.36-0.48). The mean H/L ratios of the nonunions differed from those of the healthy scaphoids in these planes: 0.65 and 0.48, respectively. Based on sagittal plane evaluation of all nonunions, 46% exceeded the normal H/L range versus 54% based on combining sagittal and coronal plane measurements. More waist nonunions (71%) than proximal pole nonunions (22%) exceed the normal H/L range. CONCLUSIONS: Evaluation of the H/L ratio in the coronal plane provided valuable additional information for the detection of scaphoid deformities. More malaligned cases were found for waist nonunions than for proximal pole nonunions. CLINICAL RELEVANCE: This method may be a helpful diagnostic tool to detect malalignment and to choose between in situ fixation or reconstruction.