Enhanced photocatalytic degradation of amoxicillin using a spinning disc photocatalytic reactor (SDPR) with a novel Fe3O4@void@CuO/ZnO yolk-shell thin film nanostructure.

Antibiotics are resistant compounds with low biological degradation that generally cannot be removed by conventional wastewater treatment processes. The use of yolk-shell nanostructures in spinning disc photocatalytic reactor (SDPR) enhances the removal efficiency due to their high surface-to-volume ratio and increased interaction between catalyst particles and reactants. The purpose of this study is to investigate the SDPR equipped to Fe3O4@void@CuO/ZnO yolk-shell thin film nanostructure (FCZ YS) in the presence of visible light illumination in the photocatalytic degradation of amoxicillin (AMX) from aqueous solutions. Stober, co-precipitation, and self-transformation methods were used for the synthesis of FCZ YS thin film nanostructure and the physical and chemical characteristics of the catalyst were analyzed by XRD, VSM,, EDX, FESEM, TEM, AFM, BET, contact angle (CA), and DRS. Then, the effect of different parameters including pH (3-11), initial concentration of AMX (10-50 mg/L), flow rate (10-25 mL/s) and rotational speed (100-400 rpm) at different times in the photocatalytic degradation of AMX were studied. The obtained results indicated that the highest degradation efficiency of 97.6% and constant reaction rate of AMX were obtained under LED visible light illumination and optimal conditions of pH = 5, initial AMX concentration of 30 mg/L, solution flow rate of 15 mL/s, rotational speed of 300 rpm and illumination time of 80 min. The durability and reusability of the nanostructure were tested, that after 5 runs had a suitable degradation rate. Considering the appropriate efficiency of amoxicillin degradation by FCZ YS nanostructure, the use of Fe3O4@void@CuO/ZnO thin film in SDPR is suggested in water and wastewater treatment processes.

Utilization of the copper recovered from waste printed circuit boards as a metal precursor for the synthesis of TiO2/magnetic-MOF(Cu) nanocomposite: Application in photocatalytic degradation of pesticides in aquatic solutions.

In this study, a number of leaching solutions (H2SO4, CuSO4 and NaCl) and an electrochemical method were used together for the separation of Cu from waste printed circuit boards. Secondly, the magnetic-MOF(Cu) was synthesized using the Cu recovered from waste printed circuit boards. Thereafter, TiO2/mag-MOF(Cu) composite was prepared and its photocatalytic activity was assessed in the photo degradation of two prominent organophosphorus pesticides, namely malathion (MTN) and diazinon (DZN). The catalytic structure of the MOF-based composite was fully characterized by various analyses such as XRD, SEM, EDAX, FT-IR, VSM and UV-vis. The obtained analyses confirmed the successful synthesis of TiO2/mag-MOF(Cu) composite. The synthesized composite exhibited highly efficient in the degradation of both pollutants under the following conditions: pH 7, contaminant concentration 1 mg/L, the catalyst dosage of 0.4 g/L, visible light intensity 75 mW/cm2 and reaction time of 45 min. First order kinetic model was best suited with the experimental results (R2: 0.97-0.99 for different MTN and DZN concentrations). Trapping studies revealed that superoxide radicals (O2•-) played an important role during the degradation process. Furthermore, the catalyst demonstrated a superb recovery as well as high stability over five cyclic runs of reuse. In addition, the total organic carbon (TOC) analysis showed over 83% and 85% mineralization for MTN and DZN, respectively. The combined system of TiO2/mag-MOF(Cu)/Vis also exhibited a great level of efficiency and feasibility in the treatment of tap water and treated wastewater samples. It is concluded that TiO2/mag-MOF(Cu) could be used as an excellent catalyst for the photodegradation of MTN and DZN in aqueous solution.

Benzo (a) pyrene in infant foods: a systematic review, meta-analysis, and health risk assessment.

Exposure of infants to chemicals during their development will have major effects on their health. One of the major exposures of infants to chemicals is through their food. The main structure of infant food is milk, which is high in fat. There is a possibility of accumulation of environmental pollution, including benzo (a) pyrene (BaP). In this systematic review, the amount of BaP in infant milk was surveyed for this purpose. The chosen keywords were: benzo (a) pyrene, BaP, Infant formula, dried milk, powdered milk, and baby food. A total of 46 manuscripts were found in the scientific database. After initial screening and quality assessment, 12 articles were selected for extraction of data. By meta-analysis, the total estimate of BaP in baby food was calculated to be 0.078 ± 0.006 µg/kg. Estimation of daily intake (EDI) and Hazard Quotient (HQ) for noncarcinogenic risk and Margin of exposure (MOE) for carcinogenic risk were also calculated for three age groups 0-6 months, 6-12 months, and 1-3 years. HQ was lower than 1 and MOE was more than 10,000 for three age groups. Therefore, there is no potential carcinogenic and non-carcinogenic risk for infant health.

Investigation of photocatalytic-proxone process performance in the degradation of toluene and ethyl benzene from polluted air.

In this study, toluene and ethylbenzene were degraded in the photocatalytic-proxone process using BiOI@NH2-MIL125(Ti)/Zeolite nanocomposite. The simultaneous presence of ozone and hydrogen peroxide is known as the proxone process. Nanocomposite Synthesis was carried out using the solvothermal method. Inlet airflow, ozone concentrations, H2O2 concentrations, relative humidity, and initial pollutants concentrations were studied. The nanocomposite was successfully synthesized based on FT-IR, BET, XRD, FESEM, EDS element mapping, UV-Vis spectra and TEM analysis. A flow rate of 0.1 L min-1, 0.3 mg min-1 of ozone, 150 ppm of hydrogen peroxide, 45% relative humidity, and 50 ppmv of pollutants were found to be optimal operating conditions. Both pollutants were degraded in excess of 95% under these conditions. For toluene and ethylbenzene, the synergistic of mechanisms effect coefficients were 1.56 and 1.76, respectively. It remained above 95% efficiency 7 times in the hybrid process and had good stability. Photocatalytic-proxone processes were evaluated for stability over 180 min. The remaining ozone levels in the process was insignificant (0.01 mg min-1). The CO2 and CO production in the photocatalytic-proxone process were 58.4, 5.7 ppm for toluene and 53.7, and 5.5 ppm for ethylbenzene respectively. Oxygen gas promoted and nitrogen gas had an inhibitory effect on the effective removal of pollutants. During the pollutants oxidation, various organic intermediates were identified.

Association Between Non-alcoholic Fatty Liver Disease and Heavy Metal Exposure: a Systematic Review.

Non-alcoholic fatty liver disease (NAFLD) is a debilitating disease with adverse effects including cirrhosis and hepatocellular carcinoma. Heavy metals can cause severe dysfunction in different body organs including the liver. This review offers the study regarding the positive or negative association between heavy metals exposure and non-alcoholic fatty liver disease. The method used in this study is a systematic review based on searching in the PubMed, Scopus, and Science direct databases with the keywords of fatty liver, non-alcohol fatty liver, heavy metal, mercury, cadmium, arsenic, chromium, thallium, lead, iron, zinc, and nickel. There were 2200 articles searched in databases, and after assessment, 28 articles were selected. Positive association is established between arsenic, cadmium, iron, lead, mercury, and fatty liver disease. A negative relationship is found between zinc, copper, and progressive fatty liver disease. Furthermore, laboratory methods for NAFLD diagnosis were examined according to the obtained manuscripts. Among the different diagnostic methods, magnetic resonance imaging (MRI) is a sensitive method.

Clean environment index: A new approach for litter assessment.

Littered waste is one of the ubiquitous problems in urban environments. In this study, urban environmental pollution was evaluated for the first time using a new developed index. The findings indicated that cigarette butts with an average 58% are the largest share in the composition of littered waste. In addition, the numbers of littered wastes throughout the study area had a spatial variation. According to clean environment index (CEI), the entire study area was found to be in a moderate status. However, 40% of the study areas were classified in a dirty and extremely dirty status. Comparison of the studied urban land-uses showed that residential land use with CEI equal to 3.38 is interpreted in the clean status, while commercial land use with CEI equal to 15.05 can be classified in the dirty status. The application of CEI has a good capability to assess littered waste; this index can be employed to evaluate the pollution of urban sidewalks and other environments such as beaches.

Preparation of a cellulose acetate membrane using cigarette butt recycling and investigation of its efficiency in removing heavy metals from aqueous solution.

This study investigated the recycling of freshly-smoked cigarette butts (FCBs) and unsmoked cigarette filters (UCFs) into a cellulose acetate (CA) membrane. The both samples were prepared by means of a combination of seven cigarette brands, and the phase inversion method was used to recycle each sample into a membrane using N-methyl-2-pyrrolidone. The efficiency of the prepared membranes for the removal of chromium, cadmium, and lead from an aqueous solution in a forward osmosis reactor was investigated. The results showed that the both membranes had a smooth surface and macrovoids. The flux of the prepared membranes from the UCFs and FCBs recycling were 14.8 and 13.2 LMH, respectively. The porosity and reverse salt of the UCFs membrane were 61% and 3.5 gMH, while those for FCBs membrane were 58% and 3.9 gMH. The observed metal removal efficiency of the both membranes was in the range of 85 to 90%. However, increasing the concentration of metals up to five times caused a slight decrease in the removal efficiency (less than 5%).

Synthesis of BiOI@NH2-MIL125(Ti)/Zeolite as a novel MOF and advanced hybrid oxidation process application in benzene removal from polluted air stream.

One of the popular process in volatile organic compounds removal in gas phase is advanced oxidation process. We in this research, synthesized BiOI@NH2-MIL125(Ti)/Zeolite nanocomposite as a novel nanocomposite to degradation of benzene in hybrid advanced oxidation process. The nanocomposite synthesized via solvothermal method. The effect of airflow, ozone gas concentration, hydrogen peroxide concentration, relative humidity and initial benzene concentration are the main parameters in the UV/O3/H2O2/ nanocomposite hybrid process that were studied. The characterization by XRD, FT-IR, FESEM, EDS element mapping, TEM, BET, and UV-vis spectra indicated that nanocomposite were well synthesized. Optimal operating conditions of the process were determined at air flow of 0.1 l/min, ozone concentration of 0.3 mg/min, hydrogen peroxide concentration of 150 ppm, relative humidity of 45 ± 3% and benzene concentration of 50 ppmv. Under these conditions, more than 99% of benzene was degraded. The synergistic effect coefficient of the mechanisms is 1.53. The nanocomposite had good stability in the hybrid process and remained above 99% efficiency up to 5 times. The ozone concentration residual the system was reported to be negligible (0.013 mg/min). The CO and CO2 emissions in the hybrid process was higher than other processes, which indicates better mineralization in the hybrid process. Formaldehyde, octane, noonan, phenol, decanoic acid were reported as the main by-products. The results indicated that UV/O3/H2O2/ nanocomposite hybrid process has fantastic efficiency in the degradation of benzene as one of the indicators of VOCs.

Bio-electrical stimulation process on degradation of Phenanthrene from aqueous solution using a novel anode modified with carbon cloth: Operational performance, microbial activity and energy.

Phenanthrene as the hazardous PAHs-component are extensively detected in industrial wastewater. However, the impacts of bioelectrostimulation process on Phenanthrene degradation in aerobic reactors remained unclear. Here, a novel bioelectrostimulation process equipped with carbon cloth as electrodes was developed to investigate the removal efficiency of Phenanthrene and ATPase enzyme activity in the synthetic wastewater. The results obtained from the present study indicated that a complete Phenanthrene degradation (100%) can be achieved using microbial electrostimulation systems steel mesh coated with carbon cloth (MES-CC) as anode under optimal operational conditions (electrical current: 4 mA, HA concentration: 15 mg L-1) within 18 h. The conductive carbon cloth provides a biofilm carrier to easily transfer the electrons between electrodes and microbial communities. In addition, the highest ATPase enzyme activity (5176 U) was observed when the aerobic MES-CC reactors were operated with electrical current 4 mA. Furthermore, the COD removal efficiency in MES-CC increased from 49% to 96% when the C: N ratio decreased from 20 to 5. The highest value of Vmax in MES-CC for suspended and attached growth were determined to be 2.87 and 0.54 g COD g-1 biomass. Overall, the results demonstrated that MES equipped with carbon cloth and continuous electrical current mode has good potential for efficient Phenanthrene wastewater treatment.

Risk assessment of heavy metals consumption through onion on human health in Iran.

Considering the importance of onions consumption in the household diet, controlling of heavy elements' concentration in foodstuffs is important to ensure the safety of an individual's health. This study aimed to evaluate the risk of heavy metals through onion consumption on human health. In this cross-sectional experimental study, 22 onion samples with varieties red, yellow, and white in the two autumn and winter seasons in 2020 were randomly collected from the different provinces of Kurdistan, Hamedan, and Kermanshah. The concentrations of heavy metals were evaluated with an atomic absorption spectrometer. The risks of human health were evaluated by the hazard quotient (HQ) and the obtained results were analyzed with one-way ANOVA and one sample t-test. The obtained findings demonstrated that all collected samples contained heavy metals. For example, the cadmium (Cd) concentration in onion samples in the province of West Azerbaijan, Kurdistan, Hormozgan, Isfahan, and Zanjan was 526.49, 274.49, 69.77, 67.39, 65.69 µg kg-1, respectively. While the standard specified in Iran for the concentration of Cd in onions is 50 µg kg-1. However, the rate of lead (Pb) contamination in samples collected from Isfahan, Hormozgan, Zanjan Khuzestan, Tehran (Varamin) was 296.50, 266.71, 261.49, 215.64, 106.19 µg kg-1, respectively, which less than maximum allowable limit recommended by WHO-FAO (300 µg kg-1). The HQ for non-cancerous diseases for Cd and Pb were 8.6 × 10-2 and 1.6 × 10-1, respectively, and the probability of carcinogenic risk for Pb (8.1 × 10-4) was at the level of acceptable. There is no concern about the non-carcinogenic diseases and carcinogenic risk of consuming heavy metals in onion. Therefore, for optimal management and prevention of further pollution, it is recommended to study the origin and determine the amounts of heavy metals for their potential contamination of foodstuffs from the region's soil, water, and dust.

Emission of BTEX compounds from the frying process: Quantification, environmental effects, and probabilistic health risk assessment.

Frying is one of the cooking methods which generates mono aromatic hydrocarbons, including benzene, toluene, ethylbenzene, and xylene (BTEX); subsequently, it affects health through carcinogenic (CR) and non-carcinogenic risks (n-CR). However, their environmental effects known by secondary organic aerosols (SOA) and ozone formation potential (OFP) were also attended by many scientists. Therefore, this study quantified the BTEX emissions from 4 types of most commonly used edible oils (canola, corn, sunflower, and blend) under various frying conditions of temperatures and food additives. Furthermore, the effects of the chemicals in the light of health (CR and n-CR) and environment (SOA and OFP) were also investigated. The study results showed that higher temperatures could significantly increase the emissions, while the addition of food ingredients significantly reduces the emissions. The rank order of emitted chemical was obtained as T > B > E > X. The blend had the most emission among oils, followed by, in descending order, corn, sunflower, and canola. In association with environmental effects, the orders of X > T > E > B and T âˆ¼ E > X > B were obtained for OFP and SOA, respectively. THQ for blend, corn, canola, and sunflower oils was higher than 1 (1.76, 1.35, 1.27, and 1.002, respectively), showing a considerable n-CR when the hood was off. In this respect, TCR for the oils (1.78 × 10-4, 1.45 × 10-4, 1.39 × 10-4, and 1.05 × 10-4, respectively) shown the probable risk for all oils. Moreover, hood switching reduced the risk by about 11-81%.

Synthesis of pH-sensitive hyaluronic acid nanogels loaded with paclitaxel and interferon gamma: Characterization and effect on the A549 lung carcinoma cell line.

Lung cancer is one of the deadliest cancers in various populations. Apart from the effects that anticancer drugs such as paclitaxel (PTX) have on cancer cells, they also have many side effects on healthy cells. Interferon gamma (IFN-γ) is also one of the cytokines used in the treatment of cancer. Current research is focused on providing new drug carriers to find new therapeutic goals. After synthesis of nanogels and loading of PTX and IFN-γ, the cytotoxicity of these nanogels on A549 and HEK293 healthy cell line was measured by MTT assay and flow cytometry analysis. Finally, the expression of STAT1 gene was investigated using Real time-PCR. The results of MTT assay showed that the survival rate of healthy cells treated with PTX and IFN-γ-loaded nanogels was 2.15 and 2.39 times higher than cancer cells, respectively. The results also showed that the gene expression STAT1 in A549 cells exposed to these nanogels was higher than healthy cells (p < 0.05). Based on flow cytometry results, the death rate of healthy cells treated with the mentioned nanogels was lower than cancer cells (p < 0.05). Therefore, Studies showed that synthesized nanogels have positive effects on cancer cells and also have fewer side effects on healthy cells.

Assessment of littered cigarette butt in urban environment, using of new cigarette butt pollution index (CBPI).

Cigarette butts (CBs) are hazardous wastes usually littered by smokers and are of the prevalence wastes in the environment. Although various studies have been done regarding the quantity of CBs on the coast, few studies have been conducted on its density and distribution in urban areas. Therefore, the objective of this study was to assess the quantity and distribution of CBs in urban areas to define an index to convert the results into comparable data in various conditions and cities. The data were obtained by visual surveys using field CB counts in the summer of 2019 in the city of Qazvin, Iran. Cigarette butt pollution index (CBPI) was defined by considering CB density, weather conditions, urban characteristics including the structure of the walkways, and distance from groundwater. The findings indicated that the average cigarette butts density in urban areas were found to be in range of 0.01 and 0.51. Spatial variation of CB was observed in the city due to urban characteristics like land use, differences in municipal services, and population density. The CBPI index calculated for a park showed the highest number whereas an administrative (official) area had the lowest CBPI of 0.15. Given the significant pollution of the city studied with CBs and the proper performance of CBPI in classifying various parts of the city, using this method and index can be a good way to assess CBs in the streets of most of the cities.

A global systematic review, meta-analysis and health risk assessment on the quantity of Malathion, Diazinon and Chlorpyrifos in Vegetables.

It is widely believed that an increasing trend in the production and consumption of vegetables has led to a dramatic rise in the use of pesticides potentially threatening the health of consumers around the world. This systematic study along with meta-analysis has mainly centered on the evaluation of the quantity of three well-known pesticides namely, Malathion (MLT), Diazinon (DZN) and Chlorpyrifos (CPF) in vegetables. In this regard, a comprehensive literature search has been performed over the last decade (January 1, 2011 to June 21, 2020) within the scientific databases including PubMed, Web of Science, and Scopus. Of 1239 articles identified through the database screening, 22 plus 37 data report were retained and included in the meta-analysis phase. Additionally, the probabilistic human health risks for the consumers due to the intake of CPF, DZN and MLT from eating vegetables were estimated by the Monte Carlo Simulated (MCS) method. According to the findings, the maximum quantities of MLT, DZN and CPF in the vegetables were observed in Pakistan (222 µg/kg, 95%CI = 214.94-229.08), Thailand (245.00, 95% CI = 235.2-254.8) and South Korea (440 µg/kg, 95% CI = 437.19-442.81), while the lowest concentration levels were reported in China (1.7 µg/kg, 95% CI = 1.56-1.84), Poland (0.57, 95% CI = 0.46-0.68) and Poland (5.78 µg/kg, 95% CI = 4.40-7.12), respectively. The results of the Egger's and the Begg's tests revealed that no bias with regard to the potential publication was observed. Finally, non-carcinogenic risk assessment results demonstrated that the exposure to the studied pesticides thorough vegetables consumption could not threaten the health of consumers.

Microextraction on a screw for determination of trace amounts of hexanal and heptanal as lung cancer biomarkers.

Solid phase microextraction on a screw was utilized for the extraction of hexanal and heptanal as lung cancer biomarkers from urine samples. Reduced graphene oxide (rGO) was coated on the surface of a stainless-steel set screw by electrophoretic deposition method. The screw was located inside a glass cover, and the created channel acted as the sample solution flow pass. A 5 mL glass syringe was connected to a syringe pump to direct the sample and the eluent through the channel. The extraction procedure was followed by gas chromatography/mass spectrometry (GC/MS) for separation and determination of the extracted aldehydes. The effective parameters on the extraction efficiencies of the analytes were identified and optimized. Under the optimal extraction conditions, the extraction time was as short as 10 min. The calibration curves indicated good linearity (R2 > 0.97) within the concentration range of 1.0-50 µg L-1. The obtained limits of detection (LODs) for hexanal and heptanal were down to 0.4 and 0.3 µg L-1, respectively. Considering the repeatability, simplicity, and eco-friendliness of this simple extraction method, it can be efficiently used for preconcentration of aldehydes in different samples.

Assess the annual effective dose and contribute to risk of lung cancer caused by internal radon 222 in 22 regions of Tehran, Iran using geographic information system.

Radon gas is one of the most influential sources of indoor exposure. All its physical properties together make it a significant risk factor for lung cancer in the population. The research aims are outlined as (1) to measure the radon concentration in Tehran city and compare results with the international standards (2) to determine spatial distribution of radon gas concentration using Geographical Information System (GIS) software and (3) to estimate the annual effective dose and potential risk of lung cancer by radon-222 in Tehran city. In this study, 800 Alpha Track detectors were installed in houses in 22 regions of Tehran city and retrieved after 3 months. The measurements were repeated for spring and summer and autumn seasons. The annual effective dose and risk of lung cancer were assessed using standard equations. Data were analyzed using SPSS 20. Result showed the minimum and maximum radon concentration were observed in and Ghalee-kobra (0.13 Bq.m-3) and Charbagh-ponak district (661.11 Bq.m-3) respectively. There was no observed relationship between radon concentration and houses' model, cracking condition and constructionn materials. Expectedly, the storehouses and basements had significantly higher (P = 0.016) radon concentration than occupied rooms. The min and max of the estimated annual effective dose were 0.65 and 2.03 mSv, respectively. Result showed that around 5% of the sampling sites had higher level of radon than the maximum allowed by EPA. A rough estimation of the expected radon-attributed lung cancer incidences yielded approximately 5958 cases in the total population of Tehran every year. In view of the growing trend in cancer incidences, appropriate measures addressing radon should be undertaken in areas of increased exposure to this noble gas.

Littered cigarette butt as a well-known hazardous waste: A comprehensive systematic review.

Most of cigarettes used in the world have filters. Following smoking, the cigarette butts (CBs) are often littered as wastes in the environment. CBs generally contain several toxic substances that are trapped in the cigarette filter. Filters are made of non-biodegradable materials and remain in the environment for a long time. Within this study, it is attempted to systematically review the articles on CBs and find out the answers to the problems associated with the factors including quantity, distribution, origin and toxicity of CBs in the environment. It is estimated that approximately 5.5 trillion cigarettes are being produced annually in the world and the CB wastes would reach 1.2 million tons and increase by 50% until 2025. CBs contain thousands of dangerous chemicals such as arsenic, benzene, hydrogen cyanide, PAHs, pyridine, heavy metals and so forth. It is also believed that eachCB can pollute 1000 liters of water. Given the inadequacy of mechanical equipment as well as the cost of collecting these wastes, there should be a special focus on these items as follows: producing cigarettes with degradable filters, reducing the rate of smoking in the world, reducing the toxic and chemical substances in the process of plant growth, processing and production of cigarettes, training people to discard CBs properly, putting legal and financial pressures on cigarettes production, and the last but not least, providing effective solutions for collecting CBs.

Carbon fibers modified with polypyrrole for headspace solid phase microextraction of trace amounts of 2-pentyl furan from breath samples.

This study introduces micrometric carbon strands as a suitable fiber for headspace solid phase microextraction. Compared to previous supports, carbon fibers have mechanical flexibility, wide thermal expansion, and a large surface area, which is an important factor in headspace solid phase microextraction. The electrophoretic technique was applied to modify the surface of stainless steel and carbon fibers with polypyrrole. Modified carbon fibers were used for extraction of 2-pentylfuran (2-PF) as a model analyte from patients' breath and coffee samples. 2-PF belongs to the furan family, which was suggested as a biomarker for Aspergillus fumigatus and was classified as a possible carcinogen. 2-PF can be found in many heat-processed foods and drinks. The separation and detection of the analyte was performed by gas chromatography coupled to mass spectrometry. The effective factors in the extraction performance of the analyte by carbon fiber supports were investigated and optimized. Under optimized extraction conditions (temperature, 20 °C; time, 15 min; desorption temperature, 200 °C; desorption time, 2 min; salt concentration, 10% w/v; and stirring rate, 700 rpm), the limit of detection was calculated as 0.05 ng mL-1, whereas repeatability and fiber-to-fiber reproducibility (RSD %) was found to be in the range of 3.2-4.1%. The experimental results showed that the proposed fiber had greater extraction performance for 2-pentylfuran.

Retinol and α-Tocopherol Levels in the Serum and Subcutaneous Adipose Tissue of Newly Diagnosed Basal Cell Carcinoma Patients.

BACKGROUND: Nonmelanoma skin cancers are the most frequently occurring skin cancers. Vitamin A is involved in epithelial cell differentiation and may control skin tumor development. Vitamin E is a powerful lipophilic antioxidant that can quench and scavenge reactive oxygen species. However, there is little consistent evidence considering micronutrients and the development of basal cell carcinoma (BCC). Therefore, we aimed to investigate the possible difference between retinol and α-tocopherol in BCC patients and controls in Iranian population. METHODS: This case-control study was conducted on adults with newly diagnosed BCC referred to Razi Hospital, Tehran, Iran in 2015. Serum and subcutaneous fat tissue retinol and α-tochopherol were measured by HPLC method. RESULTS: Overall, serum retinol level was lower significantly in BCC patients (0.237±0.01 µg/ml) in comparison with control group (0.27±0.02 µg/ml, P-value: 0.038). However serum α-tocopherol level was not significantly different between BCC patients (4.41±0.33 µg/ml) and control subjects (4.06±0.35 µg/ml, P-value=0.18). Sub-cutaneous adipose tissue retinol was lower significantly in BCC patients (38.60±3.30 ng/mg) compared with control group (54.78±3.49 ng/mg, P-value=0.002). Furthermore, results revealed lower subcutaneous adipose tissue α-tocopherol in BCC patients (4.41±0.33 µg/ml) in comparison with control group (4.06±0.35 µg/ml, P-value=0.18). CONCLUSION: Skin tissue concentration of retinol and α-tocopherol and serum retinol level was lower in BCC patients in comparison with control group but serum α-tocopherol was not different between groups.

Preparation of Carbon-Alumina (C/Al2O3) aerogel nanocomposite for benzene adsorption from flow gas in fixed bed reactor.

Benzene is one of the hazardous environmental pollutants which have harmful effects on human, animal and environmental health. the goal of this study was to synthesize a carbon/alumina aerogel with large surface area, which is easily recoverable and can be used as an adsorbent for benzene removal from the polluted air flow. The composite aerogel was dried at ambient temperature for 48 h and at 120 °C for 48 h in a sequential way. The characteristic properties of the composite aerogel were analyzed using Brunauer-Emmett-Teller (BET), Scanning Electron Microscopy (SEM), Barrett-Joyner-Halenda (BJH) method and energy-dispersive X-Ray (EDX) techniques. The findings of this study showed that, with increasing of the inlet flow rate from 0.2 l/min to 0.5 and 0.8 l/min, the breakthrough time decreased from 13 h to 7 and 3 h, respectively., Besides, the amount of adsorption capacity on aerogel nanocomposite decreased from 126.73 mg g-1 to 84.5 and 38 mgg-1 with increasing the inlet benzene concentration from 100 ppmv to 200 and 300 ppmv, respectively. In addition, the a carbon/alumina aerogel can be exploited for removing other pollutants from air and water. Recently, the adsorption process has attracted many research attentions for Benzene removal from different applications due to some inherent characteristics such as low-cost and high feasibility. •The results indicated that the synthesis of the composite aerogel have been successfully performed.•The composite aerogel was synthesized by combining Novollac with alumina, which had high surface area and suitable benzene adsorption ability.