Antifouling Properties of Dendritic Polyglycerols against Marine Macrofouling Organisms.

Dendritic polyglycerols (PGs) were synthesized and postmodified by grafting of poly(ethylene glycol) (PEG) and polypropylene glycol (PPG) diglycidyl ether groups, and their antifouling and fouling-release properties were tested. Coating characterization by spectroscopic ellipsometry, contact angle goniometry, attenuated total internal reflection-Fourier transform infrared spectroscopy (ATR-FTIR), and atomic force microscopy showed brushlike morphologies with a high degree of microscale roughness and the ability to absorb large amounts of water within seconds. PGs with three different thicknesses were tested in laboratory assays against settlement of larvae of the barnacle Balanus improvisus and against the settlement and removal of zoospores of the alga Ulva linza. Very low coating thicknesses, e.g., 11 nm, reduced the settlement of barnacles, under static conditions, to 2% compared with 55% for an octadecyltrichlorosilane reference surface. In contrast, zoospores of U. linza settled readily but the vast majority were removed by exposure to a shear force of 52 Pa. Both PEG and PPG modification increased the antifouling properties of the PG films, providing a direct comparison of the ultralow fouling properties of all three polymers. Both, the modified and the nonmodified PGs are promising components for incorporation into amphiphilic fouling-resistant coatings.

Fouling-Release Performance of Silicone Oil-Modified Siloxane-Polyurethane Coatings.

The effect of incorporation of silicone oils into a siloxane-polyurethane fouling-release coatings system was explored. Incorporation of phenylmethyl silicone oil has been shown to improve the fouling-release performance of silicone-based fouling-release coatings through increased interfacial slippage. The extent of improvement is highly dependent upon the type and composition of silicone oil used. The siloxane-polyurethane (SiPU) coating system is a tough fouling-release solution, which combines the mechanical durability of polyurethane while maintaining comparable fouling-release performance with regard to commercial standards. To further improve the fouling-release performance of the siloxane-PU coating system, the use of phenylmethyl silicones oils was studied. Coatings formulations were prepared incorporating phenylmethyl silicone oils having a range of compositions and viscosities. Contact angle and surface energy measurements were conducted to evaluate the surface wettability of the coatings. X-ray photoelectron spectroscopy (XPS) depth profiling experiments demonstrated self-stratification of silicone oil along with siloxane to the coating-air interface. Several coating formulations displayed improved or comparable fouling-release performance to commercial standards during laboratory biological assay tests for microalgae (Navicula incerta), macroalgae (Ulva linza), adult barnacles (Balanus amphitrite syn. Amphibalanus amphitrite), and mussels (Geukensia demissa). Selected silicone-oil-modified siloxane-PU coatings also demonstrated comparable fouling-release performance in field immersion trials. In general, modifying the siloxane-PU fouling-release coatings with a small amount (1-5 wt % basis) of phenylmethyl silicone oil resulted in improved performance in several laboratory biological assays and in long-term field immersion assessments.

A novel biofilm channel for evaluating the adhesion of diatoms to non-biocidal coatings.

Laboratory assessment of the adhesion of diatoms to non-toxic fouling-release coatings has tended to focus on single cells rather than the more complex state of a biofilm. A novel culture system based on open channel flow with adjustable bed shear stress values (0-2.4 Pa) has been used to produce biofilms of Navicula incerta. Biofilm development on glass and polydimethylsiloxane elastomer (PDMSe) showed a biphasic relationship with bed shear stress, which was characterised by regions of biofilm stability and instability reflecting cohesion between cells relative to the adhesion to the substratum. On glass, a critical shear stress of 1.3-1.4 Pa prevented biofilm development, whereas on PDMS, biofilms continued to grow at 2.4 Pa. Studies of diatom biofilms cultured on zwitterionic coatings using a bed shear stress of 0.54 Pa showed lower biomass production and adhesion strength on poly(sulfobetaine methacrylate) compared to poly(carboxybetaine methacrylate). The dynamic biofilm approach provides additional information to supplement short duration laboratory evaluations.

Investigation of the role of hydrophilic chain length in amphiphilic perfluoropolyether/poly(ethylene glycol) networks: towards high-performance antifouling coatings.

The facile preparation of amphiphilic network coatings having a hydrophobic dimethacryloxy-functionalized perfluoropolyether (PFPE-DMA; M(w) = 1500 g mol(-1)) crosslinked with hydrophilic monomethacryloxy functionalized poly(ethylene glycol) macromonomers (PEG-MA; M(w) = 300, 475, 1100 g mol(-1)), intended as non-toxic high-performance marine coatings exhibiting antifouling characteristics is demonstrated. The PFPE-DMA was found to be miscible with the PEG-MA. Photo-cured blends of these materials containing 10 wt% of PEG-MA oligomers did not swell significantly in water. PFPE-DMA crosslinked with the highest molecular weight PEG oligomer (ie PEG1100) deterred settlement (attachment) of algal cells and cypris larvae of barnacles compared to a PFPE control coating. Dynamic mechanical analysis of these networks revealed a flexible material. Preferential segregation of the PEG segments at the polymer/air interface resulted in enhanced antifouling performance. The cured amphiphilic PFPE/PEG films showed decreased advancing and receding contact angles with increasing PEG chain length. In particular, the PFPE/PEG1100 network had a much lower advancing contact angle than static contact angle, suggesting that the PEG1100 segments diffuse to the polymer/water interface quickly. The preferential interfacial aggregation of the larger PEG segments enables the coating surface to have a substantially enhanced resistance to settlement of spores of the green seaweed Ulva, cells of the diatom Navicula and cypris larvae of the barnacle Balanus amphitrite as well as low adhesion of sporelings (young plants) of Ulva, adhesion being lower than to a polydimethyl elastomer, Silastic T2.

A general approach to controlling the surface composition of poly(ethylene oxide)-based block copolymers for antifouling coatings.

To control the surface properties of a polystyrene-block-poly(ethylene oxide) diblock copolymer, perfluorinated chemical moieties were specifically incorporated into the block copolymer backbone. A polystyrene-block-poly[(ethylene oxide)-stat-(allyl glycidyl ether)] [PS-b-P(EO-stat-AGE)] statistical diblock terpolymer was synthesized with varying incorporations of allyl glycidyl ether (AGE) in the poly(ethylene oxide) block from 0 to 17 mol %. The pendant alkenes of the AGE repeat units were subsequently functionalized by thiol-ene chemistry with 1H,1H,2H,2H-perfluorooctanethiol, yielding fluorocarbon-functionalized AGE (fAGE) repeat units. (1)H NMR spectroscopy and size-exclusion chromatography indicated well-defined structures with complete functionalization of the pendant alkenes. The surfaces of the polymer films were characterized after spray coating by X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine structure spectroscopy (NEXAFS), showing that the P(EO-stat-fAGE) block starts to compete with polystyrene to populate the surface after only 1 mol % incorporation of fAGE. Increasing the incorporation of fAGE led to an increased amount of perfluorocarbons on the surface and a decrease in the concentration of PS. At a fAGE incorporation of 8 mol %, PS was not detected at the surface, as measured by NEXAFS spectroscopy. Water contact angles measured by the captive-air-bubble technique showed the underwater surfaces to be dynamic, with advancing and receding contact angles varying by >20°. Protein adsorption studies demonstrated that the fluorinated surfaces effectively prevent nonspecific binding of proteins relative to an unmodified PS-b-PEO diblock copolymer. In biological systems, settlement of spores of the green macroalga Ulva was significantly lower for the fAGE-incorporated polymers compared to the unmodified diblock and a polydimethylsiloxane elastomer standard. Furthermore, the attachment strength of sporelings (young plants) of Ulva was also reduced for the fAGE-containing polymers, affirming their potential as fouling-release coatings.

The antifouling and fouling-release performance of hyperbranched fluoropolymer (HBFP)-poly(ethylene glycol) (PEG) composite coatings evaluated by adsorption of biomacromolecules and the green fouling alga Ulva.

Cross-linked hyperbranched fluoropolymer (HBFP) and poly(ethylene glycol) (PEG) amphiphilic networks with PEG weight percentages of 14% (HBFP-PEG14), 29% (HBFP-PEG29), 45% (HBFP-PEG45), and 55% (HBFP-PEG55) were prepared on 3-aminopropyl)triethoxysilane (3-APS) functionalized microscope glass slides for marine antifouling and fouling-release applications. The surface-free energies (gamma(s)), polar (gamma(s)(p) and gamma(s)(AB)), and dispersion (gamma(s)(d) and gamma(s)(LW)) components were evaluated using advancing contact angles by two-liquid geometric-mean and three-liquid Lifshitz-van der Waals acid-base approaches. The HBFP coating exhibited a low surface energy of 22 mJ/m(2), while the gamma(s) and gamma(s)(p) of the cross-linked HBFP-PEG coatings increased proportionally with the PEG weight percentages in the networks. The adsorption of bovine serum albumin (BSA), lectin from Codium fragile (CFL), lipopolysaccharides from Escherichia coli (LPSE) and Salmonella minnesota (LPSS) upon glass, APS-glass, HBFP, PEG, and the cross-linked HBFP-PEG network coatings were investigated by fluorescence microscopy. The marine antifouling and fouling-release properties of the cross-linked HBFP-PEG coatings were evaluated by settlement and release assays involving zoospores of green fouling alga Ulva (syn. Enteromorpha; Hayden, H. S.; Blomster, J.; Maggs, C. A.; Silva, P. C.; Stanhope, M. J.; Waaland, J. R. Eur. J. Phycol. 2003, 38, 277). The growth and release of Ulva sporelings were also investigated upon the HBFP-PEG45 coating in comparison to a poly(dimethylsiloxane) elastomer (PDMSE) standard material. Of the heterogeneous cross-linked network coatings, the maximum resistances to protein, lipopolysaccharide, and Ulva zoospore adhesion, as well as the best zoospore and sporeling release properties, were recorded for the HBFP-PEG45 coating. This material also exhibited better performance than did a standard PDMSE coating, suggesting its unique applicability in fouling-resistance applications.

Coatings based on side-chain ether-linked poly(ethylene glycol) and fluorocarbon polymers for the control of marine biofouling.

The preparation of side group modified polystyrene-based surface-active block copolymers (SABC) for use as marine fouling resistance/release applications is described. Modifying moieties such as poly(ethylene glycol) (PEG) and semifluorinated segments were used. A novel bilayer methodology has been employed that provides both suitable mechanical properties through the use of an elastomeric primer layer of styrene-ethylene/butylene-styrene (SEBS) and control of surface-chemistry through use of the SABCs. This approach has potential as a cost-effective technology for environmentally benign coatings that resist and release marine biofouling. Initial testing of these materials included determination of captive bubble contact angles and protein adsorption. Testing against marine fouling organisms was performed using settlement and adhesion bioassays with zoospores of the green alga Enteromorpha. The results showed that all surfaces had markedly reduced levels of zoospore settlement compared with glass controls and that adhesion strength was strongly affected by the semifluorinated SABC. The results are discussed in terms of surface properties.

Nickel removal from nickel plating waste water using a biologically active moving-bed sand filter.

Efficient removal of dissolved nickel was observed in a biologically active moving-bed 'MERESAFIN' sand filter treating rinsing water from an electroless nickel plating plant. Although nickel is fully soluble in this waste water, its passage through the sand filter promoted rapid removal of approximately 1 mg Ni/l. The speciation of Ni in the waste water was modelled; the most probable precipitates forming under the conditions in the filter were predicted using PHREEQC. Analyses of the Ni-containing biosludge using chemical, electron microscopical and X-ray spectroscopic techniques confirmed crystallisation of nickel phosphate as arupite (Ni3(PO4)2 x 8H2O), together with hydroxyapatite within the bacterial biofilm on the filter sand grains. Biosorption contributed less than 1% of the overall sequestered nickel. Metabolising bacteria are essential for the process; the definitive role of specific components of the mixed population is undefined but the increase in pH promoted by metabolic activity of some microbial components is likely to promote nickel desolubilisation by others.