Thermal treatment of municipal solid waste incineration fly ash: Impact of gas atmosphere on the volatility of major, minor, and trace elements.

Development of thermal processes for selective recovery of Zn and other valuable elements from municipal solid waste incineration (MSWI) fly ash requires comprehensive knowledge of the impact of gas atmosphere on the volatile behaviour of the element constituents of the ash at different reaction temperatures. This study assesses the partitioning of 18 elements (Al, As, Bi, C, Ca, Cd, Cl, Cu, K, Mg, Na, P, Pb, S, Sb, Sn, Ti, and Zn) between condensed and gaseous phases during thermal treatment of MSWI fly ash in both oxidising gas and reducing gas atmospheres, at different temperatures spanning the range 200-1050 °C. The operating atmosphere had major impacts on the partitioning of the following elements: As, Bi, C, Cd, Cu, Na, Pb, S, Sb, Sn, and Zn. The partitioning of these elements cannot be accurately predicted over the full range of investigated operating conditions with global thermodynamic equilibrium calculations alone, i.e. without also considering chemical kinetics and mass transfer. In oxidising conditions, the following elements were predominately retained in condensed phases, even at high temperatures: As, Bi, Sb, Sn, and Zn. All these elements, except As, were largely released to the gas phase (>70%) at high temperatures in reducing conditions. The impact of gas atmosphere on the volatility of Cd and Pb was greatest at low reaction temperatures (below ~750 °C). Results for volatile matrix elements, specifically C, Cl, K, Na, and S, are interpreted in terms of the mechanisms governing the release of these elements to the gas phase.

Volatilisation of major, minor, and trace elements during thermal processing of fly ashes from waste- and wood-fired power plants in oxidising and reducing gas atmospheres.

This study assesses the volatility of 15 elements (As, Bi, C, Cd, Cl, Cu, K, Mn, Na, P, Pb, S, Sb, Sn, and Zn) during thermal processing of fly ashes obtained from four waste-to-energy plants and one wood-combustion plant. Differences in volatility in oxidising and reducing atmospheres (air and 10% H2/90% N2) were assessed at two temperatures, 700 and 1000 °C. P and Mn were predominately retained in all ashes regardless of the operating atmosphere and temperature. Other elements showed significant variation in volatility depending on the type of fly ash, atmosphere, and temperature. Heat-treatment of the wood-combustion fly ash in the air atmosphere resulted in low release of K, Na, and all investigated heavy metals and metalloids. Several valuable elements, including Zn, Sb, Sn, and Bi, were significantly more volatile in the reducing atmosphere than in the oxidising atmosphere, particularly at 1000 °C. Other elements were either less volatile, equally volatile, or only marginally more volatile when the ashes were heated at 1000 °C in the reducing atmosphere. These elements include C, Cl, Cu, and, in the case of fly ashes derived from municipal solid waste, Cd and Pb. A two-step process, in which municipal solid waste incineration fly ash is first heated in an oxidising atmosphere and then in a reducing atmosphere, is proposed for production of a chloride-free zinc concentrate. Evaluation of the two-step process at 880 °C shows good potential for selective volatilisation of Zn with other valuable elements, including Sn, Sb, and Bi.

Impact of photochemical ageing on Polycyclic Aromatic Hydrocarbons (PAH) and oxygenated PAH (Oxy-PAH/OH-PAH) in logwood stove emissions.

The combustion of spruce logwood in a modern residential stove was found to emit polycyclic aromatic hydrocarbons (PAH) and oxygenated polycyclic aromatic hydrocarbons (OPAH) with emission factors of 404 µg MJ-1 of 35 analysed PAH, 317 µg MJ-1 of 11 analysed Oxy-PAH and 12.5 µg MJ-1 of 5 analysed OH-PAH, most of which are known as potential mutagens and carcinogens. Photochemical ageing in an oxidation flow reactor (OFR) degraded particle-bound PAH, which was also reflected in declining PAH toxicity equivalent (PAH-TEQ) values by 45 to 80% per equivalent day of photochemical ageing in the atmosphere. OPAH concentrations decreased less than PAH concentrations during photochemical ageing, supposedly due to their secondary formation, while 1-hydroxynaphthalene, 1,5-dihydroxynaphthalene and 1,8-naphthalaldehydic acid were significantly increased after ageing. Furthermore, secondary organic aerosol (SOA) formation and aromatic compounds not included in targeted analysis were investigated by thermal-optical carbon analysis (TOCA) hyphenate to resonance-enhanced multi-photon ionisation time-of-flight mass spectrometry (REMPI-TOFMS). The commonly used PAH-source indicators phenanthrene/anthracene, fluoranthene/pyrene, retene/chrysene, and indeno[cd]pyrene/benzo[ghi]perylene remained stable during photochemical ageing, enabling identification of wood combustion emissions in ambient air. On the other hand, benz[a]pyrene/benz[e]pyrene and benz[a]anthracene/chrysene were found to decrease with increasing photochemical age. Retene/chrysene was not a proper classifier for the wood combustion emissions of this study, possibly due to more efficient combustion than in open wood burning, from which this diagnostic ratio was initially derived. This study motivates in-depth investigation of degradation kinetics of particle-bound species on different combustion aerosol as well as the consequences of photochemical ageing on toxicity and identification of wood combustion emissions in ambient air.

Emissions from a fast-pyrolysis bio-oil fired boiler: Comparison of health-related characteristics of emissions from bio-oil, fossil oil and wood.

There is currently great interest in replacing fossil-oil with renewable fuels in energy production. Fast pyrolysis bio-oil (FPBO) made of lignocellulosic biomass is one such alternative to replace fossil oil, such as heavy fuel oil (HFO), in energy boilers. However, it is not known how this fuel change will alter the quantity and quality of emissions affecting human health. In this work, particulate emissions from a real-scale commercially operated FPBO boiler plant are characterized, including extensive physico-chemical and toxicological analyses. These are then compared to emission characteristics of heavy fuel-oil and wood fired boilers. Finally, the effects of the fuel choice on the emissions, their potential health effects and the requirements for flue gas cleaning in small-to medium-sized boiler units are discussed. The total suspended particulate matter and fine particulate matter (PM1) concentrations in FPBO boiler flue gases before filtration were higher than in HFO boilers and lower or on a level similar to wood-fired grate boilers. FPBO particles consisted mainly of ash species and contained less polycyclic aromatic hydrocarbons (PAH) and heavy metals than had previously been measured from HFO combustion. This feature was clearly reflected in the toxicological properties of FPBO particle emissions, which showed less acute toxicity effects on the cell line than HFO combustion particles. The electrostatic precipitator used in the boiler plant efficiently removed flue gas particles of all sizes. Only minor differences in the toxicological properties of particles upstream and downstream of the electrostatic precipitator were observed, when the same particulate mass from both situations was given to the cells.

Differences between co-cultures and monocultures in testing the toxicity of particulate matter derived from log wood and pellet combustion.

BACKGROUND: In vitro studies with monocultures of human alveolar cells shed deeper knowledge on the cellular mechanisms by which particulate matter (PM) causes toxicity, but cannot account for mitigating or aggravating effects of cell-cell interactions on PM toxicity. METHODS: We assessed inflammation, oxidative stress as well as cytotoxic and genotoxic effects induced by PM from the combustion of different types of wood logs and softwood pellets in three cell culture setups: two monocultures of either human macrophage-like cells or human alveolar epithelial cells, and a co-culture of these two cell lines. The adverse effects of the PM samples were compared between these setups. RESULTS: We detected clear differences in the endpoints between the mono- and co-cultures. Inflammatory responses were more diverse in the macrophage monoculture and the co-culture compared to the epithelial cells where only an increase of IL-8 was detected. The production of reactive oxygen species was the highest in epithelial cells and macrophages seemed to have protective effects against oxidative stress from the PM samples. With no metabolically active cells at the highest doses, the cytotoxic effects of the PM samples from the wood log combustion were far more pronounced in the macrophages and the co-culture than in the epithelial cells. All samples caused DNA damage in macrophages, whereas only beech and spruce log combustion samples caused DNA damage in epithelial cells. The organic content of the samples was mainly associated with cytotoxicity and DNA damage, while the metal content of the samples correlated with the induction of inflammatory responses. CONCLUSIONS: All of the tested PM samples induce adverse effects and the chemical composition of the samples determines which pathway of toxicity is induced. In vitro testing of the toxicity of combustion-derived PM in monocultures of one cell line, however, is inadequate to account for all the possible pathways of toxicity.

Nano-sized zinc oxide and silver, but not titanium dioxide, induce innate and adaptive immunity and antiviral response in differentiated THP-1 cells.

Nano-sized metal oxides are currently the most manufactured nanomaterials (NMs), and are increasingly used in consumer products. Recent exposure data reveal a genuine potential for adverse health outcomes for a vast array of NMs, however the underlying mechanisms are not fully understood. To elucidate size-related molecular effects, differentiated THP-1 cells were exposed to nano-sized materials (n-TiO2, n-ZnO and n-Ag), or their bulk-sized (b-ZnO and b-TiO2) or ionic (i-Ag) counterparts, and genome-wide gene expression changes were studied at low-toxic concentrations (<15% cytotoxicity). TiO2 materials were nontoxic in MTT assay, inducing only minor transcriptional changes. ZnO and Ag elicited dose-dependent cytotoxicity, wherein ionic and particulate effects were synergistic with respect to n-ZnO-induced cytotoxicity. In gene expression analyzes, 6 h and 24 h samples formed two separate hierarchical clusters. N-ZnO and n-Ag shared only 3.1% and 24.6% differentially expressed genes (DEGs) when compared to corresponding control. All particles, except TiO2, activated various metallothioneins. At 6 h, n-Zn, b-Zn and n-Ag induced various immunity related genes associating to pattern recognition (including toll-like receptor), macrophage maturation, inflammatory response (TNF and IL-1beta), chemotaxis (CXCL8) and leucocyte migration (CXCL2-3 and CXCL14). After 24 h exposure, especially n-Ag induced the expression of genes related to virus recognition and type I interferon responses. These results strongly suggest that in addition to ionic effects mediated by metallothioneins, n-Zn and n-Ag induce expression of genes involved in several innate and adaptive immunity associated pathways, which are known to play crucial role in immuno-regulation. This raises the concern of safe use of metal oxide and metal nanoparticle products, and their biological effects.

Inhalation and Oropharyngeal Aspiration Exposure to Rod-Like Carbon Nanotubes Induce Similar Airway Inflammation and Biological Responses in Mouse Lungs.

Carbon nanotubes (CNTs) have the potential to impact technological and industrial progress, but their production and use may, in some cases, cause serious health problems. Certain rod-shaped multiwalled CNTs (rCNTs) can, in fact, induce severe asbestos-like pathogenicity in mice, including granuloma formation, fibrosis, and even cancer. Evaluating the comparability between alternative hazard assessment methods is needed to ensure fast and reliable evaluation of the potentially adverse effects of these materials. To compare two alternative airway exposure methods, C57BL/6 mice were exposed to rCNTs by a state-of-the-art but laborious and expensive inhalation method (6.2-8.2 mg/m3, 4 h/day for 4 days) or by oropharyngeal aspiration (10 or 40 µg/day for 4 days), which is cheaper and easier to perform. In addition to histological and cytological studies, transcriptome analysis was also carried out on the lung tissue samples. Both inhalation and low-dose (10 µg/day) aspiration exposure to rCNTs promoted strong accumulation of eosinophils in the lungs and recruited also a few neutrophils and lymphocytes. In contrast, the aspiration of a high-dose (40 µg/day) rCNT caused only a mild pulmonary eosinophilia but enhanced accumulation of neutrophils in the airways. Inhalation and low-dose aspiration exposure promoted comparable giant cell formation, mucus production, and IL-13 expression in the lungs. Both exposure methods also exacerbated similar expression alterations with 154 (56.4%) differentially expressed, overlapping genes in microarray analyses. Of all differentially expressed genes, up to 80% of the activated biological functions were shared according to pathway enrichment analyses. Inhalation and low-dose aspiration elicited very similar pulmonary inflammation providing evidence that oropharyngeal aspiration is a valid approach and a convenient alternative to the inhalation exposure for the hazard assessment of nanomaterials.

Aerosol emissions of a ship diesel engine operated with diesel fuel or heavy fuel oil.

Gaseous and particulate emissions from a ship diesel research engine were elaborately analysed by a large assembly of measurement techniques. Applied methods comprised of offline and online approaches, yielding averaged chemical and physical data as well as time-resolved trends of combustion by-products. The engine was driven by two different fuels, a commonly used heavy fuel oil (HFO) and a standardised diesel fuel (DF). It was operated in a standardised cycle with a duration of 2 h. Chemical characterisation of organic species and elements revealed higher concentrations as well as a larger number of detected compounds for HFO operation for both gas phase and particulate matter. A noteworthy exception was the concentration of elemental carbon, which was higher in DF exhaust aerosol. This may prove crucial for the assessment and interpretation of biological response and impact via the exposure of human lung cell cultures, which was carried out in parallel to this study. Offline and online data hinted at the fact that most organic species in the aerosol are transferred from the fuel as unburned material. This is especially distinctive at low power operation of HFO, where low volatility structures are converted to the particulate phase. The results of this study give rise to the conclusion that a mere switching to sulphur-free fuel is not sufficient as remediation measure to reduce health and environmental effects of ship emissions.

Particulate matter from both heavy fuel oil and diesel fuel shipping emissions show strong biological effects on human lung cells at realistic and comparable in vitro exposure conditions.

BACKGROUND: Ship engine emissions are important with regard to lung and cardiovascular diseases especially in coastal regions worldwide. Known cellular responses to combustion particles include oxidative stress and inflammatory signalling. OBJECTIVES: To provide a molecular link between the chemical and physical characteristics of ship emission particles and the cellular responses they elicit and to identify potentially harmful fractions in shipping emission aerosols. METHODS: Through an air-liquid interface exposure system, we exposed human lung cells under realistic in vitro conditions to exhaust fumes from a ship engine running on either common heavy fuel oil (HFO) or cleaner-burning diesel fuel (DF). Advanced chemical analyses of the exhaust aerosols were combined with transcriptional, proteomic and metabolomic profiling including isotope labelling methods to characterise the lung cell responses. RESULTS: The HFO emissions contained high concentrations of toxic compounds such as metals and polycyclic aromatic hydrocarbon, and were higher in particle mass. These compounds were lower in DF emissions, which in turn had higher concentrations of elemental carbon ("soot"). Common cellular reactions included cellular stress responses and endocytosis. Reactions to HFO emissions were dominated by oxidative stress and inflammatory responses, whereas DF emissions induced generally a broader biological response than HFO emissions and affected essential cellular pathways such as energy metabolism, protein synthesis, and chromatin modification. CONCLUSIONS: Despite a lower content of known toxic compounds, combustion particles from the clean shipping fuel DF influenced several essential pathways of lung cell metabolism more strongly than particles from the unrefined fuel HFO. This might be attributable to a higher soot content in DF. Thus the role of diesel soot, which is a known carcinogen in acute air pollution-induced health effects should be further investigated. For the use of HFO and DF we recommend a reduction of carbonaceous soot in the ship emissions by implementation of filtration devices.

Role of microbial and chemical composition in toxicological properties of indoor and outdoor air particulate matter.

BACKGROUND: Ambient air particulate matter (PM) is increasingly considered to be a causal factor evoking severe adverse health effects. People spend the majority of their time indoors, which should be taken into account especially in future risk assessments, when the role of outdoor air particles transported into indoor air is considered. Therefore, there is an urgent need for characterization of possible sources seasonally for harmful health outcomes both indoors and outdoors. METHODS: In this study, we collected size-segregated (PM(10-2.5), PM(2.5-0.2)) particulate samples with a high volume cascade impactor (HVCI) simultaneously both indoors and outdoors of a new single family detached house at four different seasons. The chemical composition of the samples was analyzed as was the presence of microbes. Mouse macrophages were exposed to PM samples for 24 hours. Thereafter, the levels of the proinflammatory cytokines, NO-production, cytotoxicity and changes in the cell cycle were investigated. The putative sources of the most toxic groups of constituents were resolved by using the principal component analysis (PCA) and pairwise dependencies of the variables were detected with Spearman correlation. RESULTS: Source-related toxicological responses clearly varied according to season. The role of outdoor sources in indoor air quality was significant only in the warm seasons and the significance of outdoor microbes was also larger in the indoor air. During wintertime, the role of indoor sources of the particles was more significant, as was also the case for microbes. With respect to the outdoor sources, soil-derived particles during a road dust episode and local wood combustion in wintertime were the most important factors inducing toxicological responses. CONCLUSIONS: Even though there were clear seasonal differences in the abilities of indoor and outdoor air to induce inflammatory and cytotoxic responses, there were relatively small differences in the chemical composition of the particles responsible of those effects. Outdoor sources have only a limited effect on indoor air quality in a newly built house with a modern ventilation system at least in a low air pollution environment. The most important sources for adverse health related toxicological effects were related to soil-derived constituents, local combustion emissions and microbes.

Reference particles for toxicological studies of wood combustion: formation, characteristics, and toxicity compared to those of real wood combustion particulate mass.

Multiple studies show that particulate mass (PM) generated from incomplete wood combustion may induce adverse health issues in humans. Previous findings have shown that also the PM from efficient wood combustion may induce enhanced production of reactive oxygen species (ROS), inflammation, and cytotoxicity in vitro and in vivo. Underlying factors of these effects may be traced back to volatile inorganic transition metals, especially zinc, which can be enriched in the ultrafine fraction of biomass combustion particulate emission. In this study, nanoparticles composed of potassium, sulfur, and zinc, which are the major components forming inorganic fine PM, were synthesized and tested in vitro. In addition, in vitro toxicity of PM from efficient combustion of wood chips was compared with that of the synthesized particles. Cytotoxicity, cell cycle arrest, ROS generation, and tumor necrosis factor alpha release were related to zinc concentration in PM. Potassium sulfate and potassium carbonate did not induce toxic responses. In light of the provided data, it can be concluded that zinc, enriched in wood combustion emissions, caused the toxicity in all of the measured end points.

Optical and chemical characterization of aerosols emitted from coal, heavy and light fuel oil, and small-scale wood combustion.

Particle emissions affect radiative forcing in the atmosphere. Therefore, it is essential to know the physical and chemical characteristics of them. This work studied the chemical, physical, and optical characteristics of particle emissions from small-scale wood combustion, coal combustion of a heating and power plant, as well as heavy and light fuel oil combustion at a district heating station. Fine particle (PM1) emissions were the highest in wood combustion with a high fraction of absorbing material. The emissions were lowest from coal combustion mostly because of efficient cleaning techniques used at the power plant. The chemical composition of aerosols from coal and oil combustion included mostly ions and trace elements with a rather low fraction of absorbing material. The single scattering albedo and aerosol forcing efficiency showed that primary particles emitted from wood combustion and some cases of oil combustion would have a clear climate warming effect even over dark earth surfaces. Instead, coal combustion particle emissions had a cooling effect. Secondary processes in the atmosphere will further change the radiative properties of these emissions but are not considered in this study.

Acute systemic and lung inflammation in C57Bl/6J mice after intratracheal aspiration of particulate matter from small-scale biomass combustion appliances based on old and modern technologies.

Inflammation is regarded as an important mechanism behind mortality and morbidity experienced by cardiorespiratory patients exposed to urban air particulate matter (PM). Small-scale biomass combustion is an important source of particulate air pollution. In this study, we investigated association between inflammatory responses and chemical composition of PM(1) emissions from seven different small-scale wood combustion appliances representing old and modern technologies. Healthy C57Bl/6J mice were exposed by intratracheal aspiration to single dose (10 mg/kg) of particulate samples. At 4 and 18 h after the exposure, bronchoalveolar lavage fluid (BALF) as well as serum was collected for subsequent analyses of inflammatory indicators (interleukin (IL)-6, IL-1ß, IL-12, and IL-10; tumor necrosis factor-α (TNF-α); keratinocyte-derived chemoattractant (KC), and interferon-γ (IFN-γ)) in multiplexing assay. When the responses to the PM(1) samples were compared on an equal mass basis, the PM from modern technology appliances increased IL-6, KC, and IL-1ß levels significantly in BALF at 4 and 18 h after the exposure. In contrast, these responses were seen only at 4 h time point in serum. Increased cytokine concentrations correlated with metal-rich ash related compounds which were more predominant in the modern technology furnaces emissions. These particles induced both local and systemic inflammation. Instead, polycyclic hydrocarbon (PAH) rich PM(1) samples from old technology (OT) evoked only minor inflammatory responses. In conclusion, the combustion technology largely affects the toxicological and chemical characteristics of the emissions. The large mass emissions of old combustion technology should be considered, when evaluating the overall harmfulness between the appliances. However, even the small emissions from modern technologies may pose significant toxic risks.

Toxicological properties of emission particles from heavy duty engines powered by conventional and bio-based diesel fuels and compressed natural gas.

BACKGROUND: One of the major areas for increasing the use of renewable energy is in traffic fuels e.g. bio-based fuels in diesel engines especially in commuter traffic. Exhaust emissions from fossil diesel fuelled engines are known to cause adverse effects on human health, but there is very limited information available on how the new renewable fuels may change the harmfulness of the emissions, especially particles (PM). We evaluated the PM emissions from a heavy-duty EURO IV diesel engine powered by three different fuels; the toxicological properties of the emitted PM were investigated. Conventional diesel fuel (EN590) and two biodiesels were used - rapeseed methyl ester (RME, EN14214) and hydrotreated vegetable oil (HVO) either as such or as 30% blends with EN590. EN590 and 100% HVO were also operated with or without an oxidative catalyst (DOC + POC). A bus powered by compressed natural gas (CNG) was included for comparison with the liquid fuels. However, the results from CNG powered bus cannot be directly compared to the other situations in this study. RESULTS: High volume PM samples were collected on PTFE filters from a constant volume dilution tunnel. The PM mass emission with HVO was smaller and with RME larger than that with EN590, but both biofuels produced lower PAH contents in emission PM. The DOC + POC catalyst greatly reduced the PM emission and PAH content in PM with both HVO and EN590. Dose-dependent TNFα and MIP-2 responses to all PM samples were mostly at the low or moderate level after 24-hour exposure in a mouse macrophage cell line RAW 264.7. Emission PM from situations with the smallest mass emissions (HVO + cat and CNG) displayed the strongest potency in MIP-2 production. The catalyst slightly decreased the PM-induced TNFα responses and somewhat increased the MIP-2 responses with HVO fuel. Emission PM with EN590 and with 30% HVO blended in EN590 induced the strongest genotoxic responses, which were significantly greater than those with EN590 + cat or 100% HVO. The emission PM sample from the CNG bus possessed the weakest genotoxic potency but had the strongest oxidative potency of all the fuel and catalyst combinations. The use of 100% HVO fuel had slightly weaker and 100% RME somewhat stronger emission PM induced ROS production, when compared to EN590. CONCLUSIONS: The harmfulness of the exhaust emissions from vehicle engines cannot be determined merely on basis of the emitted PM mass. The study conditions and the engine type significantly affect the toxicity of the emitted particles. The selected fuels and DOC + POC catalyst affected the PM emission from the heavy EURO IV engine both qualitative and quantitative ways, which influenced their toxicological characteristics. The plain HVO fuel performed very well in emission reduction and in lowering the overall toxicity of emitted PM, but the 30% blend of HVO in EN590 was no better in this respect than the plain EN590. The HVO with a DOC + POC catalyst in the EURO IV engine, performed best with regard to changes in exhaust emissions. However some of the toxicological parameters were significantly increased even with these low emissions.

Efficiency of log wood combustion affects the toxicological and chemical properties of emission particles.

CONTEXT: Particulate matter (PM) has been identified as a major environmental pollutant causing severe health problems. Large amounts of the harmful particulate matter (PM) are emitted from residential wood combustion, but the toxicological properties of wood combustion particles are poorly known. OBJECTIVE: To investigate chemical and consequent toxicological characteristics of PM(1) emitted from different phases of batch combustion in four heating appliances. MATERIALS AND METHODS: Mouse RAW264.7 macrophages and human BEAS-2B bronchial epithelial cells were exposed for 24 h to different doses (15-300 µg/mL) of wood combustion particles. After the exposure, cytotoxicity, genotoxicity, production of the inflammatory mediators (TNF-α and MIP-2) and effects on the cell cycle were assessed. Furthermore, the detected toxicological responses were compared with the chemical composition of PM(1) samples including PAHs, metals and ions. RESULTS: All the wood combustion samples exerted high cytotoxicity, but only moderate inflammatory activity. The particles emitted from the inefficient phase of batch combustion in the sauna stove (SS) induced the most extensive cytotoxic and genotoxic responses in mammalian cells. Polycyclic aromatic hydrocarbons (PAHs) and other organic compounds in PM(1) samples might have contributed to these effects. Instead, water-soluble metals seemed to participate in the cytotoxic responses triggered by the particles from more efficient batch combustion in the masonry heaters. Overall, the toxicological responses were decreased when the combustion phase was more efficient. CONCLUSION: Efficiency of batch combustion plays a significant role in the harmfulness of PM even under incomplete wood combustion processes.

Toxicological effects of emission particles from fossil- and biodiesel-fueled diesel engine with and without DOC/POC catalytic converter.

There is increasing demand for renewable energy and the use of biodiesel in traffic is a major option when implying this increment. We investigated the toxicological activities of particulate emissions from a nonroad diesel engine, operated with conventional diesel fuel (EN590), and two biodiesels: rapeseed methyl ester (RME) and hydrotreated fresh vegetable oil (HVO). The engine was operated with all fuels either with or without catalyst (DOC/POC). The particulate matter (PM(1)) samples were collected from the dilution tunnel with a high-volume cascade impactor (HVCI). These samples were characterized for ions, elements, and polycyclic aromatic hydrocarbon (PAH) compounds. Mouse RAW264.7 macrophages were exposed to the PM samples for 24 h. Inflammatory mediators, (TNF-α and MIP-2), cytotoxicity, genotoxicity, and oxidative stress (reactive oxygen species [ROS]) were measured. All the samples displayed mostly dose-dependent toxicological activity. EN590 and HVO emission particles had larger inflammatory responses than RME-derived particles. The catalyst somewhat increased the responses per the same mass unit. There were no substantial differences in the cytotoxic responses between the fuels or catalyst use. Genotoxic responses by all the particulate samples were at same level, except weaker for the RME sample with catalyst. Unlike other samples, EN590-derived particles did not significantly increase ROS production. Catalyst increased the oxidative potential of the EN590 and HVO-derived particles, but decreased that with RME. Overall, the use of biodiesel fuels and catalyst decreased the particulate mass emissions compared with the EN590 fuel. Similar studies with different types of diesel engines are needed to assess the potential benefits from biofuel use in engines with modern technologies.

Airway exposure to silica-coated TiO2 nanoparticles induces pulmonary neutrophilia in mice.

The importance of nanotechnologies and engineered nanoparticles has grown rapidly. It is therefore crucial to acquire up-to-date knowledge of the possible harmful health effects of these materials. Since a multitude of different types of nanosized titanium dioxide (TiO(2)) particles are used in industry, we explored their inflammatory potential using mouse and cell models. BALB/c mice were exposed by inhalation for 2 h, 2 h on 4 consecutive days, or 2 h on 4 consecutive days for 4 weeks to several commercial TiO(2) nanoparticles, SiO(2) nanoparticles, and to nanosized TiO(2) generated in a gas-to-particle conversion process at 10 mg/m(3). In addition, effects of in vitro exposure of human macrophages and fibroblasts (MRC-9) to the different particles were assessed. SiO(2)-coated rutile TiO(2) nanoparticles (cnTiO(2)) was the only sample tested that elicited clear-cut pulmonary neutrophilia. Uncoated rutile and anatase as well as nanosized SiO(2) did not induce significant inflammation. Pulmonary neutrophilia was accompanied by increased expression of tumor necrosis factor-alpha (TNF-alpha) and neutrophil-attracting chemokine CXCL1 in the lung tissue. TiO(2) particles accumulated almost exclusively in the alveolar macrophages. In vitro exposure of murine and human macrophages to cnTiO(2) elicited significant induction of TNF-alpha and neutrophil-attracting chemokines. Stimulation of human fibroblasts with cnTiO(2)-activated macrophage supernatant induced high expression of neutrophil-attracting chemokines, CXCL1 and CXCL8. Interestingly, the level of lung inflammation could not be explained by the surface area of the particles, their primary or agglomerate particle size, or radical formation capacity but is rather explained by the surface coating. Our findings emphasize that it is vitally important to take into account in the risk assessment that alterations of nanoparticles, e.g., by surface coating, may drastically change their toxicological potential.