Laboratory Performance Evaluation of a Low-Cost Electrochemical Formaldehyde Sensor.

Formaldehyde is a known human carcinogen and an important indoor and outdoor air pollutant. However, current strategies for formaldehyde measurement, such as chromatographic and optical techniques, are expensive and labor intensive. Low-cost gas sensors have been emerging to provide effective measurement of air pollutants. In this study, we evaluated eight low-cost electrochemical formaldehyde sensors (SFA30, Sensirion®, Staefa, Switzerland) in the laboratory with a broadband cavity-enhanced absorption spectroscopy as the reference instrument. As a group, the sensors exhibited good linearity of response (R2 > 0.95), low limit of detection (11.3 ± 2.07 ppb), good accuracy (3.96 ± 0.33 ppb and 6.2 ± 0.3% N), acceptable repeatability (3.46% averaged coefficient of variation), reasonably fast response (131-439 s) and moderate inter-sensor variability (0.551 intraclass correlation coefficient) over the formaldehyde concentration range of 0-76 ppb. We also systematically investigated the effects of temperature and relative humidity on sensor response, and the results showed that formaldehyde concentration was the most important contributor to sensor response, followed by temperature, and relative humidity. The results suggest the feasibility of using this low-cost electrochemical sensor to measure formaldehyde concentrations at relevant concentration ranges in indoor and outdoor environments.

Aerosol Generation During Nasal Airway Instrumentation.

OBJECTIVE: Airborne aerosol transmission, an established mechanism of SARS-CoV-2 spread, has been successfully mitigated in the health care setting through the adoption of universal masking. Upper airway endoscopy, however, requires direct access to the face, thereby potentially exposing the clinic environment to infectious particles. This study quantifies aerosol production during rigid nasal endoscopy (RNE) and RNE with debridement (RNED) as compared with intubation, a posited gold standard aerosol-generating procedure. STUDY DESIGN: Prospective cross-sectional study. SETTING: Subspecialty single-center clinic and surgical study. METHOD: Three aerosol detectors (NANOSCAN-3910, OPS-3330, and APS-3321) with a particle size sensitivity of 10 to 20,000 nm were utilized to detect particulate production during the clinical care of 209 patients undergoing RNE/RNED and 25 patients undergoing intubation. RESULTS: RNE and RNED produced statistically significant particles over baseline in 29.3% and 51.0% of subjects (P = .003-.049 and .002-.047, respectively). Intubation produced statistically significant particles in 31.2% (P = .001-.015). The mean ± SD particle diameter in all tests was 69.9 ± 10.5 nm with 99.7% <300 nm. There were no statistical differences in particle production among RNE, RNED, and intubation. The presence of concomitant cough, sneeze, or prolonged speech similarly did not significantly affect particle production during any procedure. CONCLUSIONS: Instrumentation of nasal airway produces airborne aerosols to a similar degree of those seen during intubation, independent of reactive patient behaviors such as cough or sneeze. These data suggest that an improved understanding is necessary of both the definition of an aerosol-generating procedure and the functional consequences of procedural aerosol generation in clinical settings.

Comparison of biological responses between submerged, pseudo-air-liquid interface, and air-liquid interface exposure of A549 and differentiated THP-1 co-cultures to combustion-derived particles.

Air liquid interface (ALI) exposure systems are gaining interest, and studies suggest enhanced response of lung cells exposed to particles at ALI as compared to submerged exposure, although the results have been somewhat inconsistent. Previous studies have used monocultures and measured particle deposition using assumptions including consistent particle deposition, particle density, and shape. This study exposed co-cultures of A549 and differentiated THP-1 cells to flame-generated particles using three exposure methods: ALI, pseudo-ALI, and submerged. The dose at ALI was measured directly, reducing the need for assumptions about particle properties and deposition. For all exposure methods an enhanced pro-inflammatory response (TNFα) and Cytochrome P450 (CYP1A1) gene expression, compared to their corresponding negative controls, was observed. ALI exposure induced a significantly greater TNFα response compared to submerged exposure. The submerged exposures exhibited greater induction of CYP1A1 than other exposure methods, although not statistically significant. Some of the factors behind the observed difference in responses for the three exposure methods include differences in physicochemical properties of particles in suspending media, delivered dose, and potential contribution of gas-phase species to cellular response in ALI exposure. However, given the difficulty and expense of ALI exposures, submerged exposure may still provide relevant information for particulate exposures.

Effect of collection methods on combustion particle physicochemical properties and their biological response in a human macrophage-like cell line.

In vitro studies are a first step toward understanding the biological effects of combustion-derived particulate matter (cdPM). A vast majority of studies expose cells to cdPM suspensions, which requires a method to collect cdPM and suspend it in an aqueous media. The consequences of different particle collection methods on particle physiochemical properties and resulting biological responses are not fully understood. This study investigated the effect of two common approaches (collection on a filter and a cold plate) and one relatively new (direct bubbling in DI water) approach to particle collection. The three approaches yielded cdPM with differences in particle size distribution, surface area, composition, and oxidative potential. The directly bubbled sample retained the smallest sized particles and the bimodal distribution observed in the gas-phase. The bubbled sample contained ∼50% of its mass as dissolved species and lower molecular weight compounds, not found in the other two samples. These differences in the cdPM properties affected the biological responses in THP-1 cells. The bubbled sample showed greater oxidative potential and cellular reactive oxygen species. The scraped sample induced the greatest TNFα secretion. These findings have implications for in vitro studies of air pollution and for efforts to better understand the underlying mechanisms.

Effects of fuel components and combustion particle physicochemical properties on toxicological responses of lung cells.

The physicochemical properties of combustion particles that promote lung toxicity are not fully understood, hindered by the fact that combustion particles vary based on the fuel and combustion conditions. Real-world combustion-particle properties also continually change as new fuels are implemented, engines age, and engine technologies evolve. This work used laboratory-generated particles produced under controlled combustion conditions in an effort to understand the relationship between different particle properties and the activation of established toxicological outcomes in human lung cells (H441 and THP-1). Particles were generated from controlled combustion of two simple biofuel/diesel surrogates (methyl decanoate and dodecane/biofuel-blended diesel (BD), and butanol and dodecane/alcohol-blended diesel (AD)) and compared to a widely studied reference diesel (RD) particle (NIST SRM2975/RD). BD, AD, and RD particles exhibited differences in size, surface area, extractable chemical mass, and the content of individual polycyclic aromatic hydrocarbons (PAHs). Some of these differences were directly associated with different effects on biological responses. BD particles had the greatest surface area, amount of extractable material, and oxidizing potential. These particles and extracts induced cytochrome P450 1A1 and 1B1 enzyme mRNA in lung cells. AD particles and extracts had the greatest total PAH content and also caused CYP1A1 and 1B1 mRNA induction. The RD extract contained the highest relative concentration of 2-ring PAHs and stimulated the greatest level of interleukin-8 (IL-8) and tumor necrosis factor-alpha (TNFα) cytokine secretion. Finally, AD and RD were more potent activators of TRPA1 than BD, and while neither the TRPA1 antagonist HC-030031 nor the antioxidant N-acetylcysteine (NAC) affected CYP1A1 or 1B1 mRNA induction, both inhibitors reduced IL-8 secretion and mRNA induction. These results highlight that differences in fuel and combustion conditions affect the physicochemical properties of particles, and these differences, in turn, affect commonly studied biological/toxicological responses.

Characterization of exhaust particles from military vehicles fueled with diesel, gasoline, and JP-8.

Diluted exhaust from selected military aircraft ground-support equipment (AGE) was analyzed for particulate mass, elemental carbon (EC) and organic carbon (OC), SO4(2-), and size distributions. The experiments occurred at idle and load conditions and utilized a chassis dynamometer. The selected AGE vehicles operated on gasoline, diesel, and JP-8. These military vehicles exhibited concentrations, size distributions, and emission factors in the same range as those reported for nonmilitary vehicles. The diesel and JP-8 emission rates for PM ranged from 0.092 to 1.1 g/kg fuel. The EC contributed less and the OC contributed more to the particulate mass than reported in recent studies of vehicle emissions. Overall, the particle size distribution varied significantly with engine condition, with the number of accumulation mode particles and the count median diameter (CMD) increasing as engine load increased. The SO4(2-) analyses showed that the distribution of SO4(2-) mass mirrored the distribution of particle mass.