Corrosion behavior of Ti-Pt-coated stainless steel for bipolar plates in polymer electrolyte membranes under water electrolysis conditions.

In this study, the corrosion behavior and degradation mechanism of Ti-Pt-coated stainless steel bipolar plates were investigated through electrochemical tests and surface analysis in a polymer electrolyte membrane water electrolysis (PEMWE) operating environment. The coated bipolar plate has a corrosion current density of only 1.68 × 10-8 A/cm2, which is an order of magnitude lower than that of the bare SS316L substrate (1.94 × 10-7 A/cm2), indicating that its corrosion resistance is superior to that of bare SS316L substrate. However, in the PEMWE operating environment, the protection efficiency of the coating and the corrosion resistance of the coated bipolar plate decreased. The degradation of the coated bipolar plate can be attributed to electrolyte penetration into the blistering areas of the coating layer with micro voids. Defects in the coating layer occur because of the pressure of oxygen gas generated within the coating layer under high-potential conditions, thereby exposing the substrate to the electrolyte and corrosion.

Effect of Frequency and Ratio of Wet/Dry Stages in Cyclic Corrosion Tests on Localized Corrosion of Complex-Phase High-Strength Steel.

This study delves into the atmospheric corrosion behavior of chromium-free complex-phase (CP) steel, specifically investigating the influence of wet/dry frequency and ratio in cyclic corrosion tests (CCT). The study employs a modified ISO 14993 standard CCT method, which involves salt spray, dry, and wet stages. After 15 and 30 CCT cycles, mass loss, maximum corrosion depth, and corrosion products were analyzed to gain insights into corrosion mechanisms. In general, increasing the frequency and wet/dry stage ratio in CCT extends the time for autocatalytic reactions to occur, leading to accelerated localized CP steel corrosion and increased pitting factors. However, as the rust layer thickens, uniform corrosion may also intensify, so careful considerations are necessary. This study underscores the importance of controlling the frequency and ratio of wet/dry stages in CCT for effectively analyzing localized corrosion behavior in specimens.

New Accelerated Corrosion Test Method Simulating Atmospheric Corrosion of Complex Phase Steel Combining Cyclic Corrosion Test and Electrochemically Accelerated Corrosion Test.

The automobile industry commonly uses cyclic corrosion tests (CCTs) to evaluate the durability of materials. However, the extended evaluation period required by CCTs can pose challenges in this fast-paced industry. To address this issue, a new approach that combines a CCT with an electrochemically accelerated corrosion test has been explored, to shorten the evaluation period. This method involves the formation of a corrosion product layer through a CCT, which leads to localized corrosion, followed by applying an electrochemically accelerated corrosion test using an agar gel electrolyte to preserve the corrosion product layer as much as possible. The results indicate that this approach can achieve comparable localized corrosion resistance, with similar localized corrosion area ratios and maximum localized corrosion depths to those obtained through a conventional CCT in half the time.

Effect of Sulfide and Chloride Ions on Pitting Corrosion of Type 316 Austenitic Stainless Steel in Groundwater Conditions Using Response Surface Methodology.

This study investigates the corrosion resistance of Type 316 stainless steel as a candidate material for radioactive waste disposal canisters. The viability of stainless steel is examined under groundwater conditions with variations in pH, bisulfide ions (HS-), and chloride ions (Cl-) concentrations. Utilizing response surface methodology, correlations between corrosion factors and two crucial response variables, passive film breakdown potential and protection potential, are established. Cyclic potentiodynamic polarization tests and advanced analytical techniques provide detailed insights into the material's behavior. This research goes beyond, deriving an equation through response surface methodology that elucidates the relationship between the factors and breakdown potential. HS- weakens the passive film and reduces the pitting corrosion resistance of the stainless steel. However, this study highlights the inhibitory effect of HS- on pitting corrosion when Cl- concentrations are below 0.001 M and at equivalent concentrations of HS-. Under these conditions, immediate re-passivation occurs from the destroyed passive film to metal sulfides such as FeS2, MoS2, and MoS3. As a result, no hysteresis loop occurs in the cyclic polarization curve in these conditions. This research contributes to the understanding of Type 316 stainless-steel corrosion behavior, offering implications for the disposal of radioactive waste in geological repositories.

Machine learning modeling of predictive external corrosion rates of spent nuclear fuel carbon steel canister in soil.

Soil corrosion is always a critical concern to corrosion engineering because of the economic influence of soil infrastructures as has been and has recently been the focus of spent nuclear fuel canisters. Besides corrosion protection, the corrosion prediction of the canister is also important. Advanced knowledge of the corrosion rate of spent nuclear fuel canister material in a particular environment can be extremely helpful in choosing the best protection method. Applying machine learning (ML) to corrosion rate prediction solves all the challenges because of the number of variables affecting soil corrosion. In this study, several algorithms of ML, including series individual, boosting, bagging artificial neural network (ANN), series individual, boosting, bagging Chi-squared automatic interaction detection (CHAID) tree decision, linear regression (LR) and an ensemble learning (EL) merge the best option that collects from 3 algorithm methods above. From the performance of each model to find the model with the highest accuracy is the ensemble stacking method. Mean absolute error performance matrices are shown in Fig. 15. Besides applying ML, the significance of the input variables was also determined through sensitivity analysis using the feature importance criterion, and the carbon steel corrosion rate is the most sensitive to temperature and chloride.

Localized Corrosion Occurrence in Low-Carbon Steel Pipe Caused by Microstructural Inhomogeneity.

In this study, the cause of failure of a low-carbon steel pipe meeting standard KS D 3562 (ASTM A135), in a district heating system was investigated. After 6 years of operation, the pipe failed prematurely due to pitting corrosion, which occurred both inside and outside of the pipe. Pitting corrosion occurred more prominently outside the pipe than inside, where water quality is controlled. The analysis indicated that the pipe failure occurred due to aluminum inclusions and the presence of a pearlite inhomogeneous phase fraction. Crevice corrosion occurred in the vicinity around the aluminum inclusions, causing localized corrosion. In the large pearlite fraction region, cementite in the pearlite acted as a cathode to promote dissolution of surrounding ferrite. Therefore, in the groundwater environment outside of the pipe, localized corrosion occurred due to crevice corrosion by aluminum inclusions, and localized corrosion was accelerated by the large fraction of pearlite around the aluminum inclusions, leading to pipe failure.

Evaluation of the Influence of the Combination of pH, Chloride, and Sulfate on the Corrosion Behavior of Pipeline Steel in Soil Using Response Surface Methodology.

External damage to buried pipelines is mainly caused by corrosive components in soil solution. The reality that numerous agents are present in the corrosive environment simultaneously makes it troublesome to study. To solve that issue, this study aims to determine the influence of the combination of pH, chloride, and sulfate by using a statistical method according to the design of experiment (DOE). Response surface methodology (RSM) using the Box-Behnken design (BBD) was selected and applied to the design matrix for those three factors. The input corrosion current density was evaluated by electrochemical tests under variable conditions given in the design matrix. The output of this method is an equation that calculates the corrosion current density as a function of pH, chloride, and sulfate concentration. The level of influence of each factor on the corrosion current density was investigated and response surface plots, contour plots of each factor were created in this study.

Spent Coffee Grounds as Eco-Friendly Additives for Aluminum-Air Batteries.

A new approach to the recycling of spent coffee grounds is described in which lignin, a chemical component of spent coffee, is used as an electrolyte additive in aluminum-air batteries. The effect of lignin on the performance of aluminum-air batteries has been investigated by weight loss measurement, galvanostatic discharge test, and electrochemical impedance spectroscopy (EIS). The corrosion inhibition efficiency is improved up to 37.3% and fuel efficiency up to 21.7% at 500 ppm of lignin molecules. The chemisorption of lignin molecules on the aluminum surface improves battery performance. Adsorption of lignin molecules onto the aluminum surface is driven by the electrostatic interaction between the lignin's hydroxyl group and the aluminum surface. The mechanism for the performance improvement is explained by the chemisorption behavior of lignin molecules. The adsorption behavior has been investigated by scanning electronic microscopy with energy-dispersive spectroscopy (SEM-EDS), laser scanning microscopy (LSM), atomic force microscopy (AFM), Freundlich adsorption isotherm, Fourier-transform infrared (FT-IR) spectroscopy, and the computational calculation of adsorption energies based on the density functional theory (DFT).

Effect of Imidazole as Corrosion Inhibitor on Carbon Steel Weldment in District Heating Water.

Many research studies have been conducted on the corrosion inhibition performance of imidazole in acidic environments such as in the piping of a petrochemical plant. However, there has been no study on the effect of imidazole in alkaline conditions such as a local district water heating environment. Therefore, in this study, the effect of imidazole as a corrosion inhibitor on carbon steel weldment was investigated in alkaline district heating water. Inhibition efficiency and electrochemical properties were investigated by potentiodynamic polarization test and electrochemical impedance spectroscopy. As the concentration of imidazole increased up to 500 ppm, inhibition efficiency increased up to 91.7%. At 1000 ppm, inhibition efficiency decreased. Atomic force microscopy showed that surface coverage of imidazole at 1000 ppm is lower than that of imidazole at 500 ppm. X-ray photoelectron spectroscopy showed that with 500 ppm of imidazole, the amount of pyrrole type interaction is 4.8 times larger than pyridine type interaction. At 1000 ppm of imidazole, the amount of pyridine type interaction is 3.49 times larger than pyrrole type interaction. Depending on the concentration of imidazole, the ratio of interaction between carbon steel and imidazole affected inhibition efficiency.

Effect of Cr on Aqueous and Atmospheric Corrosion of Automotive Carbon Steel.

This study investigated the effect of Cr alloying element on the corrosion properties of automotive carbon steel (0.1C, 0.5Si, 2.5Mn, Fe Bal., composition given in wt.%) in aqueous and atmospheric conditions using electrochemical measurement and cyclic corrosion tests. Three steels with 0, 0.3, and 0.5 wt.% Cr were studied by electrochemical impedance spectroscopy. Polarization resistance (Rp) of 0.3 Cr and 0.5 Cr steels was higher than that of 0 Cr steel, and the Rp also increased as the Cr content increased. Therefore, Cr increases the corrosion resistance of automotive carbon steel immersed in a chloride ion (Cl-)-containing aqueous solution. In the cyclic corrosion test results, Cl- was concentrated at the metal/rust interface in all of the steels regardless of Cr content. The Cl- was uniformly concentrated and distributed on the 0 Cr steel, but locally and non-uniformly concentrated on the Cr-added steels. The inner rust layer consisted of ß-FeOOH containing Cl- and Cr-goethite, while the outer rust layer was composed of amorphous iron oxyhydroxide mixed with various types of rust. FeCl2 and CrCl3 are formed from the Cl- nest developed in the early stage, and the pitting at CrCl3-formed regions are locally accelerated because Cr is strongly hydrolyzed to a very low pH.

Highly Sensitive Electrochemical Aptasensor for Detecting the VEGF165 Tumor Marker with PANI/CNT Nanocomposites.

Sensing targeted tumor markers with high sensitivity provides vital information for the fast diagnosis and treatment of cancer patients. A vascular endothelial growth factor (VEGF165) have recently emerged as a promising biomarker of tumor cells. The electrochemical aptasensor is a promising tool for detecting VEGF165 because of its advantages such as a low cost and quantitative analysis. To produce a sensitive and stable sensor electrode, nanocomposites based on polyaniline (PANI) and carbon nanotube (CNT) have potential, as they provide for easy fabrication, simple synthesis, have a large surface area, and are suitable in biological environments. Here, a label-free electrochemical aptasensor based on nanocomposites of CNT and PANI was prepared for detecting VEGF165 as a tumor marker. The nanocomposite was assembled with immobilized VEGF165 aptamer as a highly sensitive VEGF165 sensor. It exhibited stable and wide linear detection ranges from 0.5 pg/mL to 1 µg/mL, with a limit of detection of 0.4 pg/mL because of the complementary effect of PANI/CNT. The fabricated aptasensor also exhibited good stability in biological conditions, selectivity, and reproducibility after several measurement times after the dissociation process. Thus, it could be applied for the non-invasive determination of VEGF, in biological fluid diagnosis kits, or in an aptamer-based biosensor platform in the near future.

Electroplated Silver-Nickel Core-Shell Nanowire Network Electrodes for Highly Efficient Perovskite Nanoparticle Light-Emitting Diodes.

The low sheet resistance and high optical transparency of silver nanowires (AgNWs) make them a promising candidate for use as the flexible transparent electrode of light-emitting diodes (LEDs). In a perovskite LED (PeLED), however, the AgNW electrode can react with the overlying perovskite material by redox reactions, which limit the electroluminescence efficiency of the PeLED by causing the degradation of and generating defect states in the perovskite material. In this study, we prepared Ag-Ni core-shell NW electrodes using the solution-electroplating technique to realize highly efficient PeLEDs based on colloidal formamidinium lead bromide (FAPbBr3) nanoparticles (NPs). Solvated Ni ions from the NiSO4 source were deposited onto the surface of AgNW networks in three steps: (i) cathodic cleaning, (ii) adsorption of the Ni-ion complex onto the AgNW surface, and (iii) uniform electrodeposition of Ni. An ultrathin (∼3.5 nm) Ni layer was uniformly deposited onto the AgNW surface, which exhibited a sheet resistance of 16.7 Ω/sq and an optical transmittance of 90.2%. The Ag-Ni core-shell NWs not only increased the work function of the AgNW electrode, which facilitated hole injection into the emitting layer, but also suppressed the redox reaction between Ag and FAPbBr3 NPs, which prevented the degradation of the emitting layer and the generation of defect states in it. The resulting PeLEDs based on FAPbBr3 NPs with the Ag-Ni core-shell NWs showed high current efficiency of 44.01 cd/A, power efficiency of 35.45 lm/W, and external quantum efficiency of 9.67%.

Effects of Corrosion on Mechanical Properties of Welded Carbon Steel Pipe in District Heating Water.

This study examined the effect of corrosion on mechanical properties of welded carbon steel pipe in district heating water. To evaluate the corrosion properties, potentiodynamic tests were conducted and a galvanostatic test was used to accelerate corrosion. Tensile tests and microstructure observations were performed to figure out the degradation of the corroded region, and stress intensity factors were calculated. As a result of the potentiodynamic tests, welded carbon steel pipe showed uniform corrosion and the total charge was calculated. Using the galvanostatic test, the current density at the equivalent aging time was applied to the specimens. The tensile tests showed that according to corrosion damages, mechanical properties were degraded due to corrosion. Through the microstructure observations and calculations of stress intensity factors, the corrosion of the welded carbon steel pipe induced the degradation of mechanical properties. The mode of fracture was changed from ductile to brittle fracture with increasing aging time.

Investigation of Zirconium Effect on the Corrosion Resistance of Aluminum Alloy Using Electrochemical Methods and Numerical Simulation in an Acidified Synthetic Sea Salt Solution.

Corrosion resistance of Zr that has been added to an Al alloy (U1070) is higher than that of a commercial Al alloy (A1070). A decreasing number and size of Al3Fe intermetallic particles (IMPs) were observed by electron microprobe analysis and transmission electron microscopy. Based on the numerical corrosion simulation, it was confirmed that decreasing the number and size of IMPs was favorable for improving the corrosion resistance of the Al alloy due to the reduction of the galvanic effect. In addition, Al3Zr was found to be insignificant in promoting galvanic corrosion within the Al matrix. Thus, Zr is an advantageous alloying element for improving the corrosion resistance of the Al alloy.

Influence of Magnesium Ions in the Seawater Environment on the Improvement of the Corrosion Resistance of Low-Chromium-Alloy Steel.

This study examined the synergic effect of alloying the element Cr and the environmental element Mg2+ ions on the corrosion property of a low-alloy steel in seawater at 60 °C, by means of electrochemical impedance spectroscopy (EIS), linear polarization resistance (LPR) tests and weight-loss tests. The Mg2+ ions in seawater played an important role in lowering the electron transfer of the rust layer in the Cr-containing steel. The corrosion resistance of the Cr-containing steel is superior to that of blank steel in Mg2+ ions containing seawater. XPS and XRD results indicated that the formation of MgFe2O4 and a mixed layer (Cr oxide + FeCr2O4 + MgCr2O4) improved the corrosion resistance of the low-alloy steel in the seawater.

Cannabinoid receptor gene polymorphisms and bone mineral density in Korean postmenopausal women.

OBJECTIVE: We investigated the association between single nucleotide polymorphisms in cannabinoid receptor (CNR) genes and bone mineral density (BMD) in Korean postmenopausal women. METHODS: Seven polymorphisms (rs2023239, rs806379, rs12720071, rs1049353, rs806368, rs2180619, and rs7766029) in the cannabinoid receptor type 1 (CNR1) gene and 16 polymorphisms (rs2501432, rs2502992, rs2501431, rs3003336, rs4649124, rs2502993, rs2229579, rs2229580, rs2229581, rs2229583, rs2229584, rs2229585, rs2229586, rs4237, rs7530595, and rs16828926) in the cannabinoid receptor type 2 (CNR2) gene were analyzed in 405 Korean postmenopausal women. Serum levels of bone turnover markers, osteoprotegerin (OPG), and soluble receptor activator of nuclear factor-κB ligand (sRANKL) were measured, and BMD at the lumbar spine and femoral neck was examined. RESULTS: The CNR2 rs2501431, rs3003336, rs2229579, and rs4237 polymorphisms in CNR genes were associated with lumbar spine BMD. Women with the AA genotype of rs3003336 and rs4237 polymorphisms had significantly lower lumbar spine BMD compared with women with the non-AA genotype. Lumbar spine BMD in women with the TT genotype of CNR2 rs2501431 and rs2229579 polymorphisms was significantly lower than that in women with the non-TT genotype. Significantly higher odds for osteoporosis of the lumbar spine and/or femoral neck were observed in women with the TT genotype of rs2229579 polymorphisms (odds ratio, 3.43; 95% CI, 1.28-9.19) and with the AA genotype of rs4237 polymorphisms (odds ratio, 1.74; 95% CI, 1.03-2.95) compared with those not carrying the genotypes. The adjusted serum levels of bone turnover markers, OPG, sRANKL, or sRANKL × 1,000-to-OPG ratios were not associated with CNR gene polymorphisms. CONCLUSIONS: Our results suggest that rs2501431, rs3003336, rs2229579, and rs4237 polymorphisms in CNR genes may be genetic factors affecting BMD in Korean postmenopausal women.

Association between polymorphisms in sclerostin, dickkopfs and secreted frizzled-related protein genes and bone mineral density in postmenopausal Korean women.

BACKGROUND/AIMS: The purpose of this study was to investigate the association between single nucleotide polymorphisms (SNPs) in sclerostin (SOST), dickkopf (DKK), secreted frizzled-related protein (sFRP) genes and bone mineral density (BMD) in postmenopausal Korean women. METHODS: The SOST, Wnt inhibitory factor 1 (WIF1), sFRP1,sFRP2,sFRP3, sFRP4, sFRP5, DKK1, DKK2 and DKK3 polymorphisms were analyzed in 399 postmenopausal Korean women. Serum levels of bone turnover markers were measured, and BMDs at the lumbar spine and femoral neck were also examined. RESULTS: No significant differences in adjusted BMD at the lumbar spine and femoral neck were noted according to any single and combined polymorphisms measured in SOST, DKKs and sFRPs. However, osteoporosis at the femoral neck was 2.35 times more frequently observed in the AA genotype of the sFRP4 c.958C>A polymorphism compared to the non-AA genotype (95% CI 1.09-5.08, p = 0.03). Also, the CC genotype of the sFRP3 c.970C>G polymorphism had a higher rate of osteoporosis at the femoral neck compared to the GC genotype (OR 8.47, 95% CI 1.37-52.63, p = 0.049). CONCLUSIONS: Our results suggest that the sFRP3 c.970C>G and sFRP4 c.958C>A polymorphisms may be genetic factors associated with the prevalence of osteoporosis at the femoral neck in postmenopausal Korean women.

Shared decision-making on the use of hormone therapy: a nationwide survey in the Republic of Korea.

OBJECTIVE: This study aims to assess the current status of shared decision-making on instituting postmenopausal hormone therapy (HT). METHODS: Two cross-sectional nationwide surveys of postmenopausal women and primary care physicians in the Republic of Korea were conducted in 2012 via face-to-face interviews. A total of 685 women (aged 50-69 y) who with natural menopause and 250 primary care physicians were included. RESULTS: Only 56.8% of primary care physicians reported that they explain the benefits and risks of HT and leave the decision to postmenopausal women. The others usually recommended using or not using HT. Of those postmenopausal women who had discussed such therapy with physicians (147 of 685; 21.5%), not all were aware of breast cancer or cardiovascular risks (only 65.3% and 38.8% were informed, respectively). Although most physicians perceived HT as beneficial for menopausal symptom control (99.6%) and acknowledged the related risk of breast cancer (84.8%), nearly half had the impression that HT was preventive of cardiovascular diseases. The interviewed women were less informed of the benefits and risks of HT than were the physician respondents. The awareness levels of the treated and untreated women did not differ. CONCLUSIONS: Participation of postmenopausal women in deciding whether to use HT is not prevalent. Physician-woman information transfer is suboptimal, and treatment decisions often are not based on the best available evidence. The current status of shared decision-making in this setting is clearly in need of improvement.

Association between polymorphisms in leptin, leptin receptor, and ß-adrenergic receptor genes and bone mineral density in postmenopausal Korean women.

OBJECTIVE: The purpose of this study was to investigate the association between single nucleotide polymorphisms in leptin (LEP), leptin receptor (LEPR), and ß-adrenergic receptor (ADRB) genes and bone mineral density (BMD) in postmenopausal Korean women. METHODS: LEP c.280G>A, LEPR c.326A>G, LEPR c.668A>G, LEPR c.1968G>C, LEPR c.2096C>T, ADRB2 c.46A>G, ADRB2 c.79C>G, ADRB2 c.718T>C, ADRB2 c.741G>T, ADRB2 c.769G>A, and ADRB3 c.190T>C polymorphisms were analyzed in 592 postmenopausal Korean women. Serum levels of leptin, soluble leptin receptor, osteoprotegerin, soluble receptor activator of the nuclear factor-κB ligand, bone alkaline phosphatase, and carboxy-terminal telopeptide of type I collagen were measured, and BMDs at the lumbar spine and femoral neck were also examined. RESULTS: Among the polymorphisms measured, only the LEPR c.1968G>C polymorphism was found to be associated with BMD at the femoral neck, and higher BMD was observed with increasing number of G alleles (P = 0.04). Osteoporosis at the femoral neck was 3.27 and 3.89 times more frequently observed in the AG and GG genotypes than in the AA genotype in the ADRB2 c.46A>G polymorphism (P = 0.024 and P = 0.015, respectively). However, no significant differences in serum levels of leptin, soluble leptin receptor, free leptin index, osteoprotegerin, soluble receptor activator of the nuclear factor-κB ligand, and bone turnover markers were detected among single and haplotype genotypes. CONCLUSIONS: These results suggest that the LEPR c.1968G>C polymorphism may be one of the genetic factors affecting femoral neck BMD in postmenopausal Korean women and that an analysis of the ADRB2 c.46A>G polymorphism may be useful in identifying women at risk for osteoporosis at the femoral neck.

Natural conception rate following laparoscopic surgery in infertile women with endometriosis.

OBJECTIVE: To investigate the influence of laparoscopic surgery on the natural conception rate in infertile women with endometriosis during the first year after the operation. METHODS: We retrospectively studied 43 infertile women with surgically proven endometriosis. The natural conception rate was investigated for the 12 months after the laparoscopy. RESULTS: The overall pregnancy rate was 41.9% (18/43). 66.7% (12/18) and 94.4% (17/18) of the patients conceived within postoperative 3 months and 6 months, respectively. The spontaneous pregnancy rate was not associated with the severity of endometriosis or laparoscopic findings or the type of surgery. The pregnancy rate for stage IV was relatively low (20.0%) compared to stage I, II, and III (35.7%, 44.4%, and 53.3%, respectively), although it did not reach statistical significance. CONCLUSION: Conservative surgical treatment with laparoscopy and a prompt attempt at natural conception may be effective for infertile patients with endometriosis.