Safety assessment of the process Loop Polymers, used to recycle polyethylene and polypropylene printed offcuts and scrap for use as food contact materials.

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Loop Polymers (EU register number RECYC252). The input consists of polyethylene (PE) and polypropylene (PP) offcuts and scrap from the production of food contact packaging that has not been in contact with food, but carry coatings, ink systems and adhesives. Decontaminated material is intended to be used to produce new articles for their original application. The Panel considered critical the management system put in place to provide full traceability from input to the final product, the material review before processing, as well as the removal of coatings, ink systems and adhesives during recycling. The CEP Panel considered that the applicant did not demonstrate that coatings, ink systems and adhesives were adequately removed during the process. Consequently, it concluded that the applicant has not demonstrated that the recycling process is able to reduce the contamination of the PE or PP recyclate to a concentration that does not pose a risk to human health.

Safety assessment of the process LOGIFRUIT, used to recycle high-density polyethylene and polypropylene crates for use as food contact materials.

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process LOGIFRUIT (EU register number RECYC260). The input consists of pre-washed high-density polyethylene (HDPE) or polypropylene (PP) crates from closed and controlled food distribution loops. The process separates crates by material type. Crates are ground to flakes, possibly extruded to pellets and used by companies approved to be in the loop to manufacture new crates. The Panel considered that the quality management system (QAS) put in place to ensure compliance of the origin of the input with Commission Regulation (EC) No 282/2008 and to provide full traceability is critical. The Panel concluded that, when run under the conditions described, the input of the process LOGIFRUIT exclusively originates from product loops which are in closed and controlled chains. The process is designed to ensure that only crates intended for food contact are used and that contamination other than by food can be ruled out. Therefore, the recycling process LOGIFRUIT to produce HDPE and PP crates to be used in contact with fruits and vegetables, and packed meat and fish, dairy, bakery and pastry products is not of safety concern.

Safety assessment of the process Cajas y Palets en una Economia Circular (CAPEC), used to recycle high-density polyethylene and polypropylene crates for use as food contact materials.

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Cajas y Palets en una Economia Circular (CAPEC) (EU register number RECYC242). The input consists of crates made of high-density polyethylene (HDPE) or polypropylene (PP) originating from closed and controlled product loops for the packaging of whole fruits and vegetables. Flakes or pellets are produced that will be used by manufacturers of new crates for food contact. The Panel considered that the management system put in place to ensure compliance of the origin of the input with Commission Regulation (EC) No 282/2008 and to provide full traceability from input to final product is the critical process step. It concluded that the input of the process CAPEC originates from product loops which are in closed and controlled chains designed to ensure that only materials and articles that have been intended for food contact are used and that contamination can be ruled out when run under the conditions described by the applicant. The recycling process CAPEC is therefore suitable to produce recycled HDPE and PP crates intended to be used in contact with fruits and vegetables.

Safety assessment of the process Srichakra Polyplast, based on the Starlinger iV+ technology, used to recycle post-consumer PET into food contact materials.

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process Srichakra Polyplast (EU register number RECYC229), which uses the Starlinger iV+ technology. The input is hot caustic washed and dried poly(ethylene terephthalate) (PET) flakes mainly originating from collected post-consumer PET containers, with no more than 5% PET from non-food consumer applications. The flakes are dried and crystallised in a first reactor, then extruded into pellets. These pellets are crystallised, preheated and treated in a solid-state polycondensation (SSP) reactor. Having examined the challenge test provided, the Panel concluded that the drying and crystallisation (step 2), extrusion and crystallisation (step 3) and SSP (step 4) are critical in determining the decontamination efficiency of the process. The operating parameters to control the performance of these critical steps are temperature, air flow and residence time for the drying and crystallisation step, and temperature, pressure and residence time for the extrusion and crystallisation step as well as the SSP step. It was demonstrated that this recycling process is able to ensure that the level of migration of potential unknown contaminants into food is below the conservatively modelled migration of 0.1 µg/kg food. Therefore, the Panel concluded that the recycled PET obtained from this process is not of safety concern when used at up to 100% for the manufacture of materials and articles for contact with all types of foodstuffs for long-term storage at room temperature, with or without hotfill. The final articles made of this recycled PET are not intended to be used in microwave and conventional ovens and such uses are not covered by this evaluation.

Safety assessment of the process deSter, used to recycle plastic catering tableware for use as food contact materials.

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) assessed the safety of the recycling process deSter (EU register number RECYC196). The input consists of catering tableware food contact articles from airline on-board services, made of polypropylene (PP), polyethylene terephthalate (PET), styrene acrylonitrile resin (SAN) or acrylonitrile butadiene styrene (ABS). The recyclate produced by deSter will be used to manufacture articles for the same on-board services. The Panel considered that the management system put in place to ensure compliance of the origin of the input with Commission Regulation (EC) No 282/2008 and to provide full traceability from input to final product is the critical process step. The process deSter uses only materials and articles intended for food contact and ensures that any contamination can be ruled out, since the input originates from this product loop managed in a closed and controlled chain. Therefore, the Panel concluded that the recycled materials obtained from this process and used within this loop are not of safety concern, when used at up to 100% for the manufacture of plastic tableware for contact with all types of foodstuffs under the conditions of use of the articles before recycling.

Review and priority setting for substances that are listed without a specific migration limit in Table 1 of Annex 1 of Regulation 10/2011 on plastic materials and articles intended to come into contact with food.

The EFSA Panel on Food Contact Materials, Enzymes and Processing Aids (CEP) was requested by the European Commission to review the substances for which a Specific Migration Limit (SML) is not assigned in Regulation (EU) No 10/2011. These substances had been covered by the Generic SML of 60 mg/kg food, but with Regulation (EU) 2016/1416 it was removed, necessitating their re-examination. EFSA was requested to identify those substances requiring an SML to ensure the authorisation is sufficiently protective to health, grouping them in high, medium and low priority to serve as the basis for future re-evaluations of individual substances. The CEP Panel established a stepwise procedure. This took into account existing hazard assessments for each substance on carcinogenicity/mutagenicity/reprotoxicity (CMR), bioaccumulation and endocrine disruptor (ED) properties along with the use of in silico generated predictions on genotoxicity. Molecular weights and boiling points were considered with regard to their effect on potential consumer exposure. This prioritisation procedure was applied to a total of 451 substances, from which 78 substances were eliminated at the outset, as they had previously been evaluated by EFSA as food contact substances. For 89 substances, the Panel concluded that a migration limit should not be needed. These are in the lists 0 and 1 of the Scientific Committee for Food (SCF), defined as substances for which an Acceptable Daily Intake (ADI) does not need to be established, along with substances that are controlled by existing restrictions and/or generic limits. Of the remaining 284 substances, 179 were placed into the low priority group, 102 were placed into the medium priority group and 3 were placed into the high priority group, i.e. salicylic acid (FCM No 121), styrene (FCM No 193) and lauric acid, vinyl ester (FCM No 436).

Safety assessment of the process 'Morssinkhof Plastics', used to recycle high-density polyethylene and polypropylene crates for use as food contact materials.

This scientific opinion of the EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids (CEF Panel) deals with the safety evaluation of the recycling process 'Morssinkhof Plastics', EU register No RECYC0142. The input consists of crates, boxes, trays, pallets and containers, hereafter termed 'crates', used in food contact, made of high-density polyethylene (HDPE) or polypropylene (PP). It comprises unused damaged crates, prewashed used crates and parts of crates originating from closed and controlled product loops. The process separates crates by material type and food type (fruit, vegetables and prepacked meat vs unpacked meat). Flakes from recycled HDPE or PP are produced that will be used by customers to manufacture new crates for food contact. The Panel considered that the management system put in place to ensure compliance of the origin of the input with Commission Regulation (EC) No 282/2008 and to provide full traceability from input to final product is the critical process step. It concluded that the input of the process 'Morssinkhof Plastics' originates from product loops which are in closed and controlled chains designed to ensure that only materials and articles which have been intended for food contact are used and that any contamination can be ruled out when run under the conditions described by the applicant. The recycling process 'Morssinkhof Plastics' is, therefore, able to produce recycled HDPE and PP suitable for manufacturing HDPE and PP crates intended to be used in contact with dry food, fruits and vegetables, prepacked and unpacked meat. The use of regrind from 'external' recyclers only based on private agreements, does not give reassurance to fall under the scope of Art. 4 c (i) of Commission Regulation (EC) No 282/2008 and is excluded from the present evaluation.