Health risk assessment of trace elements of ambient PM2.5 under monsoon patterns.

In order to identify the contribution to health risk derived from various emission sources, this study investigated monsoon variations in PM2.5 mass and concentrations of the associated trace elements in a region with complex pollution sources in central Taiwan. This study applied the Chemical Mass Balance model to analyze the source contribution of PM2.5. The source apportionment to obtain the risk contribution of different sources were conducted for different monsoon periods according to the monsoon patterns. In this way, the contributions of individual sources and chemicals to health risk under different monsoon types can be understood to support development of effective control strategies. Among the top contributors of PM2.5 during the north-east monsoon were Secondary Aerosol 28.93% >Coal Boiler 19.82% >Crustal Dust 15.99%; in south-west monsoon were Coal Boiler 37.29% >Traffic Emission 21.19% >Secondary Aerosol 17.84%. The total risk of cancer was above the acceptable risk (3.07 × 10-6), while the non-carcinogenic risk was within the acceptable range (0.262). The variation in the concentration and composition of PM2.5 was related to the change of monsoon type. During the north-east monsoon, the air mass had a long transmission distance and the PM2.5 concentration was relatively high. During the south-west monsoon, the air mass had a short transmission distance and the composition was mainly influenced by nearby emission sources, which resulted in higher risk due to chemical characteristics. To provide sound air quality management, attention should be paid to the composition of PM2.5 in addition to its concentration.

Assessing the transfer of risk due to transportation of agricultural products.

Health risk assessment (HRA) is the process used to estimate adverse health effects on humans. The importance and sensitivity of food chains to HRA have been observed, but the impact of the transportation of food has generally been ignored. This study developed an exposure assessment to demonstrate the significance of the transportation of agricultural products in HRA. The associated case study estimated the health risks derived from various sources of arsenic emissions in Taiwan. Two assessment scenarios, self-sufficiency and transportation of agricultural products, were compared to calculate risk transfer ratios that show the impact of agriculture transportation. The risk transfer ratios found by the study range from 0.22 to 42.10, indicating that the quantity of transportation of agricultural products is the critical factor. High air deposition and high agricultural production are the two main contributors to the effect of the transportation of agricultural products on HRA. Risk reduction measures could be applied to high-pollution areas as well as to areas with high agricultural productivity to reduce ingestion risks to residents. Certain areas that are sensitive to the transportation of agricultural products may incur more risks if emissions increase in agriculturally productive counties.

Integrating input output analysis with risk assessment to evaluate the population risk of arsenic.

Multimedia and site-specific risk assessments (RA) of major sources releasing arsenic (As) were converted into sector-based risk coefficients, which were integrated with the Input Output Table (IO) to analyze the association between sector activities and health risks. The developed IO-RA framework is a valuable tool for unfolding the risk chain linking the receptors, exposure pathways, emission sources, and production and consumption activities associated with various industrial sectors. The enlarged decision space along the chain can then be considered in planning risk management strategies. This case study estimates that air emissions of As result in 1.54 carcinogenic cases. Export is the primary driving force and accounts for approximately 48% of the final demand that leads to population risks of As. The ranking of the contribution of the five sectors in terms of total population risks is as follows: electricity supply (1.06E+00), steelmaking (2.2 × 10(-1)), cement kilns (1.50 × 10(-1)), semiconductor manufacturing (6.34 × 10(-2)) and incinerators (4.31 × 10(-2)). The electricity supply, steelmaking industry, and cement kilns are the major sectors, not only because their emissions directly cause risk but also because they have a stronger influence on the risk generated by other sectors.

Comparative study of multimedia models applied to the risk assessment of soil and groundwater contamination sites in Taiwan.

The purpose of this study was to explore the applicability of two popular multimedia risk assessment models to three different soil and groundwater contamination sites in Taiwan. The Multimedia Environmental Pollutant Assessment System (MEPAS) and the Multimedia Contaminant Fate, Transport, and Exposure Model (MMSOILS) were selected because of their wide application and use. Three soil and groundwater contamination sites in Taiwan were employed as illustrative examples in the comparison of these two risk assessment models. Three exposure pathways were investigated, categorized as oral ingestion, dermal absorption, and inhalation. The results show that MEPAS and MMSOILS calculated similar cancer risks and hazard quotients in general, but were different by two orders of magnitude in cancer risk estimates for sites contaminated by volatile organic compounds (VOC). Using MMSOILS may not be appropriate for risk assessment of such sites, as it does not account for indoor inhalation as a potential exposure pathway in its risk calculations. Water ingestion, dermal absorption when showering and indoor inhalation were the three most predominant contributing exposure pathways for risk development among sites contaminated by VOCs. On the other hand, crop and meat ingestion were more important exposure pathways in the context of sites with non-VOC pollutants, because these hydrophobic contaminants may be bio-accumulative in plants and animals, and consequently enter the human body via food chains.

The Health Risk assessment of Pb and Cr leached from fly ash monolith landfill.

As of 2004, nearly two hundred thousand tons of fly ash monoliths are created each year in Taiwan to confine heavy metals for reducing the leaching quantity by precipitation. However, due to abnormal monolith fracture, poorly liner quality or exceeding usage over designed landfill capacity, serious groundwater pollution of the landfills has been reported. This research focuses on Pb and Cr leaching from monolithic landfill to assess the risk of groundwater pollution in the vicinity. The methodology combines water budget simulations using HELP model with fate and risk simulations using MMSOILS model for 5 kinds of landfill structures and 2 types of leaching models, and calculates the risk distribution over 400 grids in the down gradient direction of groundwater. The results demonstrated that the worst liner quality will cause the largest risk and the most significant exposure pathway is groundwater intake, which accounted for 98% of the total risk. Comparing Pb and Cr concentrations in the groundwater with the drinking water standards, only 14.25% of the total grids are found to be under 0.05 mg/L of Pb, and over 96.5% of the total grids are in the safety range of Cr. It indicates that Pb leaching from fly ash monolithic landfills may cause serious health risks. Without consideration of the parameters uncertainty, the cancer and noncancer risk of Pb with the sanitary landfill method was 4.23E-07 and 0.63, respectively, both under acceptable levels. However, by considering the parameters uncertainty, the non-carcinogenic risk of Pb became 1.43, exceeding the acceptable level. Only under the sealed landfill method was the hazard quotient below 1. It is important to use at least the sealed landfill for fly ash monoliths containing lead to effectively reduce health risks.

Identification of pollution source of cadmium in soil: application of material flow analysis and a case study in Taiwan.

BACKGROUND: Since the 1970s, at least 200 hectares (ha) of farm-land has been polluted by the heavy metal cadmium (Cd). Consequently, the Cd pollution has led to contaminate the rice production and caused acute social panic. According to the recent investigation results performed by the Taiwan Environmental Protection Administration (TEPA), it is indicated that most of the Cd pollution incidents in Taiwan resulted from the waste-water discharge of stearate Cd factories. To prevent the Cd pollution incidents from spreading, the TEPA has either forced these factories to close down or assisted them in improving their production processes since the 1980s. Unfortunately, accidental incidents of Cd pollution still emerge in an endless stream, despite the strict governmental controls placed on these questionable factories. Whether this pollution has resulted from undetected or hidden pollution sources stemming from two decades ago or comes from some new source, will be an outstanding issue. Therefore, this study attempts to identify the pollution sources of Cd in soil in Taiwan as well as to find the solution to the above-mentioned, outstanding issue by way of a methodology termed Material Flow Analysis (MFA). METHODOLOGY: The MFA has proved to be a useful tool on providing quantitative information of the flow of substances through an economic to an environmental system. Based upon the supply-and-demand theory of MFA, researchers have successfully conducted an overview of the use of materials in many industries, the construction industry being one of these. Therefore, this study tries to establish a set of analytical processes by way of MFA for identifying the pollution source of Cd in soil in Taiwan. In addition, the spirit of Life Cycle Assessment (LCA) technique was also employed to identify the materials, and products should be ignored as a crucial pollution source in this study. RESULTS AND DISCUSSION: According to the MFA methodology applied in this study and on the basis of related studies performed by Taiwanese governmental authorities, we arrive at the following analysis results: (1) the total amount of Cd from the economic perspective of material and product flow was approximately 441.2 tons; (2) the wastewater directly discharged into irrigation water can be concluded to be the major pollution route of Cd in farmland soil in Taiwan; (3) material plastic stabilizer (cadmium oxide, CdO), Zn-Pd compounds and Cu compounds should be the crucial pollution sources to contaminate environment through the route of wastewater in Cd flow analysis; (4) the crucial pollution sources to contaminate environment through the route of wastewater in Cd flow analysis were five factories, Coin, Jili, Taiwan Dye, Guangzheng and Mingguan, and they were all categorized as stearate Cd industries; (5) the typical source of the Cd pollution in soil in Changhua County through the pollution route of wastewater should be the metal surfacing process industries. CONCLUSIONS: This study proved that MFA can be a good tool for identifying Cd flow as well as for recognizing the crux of the problem concerning incidents of Cd pollution. This study led to the conclusion that the causal relationship between farmland pollution caused by Cd and stearate Cd factories in Taiwan seemed quite close by way of MFA methodology. In addition, this study also found that the wastewater discharged from a single metal surfacing process factory will not cause remarkable farmland pollution. However, the wastewater simultaneously discharged from a group of pollution factories can result in a significant pollution incident. RECOMMENDATIONS AND OUTLOOK: This case study is only a small contribution to the understanding of the toxic material flow related to Cd in the environment. This study recommends that Taiwanese governmental authorities should not deal with problems on an ad hoc basis, but should instead deal with Cd pollution problems overall employing control measures. Finally, the more accurate information or data we can collect, the more reliable results we can identify. Therefore, the quality and quantity of related data used in this MFA model should be closely scrutinized in order to ensure the most correct and comprehensive investigation on the toxic material flow.

Oxidation of methyl methacrylate from semiconductor wastewater by O3 and O3/UV processes.

This study investigated the oxidation of methyl methacrylate (MMA) by sole ozonation and ozone/UV treatments. The semi-batch ozonation experiments were proceeded under different reaction conditions to study the effects of ozone dosage and UV radiation on the oxidation of MMA. The experimental results indicated that both the oxidation of MMA by the sole ozonation and O3/UV processes can completely decompose MMA to form the following intermediates within 30 min reaction time. To increase the applied ozone dosage can significantly raise the removal efficiency of MMA. However, the mineralization of MMA via the direct oxidation reaction of molecular ozone was slow, while introducing the UV radiation can promote the mineralization rate of MMA. In addition, the pH value of the oxidized solution in the O3/UV treatment decreased lower than that in the sole ozonation treatment of about 1 unit. The possible scheme of the decomposition pathway of MMA under the ozonation process is proposed in this study. Formic acid and acetic acid were found to be the main ozonated intermediates.

Site-specific health risk assessment of dioxins and furans in an industrial region with numerous emission sources.

While the sources of releasing dioxins have received much attention, the health risks of incinerators are studied considerably more than those of other sources, such as metallurgical industry. Furthermore, risk assessments focus primarily on the effects of single sources; few have addressed the aggregate risks from multiple sources in a region. When many sources of dioxins exist in an area, such as the Industrial Park located in the densely populated district-Siaogang District in southern Taiwan where 17 primary known PCDD/F stationary emission sources are clustered, is the aggregate exposure to these sources imposing high risks even though individual sources comply with emission standards? The study combined the multimedia and multiple pathway exposure modeling and site-specific exposure scenario to assess dioxin risks contributed by the 17 emission sources in the District, including municipal waste incinerators, medical waste incinerators, sinter plants, electric arc furnace, secondary aluminum smelters, cement kilns, etc. The average cancer risk of a resident living in the District was found to be 3.43E-04 under the site-specific exposure scenario. The top emission source is the sinter plant, followed by the electric arc furnace. The information has driven the local government to conduct more complete assessment and at the same time to consider enforcing a stricter local standard of dioxin emissions in the Siaogang District.

The effectiveness of a new gas-induced reactor in treating phenolic wastewater by ozonation and hydrogen peroxide.

A new Gas-Induced Reactor (GIR) has been developed to improve the efficiency of ozone utilization in water treatment. In this study, the GIR was used to investigate the behavior of ozonation of aqueous phenol solution by means of O3 and O3/H2O2 processes in order to explore the feasibility and efficiency of treating such wastewater using the new GIR. The study observed the decomposition of phenol, utilization of ozone, and variation of TOC during ozonation, varying pH values, phenol initial concentrations, ozone input concentrations, and hydrogen peroxide dosages. The study concluded that the new GIR was capable of performing effective and efficient ozonation of phenolic wastewater, maintaining high ozone utilization ratios at all experimental pH values and initial phenol and ozone concentrations. The optimal pH condition for phenol removal was around 11. The best molar ratios of initial hydrogen peroxide over input ozone among the performed experiments were about 20 at pH 7 and 10 at pH 9 and 11. The primary operational energy used for treating a tonne of wastewater was 66 MJ, giving treatment costs of about USS1.0 per tonne.

Using stochastic risk assessment in setting information priorities for managing dioxin impact from a municipal waste incinerator.

The objectives of this study were to assess site-specific carcinogenic risk of incinerator-emitted dioxins in a manner reflecting pollutant transfer across multimedia and multi-pathways. The study used site-specific environmental and exposure information and combined the Monte Carlo method with multimedia modeling to produce probability distributions of risk estimates. The risk estimates were further categorized by contaminated environmental media and exposure pathways that are experienced by human receptors in order to pinpoint significant sources of risk. Rank correlation coefficients were also calculated along with the Monte Carlo sampling to identify key factors that influenced estimation of risk. The results showed that ingestion accounted for more than 90% of the total risk and that risk control on ingestion of eggs, aboveground vegetables, and poultry should receive priority. It was also found that variation of parameters with variability accounted for around 35% of the total risk variance, while uncertainty contributed to the remaining 65%. Intake rates of aboveground vegetables, eggs, and poultry were the key parameters with the largest contribution to variance. In addition, sufficient sampling and analysis of dioxin contents in eggs, aboveground vegetables, poultry, soil, and fruit should be performed to improve risk estimation because the variation in concentrations in these media accounted for the largest overall risk variance. Finally, focus should be placed on reduction of uncertainty associated with the risk estimation through ingestion of aboveground vegetables, eggs, poultry, fruit, and soil because the risk estimates associated with these exposure pathways had the largest variance.

Transfer of dioxin risk between nine major municipal waste incinerators in Taiwan.

The objective of this study was to assess site-specific carcinogenic risks of incinerator-emitted dioxins and risk transfers among the areas covered by nine municipal incinerators in Taiwan. We used actual emission data and the industrial source complex short-term model (ISCST3) to determine the dioxin impact areas within the 8 x 8-km simulation regions surrounding the incinerators. We then used multimedia model to estimate cancer risks in individual impact areas for two exposure scenarios, which were sufficient (SFP) and insufficient food production (IFP) for residents' consumption in each impact area. We also used information of food supply and consumption between impact areas to calculate risk transfers among these nine incinerators. We found that dioxins' carcinogenic risks ranged from 1.4 x 10(-8) (Incinerator F) to 7.1 x 10(-5) (Incinerator A) for the nine incinerators under the exposure scenario of SFP, and ranged from 8.7 x 10(-8) (Incinerator D) to 1.1 X 10(-6) (Incinerator E) under the exposure scenario of IFP. The food ingestion was the main exposure pathway, which accounted for 64-99% of total dioxin risks among nine impact areas. For the nine major food items consumed by residents in the impact areas, eggs (14-35%) and chicken (11-26%) were two main routes of dioxin exposure in the SFP scenario, while chicken (8-78%) and vegetables (0.2-81%) were two main routes of dioxin exposure in the IFP scenario. Significant risks of dioxins were transferred among incinerators, which accounted for up to 88% among the incinerators. Incinerator E was the major risk-exporting source to six Incinerators C, D, F, G, H, and I. For these six incinerators, Incinerator E accounted for their 51-88% imported risks. We concluded that risk transfers among incinerators through routes of food consumption should be considered in assessing health risks associated with incinerator-emitted dioxins in Taiwan. We should place high priority on implementing control measures to lower dioxin emissions in important food-exporting areas like Incinerator E. We should also emphasize analyzing dioxin contents in eggs, chicken, and vegetables in order to improve dioxin-related health risk assessments in the future.