Stable Acidic Water Oxidation with a Cobalt-Iron-Lead Oxide Catalyst Operating via a Cobalt-Selective Self-Healing Mechanism.

The instability and expense of anodes for water electrolyzers with acidic electrolytes can be overcome through the implementation of a cobalt-iron-lead oxide electrocatalyst, [Co-Fe-Pb]Ox , that is self-healing in the presence of dissolved metal precursors. However, the latter requirement is pernicious for the membrane and especially the cathode half-reaction since Pb2+ and Fe3+ precursors poison the state-of-the-art platinum H2 evolving catalyst. To address this, we demonstrate the invariably stable operation of [Co-Fe-Pb]Ox in acidic solutions through a cobalt-selective self-healing mechanism without the addition of Pb2+ and Fe3+ and investigate the kinetics of the process. Soft X-ray absorption spectroscopy reveals that low concentrations of Co2+ in the solution stabilize the catalytically active Co(Fe) sites. The highly promising performance of this system is showcased by steady water electrooxidation at 80±1 °C and 10 mA cm-2 , using a flat electrode, at an overpotential of 0.56±0.01 V on a one-week timescale.

Thin films of poly(vinylidene fluoride-co-hexafluoropropylene)-ionic liquid mixtures as amperometric gas sensing materials for oxygen and ammonia.

Gas sensors are important devices used to monitor the type and amount of gas present. Amperometric gas sensors - based on measuring the current upon an applied potential - have been progressing towards miniaturised designs that are smaller, lower cost, faster responding and more robust compared to commercially available sensors. In this work, a planar thin-film electrode device is employed for gas sensing with a thin layer of gel polymer electrolyte (GPE). The GPE consists of a room temperature ionic liquid (RTIL, with two different imidazolium cations and the tetrafluoroborate [BF4]- anion) mixed with poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP). The polymer acts as a scaffold, with the RTIL ions able to flow within the porous percolated channels, resulting in a highly robust gel with high conductivity. The chemical nature of the polymer allows thin-films (ca. 6 µm) to be evenly dropcast onto planar electrode devices, using minimal amounts of material. Remarkably, no significant effect of resistance was observed in the voltammetric response with such thin films. Oxygen (O2) and ammonia (NH3) gases were detected in the concentration ranges 1-20% O2 and 1-10 ppm NH3 in the two GPEs using both linear sweep voltammetry (LSV) and long-term chronoamperometry (LTCA). LTCA was the preferred detection method for both gases due to the steady-state current response compared to the sloping current response from LSV. The thin nature of the film gave fast response times for both gases - less than 10 seconds for O2 and ca. 40 seconds for NH3 - easily rivaling the commercially available porous electrode designs and allowing for continuous monitoring of gas concentrations. These materials appear to be highly promising candidates as gas detection electrolytes in miniaturised devices, with accurate and fast responses in both the cathodic and anodic potential regions.

Preparation of chiral graphene oxides by covalent attachment of chiral cysteines for voltammetric recognition of tartrates.

The authors describe the preparation of a chiral graphene oxides (GOs) by covalent attachment of D- or L-cysteine using a one-step hydrothermal method. The resulting chiral functionalized GOs shows circular dichroism with intensities similar to those produced by the cysteines. This indicates that the chirality of cysteines is well preserved in the chiral GOs. The material is reasonably stable at temperatures from 20 to 200 °C and at pH values from 0 to 14. A glassy carbon electrode (GCE) was modified with the chiral GOs and then tested for recognition capability for L- and D-tartrate (0.5 mM). The enantioselectivity of the chiral GOs appears to be the result of a synergistic effect where GO increases the conductivity and cysteine provides the chiral environment. The method is assumed to provide a useful general scheme for development of advanced carbonaceous materials with chiral recognition capabilities. Graphical abstract Chiral graphene oxides produced by covalently attaching chiral amino acids displays effective enantioselective recognition. Graphical abstract contains poor quality of text inside the artwork. Please do not re-use the file that we have rejected or attempt to increase its resolution and re-save. It is originally poor, therefore, increasing the resolution will not solve the quality problem. We suggest that you provide us the original format. We prefer replacement figures containing vector/editable objects rather than embedded images. Preferred file formats are eps, ai, tiff and pdf.We have uploaded the modified version as Graphical abstract.

Hydrogen bonding effect between active site and protein environment on catalysis performance in H2-producing [NiFe] hydrogenases.

The interaction between the active site and the surrounding protein environment plays a fundamental role in the hydrogen evolution reaction (HER) in [NiFe] hydrogenases. Our density functional theory (DFT) findings demonstrate that the reaction Gibbs free energy required for the rate determining step decreases by 7.1 kcal mol-1 when the surrounding protein environment is taken into account, which is chiefly due to free energy decreases for the two H+/e- addition steps (the so-called Ni-SIa to I1, and Ni-C to Ni-R), being the largest thermodynamic impediments of the whole reaction. The variety of hydrogen bonds (H-bonds) between the amino acids and the active site is hypothesised to be the main reason for such stability: H-bonds not only work as electrostatic attractive forces that influence the charge redistribution, but more importantly, they act as an electron 'pull' taking electrons from the active site towards the amino acids. Moreover, the electron 'pull' effect through H-bonds via the S- in cysteine residues shows a larger influence on the energy profile than that via the CN- ligands on Fe.

Task-specific thioglycolate ionic liquids for heavy metal extraction: Synthesis, extraction efficacies and recycling properties.

Eight novel task-specific ionic liquids (TSILs) based on the thioglycolate anion designed for heavy metal extraction have been prepared and characterized by 1H and 13C NMR, UV-Vis, infrared, ESI-MS, conductivity, viscosity, density and thermal properties. Evaluation of their time-resolved extraction abilities towards cadmium(II) and copper(II) in aqueous solutions have been investigated where distribution ratios up to 1200 were observed. For elucidation of the IL extraction mode, crystals were grown where Cd(II) was converted with an excess of S-butyl thioglycolate. It was found by X-ray diffraction analysis that cadmium is coordinated by five oxygen and one sulfur donor atoms provided by two thioglycolate molecules and one water molecule. Leaching behavior of the hydrophobic ionic liquids into aqueous systems was studied by TOC (total dissolved organic carbon) measurements. Additionally, the immobilization on polypropylene was elucidated and revealed slower metal extraction rates and similar leaching behavior. Finally, recovery processes for cadmium and copper after extraction were performed and recyclability was successfully proven for both metals.

A novel class of gas separation membrane based on organic ionic plastic crystals.

The first use of organic ionic plastic crystals (OIPCs) as CO2 separation membranes is reported. The novel OIPC/PVDF nanofiber composites show CO2/N2 ideal selectivities of 30 at 35 °C. The dependence of gas permeability on the thermal phase of the plastic crystals is discussed.

Why is a proton transformed into a hydride by [NiFe] hydrogenases? An intrinsic reactivity analysis based on conceptual DFT.

The hydrogen evolution reaction (HER) catalysed by [NiFe] hydrogenases entails a series of chemical events involving great mechanistic interest. In an attempt to understand and delve into the question about 'Why does nature work in that way?', an in-depth intrinsic reactivity analysis based on conceptual DFT has been carried out focusing on the so-called to step, i.e. our work tries to answer how and why the proton attached to the reactive sulphur atom from one of the exo-cyclic cysteine residues is transformed into a bridging hydride to be shared between the Ni/Fe metals in the active site of [NiFe] hydrogenases, which involves not only H migration, but also a change of the charge state on Ni from Ni(i) to Ni(iii). Our DFT results suggest that the transformation is motivated by spontaneous rearrangements of the electron density, and stabilisation comes from the decrease of both electronic activity and electrophilicity index from Ni.

An intensified π-hole in beryllium-doped boron nitride meshes: its determinant role in CO2 conversion into hydrocarbon fuels.

DFT investigations on beryllium-doped boron nitride meshes or sheets (BNs) predict the existence of a very reactive kind of novel material capable of spontaneously reducing the first hydrogenation step in the CO2 conversion mechanism. This impressive behaviour appears as a result of the very deep π-hole generated by the beryllium moieties, and also determines its selectivity towards the production of CH4.

Inhibited fragmentation of mAbs in buffered ionic liquids.

We thoroughly investigated the biological, structural and chemical stability of epidermal growth factor receptor monoclonal antibody (EGFR mAb) using choline-based buffered ionic liquids (BILs). The results demonstrated substantially enhanced stabilities in our BILs, indicating their huge promise as real-world green biological buffers for antibody storage and transportation.

Biocompatible ionic liquid-biopolymer electrolyte-enabled thin and compact magnesium-air batteries.

With the surge of interest in miniaturized implanted medical devices (IMDs), implantable power sources with small dimensions and biocompatibility are in high demand. Implanted battery/supercapacitor devices are commonly packaged within a case that occupies a large volume, making miniaturization difficult. In this study, we demonstrate a polymer electrolyte-enabled biocompatible magnesium-air battery device with a total thickness of approximately 300 µm. It consists of a biocompatible polypyrrole-para(toluene sulfonic acid) cathode and a bioresorbable magnesium alloy anode. The biocompatible electrolyte used is made of choline nitrate (ionic liquid) embedded in a biopolymer, chitosan. This polymer electrolyte is mechanically robust and offers a high ionic conductivity of 8.9 × 10(-3) S cm(-1). The assembled battery delivers a maximum volumetric power density of 3.9 W L(-1), which is sufficient to drive some types of IMDs, such as cardiac pacemakers or biomonitoring systems. This miniaturized, biocompatible magnesium-air battery may pave the way to a future generation of implantable power sources.

Ionic liquids as antiwear additives in base oils: influence of structure on miscibility and antiwear performance for steel on aluminum.

The use of ionic liquids as additives to base oil for the lubrication of steel on aluminum was investigated. The miscibility and wear performance of various phosphonium, imidazolium, and pyrrolidinium ionic liquids in a range of polar and nonpolar base oils was determined. The structure and ion pairing of the ionic liquids was found to be important in determining their miscibility in the base oils. In wear tests, some of the miscible base oil/IL blends reduced the aluminum wear depth when compared to that found with the base oil alone. The nonpolar base oil/IL blends were able to withstand higher wear-test loads than the polar base oil/IL blends. At 10 N, as little as 0.01 mol/kg of IL, or 0.7-0.9 wt %, in the nonpolar base oils was enough to drastically reduce the wear depth on the aluminum. XPS analysis of the wear surfaces suggested that the adsorbing of the IL to the surface, where it can form low-shear layers and also react to form tribofilms, is important in reducing friction and wear. The largest reductions in wear at the highest load tested were found for a mineral oil/P6,6,6,14 (i)(C8)2PO2 blend.

A comparison of phosphorus and fluorine containing IL lubricants for steel on aluminium.

Ionic liquids have been shown to be highly effective lubricants for a steel on aluminium system. This work shows that the chemistry of the anion and cation are critical in achieving maximum wear protection. The performance of the ILs containing a diphenylphosphate (DPP) anion all showed low wear, as did some of the tris(pentafluoroethyl)trifluorophosphate (FAP) and bis(trifluoromethanesulfonyl)amide (NTf(2)) anion containing ILs. However, in the case of the FAP and NTf(2) based systems, a cation dependence was observed, with relatively poor wear resistance obtained in the case of an imidazolium FAP and two pyrrolidinium NTf(2) salts, probably due to tribocorrosion caused by the fluorine reaction with the aluminium substrate. The systems exhibiting poor performance generally had a lower viscosity, which also impacts on their tribological properties. Those ILs that exhibited low wear were shown to have formed protective tribofilms on the aluminium alloy surface.

In vitro assessment of choline dihydrogen phosphate (CDHP) as a vehicle for recombinant human interleukin-2 (rhIL-2).

Choline dihydrogen phosphate (CDHP) is an ionic liquid reported to increase thermal stability of model proteins. The current work investigated CDHP effect on structural integrity and biological activity of recombinant human interleukin-2 (rhIL-2), a therapeutic protein used for treating advanced melanoma. In vitro CDHP biocompatibility was also evaluated using primary cell cultures, or B16-F10 cell line, chronically exposed to the ionic liquid. Formulation of rhIL-2 in an aqueous 680mM CDHP pH 7.4 solution resulted in a 12.5°C increase in the Tm of rhIL-2 compared to a basic buffer formulation, and provided conformational rhIL-2 stabilization when the solution was heated to 23.3°C above the Tm. CDHP solutions (≤80mM), exhibited no cytotoxic activity toward primary splenocytes or B16-F10 cells in culture. However, a 10-fold loss in biological activity was observed when rhIL-2 was used in a 30mM CDHP aqueous solution with NaHCO3 (pH≥7.2) compared to controls without CDHP. While increased Tm is associated with a diminished rhIL-2 biological activity, the therapeutic protein remains structurally intact and functional.

Choline dihydrogen phosphate.

In the cystal structure of the title compound, (2-hy-droxy-ethyl)trimethylammonium dihydrogen phosphate, C(5)H(14)NO(+)·H(2)PO(4) (-), two anions create dimeric structures via two O-H⋯O hydrogen bonds. The hydrogen-bonded dimers are connected by another O-H⋯O hydrogen bond with the hydroxyl groups of the cations, constructing a columner structure along the a axis. A number of C-H⋯O interactions are also present.

Use of ionic liquids for pi-conjugated polymer electrochemical devices.

pi-Conjugated polymers that are electrochemically cycled in ionic liquids have enhanced lifetimes without failure (up to 1 million cycles) and fast cycle switching speeds (100 ms). We report results for electrochemical mechanical actuators, electrochromic windows, and numeric displays made from three types of pi-conjugated polymers: polyaniline, polypyrrole, and polythiophene. Experiments were performed under ambient conditions, yet the polymers showed negligible loss in electroactivity. These performance advantages were obtained by using environmentally stable, room-temperature ionic liquids composed of 1-butyl-3-methyl imidazolium cations together with anions such as tetrafluoroborate or hexafluorophosphate.