Canister valve and actuator deposition in metered dose inhalers formulated with low-GWP propellants.

A challenge in pressurised metered-dose inhaler (pMDI) formulation design is management of adhesion of the drug to the canister wall, valve and actuator internal components and surfaces. Wall-material interactions differ between transparent vials used for visual inspection and metal canister pMDI systems. This is of particular concern for low greenhouse warming potential (GWP) formulations where propellant chemistry and solubility with many drugs are not well understood. In this study, we demonstrate a novel application of X-ray fluorescence spectroscopy using synchrotron radiation to assay the contents of surrogate solution and suspension pMDI formulations of potassium iodide and barium sulphate in propellants HFA134a, HFA152a and HFO1234ze(E) using aluminium canisters and standard components. Preliminary results indicate that through unit life drug distribution in the canister valve closure region and actuator can vary significantly with new propellants. For solution formulations HFO1234ze(E) propellant shows the greatest increase in local deposition inside the canister valve closure region as compared to HFA134a and HFA152a, with correspondingly reduced actuator deposition. This is likely driven by chemistry changes. For suspension formulations HFA152a shows the greatest differences, due to its low specific gravity. These changes must be taken into consideration in the development of products utilising low-GWP propellants.

Development of excipients free inhalable co-spray-dried tobramycin and diclofenac formulations for cystic fibrosis using two and three fluid nozzles.

This study aims to investigate the effect of physicochemical properties and aerosol performance of two (2FN) and three-fluid nozzles (3FN) on the inhalable co-formulation of tobramycin and diclofenac dry powders. Combination formulations of tobramycin and diclofenac at 2:1 and 4:1 w/w ratios were prepared at a laboratory scale using a spray dryer in conjunction with a 2FN or 3FN. Powder size, morphology, solid-state characteristics, and aerodynamic and dissolution properties were characterised. The nozzle types and the formulation composition influenced the yield, particle size, solid-state properties, aerosolization behaviour and dissolution of the co-spray dried formulations. In particular, using the 2FN the co-spray dried formulation of tobramycin and diclofenac at 2:1 w/w showed smaller particle size (D50, 3.01 ± 0.06 µm), high fine particle fractions (FPF) (61.1 ± 3.6% for tobramycin and 65.92 ± 3 for diclofenac) and faster dissolution with approx. 70% diclofenac released within 3 h and approx. 90% tobramycin was released within 45 min. However, the 3FN for the co-spray dried formulation of tobramycin and diclofenac at a 2:1 w/w ratio showed a larger particle size (D50, 3.42 ± 0.02 µm), lower FPF (40.6 ± 3.4% for tobramycin and 36.9 ± 0.84 for diclofenac) and comparative slower dissolution with approx. 60% diclofenac was released within 3 h and 80% tobramycin was released within 45 min. A similar trend was observed when the tobramycin to diclofenac ratio was increased to 4:1 w/w. Overall results suggest that spray drying with 2FN showed a superior and viable approach to producing excipients-free inhalable co-spray dried formulations of tobramycin and diclofenac. However, the formulation produced using the 3FN showed higher enrichment of hydrophobic diclofenac and an ability to control the tobramycin drug release in vitro.

Structure-activity relationship of lipid core peptide-based Group A Streptococcus vaccine candidates.

Infection with Group A Streptococcus (GAS) can result in a range of different illnesses, some of which are fatal. Currently, our efforts to develop a vaccine against GAS focuses on the lipid core peptide (LCP) system, a subunit vaccine containing a lipoamino acid (LAA) moiety which allows the stimulation of systemic antibody activity. In the present study, a peptide (J14) representing the B-cell epitope from the GAS M protein was incorporated alongside a universal T-helper epitope (P25) in four LCP constructs of different spatial orientation or LAA lengths. Through structure-activity studies, it was discovered that while the alteration of the LCP orientation had a weaker effect on immunostimulation, increasing the LAA side chain length within the construct increased antibody responses in murine models. Furthermore, the mice immunised with the lead LCP construct were also able to maintain antibody activity throughout the course of five months. These findings highlight the importance of LAA moieties in the development of intranasal peptide vaccines and confirmed that its side chain length has an effect on the immunogenicity of the structure.

Development of docetaxel-loaded solid self-nanoemulsifying drug delivery system (SNEDDS) for enhanced chemotherapeutic effect.

The main purpose of this study was to investigate the potential of self-nano-emulsifying drug delivery system (SNEDDS) in improving the bioavailability of docetaxel (DCT) and its chemotherapeutic effect. The DCT-loaded SNEDDS was prepared by employing rational blends of capryol 90, labrasol, and transcutol HP using ternary phase diagram. The liquid nano-emulsion was spray-dried into solid SNEDDS (D-SNEDDS) using an inert porous carrier, colloidal silica. The optimized formulation was characterized in terms of physico-chemical and pharmacokinetic parameters. Furthermore, anti-tumor efficacy of D-SNEDDS was compared with commercial marketed product, Taxotere(®). The various compositions of SNEDDS were screened and found optimal at a volume ratio of 10/75/15 for capryol 90, labrasol, and transcutol HP, respectively. We observed a high oral bioavailability of 17% DCT for D-SNEDDS than compared to only 2.6% for pure DCT solution. Notably, D-SNEDDS exhibited an augmented anti-tumor efficacy with a reduced toxicity profile when compared with intravenously administered Taxotere(®), the commercialized formulation of DCT. Taken together, D-SNEDDS could be a potential candidate for an oral dosage form of DCT with enhanced antitumor activity and reduced toxicity.

A novel surface-attached carvedilol solid dispersion with enhanced solubility and dissolution.

A novel surface-attached, spray-dried solid dispersion containing poorly water-soluble carvedilol (CV) without any change in the crystallinity was prepared using water, polyvinylpyrrolidone (PVP K30) and Tween 80. The solid dispersion was optimized by investigating the effects of the weight ratios of Tween 80/PVP K30 and carrier/drug on the aqueous solubility of CV. The optimum solid dispersion consisted of a relatively low carrier to drug weight ratio: the weight ratio of CV/PVP K30/Tween 80 was 12/4/2. Unlike conventional methods of solid dispersion preparation, this method yielded CV-loaded solid dispersion with no change in the crystallinity of the drug as was evident from SEM, DSC and XRD. It was demonstrated that the solid dispersions prepared had hydrophilic carriers attached to the surface of the drug, thus changing it from a hydrophobic to a hydrophilic form without changing the crystalline form. The optimized solid dispersion improved the drug solubility and dissolution rate by about 11,500-fold and twofold, respectively. It was further suggested that this method of solid dispersion preparation is better than conventional methods in terms of environmental and industrial standpoints. Thus, it was concluded that CV-loaded solid dispersion prepared using this method would be of use for delivering poorly water-soluble CV with enhanced solubility and dissolution, but without crystalline changes.

Development of raloxifene-solid dispersion with improved oral bioavailability via spray-drying technique.

The purpose of this study was to develop a raloxifene-loaded solid dispersion with enhanced dissolution rate and bioavailability via spray-drying technique. Solid dispersions of raloxifene (RXF) were prepared with PVP K30 at weight ratios of 1:4, 1:6 and 1:8 using a spray-drying method, and characterized by differential scanning calorimetry, X-ray powder diffraction, scanning electron microscopy, and solubility and dissolution tests. The bioavailability of the solid dispersion in rats was also evaluated compared to those of RXF powder and commercial product. Results showed that the RXF-loaded solid dispersion was in amorphous form with increased solubility and dissolution rate. The absorption of RXF from solid dispersion resulted in approximately 2.6-fold enhanced bioavailability compared to pure drug. Moreover, RXF-loaded solid dispersion gave similar AUC, C(max) and T(max) values to the commercial product, suggesting that it was bioequivalent to the commercial product in rats. These findings suggest that an amorphous solid dispersion of RXF could be a viable option for enhancing the oral bioavailability of RXF.

Preparation and evaluation of raloxifene-loaded solid dispersion nanoparticle by spray-drying technique without an organic solvent.

The aim of this study was to improve the physicochemical properties and bioavailability of a poorly water-soluble drug, raloxifene by solid dispersion (SD) nanoparticles using the spray-drying technique. These spray-dried SD nanoparticles were prepared with raloxifene (RXF), polyvinylpyrrolidone (PVP) and Tween 20 in water. Reconstitution of optimized RXF-loaded SD nanoparticles in pH 1.2 medium showed a mean particle size of approximately 180 nm. X-ray diffraction and differential scanning calorimetry indicated that RXF existed in an amorphous form within spray-dried nanoparticles. The optimized formulation showed an enhanced dissolution rate of RXF at pH 1.2, 4.0, 6.8 and distilled water as compared to pure RXF powder. The improved dissolution of raloxifene from spray-dried SD nanoparticles appeared to be well correlated with enhanced oral bioavailability of raloxifene in rats. Furthermore, the pharmacokinetic parameters of the spray-dried SD nanoparticles showed increased AUC(0-∞) and C(max) of RXF by approximately 3.3-fold and 2.3-fold, respectively. These results suggest that the preparation of RXF-SD nanoparticles using the spray drying technique without organic solvents might be a promising approach for improving the oral bioavailability of RXF.

Physicochemical characterization and in vivo evaluation of solid self-nanoemulsifying drug delivery system for oral administration of docetaxel.

To formulate a self-nanoemulsifying drug delivery system (SNEDDS) for the oral administration of docetaxel as an alternative to commercial docetaxel-loaded injectable products, it was prepared by spray-drying an aqueous solution containing liquid SNEDDS and colloidal silica. Its physicochemical properties and oral bioavailability were investigated compared to a clear docetaxel solution administered intravenously or orally to rats. In the docetaxel-loaded solid SNEDDS prepared with colloidal silica, the liquid SNEDDS composed of Capryol 90, Cremophore EL and Transcutol HP (45/35/20, volume ratio) was absorbed inside the pores of carriers, and docetaxel was present in a changed amorphous state. The solid SNEDDS with 3.3% (w/v) docetaxel produced nanoemulsions, and showed about 12.5% absolute bioavailability in rats. Thus, this solid SNEDDS may be a potential candidate for oral pharmaceutical product with improved oral bioavailability of docetaxel.

Fabrication and evaluation of pH-modulated solid dispersion for telmisartan by spray-drying technique.

The present study was undertaken to overcome the problems associated with solubility, dissolution and oral bioavailability of a poorly water-soluble ionizable drug, telmisartan (TMS). For these purposes, a solubility test was carried to select the appropriate formulation composition from various carriers and alkalizers. Solid dispersions (SDs) of TMS were prepared at different drug-to-carrier ratios by the spray-drying technique, and were characterized by dissolution and aqueous solubility studies. The optimum formulation was investigated by dissolution studies at different pH and water media and its solid state characterisations were performed by scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and X-ray diffraction (XRD) studies. In solubility and dissolution tests, all TMS-loaded pH-modulated SDs (pH(M)-SDs) exhibited marked improvement in the dissolution behavior when compared with crystalline TMS powder. The optimum formulation of pH(M)-SD consisted of TMS/PVP (polyvinylpyrrolidone) K30/Na(2)CO(3) at a weight ratio of 2/0.5/3 and showed significant improvement in the aqueous solubility and dissolution rate by approximately 40,000- and 3-fold, respectively, compared to TMS powder. Solid-state characterization revealed the changed in crystallinity of TMS into amorphous state. Furthermore, area under the drug concentration time-curve (AUC) of TMS from the pH(M)-SD increased by 13.4- and 2.1-fold, compared with TMS powder and commercial product, respectively. According to these observations, taken together with dissolution and pharmacokinetic behaviors, pH-modulated SD in the presence of an alkalizer for a poorly water-soluble ionizable drug, TMS, appeared to be efficacious for enhancing its bioavailability.

Effect of dose and dosage interval on the oral bioavailability of docetaxel in combination with a curcumin self-emulsifying drug delivery system (SEDDS).

The present study investigated the effects of a curcumin self-emulsifying drug delivery systems (SEDDS) on the pharmacokinetics of orally administered docetaxel in rats. A single dose of docetaxel was orally administered (30 mg/kg) alone or after oral curcumin SEDDS (25, 50, 100 and 150 mg/kg) administration with time intervals of 0, 15 and 30 min, respectively. After oral administration, the C (max) and the area under the plasma concentration-time curve (AUC) of docetaxel were significantly increased (0 min, p < 0.05; 15 and 30 min, p < 0.01) by 2.2, 4.7 and 4.6 times and 2.0, 3.8 and 4.1 times compared to that of control group, respectively, after treatment with curcumin SEDDS (100 mg/kg) for each interval. Moreover, The C (max) of docetaxel was increased by 2.6 and 4.4 times in response to 25 and 50 mg/kg curcumin SEDDS treatment, respectively, the corresponding AUC was increased by about 2.4 and 3.1 times, and consequently the absolute bioavailabilities of docetaxel in these two treatment groups were 7.9 and 10.4%, respectively, which showed a significant increase of about 2.4- and 3.2-fold in comparison to the control value (3.3%). However, no further increase in either AUC or C (max) values of docetaxel was observed as the curcumin SEDDS dose was increased from 50 to 150 mg/kg. It is worth noting that the presence of curcumin SEDDS did not significantly decrease the systemic clearance, which was shown by the almost unchanged terminal half-life (t (1/2)) of docetaxel in all treatment groups. Thus, the enhanced bioavailability of oral docetaxel by curcumin SEDDS seemed to be likely due to an inhibition function of cytochrome P450 (CYP) 3A and P-glycoprotein (Pgp) in the intestines of the rats. However, further in vivo studies are needed to verify these hypotheses.