Preventing varus collapse in proximal humerus fracture fixation: 90-90 dual plating versus endosteal fibular allograft strut.

INTRODUCTION: Screw cut out and varus collapse are the most common complication of locked plate fixation of proximal humerus fractures. The purpose of this study was to compare dual plating and endosteal fibular allograft struts as augmentation strategies to prevent varus collapse. MATERIALS AND METHODS: A trapezoidal osteotomy was created at the metaphysis to create a 2-part proximal humerus model in 18 paired shoulder specimens. Each specimen was assigned to group A, B, or C and was fixed with either a lateral locking plate, a lateral locking plate and anterior one-third tubular plate in an orthogonal 90/90 configuration, or a lateral locking plate with intramedullary fibular strut, respectively. The specimens were stressed in axial compression to failure. Displacement, elastic limit, ultimate load, and stiffness were recorded and calculated. RESULTS: There was no difference in mean cyclic displacement between the three groups (0.71 mm vs 0.89 mm vs 0.61 mm for Group A, B, C, respectively). Lateral plating demonstrated the greatest absolute and relative displacement at the elastic limit (5.3 mm ± 1.5 and 4.4 mm ± 1.3) without significance. The elastic limit or yield point was greatest for fibular allograft, Group C (1223 N ± 501 vs 1048 N ± 367 for Group B and 951 N ± 249 for Group A) without significance. CONCLUSIONS: Dual plating of proximal humerus fractures in a 90-90 configuration demonstrates similar biomechanical properties as endosteal fibular strut allograft. Both strategies demonstrate superior stiffness to isolated lateral locked plating.

The Effect of Buttress Plating on Biomechanical Stability of Coronal Shear Fractures of the Capitellum: A Cadaveric Study.

PURPOSE: The purpose of this study was to compare, using a cadaveric model, the biomechanical properties of headless compression screws (HCSs) and HCSs augmented with a buttress plate (BP) in capitellar fractures. METHODS: Twenty pairs of fresh-frozen humeri (mean age, 46.3 years; range, 33-58 years) were used. The soft tissue was removed, and a Dubberley type IA capitellar fracture was created. One specimen in each pair was randomly assigned to receive either two 2.5-mm HCSs (HCS group) or two 2.5-mm HCSs augmented with an anterior 2.4-mm BP (HCS + BP group). This resulted in a similar distribution of the left and right humeri between the groups. Cyclic loading was performed, and displacement of the capitellum at 50, 100, 250, 500, 1,000, and 2,000 cycles was assessed using a motion capture system. This was followed by load-to-failure testing, wherein the load at a displacement of 1 and 2 mm was recorded. Failure was defined as 2-mm displacement. RESULTS: During cyclic loading, there were no significant differences in the displacement between the HCS and HCS + BP groups at any of the assessed cycles. During load-to-failure testing, no significant strength differences were observed in the load at 1-mm displacement between the HCS (mean: 449.8 N, 95% CI: 283.6-616.0) and HCS + BP groups (mean: 606.2 N, 95% CI: 476.4-736.0). However, a significantly smaller load resulted in a 2-mm displacement of the fragment in the HCS group (mean: 668.8 N, 95% CI: 414.3-923.2) compared with the HCS + BP group (mean: 977.5 N, 95% CI: 794.1-1,161.0). CONCLUSIONS: Anterior, low-profile buttress plating in addition to HCSs results in a significantly higher load to failure compared with HCSs alone in a biomechanical Dubberley type IA capitellar fracture model. CLINICAL RELEVANCE: The addition of an anterior BP may be considered to improve initial stability in select cases such as osteoporotic patients or when the posterolateral column is frail.

Full thickness quadriceps tendon grafts with bone had similar material properties to bone-patellar tendon-bone and a four-strand semitendinosus grafts: a biomechanical study.

PURPOSE: Despite increasing interest in utilizing quadriceps tendon (QT) grafts in anterior cruciate ligament reconstruction (ACLR), data on the optimal quadriceps graft thickness are limited. The purpose of this study was to characterize the mechanical properties for the quadriceps tendon, comparing full-thickness (FT) QT grafts with and without bone to a partial-thickness (PT) QT graft, and comparing the three QT grafts to four-stranded semitendinosus (4-SST) and bone-patellar tendon-bone (BTB) grafts and one experimental graft, the two-stranded rectus femoris (RF). METHODS: Forty-eight (n = 48) young cadaveric grafts (mean age 32 ± 6 years) were utilized for testing with N = 8 specimens in each of the following groups; (1) FT QT with bone, (2) FT QT without bone, (3) PT QT without bone, (4) BTB, (5) RF, and (6) 4-SST. Each specimen was harvested and rigidly fixed in custom clamps to a dynamic tensile testing machine for biomechanical evaluation. Graft ultimate load and stiffness were recorded. Independent groups one-factor ANOVAs and Tukey's pairwise comparisons were performed for statistical analyses. RESULTS: FT QT with bone and 4-SST grafts demonstrated similar ultimate loads to BTB grafts (both n.s), whereas PT QT demonstrate statistically significantly lower ultimate loads to BTB grafts (n.s) and 4-SST grafts (n.s). Furthermore, no statistically significant differences were observed between the ultimate loads of FT QT vs. PT QT grafts without bone (n.s) or between FT QT with vs. without bone (n.s). FT QT grafts with bone did not demonstrate statistically significantly greater ultimate loads than PT QT grafts without bone (n.s). The RF graft demonstrated statistically significantly lower ultimate loads to BTB grafts (p < 0.005) and 4-SST grafts (p < 0.014). CONCLUSIONS: Full thickness QT grafts with bone had similar material properties to BTB and a 4-SST grafts, while Partial thickness QT graft without bone had significantly lower material properties than BTB and 4-SST, in a biomechanical setting.

Pullout Strength of All-Suture and Metallic Anchors in Repair of Lateral Collateral Ligament Injuries of the Elbow.

PURPOSE: To compare the biomechanical properties of metallic anchor (MA) and all-suture anchor (ASA) constructs in the anatomic reattachment of the lateral ulnar collateral ligament complex to its humeral insertion. METHODS: Twenty paired male human cadaveric elbows with a mean age of 46.3 years (range: 33-58 years) were used in this study. Each pair was randomly allocated across 2 groups of either MA or ASA. A single 3.5-mm MA or 2.6-mm ASA was then inserted flush into the lateral epicondyle. A dynamic tensile testing machine was used to perform cyclic loading followed by a load to failure test. During the cyclic loading phase, the anchors were sinusoidally tensioned from 10 N to 100 N for 1,000 cycles at a frequency of 0.5 Hz. In the load to failure test, the anchors were pulled at a rate of 3 mm/s. Load at 1-mm and 2-mm displacement, as well as load to ultimate failure were assessed. Clinical failure was defined as displacement of more than 2 mm. Normality of data was assessed with the Shapiro-Wilk test. Continuous data are presented as medians and compared with the Mann-Whitney U test and categorical data was compared with the χ2 test or Fisher exact test. RESULTS: Displacement was significantly greater for the ASA group during cyclic loading starting from the tenth cycle (P < .05). Displacement of more than 5 mm within the first 100 cycles was observed in 2 anchors in the ASA group. No difference was observed in loads required to displace 1 mm (MA: 146 N [6-169] vs ASA: 144 N [2-153]; P = .53) and 2 mm (MA: 171 N [13-202] vs ASA: 161 N [9-191]; P = .97), but there was a statistically significant difference between ultimate loads in favor of ASA in the load to failure test (MA: 297 N [84-343] vs 463 N [176-620]; P < .01). CONCLUSIONS: In the cyclic test, no difference in clinical failure defined as pull-out of more than 2 mm was observed between 3.5 mm MAs and 2.6 mm ASAs. In the ultimate load to failure analysis, no difference was observed between groups in force causing 1 and 2 mm of displacement, but there was a significant difference in favor of ASA in the pull to ultimate failure test. CLINICAL RELEVANCE: Potential benefits of all-suture anchors include preservation of bone stock, reduced radiographic artifacts, and easier revisions. Although their use has been investigated thoroughly in the shoulder, there remains a paucity of literature regarding displacement and pull-out strength in the elbow.

Does dual plating clavicle fractures increase the risk of refracture after hardware removal? A biomechanical investigation.

BACKGROUND: Dual orthogonal plating of midshaft clavicle fractures is increasingly used for osteosynthesis. The risk of refracture after hardware removal remains unknown. The purpose of this study was to compare the torsional and 3-point bending loads to failure of the clavicle following removal of single-plane, superior 3.5-mm plate fixation vs. dual orthogonal plating 2.7-mm constructs. METHODS: This study used 12 pairs of clavicles (N = 24) harvested from cadaveric specimens with a mean age at death of 56.5 years (range, 46-65 years). One clavicle from each pair was randomly assigned to either superior plating (SP, n = 12) or double plating (DP, n = 12). For SP, a superior 3.5-mm plate was used as a template to drill 3 bicortical 2.8-mm holes medial and lateral to the center of the clavicle. For DP, two 2.7-mm plates were used as a template to drill 4 bicortical 2.0-mm holes medial and lateral to the center of the clavicle. Clavicle pairs were randomly and evenly distributed to undergo either 3-point bending (n = 12) or posterior torsional loading (n = 12). Cyclic loading was performed, followed by load-to-failure testing. Stiffness, displacement at failure, load to failure, and failure mode were assessed and compared between SP and DP constructs. RESULTS: No significant differences between the SP and DP groups were observed for stiffness (768.2 ± 281.3 N/mm vs. 785.5 ± 315.0 N/mm, P = .872), displacement at failure (8.1 ± 2.8 mm vs. 5.4 ± 1.2 mm, P = .150), and ultimate load at failure (1831.0 ± 229.6 N vs. 1842.0 ± 662.4 N, P = .964) under the condition of 3-point bending. Similarly, no significant differences between the SP and DP groups were observed for torsional stiffness (1.3 ± 0.8 N · m/° vs. 1.1 ± 0.4 N · m/°, P = .844), rotation at failure (17.3° ± 4.4° vs. 14.4° ± 1.2°, P = .205), and ultimate torque at failure (14.8 ± 6.5 N · m vs. 14.7 ± 6.9 N · m, P = .103) under the condition of posterior torsional loading. The most common mode of failure for 3-point bending testing was an oblique fracture (7 of 12 clavicles, 58.3%), with no significant difference between groups (3 of 6 in SP group [50%] vs. 4 of 6 in DP group [66.7%], P > .999). The most common mode of failure with posterior torsional loading was a spiral fracture (10 of 12 clavicles, 83.3%), with no significant difference between groups (4 of 6 in SP group [66.7%] vs. 6 of 6 in DP group [100%], P = .455). CONCLUSION: Following clavicle plate removal of either DP or SP, there is no statistically significant difference in the amount of force, under the condition of 3-point bending or torsional loading, required to fracture the diaphyseal clavicle in vitro.

Biomechanical significance of the collateral ligaments in transolecranon fracture-dislocations.

BACKGROUND: It is widely accepted that transolecranon fracture-dislocations are not associated with collateral ligament disruption. The aim of the present study was to investigate the significance of the collateral ligaments in transolecranon fractures. METHODS: Twenty cadaveric elbows with a mean age of 46.3 years were used. All soft tissue was dissected to the level of the capsule, leaving the anterior band of the medial collateral ligament (MCL) and lateral collateral ligament (LCL) intact. A standardized, oblique osteotomy starting from the distal margin of the cartilage bare area of the ulna was made. The elbows were loaded with an inferiorly directed force of 5 and 10 N in the intact, MCL cut, LCL cut, and both ligaments cut states. All measurements were recorded on lateral calibrated radiographs. RESULTS: The mean inferior translation with intact ligaments (n = 20) when the humerus was loaded with 5 and 10 N was 1.52 mm (95% confidence interval [CI], 1.02-2.02) and 2.23 mm (95% CI, 1.61-2.85), respectively. When the LCL was cut first (n = 10), the inferior translation with 5 and 10 N load was 4.11 mm (95% CI, 0.95-7.26) and 4.82 mm (95% CI, 1.91-7.72), respectively. When the MCL was cut first (n = 10), the inferior translation when loaded with 5 and 10 N was 3.94 mm (95% CI, 0.796-7.08) and 5.68 mm (95% CI, 3.03-8.33), respectively. The inferior translation when loaded with 5 and 10 N and both ligaments cut was 15.65 mm (95% CI, 12.59-18.79) and 17.50 mm (95% CI, 14.86-20.13), respectively. There was a statistical difference between the intact and MCL cut first at 10 N and when both ligaments were cut at 5 and 10 N. CONCLUSIONS: The findings suggest that collateral ligament disruption is a prerequisite for a transolecranon fracture-dislocation. An inferior translation of more than 3 mm suggests that at least one of the collateral ligaments is disrupted, and more than 7.5 mm indicates that both collateral ligaments are disrupted.

The effect of glenosphere lateralization and inferiorization on deltoid force in reverse total shoulder arthroplasty.

BACKGROUND: A medialized center of rotation (COR) in reverse total shoulder arthroplasty (RTSA) comes with limitations such as scapular notching and reduced range of motion. To mitigate these effects, lateralization and inferiorization of the COR are performed, but may adversely affect deltoid muscle force. The study purposes were to measure the effect of RTSA with varying glenosphere configurations on (1) the COR and (2) deltoid force compared with intact shoulders and shoulders with massive posterosuperior rotator cuff tears (PS-RCT). We hypothesized that the highest deltoid forces would occur in shoulders with PS-RCT, and that RTSA would lead to a decrease in required forces that is further minimized with lateralization and inferiorization of the COR but still higher compared with native shoulders with an intact rotator cuff. METHODS: In this study, 8 cadaveric shoulders were dissected leaving only the rotator cuff muscles and capsule intact. A custom apparatus incorporating motion capture and a dynamic tensile testing machine to measure the changes in COR and deltoid forces while simultaneously recording glenohumeral abduction was designed. Five consecutive testing states were tested: (1) intact shoulder, (2) PS-RCT, (3) RTSA with standard glenosphere, (4) RTSA with 4 mm lateralized glenosphere, and (5) RTSA with 2.5 mm inferiorized glenosphere. Statistical Parametric Mapping was used to analyze the deltoid force as a function of the abduction angle. One-way repeated-measures within-specimens analysis of variance was conducted, followed by post hoc t-tests for pairwise comparisons between the states. RESULTS: All RTSA configurations shifted the COR medially and inferiorly with respect to native (standard: 4.2 ± 2.1 mm, 19.7 ± 3.6 mm; 4 mm lateralized: 3.9 ± 1.2 mm, 16.0 ± 1.8; 2.5 mm inferiorized: 6.9 ± 0.9 mm, 18.9 ± 1.7 mm). Analysis of variance showed a significant effect of specimen state on deltoid force across all abduction angles. Of the 10 paired t-test comparisons made between states, only 3 showed significant differences: (1) intact shoulders necessitated significantly lower deltoid force than specimens with PS-RCT below 42° abduction, (2) RTSAs with standard glenospheres required significantly lower deltoid force than RTSA with 4 mm lateralized glenospheres above 34° abduction, and (3) RTSAs with 2.5 mm inferiorized glenospheres had significantly lower deltoid force than RTSA with 4 mm of glenosphere lateralization at higher abduction angles. CONCLUSIONS: RTSA with a 2.5 mm inferiorized glenosphere and no additional lateralization resulted in less deltoid force to abduct the arm compared with 4 mm lateralized glenospheres. Therefore, when aiming to mitigate downsides of a medialized COR, an inferiorized glenosphere may be preferable in terms of its effect on deltoid force.

Biomechanical Comparison of Knotless All-Suture Anchors and Knotted All-Suture Anchors in Type II SLAP Lesions: A Cadaveric Study.

PURPOSE: To compare the biomechanical performance of knotless versus knotted all-suture anchors for the repair of type II SLAP lesions with a simulated peel-back mechanism. METHODS: Twenty paired cadaveric shoulders were used. A standardized type II SLAP repair was performed using knotless (group A) or knotted (group B) all-suture anchors. The long head of the biceps (LHB) tendon was loaded in a posterior direction to simulate the peel-back mechanism. Cyclic loading was performed followed by load-to-failure testing. Stiffness, load at 1 and 2 mm of displacement, load to repair failure, load to ultimate failure, and failure modes were assessed. RESULTS: The mean load to repair failure was similar in groups A (179.99 ± 58.42 N) and B (167.83 ± 44.27 N, P = .530). The mean load to ultimate failure was 230 ± 95.93 N in group A and 229.48 ± 78.45 N in group B and did not differ significantly (P = .958). Stiffness (P = .980), as well as load at 1 mm (P = .721) and 2 mm (P = .849) of displacement, did not differ significantly between groups. In 16 of the 20 specimens (7 in group A and 9 in group B), ultimate failure occurred at the proximal LHB tendon. Failed occurred through slippage of the labrum in 1 specimen in each group and through anchor pullout in 2 specimens in group A. CONCLUSIONS: Knotless and knotted all-suture anchors displayed high initial fixation strength with no significant differences between groups in type II SLAP lesions. Ultimate failure occurred predominantly as tears of the proximal LHB tendon. CLINICAL RELEVANCE: All-suture anchors have a smaller diameter than solid anchors, can be inserted through curved guides, preserve bone stock, and facilitate postoperative imaging. There is a paucity of literature investigating the biomechanical capacities of knotless versus knotted all-suture anchors in type II SLAP repair.