Attapulgite Nanorod-Incorporated Polyimide Membrane for Enhanced Gas Separation Performance.

Polyimide (PI) membrane is an ideal gas separation material due to its advantages of high designability, good mechanical properties and easy processing; however, it has equilibrium limitations in gas selectivity and permeability. Introducing nanoparticles into polymers is an effective method to improve the gas separation performance. In this work, nano-attapulgite (ATP) functionalized with KH-550 silane coupling agent was used to prepare polyimide/ATP composite membranes by in-situ polymerization. A series of characterization and performance tests were carried out on the membranes. The obtained results suggested a significant increase in gas permeability upon increasing the ATP content. When the content of ATP was 50%, the gas permeability of H2, He, N2, O2, CH4, and CO2 reached 11.82, 12.44, 0.13, 0.84, 0.10, and 4.64 barrer, which were 126.87%, 119.40%, 160.00%, 140.00%, 150.00% and 152.17% higher than that of pure polyimide, respectively. No significant change in gas selectivity was observed. The gas permeabilities of membranes at different pressures were also investigated. The inefficient polymer chain stacking and the additional void volume at the interface between the polymer and TiO2 clusters leaded to the increase of the free volume, thus improving the permeability of the polyimide membrane. As a promising separation material, the PI/ATP composite membrane can be widely used in gas separation industry.

Re-Stickable Yarn Supercapacitors with Vaper Phase Polymerized Multi-Layered Polypyrrole Electrodes for Smart Garments.

Yarn supercapacitors have attracted significant attention for wearable energy storage due to their ability to be directly integrated with garments. Conducting polymer polypyrrole (PPy) based yarn supercapacitors show limited cycling stability because of the huge volume changes during the charge-discharge processes. In addition, laundering may cause damage to such yarn supercapacitors. Here, the fabrication of PPy-based re-stickable yarn supercapacitors is reported with good cycling stability by employing vapor phase polymerization (VPP) and water-soluble polyethylene oxide (PEO) film as the adhesive layer. VPP duration and cycle are controlled to achieve multi-layered PPy electrodes. The assembled yarn supercapacitors show a good cycling stability with capacitance retention of 79.1% after 5000 charge-discharge cycles. The energy stored in the yarn supercapacitor is sufficient to power a photodetector. After gluing the yarn supercapacitors onto a PEO film, the devices can be stunk on and peeled off the garment to avoid the mechanical stresses during the washing process. Three yarn supercapacitors connected in parallel on PEO film show negative changes in electrochemical performance after 5 sticking-peeling cycles. This work provides a facile way to fabricate PPy-based re-stickable energy storage devices with high cycling stability for smart garments.

Assembly of MXene/PP Separator and Its Enhancement for Ni-Rich LiNi0.8Co0.1Mn0.1O2 Electrochemical Performance.

In this work, a few-layer MXene is prepared and sprinkled on a commercial polypropylene (PP) separator by a facile spraying method to enhance the electrochemistry of the Ni-rich LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode. Scanning electron microscope (SEM) and X-ray diffraction (XRD) are used to characterize the morphology and structure of MXene. Fourier transform infrared spectroscopy (FT-IR) and a contact angle tester are used to measure the bond structure and surface wettability PP and MXene/PP separator. The effect of the MXene/PP separator on the electrochemical performance of ternary NCM811 material is tested by an electrochemical workstation. The results show that the two-dimensional MXene material could improve the wettability of the separator to the electrolyte and greatly enhance the electrochemical properties of the NCM811 cathode. During 0.5 C current density cycling, the Li/NCM811 cell with MXene/PP separator remains at 166.2 mAh/g after the 100 cycles with ~90.7% retention. The Rct of MXene/PP cell is measured to be ~28.0 Ω. Combining all analyses results related to MXene/PP separator, the strategy by spraying the MXene on commercial PP is considered as a simple, convenient, and effective way to improve the electrochemical performance of the Ni-rich NCM811 cathode and it is expected to achieve large-scale in high-performance lithium-ion batteries in the near future.

High Performance Attapulgite/Polypyrrole Nanocomposite Reinforced Polystyrene (PS) Foam Based on Supercritical CO2 Foaming.

CO2 has been regarded as one of the most promising blowing agents for polystyrene (PS) foam due to its non-flammability, low price, nontoxicity, and eco-friendliness. However, the low solubility and fast diffusivity of CO2 in PS hinder its potential applications. In this study, an attapulgite (ATP)/polypyrrole (PPy) nanocomposite was developed using the in situ polymerization method to generate the hierarchical cell texture for the PS foam based on the supercritical CO2 foaming. The results demonstrated that the nanocomposite could act as an efficient CO2 capturer enabling the random release of it during the foaming process. In contrast to the pure PS foam, the ATP/PPy nanocomposite reinforced PS foam is endowed with high cell density (up to 1.9 × 106) and similar thermal conductivity as the neat PS foam, as well as high compression modulus. Therefore, the in situ polymerized ATP/PPy nanocomposite makes supercritical CO2 foaming desired candidate to replace the widely used fluorocarbons and chlorofluorocarbons as PS blowing agents.