Low-dose radiotherapy to the lungs using an interventional radiology C-arm fluoroscope: Monte Carlo treatment planning and dose measurements in a postmortem subject.

Objective.The goal of this study was to use Monte Carlo (MC) simulations and measurements to investigate the dosimetric suitability of an interventional radiology (IR) c-arm fluoroscope to deliver low-dose radiotherapy to the lungs.Approach.A previously-validated MC model of an IR fluoroscope was used to calculate the dose distributions in a COVID-19-infected patient, 20 non-infected patients of varying sizes, and a postmortem subject. Dose distributions for PA, AP/PA, 3-field and 4-field treatments irradiating 95% of the lungs to a 0.5 Gy dose were calculated. An algorithm was created to calculate skin entrance dose as a function of patient thickness for treatment planning purposes. Treatments were experimentally validated in a postmortem subject by using implanted dosimeters to capture organ doses.Main results.Mean doses to the left/right lungs for the COVID-19 CT data were 1.2/1.3 Gy, 0.8/0.9 Gy, 0.8/0.8 Gy and 0.6/0.6 Gy for the PA, AP/PA, 3-field, and 4-field configurations, respectively. Skin dose toxicity was the highest probability for the PA and lowest for the 4-field configuration. Dose to the heart slightly exceeded the ICRP tolerance; all other organ doses were below published tolerances. The AP/PA configuration provided the best fit for entrance skin dose as a function of patient thickness (R2 = 0.8). The average dose difference between simulation and measurement in the postmortem subject was 5%.Significance.An IR fluoroscope should be capable of delivering low-dose radiotherapy to the lungs with tolerable collateral dose to nearby organs.

Antisenescence effect of REAC biomodulation to counteract the evolution of myelodysplastic syndrome.

About 30 percent of patients diagnosed with myelodysplastic syndromes (MDS) progress to acute myeloid leukemia (AML). The senescence of bone marrow?derived mesenchymal stem cells (BMSCs) seems to be one of the determining factors in inducing this drift. Research is continuously looking for new methodologies and technologies that can use bioelectric signals to act on senescence and cell differentiation towards the phenotype of interest. The Radio Electric Asymmetric Conveyer (REAC) technology, aimed at reorganizing the endogenous bioelectric activity, has already shown to be able to determine direct cell reprogramming effects and counteract the senescence mechanisms in stem cells. Aim of the present study was to prove if the anti-senescence results previously obtained in different kind of stem cells with the REAC Tissue optimization - regenerative (TO-RGN) treatment, could also be observed in BMSCs, evaluating cell viability, telomerase activity, p19ARF, P21, P53, and hTERT gene expression. The results show that the REAC TO-RGN treatment may be a useful tool to counteract the BMSCs senescence which can be the basis of AML drift. Nevertheless, further clinical studies on humans are needed to confirm this hypothesis.

Monte Carlo simulations and phantom validation of low-dose radiotherapy to the lungs using an interventional radiology C-arm fluoroscope.

PURPOSE: To use MC simulations and phantom measurements to investigate the dosimetry of a kilovoltage x-ray beam from an IR fluoroscope to deliver low-dose (0.3-1.0 Gy) radiotherapy to the lungs. MATERIALS AND METHODS: PENELOPE was used to model a 125 kV, 5.94 mm Al HVL x-ray beam produced by a fluoroscope. The model was validated through depth-dose, in-plane/cross-plane profiles and absorbed dose at 2.5-, 5.1-, 10.2- and 15.2-cm depths against the measured beam in an acrylic phantom. CT images of an anthropomorphic phantom thorax/lungs were used to simulate 0.5 Gy dose distributions for PA, AP/PA, 3-field and 4-field treatments. DVHs were generated to assess the dose to the lungs and nearby organs. Gafchromic film was used to measure doses in the phantom exposed to PA and 4-field treatments, and compared to the MC simulations. RESULTS: Depth-dose and profile results were within 3.2% and 7.8% of the MC data uncertainty, respectively, while dose gamma analysis ranged from 0.7 to 1.0. Mean dose to the lungs were 1.1-, 0.8-, 0.9-, and 0.8- Gy for the PA, AP/PA, 3-field, and 4-field after isodose normalization to cover âˆ¼ 95% of each lung volume. Skin dose toxicity was highest for the PA and lowest for the 4-field, and both arrangements successfully delivered the treatment on the phantom. However, the dose distribution for the PA was highly non-uniform and produced skin doses up to 4 Gy. The dose distribution for the 4-field produced a uniform 0.6 Gy dose throughout the lungs, with a maximum dose of 0.73 Gy. The average percent difference between experimental and Monte Carlo values were -0.1% (range -3% to +4%) for the PA treatment and 0.3% (range -10.3% to +15.2%) for the 4-field treatment. CONCLUSION: A 125 kV x-ray beam from an IR fluoroscope delivered through two or more fields can deliver an effective low-dose radiotherapy treatment to the lungs. The 4-field arrangement not only provides an effective treatment, but also significant dose sparing to healthy organs, including skin, compared to the PA treatment. Use of fluoroscopy appears to be a viable alternative to megavoltage radiation therapy equipment for delivering low-dose radiotherapy to the lungs.

Proteomic analysis of plasma proteins after low-level laser therapy in rats.

The laser radiation absorbed by cells induces production of reactive oxygen species (ROS), followed by the development of oxidative stress. Proteins are major targets for ROS due to their abundance in biological systems. The aim of the present pilot study was to examine the effects of transcutaneous laser blood irradiation (TLBI), i.e., low-level laser therapy (LLLT) at 830 nm on plasma proteome in Wistar rats. Rats were irradiated in the heart area (i.e. coronary arteries) daily (i.e., for 9-day period), by commercially available GaAsAl diode laser (Maestro/CCM, Medicom Prague, Czech Republic, lambda=830 nm, power density 450mW/cm(2), daily dose 60,3 J/ cm(2), irradiation time 134 sec). The comparison of blood plasma proteome from irradiated and non-irradiated rats was performed utilizing 2D electrophoresis followed by MALDI TOF/TOF mass spectrometry. LLLT led to a quantitative change in the acute phase proteins with antioxidant protection i.e., haptoglobin (log(2) fold change (FC)=3.5), hemopexin (log(2) FC=0.5), fibrinogen gamma (log2 FC=1.4), alpha-1-antitrypsin (log(2) FC=-2.2), fetuin A (log2 FC=-0.6) and fetuin B (log2 FC=-2.3). In comparison to conventional biochemical methods, the changes in protein levels in blood plasma induced by LLLT offer a deeper insight into the oxidative stress response.

PVA and PCL nanofibers are suitable for tissue covering and regeneration.

The aim of the study was to evaluate the safety and efficacy of a new therapeutic approach to skin defects resulting from split thickness grafting. Within the study, nanofiber-based dressings fabricated using polyvinyl alcohol (PVA) and poly-ε-caprolactone (PCL) were used, with different mass density. The study was performed in 1 female minipig. Nine defects (approx. 4x4 cm) were made in the superficial skin layer. The tested materials were applied to the squared skin defect and covered by a Jelonet paraffin gauze, sutured in the corners of the defects. The animal was monitored daily during the healing process (21 days). On day 5, 12, and 27, the healing of the wound was evaluated, and a biopsy was performed for further histologic testing. At the end of the study (on day 27 after the procedure), the animal was euthanized, and a standard pathologic evaluation was performed. We can conclude that the nanofiber scaffold which was well tolerated, could be used as a smart skin cover which could be functionalized with another bioactive substances directly on the surgeon table, among potential bioactive substances belong platelet derivatives, antibiotics, etc.

[Use of the Peptigel with Nanofibres in the Bone Defects Healing]. / Vyuzití peptigelu s nanovlákny k lécbe defektu kostní tkáne.

INTRODUCTION Traumatic bone injuries or pathological processes may sometimes result in very extensive bone defects. Currently, the standard procedure applied in clinical humane as well as veterinary medicine to fill a bone defect is the autogenous bone graft which, however, necessitates a more invasive procedure for the patient and in the cases of extensive defects it fails to provide adequate amount of graft. Synthetic bone replacements can be used with no further burden for the patient and can simultaneously be used as the carriers for bioactive molecules or therapeutic drugs. For clinical use, an easy and simple application is one of the requirements that have to be taken into consideration. These requirements are best satisfied by preparations in the form of gel, which may be injected into the defects of various shapes even through minimal surgical approach. MATERIAL AND METHODS Synthetic transparent PGD-AlphaProA hydro-peptide-gel was used as a basis to develop a composite hydrogel scaffold. This gel was enriched by cryogenically ground poly- -caprolactone nanofibers (PCL) in a ratio of 1 ml of gel to 16 µg of nanofibres. In experimental animals (laboratory rat Wistar, n=20), a single regular circular defect of 1.5 mm in diameter was drilled by a low speed drill machine across the whole width of distal femur diaphysis, identically in both the hind legs. In the right hindleg, this defect was filled by injection of 0.05 ml of the composite peptide gel with nanofibers (experimental defect). In the contralateral limb a similar defect was left untreated, without filling (control defect), for spontaneous healing. The group of experimental animals was subsequently divided into four sub-groups (A, B, C, D) for the purpose of further follow-up. One week after the surgical implantation, in the first group of experimental animals (Group A; n = 5) lege artis euthanasia was performed, a radiological examination of both the hind legs was carried out and a sample of the bone from both the control and experimental defect was collected for histologic examination. The other groups of experimental animals were evaluated similarly at 2, 4 and 6 weeks after the surgical procedure (Group B, C, D; n = 5). These groups of experimental animals were assessed using various histological techniques by two independent pathologists. RESULTS A difference between the control and the experimental bone defect was observed only at the healing stage at two weeks after the implantation, when a tendency for greater formation of new bone trabeculas was seen in the defect treated with the composite hydro-peptide-gel with PCL nanofibers. The results show a slightly higher angiogenesis and cellularity at the bone defect site with an increase of newly formed bone tissue and faster colonisation of lamellar bone structures by bone marrow cells at early stages of the healing process (1-2 weeks old defect). In the experimental and control groups, at the later stage of healing (4-6 weeks old defect), the process of healing and bone modelling at the defect site shows no detectable morphological differences. CONCLUSIONS The experimental use of hydro-peptide-gel with PCL nanofibers in vivo in laboratory rats shows very good applicability into the defect site and, compared to the untreated defect within two weeks after the implantation, accelerates the bone healing. This fact could be an advantage especially at the early stage of healing, and thus accelerate the healing of more extensive defects. Key words: peptide gel, polycaprolactone, PCL, replacement, bone, healing, scaffold, nanofibers, biomaterial.

[Canine Elbow Humeroulnar Incongruity Measurements Using Computed Tomography]. / Merení humeroulnární inkongruity loketního kloubu u psu pomocí výpocetní tomografie.

PURPOSE OF THE STUDY The purpose of the study is to compare the repeatability and reproducibility of quantitative and subjective evaluation of elbow humeroulnar incongruity (HUI) using computed tomography (CT) on an in vivo canine model. MATERIAL AND METHODS HUI was evaluated on canine (n = 50) elbow joints (n = 100). The computed tomography of elbow joints was performed under intravenous sedation. Multiplanar reconstructions (MPR) were produced. HUI was evaluated on sagittal MPR images subjectively and by measuring the subluxation index (SI). The SI was defined by measuring the distance between the centres of two circles, the shape of which corresponded the most with the shape of the trochlear notch of the ulna at sagittal crest and the shape of humeral trochlea. This distance was divided by the radius of the circle (r) defining the humeral trochlea. HUI was subjectively evaluated based on the width of the joint space at the greatest caudal convexity of the trochlear notch of the ulna. Three categories of HUI were established: 0 (congruent), 1 (moderately incongruent), 2 (strongly incongruent). Measurement and evaluation of HUI was conducted by two evaluators twice at a one-month interval between the first and second measurement. The statistical analysis was carried out using the repeated measures ANOVA and the Cohen s kappa coefficient. RESULTS The mean SI was 11.14 (SD 8.703). The SI values measured by two evaluators were statistically significantly different (p < 0.05). Contrarily, there was no statistically significant difference between the two measurements of the same evaluator (p > 0.05). The subjective evaluation of HUI done by two evaluators showed a mean to substantial agreement (Kappa = 0.53-0.79). There was a substantial to almost perfect agreement between the results of two evaluations carried out by a single evaluator (Kappa = 0.79-0.83). DISCUSSION The radiographic detection of moderate incongruity is unreliable, especially on account of wrongly positioned elbow joint, superposition of bone structures and due to the evaluation of three-dimensional bone structure through a two-dimensional image. Evaluation of humeroulnar congruity by computed tomography (CT) enables to assess the congruity of joints without the superposition of neighbouring bone structures. The quantification of humeroulnar incongruity using the SI does not show a higher degree of agreement between two evaluators as against the subjective evaluation of HUI. On the contrary, the agreement between two measurements of a single evaluator was high in both the cases. CONCLUSIONS Dog is a suitable model animal for evaluation of HUI of elbow joints due to frequent incidence of elbow dysplasia associated with HUI. The quantification of HUI at the expense of subjective evaluation of HUI is often overrated in radiological studies. Key words: dog, elbow, humeroulnar incongruity.

[Comparison between the Range of Movement Canine Real Cervical Spine and Numerical Simulation - Computer Model Validation]. / Porovnání rozsahu pohybu reálné krcní pátere psa s pocítacovou simulací ­ validace pocítacového modelu.

PURPOSE OF THE STUDY In developing new or modifying the existing surgical treatment methods of spine conditions an integral part of ex vivo experiments is the assessment of mechanical, kinematic and dynamic properties of created constructions. The aim of the study is to create an appropriately validated numerical model of canine cervical spine in order to obtain a tool for basic research to be applied in cervical spine surgeries. For this purpose, canine is a suitable model due to the occurrence of similar cervical spine conditions in some breeds of dogs and in humans. The obtained model can also be used in research and in clinical veterinary practice. MATERIAL AND METHODS In order to create a 3D spine model, the LightSpeed 16 (GE, Milwaukee, USA) multidetector computed tomography was used to scan the cervical spine of Doberman Pinscher. The data were transmitted to Mimics 12 software (Materialise HQ, Belgium), in which the individual vertebrae were segmented on CT scans by thresholding. The vertebral geometry was exported to Rhinoceros software (McNeel North America, USA) for modelling, and subsequently the specialised software Abaqus (Dassault Systemes, France) was used to analyse the response of the physiological spine model to external load by the finite element method (FEM). All the FEM based numerical simulations were considered as nonlinear contact statistic tasks. In FEM analyses, angles between individual spinal segments were monitored in dependence on ventroflexion/ /dorziflexion. The data were validated using the latero-lateral radiographs of cervical spine of large breed dogs with no evident clinical signs of cervical spine conditions. The radiographs within the cervical spine range of motion were taken at three different positions: in neutral position, in maximal ventroflexion and in maximal dorziflexion. On X-rays, vertebral inclination angles in monitored spine positions were measured and compared with the results obtain0ed from FEM analyses of the numerical model. RESULTS It is obvious from the results that the physiological spine model tested by the finite element method shows a very similar mechanical behaviour as the physiological canine spine. The biggest difference identified between the resulting values was reported in C6-C7 segment in dorsiflexion (Δφ = 5.95%), or in C4-C5 segment in ventroflexion (Δφ = -3.09%). CONCLUSIONS The comparisons between the mobility of cervical spine in ventroflexion/dorsiflexion on radiographs of the real models and the simulated numerical model by finite element method showed a high degree of results conformity with a minimal difference. Therefore, for future experiments the validated numerical model can be used as a tool of basic research on condition that the results of analyses carried out by finite element method will be affected only by an insignificant error. The computer model, on the other hand, is merely a simplified system and in comparison with the real situation cannot fully evaluate the dynamics of the action of forces in time, their variability, and also the individual effects of supportive skeletal tissues. Based on what has been said above, it is obvious that there is a need to exercise restraint in interpreting the obtained results. Key words: cervical spine, kinematics, numerical modelling, finite element method, canine.

[Intra-articular reinforcement of a partially torn anterior cruciate ligament (ACL) using newly developed UHMWPE biomaterial in combination with Hexalon ACL/PCL screws: ex-vivo mechanical testing of an animal knee model]. / Intraartikulární augmentace parciální ruptury predního zkrízeného vazu (ACL) nove vyvinutým UHMWPE biomateriálem v kombinaci s Hexalon ACL/PCL srouby: ex vivo mechanické testování animálního modelu kolenního kloubu.

PURPOSE OF THE STUDY Recent trends in the experimental surgical management of a partial anterior cruciate ligament (ACL) rupture in animals show repair of an ACL lesion using novel biomaterials both for biomechanical reinforcement of a partially unstable knee and as suitable scaffolds for bone marrow stem cell therapy in a partial ACL tear. The study deals with mechanical testing of the newly developed ultra-high-molecular-weight polyethylene (UHMWPE) biomaterial anchored to bone with Hexalon biodegradable ACL/PCL screws, as a new possibility of intra-articular reinforcement of a partial ACL tear. MATERIAL AND METHODS Two groups of ex vivo pig knee models were prepared and tested as follows: the model of an ACL tear stabilised with UHMWPE biomaterial using a Hexalon ACL/PCL screw (group 1; n = 10) and the model of an ACL tear stabilised with the traditional, and in veterinary medicine used, extracapsular technique involving a monofilament nylon fibre, a clamp and a Securos bone anchor (group 2; n = 11). The models were loaded at a standing angle of 100° and the maximum load (N) and shift (mm) values were recorded. RESULTS In group 1 the average maximal peak force was 167.6 ± 21.7 N and the shift was on average 19.0 ± 4.0 mm. In all 10 specimens, the maximum load made the UHMWPE implant break close to its fixation to the femur but the construct/fixation never failed at the site where the material was anchored to the bone. In group 2, the average maximal peak force was 207.3 ± 49.2 N and the shift was on average 24.1 ± 9.5 mm. The Securos stabilisation failed by pullout of the anchor from the femoral bone in nine out of 11 cases; the monofilament fibre ruptured in two cases. CONCLUSIONS It can be concluded that a UHMWPE substitute used in ex-vivo pig knee models has mechanical properties comparable with clinically used extracapsular Securos stabilisation and, because of its potential to carry stem cells and bioactive substances, it can meet the requirements for an implant appropriate to the unique technique of protecting a partial ACL tear. In addition, it has no critical point of ACL substitute failure at the site of its anchoring to the bone (compared to the previously used PET/PCL substitute). Key words: knee stabilisation, stifle surgery, ultra-high-molecular-weight polyethylene, UHMWPE, nylon monofilament thread, biodegradable screw, bone anchor.

Optimized conditions for mesenchymal stem cells to differentiate into osteoblasts on a collagen/hydroxyapatite matrix.

Collagen/hydroxyapatite (HA) composite scaffolds are known to be suitable scaffolds for seeding with mesenchymal stem cells (MSCs) differentiated into osteoblasts and for the in vitro production of artificial bones. However, the optimal collagen/HA ratio remains unclear. Our study confirmed that a higher collagen content increased scaffold stiffness but that a greater stiffness was not sufficient for bone tissue formation, a complex process evidently also dependent on scaffold porosity. We found that the scaffold pore diameter was dependent on the concentration of collagen and HA and that it could play a key role in cell seeding. In conclusion, the optimal scaffold for new bone formation and cell proliferation was found to be a composite scaffold formed from 50 wt % HA in 0.5 wt % collagen I solution.

[Treatment of a bone bridge by transplantation of mesenchymal stem cells and chondrocytes in a composite scaffold in pigs: experimental study]. / Lécba kostního mustku transplantací mezenchymových kmenových bunek a chondrocytu v kompozitním nosici u prasat - experimentální studie.

PURPOSE OF THE STUDY: The presented experimental study describes the results of using a combination of allogeneic mesenchymal cells (MSCs) with chondrocytes (CHCs) and a novel scaffold based on type I collagen and chitosan fibres. This biocomposite was transplanted into a defect produced by excision of a bone bridge to induce new cartilaginous tissue formation. The left femur was treated by transplantation into a defect of distal epiphysis; the right femur with implantation of the scaffold only served as control. A better therapeutic result was therefore expected in the left femur - the reduction of growth and angular deformities, and the histological finding of a tissue similar to the cartilage excised from the left femur.. MATERIAL AND METHODS: The miniature pig was selected as an experimental model and 10 pigs were used. Mesenchymal stem cells derived from femoral bone marrow and chondrocytes derived from a sample harvested from the non-weight-bearing articular surface of the distal end of the femur were cultured in medium. The novel scaffold was based on collagen containing chitosan nanofibres. To make manipulation during implantation easier, the cilindrical scaffolds after lyophilisation were again placed in 96-well plates for seeding. The scaffolds before implantation were seeded with 2x106 allogeneic MSCs and 1x106 allogeneic CHCs. The outcomes of treatment were assessed by measuring the length of bone and the degree of distal femoral valgus deformity, and by the histological findings obtained (properties and maturity of the newly-formed tissue, detection of type II collagen, PAS reaction). RESULTS: The right and left legs were examined for longitudinal bone growth and the valgus angle and compared. The treated left leg showed a higher average value for longitudinal growth than the untreated right leg (p = 0.004). The average degree of angular deformity was lower in the left leg than in the right leg (p = 0.008). The microscopic findings showed that a tissue similar to hyaline cartilage was more frequently present in the femoral bone defect of the left leg, as compared with that of the right leg. Type II collagen was detected more frequently and at higher amounts on the left than the right side (p = 0.033). The PAS reaction was positive in all left limbs, with a high degree of positivity in 80 % of them, while this was not achieved in any of the right limbs (p = 0.001). DISCUSSION: The use of stem cells in the indication reported here has only been the matter of time since the information on encouraging results in neurology and cardiology was published. First studies with positive results have soon been reported. The initial hydrogel scaffolds were based on tissue adhesives. However, they were not stable enough and were difficult to handle during surgery. In further studies, therefore, the use was made of a three-dimensional scaffold with a self-supporting structure of collagen fibres. This structure also facilitated its hydrodynamic seeding with MSCs and CHCs, which is an effective and sparing procedure for the transplanted cells. Studies concerned with MSCs and/or CHCs transplantation for re - pair of a physeal defect following bone bridge excision, i.e. for bone bridge treatment, in a broader experimental design, however, are still missing. CONCLUSION: Transplantation of a composite scaffold seeded with mesenchymal stem cells and chondrocytes into a physeal defect following bone bridge excision prevented growth disturbance and angular deformity development in the distal femoral epi - physis. In comparison with the control group, it resulted in a more frequent production of a tissue similar to hyaline cartilage, with a cell formation reminiscent of a typical columnar arrangement of the growth plate. Key words: mesenchymal stem cells, growth plate, bone bridge, scaffold.

Quality of newly formed cartilaginous tissue in defects of articular surface after transplantation of mesenchymal stem cells in a composite scaffold based on collagen I with chitosan micro- and nanofibres.

The aim of this study was to evaluate macroscopically, histologically and immunohistochemically the quality of newly formed tissue in iatrogenic defects of articular cartilage of the femur condyle in miniature pigs treated with the clinically used method of microfractures in comparison with the transplantation of a combination of a composite scaffold with allogeneic mesenchymal stem cells (MSCs) or the composite scaffold alone. The newly formed cartilaginous tissue filling the defects of articular cartilage after transplantation of the scaffold with MSCs (Group A) had in 60 % of cases a macroscopically smooth surface. In all lesions after the transplantation of the scaffold alone (Group B) or after the method of microfractures (Group C), erosions/fissures or osteophytes were found on the surface. The results of histological and immunohistochemical examination using the modified scoring system according to O'Driscoll were as follows: 14.7+/-3.82 points after transplantations of the scaffold with MSCs (Group A); 5.3+/-2.88 points after transplantations of the scaffold alone (Group B); and 5.2+/-0.64 points after treatment with microfractures (Group C). The O'Driscoll score in animals of Group A was significantly higher than in animals of Group B or Group C (p<0.0005 both). No significant difference was found in the O'Driscoll score between Groups B and C. The treatment of iatrogenic lesions of the articular cartilage surface on the condyles of femur in miniature pigs using transplantation of MSCs in the composite scaffold led to the filling of defects by a tissue of the appearance of hyaline cartilage. Lesions treated by implantation of the scaffold alone or by the method of microfractures were filled with fibrous cartilage with worse macroscopic, histological and immunohistochemical indicators.

Use of allogenic stem cells for the prevention of bone bridge formation in miniature pigs.

This study appears from an experiment previously carried out in New Zealand white rabbits. Allogenic mesenchymal stem cells (MSCs) were transplanted into an iatrogenically-created defect in the lateral section of the distal physis of the left femur in 10 miniature pigs. The right femur with the same defect served as a control. To transfer MSCs, a freshly prepared porous scaffold was used, based on collagen and chitosan, constituting a compact tube into which MSCs were implanted. The pigs were euthanized four months after the transplantation. On average, the left femur with transplanted MSCs grew more in length (0.56+/-0.14 cm) compared with right femurs with physeal defect without transplanted MSCs (0.14+/-0.3 cm). The average angular (valgus) deformity of the left femur had an angle point of 0.78 degrees , following measurement and X-ray examination, whereas in the right femur without transplantation it was 3.7 degrees. The initial results indicate that preventive transplantation of MSCs into a physeal defect may prevent valgus deformity formation and probably also reduce disorders of the longitudinal bone growth. This part of our experiment is significant in the effort to advance MSCs application in human medicine by using pig as a model, which is the next step after experimenting on rabbits.

[New options for management of posttraumatic articular cartilage defects]. / Nové moznosti v lécbe poúrazových defektu kloubní chrupavky.

Articular cartilage trauma, in particular due to its poor healing potential remains a complicated problem in both the adult and paediatric traumatology and orthopedics. In older patients, total endoprosthesis of the joint is a method of choice, however, in younger patients, the situation remains more complicated. In case of osteochondral lesions (arthrosis, chondral fractures. osteochoodrosis dissecns) the ideal management should result in complete recovery of the hyaline cartilage on the traumatized joint surface. Contemporary medicine uses some therapeutic procedures resulting in partial recovery of the articular cartilage structure at the lesion site and several techniques of excisionining the articular surface's injured part and of transplantations of biological grafts. Regarding the above first approach, abrasive methods (micro fractures, small drill holes), which are expected to result in recovery of the articular cartilage through progenitor cells that migrate from the bone marrow to the defect site following subchondral fracturing. In case the injury is managed early, the osteochondral fragment may be fixed and the articular congruence be recovered. Mosaicoplasty using osteochondral auto grafts or other autologous grafts, or more recently using transplantations of autologous chond rocytes, which seem to have a major potential in the hyaline cartilage healing process. However, methodology of the transplant retention at the defect site remains a problem. Furthermore, the use of mesenchymal stem cells, so far in the experimental phase, appears prospective. Pivotal articular cartilage treatment research activities have progressed to a level of searching for a suitable scaffold of perfect qualities. This is the task for cooperation with bioengineering. requiring provision of the most exact differentiation protocol for hyline cartilage producing mesenchymal stem cells (MSCs).

Use of 3D geometry modeling of osteochondrosis-like iatrogenic lesions as a template for press-and-fit scaffold seeded with mesenchymal stem cells.

Computed tomography (CT) is an effective diagnostic modality for three-dimensional imaging of bone structures, including the geometry of their defects. The aim of the study was to create and optimize 3D geometrical and real plastic models of the distal femoral component of the knee with joint surface defects. Input data included CT images of stifle joints in twenty miniature pigs with iatrogenic osteochondrosis-like lesions in medial femoral condyle of the left knee. The animals were examined eight and sixteen weeks after surgery. Philips MX 8000 MX and View workstation were used for scanning parallel plane cross section slices and Cartesian discrete volume creation. On the average, 100 slices were performed in each stifle joint. Slice matrices size was 512 x 512 with slice thickness of 1 mm. Pixel (voxel) size in the slice plane was 0.5 mm (with average accuracy of +/-0.5 mm and typical volume size 512 x 512 x 100 voxels). Three-dimensional processing of CT data and 3D geometrical modelling, using interactive computer graphic system MediTools formerly developed here, consisted of tissue segmentation (raster based method combination and 5 % of manual correction), vectorization by the marching-cubes method, smoothing and decimation. Stifle- joint CT images of three individuals of different body size (small, medium and large) were selected to make the real plastic models of their distal femurs from plaster composite using rapid prototyping technology of Zcorporation. Accuracy of the modeling was +/- 0.5 mm. The real plastic models of distal femurs can be used as a template for developing custom made press and fit scaffold implants seeded with mesenchymal stem cells that might be subsequently implanted into iatrogenic joint surface defects for articular cartilage-repair enhancement.

Mechanical response of porous scaffolds for cartilage engineering.

Mechanical properties of scaffolds seeded with mesenchymal stem cells used for cartilage repair seem to be one of the critical factors in possible joint resurfacing. In this paper, the effect of adding hyaluronic acid, hydroxyapatite nanoparticles or chitosan nanofibers into the cross-linked collagen I on the mechanical response of the lyophilized porous scaffold has been investigated in the dry state at 37 oC under tensile loading. Statistical significance of the results was evaluated using ANOVA analysis. The results showed that the addition of hyaluronic acid significantly (p<<0.05) reduced the tensile elastic modulus and enhanced the strength and deformation to failure of the modified cross-linked collagen I under the used test conditions. On the other hand, addition of hydroxyapatite nanoparticles and chitosan nanofibers, respectively, increased the elastic modulus of the modified collagen ten-fold and four-fold, respectively. Hydroxyapatite caused significant reduction in the ultimate deformation at break while chitosan nanofibers enhanced the ultimate deformation under tensile loading substantially (p<<0.05). The ultimate tensile deformation was significantly (p<<0.05) increased by addition of the chitosan nanofibers. The enhanced elastic modulus of the scaffold was translated into enhanced resistance of the porous scaffolds against mechanical load compared to scaffolds based on cross-linked neat collagen or collagen with hyaluronic acid with similar porosity. It can be concluded that enhancing the rigidity of the compact scaffold material by adding rigid chitosan nanofibers can improve the resistance of the porous scaffolds against compressive loading, which can provide more structural protection to the seeded mesenchymal stem cells when the construct is implanted into a lesion. Moreover, scaffolds with chitosan nanofibers seemed to enhance cell growth compared to the neat collagen I when tested in vitro as well as the scaffold stability, extending its resorption to more than 10 weeks.

Subtotal intracapsular prostatectomy as a useful treatment for advanced-stage prostatic malignancies.

OBJECTIVES: Palliative surgery for advanced-stage prostatic cancers was tested with regard to survival rate and complications in a prospective randomised clinical study of dogs. Currently, therapeutic approaches have a grave long-term prognosis in clinically significant prostatic cancer. METHODS: Of 167 dogs with prostatic disorders, 24 were diagnosed with prostatic cancer. Eleven dogs underwent subtotal intracapsular prostatectomy, while in 10 dogs total prostatectomy was performed. The remaining three dogs were euthanased at their owner's request. Dogs treated by subtotal intracapsular prostatectomy and those treated by total prostatectomy were followed until their death. RESULTS: It was found that dogs treated by subtotal intracapsular prostatectomy survived 5.63 times longer (mean [sd] 112.0 [63.03] days) than those treated by total prostatectomy (19.9 [10.67] days) (P<0.01). Moreover, a significant decrease in postoperative complications after subtotal intracapsular prostatectomy was recorded, especially with regard to urinary incontinence. CLINICAL SIGNIFICANCE: It was concluded that, in the authors' facility, treatment of prostatic cancer by subtotal intracapsular prostatectomy was superior to that by total prostatectomy, with respect to both postoperative survival and serious complications.

[Neurosurgical therapy of intervertebral disk disease in dogs]. / Neurochirurgická lécba onemocnení meziobratlových plotének u psu.

Intervertebral disc degeneration and protrusion or extrusion of disc material into the vertebral canal cause focal compressive myelopathy and radiculopathy, the most common neurological syndrome in dogs. Clinical findings are variable depending on duration and location of the lesion, volume of the mass and dynamic considerations (peracute massive extrusion, chronic partial extrusion, chronic progressive extrusion). Aim of this article is to provide compendium of at-the-present-time recommended methods of surgical treatment of intervertebral disc disease in the dog. In the case of compression of spinal cord is performed decompressive surgery (ventral cervical decompression, hemilaminectomy, minihemilaminectomy, dorsal laminectomy and foramenotomy). Fenestration is the only method of prophylaxis.

[Results of surgical treatment in disorders of the thoracolumbar disks in dogs]. / Výsledky chirurgické lécby onemocnení torakolumbálních disku u psu.

The clinical records of 90 dogs with thoracolumbar disc disease treated by fenestration or decompressive surgery on Surgical Department of the University of Veterinary and Pharmaceutical Sciences in Brno between September 1992 and March 1994 were reviewed. The breed, age and sex predisposition, rate of disc protrusion or extrusion and number of multiple disc extrusions were recorded. The frequency of disc protrusion/extrusion at each intervertebral space in thoracolumbar region of spine was also observed. Dogs were grouped by clinical signs of disease in four groups. Recovery rates depending on the pre-operative neurological grade of spinal injury and duration of clinical signs were compared. Patients were observed at least 6 months after surgery and the results of therapy were classified as good (complete recovery of motor and urinary function), fair (some remaining dysfunction, either motor or urinary, but animal retained independent function and usefulness) and poor (not enough improvement to be returned to the owner as an independent animal). Eight breeds and mixed-breed dogs were represented in the 90 cases of thoracolumbar disc disease. Shorthaired Dachshunds predominated (58.9%). The age range of dogs was 3-12 years; 52% were males and 48% females. Incidence of disc protrusion was 13.3% and disc extrusion 86.6% of the cases, with the frequency 3.3% of multiple disc extrusions. The most common site of lesion was the T12-T13 interspace. Twelve dogs in group II were treated by fenestration with good results of therapy in all cases. There was no recurrence of clinical signs during period of observation.(ABSTRACT TRUNCATED AT 250 WORDS)