A quantitative analysis of tension band plating of the femur diaphysis.

OBJECTIVES: To measure quantitatively the strains in the concave and convex sides of a femur to substantiate the Arbeitsgemeinschaft für Osteosynthesefragen (AO) tension band principle. METHODS: Eight cadaveric fresh-frozen femurs were cleaned of soft tissue and prepared for mounting the strain gages (Vishay, Raleigh, NC). The student strain gages were mounted at the anterior, lateral and medial surfaces of a femur. They were loaded at 100, 250, 500, 1,000 and 1,500 N axial forces in a mechanical testing machine (Instron Model 4202, Norwood, MA) and the micro strains were measured for intact and after fixation of a simulated fracture by an eight hole broad 4.5 mm stainless steel compression plate (Synthes LCP). In order to simulate the fracture conditions, where all eight screw holes might not be filled, three different arrangements were tested: 8 screws, 4 screws and 2 screws. The microstrains under different loads were analyzed by Analysis of Variance (ANOVA) with Holm-Sidak multiple comparison method. RESULTS: At the same gage location micro strains were not significantly different between the intact, and the femur fixated by 8, 4 and 2 screws. For intact bones at 1,500 N the strain ratio between the tension to compression sides was -0.21 proximally and -0.04 distally. The comparison of these strain ratios at different loads did not show any significant differences at p = 0.05 and power of 0.8. CONCLUSIONS: The data showed a trend validating the tension band principle as tensile strains lowered and compressive strains increased after placement of the plate.

Changes in load distribution in the knee after opening-wedge or closing-wedge high tibial osteotomy.

The treatment of unicompartmental osteoarthritis of the knee by high tibial osteotomy has been carried out by closing-wedge osteotomy. The advantages for opening-wedge osteotomy are ease of procedure and improved correction with comparable short-term to midterm results. It is not known how the opening-wedge high tibial osteotomy procedure alters the load distribution between the medial and lateral compartments of the knee. The current biomechanical study investigated opening-wedge vs closing-wedge osteotomies in 5 pairs of cadaver knees. The results showed that at 5 degrees osteotomy, the closing-wedge provided superior results of load transfer from medial to lateral compartment than that seen with opening-wedge, but at 10 degrees osteotomy, there was no significant difference in load transfer in the knee compartments between the 2 surgery modes.

A biomechanical study of bankart lesion fixation - biodegradable ArthroRivet tack vs. suture repair.

Bioabsorbable fixation is commonly used in soft tissue procedures performed in the shoulder. ArthroRivettrade mark tacks (referred to as rivets here), made from a copolymer of 82% poly-L-lactic acid and 18% polyglycolic acid, were developed for the Bankart procedure. Although a previous in vivo study demonstrated favorable comparison of the fixation strength and absorption characteristics of this device with that of polyglyconate bioabsorbable tacks, there have been no published biomechanical studies of this rivet in the shoulder. Fourteen shoulders were harvested from fresh-frozen cadavers of average age 74 years (46-89). Biomechanical testing was performed by measuring the energy, or work, required to anteriorly displace the humeral head 6 mm from the glenoid. Each shoulder was tested intact, vented, and before and after repair of a simulated Bankart lesion at 0, 45, and 90 degrees of abduction with and without maximal external rotation. Overall, the average work required ranged from 54.7 N-mm to 178.27 N-mm. Although the biomechanical performance of the rivet, based on resistance to anterior displacement of the humeral head, was indistinguishable from that of the suture repair, the statistical power of the test was low due to the large variance in the cadaver specimens. The results, in general, correlated well with those of previously published studies, suggesting the suitability of the bioabsorbable rivet for use in Bankart repair.

Distal tibiofibular syndesmosis fixation: a cadaveric, simulated fracture stabilization study comparing bioabsorbable and metallic single screw fixation.

Metal screws that are used for ruptured tibiofibular syndesmosis repair are often removed within 3 months of placement, suggesting the utility of bioabsorbable screws. A biomechanical study was performed to compare fixation of a simulated syndesmosis separation with a 5-mm oriented copolymer bioabsorbable (82:18 poly-L-lactic acid/poly-glycolic acid) versus a stainless steel screw. Eight pairs of cadaveric lower-leg specimens were cleaned and a pronation external rotation-type injury was created in each. The syndesmosis was fixed with a single, tricortical bioabsorbable screw in 1 ankle and a metal screw in the contralateral ankle (matched pairs). Sequential testing of the specimens showed that torsional stiffness of the fixed, relative to intact, specimens was nearly equivalent (0.730 +/- 0.260 for copolymer, 0.770 +/- 0.300 for stainless steel; P = .401). Application of 1000 cycles of axial load (90 to 900 N) resulted in a significant decrease ( P < .0001) in axial stiffness for each fixation method, but the relative decrease was equivalent for both ( P = .211). Failure torque (17.8 +/- 8.3 N.m copolymer, 21.0 +/- 11.5 N.m stainless steel; P = .238) and angle of rotation at failure (47.9 +/- 13.6 degrees copolymer, 42.0 +/- 11.5 degrees stainless steel; P = .199) were also nearly equivalent. It appears that the 5.0-mm diameter copolymer screw is biomechanically equivalent to the 5.0-mm diameter stainless steel screw for repair of syndesmosis disruption.

Bioabsorbable screw fixation in coracoclavicular ligament reconstruction.

The purpose of this study is to evaluate the biomechanical properties of stainless steel and bioabsorbable screw fixation of the clavicle to the base of the coracoid. Seven matched pairs of fresh frozen shoulders were prepared by removing all soft tissue except the acromioclavicular and coracoclavicular ligament complexes. The shoulders were randomly selected and fixed with 4.5-mm stainless steel (SS) screws, while contralateral shoulders were fixed with 4.5-mm poly L-lactic acid polymer (PLLA) screws. Pullout strength, stiffness, and elongation to failure were measured using an Instron Mechanical Tester (Model 4202). The average pullout strength of 720.6 +/- 244.9 N of the metal screws was not statistically different (p = 0.089) from that of the biodegradable screws of 580.4 +/- 188.6 N. The pullout strengths exerted by both these screws exceeded the reported strength (500 N) of the intact coracoclavicular complex indicating adequate initial pullout strength for coracoclavicular fixation.