Molecular Biomarkers for In Vitro Thrombogenicity Assessment of Medical Device Materials.

To develop standardized in vitro thrombogenicity test methods for evaluating medical device materials, three platelet activation biomarkers, beta-thromboglobulin (ß-TG), platelet factor 4 (PF4), soluble p-selectin (CD62P), and a plasma coagulation marker, thrombin-antithrombin complex (TAT), were investigated. Whole blood, drawn from six healthy human volunteers into Anticoagulant Citrate Dextrose Solution A was recalcified and heparinized over a concentration range of 0.5-1.5 U/mL. The blood was incubated with test materials with different thrombogenic potentials for 60 min at 37°C, using a 6 cm2/mL material surface area to blood volume ratio. After incubation, the blood platelet count was measured before centrifuging the blood to prepare platelet-poor plasma (PPP) and platelet-free plasma (PFP) for enzyme-linked immunosorbent assay analysis of the biomarkers. The results show that all four markers effectively differentiated the materials with different thrombogenic potentials at heparin concentrations from 1.0 to 1.5 U/mL. When a donor-specific heparin concentration (determined by activated clotting time) was used, the markers were able to differentiate materials consistently for blood from all the donors. Additionally, using PFP instead of PPP further improved the test method's ability to differentiate the thrombogenic materials from the negative control for ß-TG and TAT. Moreover, the platelet activation markers were able to detect reversible platelet activation induced by adenosine diphosphate (ADP). In summary, all three platelet activation markers (ß-TG, PF4, and CD62P) can distinguish thrombogenic potentials of different materials and detect ADP-induced reversible platelet activation. Test consistency and sensitivity can be enhanced by using a donor-specific heparin concentration and PFP. The same test conditions are applicable to the measurement of coagulation marker TAT.

In Vivo Evaluation of Safety and Efficacy of Ethyl Cellulose-Ethanol Tissue Ablation in a Swine Cervix Model.

Current therapies for treating cervical dysplasia are often inaccessible in low and middle-income countries (LMICs), highlighting the need for novel low-cost therapies that can be delivered at the point of care. Ethanol ablation is a low-cost therapy designed to treat locoregional cancers, which we augmented into an ethyl cellulose (EC)-ethanol gel formulation to enhance its efficacy. Here, we evaluated whether EC-ethanol ablation is able to safely achieve an ablation zone comparable to thermocoagulation, a commonly used therapy for cervical dysplasia. The study was performed in 20 female Yorkshire pigs treated with either a single 500 µL injection of EC-ethanol into the 12 o'clock position of the cervix or a single application of thermocoagulation at 100 °C for 20 s. The average temperature, heart rate, respiratory rate, and blood oxygen remained within normal ranges throughout the EC-ethanol procedure and were similar to the thermocoagulation group. No major side effects were observed. The reproductive tracts were excised after 24 h to examine ablation zones. Comparable depths of necrosis were seen for EC-ethanol (18.6 ± 1.6 mm) and thermocoagulation (19.7 ± 4.1 mm). The volumes of necrosis induced by a single injection of EC-ethanol (626.2 ± 122.8 µL) were comparable to the necrotic volumes induced by thermocoagulation in the top half of the cervices (664.6 ± 168.5 µL). This suggests that two EC-ethanol injections could be performed (e.g., at the 12 and 6 o'clock positions) to achieve comparable total necrotic volumes to thermocoagulation and safely and effectively treat women with cervical dysplasia in LMICs. This is the first study to systematically evaluate EC-ethanol ablation in a large animal model and compare its safety and efficacy to thermocoagulation, a commonly used ablative therapy for cervical dysplasia.