Determination of hexavalent chromium in textiles of daily use by ion chromatography and dermal risk assessment.

The determination of hexavalent chromium in textiles and clothes is challenging since during extraction, the original oxidation state should not be altered. Since, as a matter of fact, current analytical methods are focused only on total chromium determination, the purpose of this research is to develop a reliable analytical method for the determination of Cr(VI) in textiles and tissues of daily use for a reliable application of risk analysis models, which are usually based on total Cr data. After optimization, a 0.0025 M Na3PO4 extraction solution was selected for the extraction of Cr(VI) from textiles. This solution minimizes possible interconversion redox reactions and interference, and provides good extraction recoveries (88.4 ± 2.5% - 105.5 ± 0.6 %, according to Cr(VI) concentration) and quantitation limits (0.017 mg/kg), fully complying the current limits set for Cr(VI) in textiles in contact with skin, and for leachable Cr(VI). The developed method was validated investigating intra-day repeatability (n = 10) and inter-day repeatability (n = 30) which were below 12%, and matrix effect which was below 6% confirming the precision of the method and the negligibility of a matrix interference during the whole analysis. The method, which was proved to be suited also for bioaccessibility studies in saliva and sweat, was applied to the analysis of tank top, coloured paper napkin, polyamide tights, panties, highlighting Cr(VI) content in the panties only at very low concentration (0.028 mg/kg). As verified by ECHA and US EPA approaches, this amount does not pose a non-carcinogenic risk for human health. As regards carcinogenic risk, considering both adult and child exposure, the dermal contact with the panties poses an acceptable risk (R ≤ 10-6).

Feasibility of a Heterogeneous Nanoscale Zero-Valent Iron Fenton-like Process for the Removal of Glyphosate from Water.

Glyphosate is a widely used herbicide, and it is an important environmental pollutant that can have adverse effects on human health. Therefore, remediation and reclamation of contaminated streams and aqueous environments polluted by glyphosate is currently a worldwide priority. Here, we show that the heterogeneous nZVI-Fenton process (nZVI + H2O2; nZVI: nanoscale zero-valent iron) can achieve the effective removal of glyphosate under different operational conditions. Removal of glyphosate can also take place in the presence of excess nZVI, without H2O2, but the high amount of nZVI needed to remove glyphosate from water matrices on its own would make the process very costly. Glyphosate removal via nZVI--Fenton was investigated in the pH range of 3-6, with different H2O2 concentrations and nZVI loadings. We observed significant removal of glyphosate at pH values of 3 and 4; however, due to a loss in efficiency of Fenton systems with increasing pH values, glyphosate removal was no longer effective at pH values of 5 or 6. Glyphosate removal also occurred at pH values of 3 and 4 in tap water, despite the occurrence of several potentially interfering inorganic ions. Relatively low reagent costs, a limited increase in water conductivity (mostly due to pH adjustments before and after treatment), and low iron leaching make nZVI-Fenton treatment at pH 4 a promising technique for eliminating glyphosate from environmental aqueous matrices.

Microwave-assisted extraction and gas chromatographic determination of thirty priority micropollutants in biowaste fraction derived from municipal solid waste for material recovery in the circular-economy approach.

European and national waste directives prioritize recycling of wastes, as well as material and energy recovery from wastes themselves. Bio-waste fraction can be converted into new resources whose quality is strictly dependent upon that of waste feedstock. Methods to evaluate the contamination from organic micropollutants in bio-waste are rarely investigated. The aim of this work was to develop an innovative analytical method for the extraction and quantification of 16 polycyclic aromatic hydrocarbons (PAHs) and 14 polychlorinated biphenyls (PCBs, including dioxin-like compounds) in bio-waste. Through a full-factorial experimental design, a microwave-assisted extraction technique was optimized to extract the thirty targeted micropollutants, studying the effect of cyclohexane and dichloromethane as extraction solvents with or without acetone, and of extraction temperature. Purification of the extract was obtained by a silica-based solid-phase extraction cartridge, followed by a sulfuric acid treatment. The analysis was carried out by gas chromatography coupled with mass spectrometry. The optimized method, validated directly in the bio-waste matrix fortified with isotopically marked surrogates, is characterized by good extraction recoveries, included within 47 and 106% (relative standard deviations <10%), by satisfactory intra-day (<1.1%) and inter-day (<9.3%) precision, and by low matrix effect (<17%), despite the complexity of the matrix. The optimized procedure, applied to the analysis of PAHs and PCBs in a bio-waste sample collected from a local anaerobic digestion and composting plant, showed a total PAHs content of 562 µg/kg. As regards PCBs, the dioxin-like congener PCB 118 was the only compound quantified (25 ± 6 µg kg-1).

A Review on the Degradation of Pollutants by Fenton-Like Systems Based on Zero-Valent Iron and Persulfate: Effects of Reduction Potentials, pH, and Anions Occurring in Waste Waters.

Among the advanced oxidation processes (AOPs), the Fenton reaction has attracted much attention in recent years for the treatment of water and wastewater. This review provides insight into a particular variant of the process, where soluble Fe(II) salts are replaced by zero-valent iron (ZVI), and hydrogen peroxide (H2O2) is replaced by persulfate (S2O82-). Heterogeneous Fenton with ZVI has the advantage of minimizing a major problem found with homogeneous Fenton. Indeed, the precipitation of Fe(III) at pH > 4 interferes with the recycling of Fe species and inhibits oxidation in homogeneous Fenton; in contrast, suspended ZVI as iron source is less sensitive to the increase of pH. Moreover, persulfate favors the production of sulfate radicals (SO4•-) that are more selective towards pollutant degradation, compared to the hydroxyl radicals (•OH) produced in classic, H2O2-based Fenton. Higher selectivity means that degradation of SO4•--reactive contaminants is less affected by interfering agents typically found in wastewater; however, the ability of SO4•- to oxidize H2O/OH- to •OH makes it difficult to obtain conditions where SO4•- is the only reactive species. Research results have shown that ZVI-Fenton with persulfate works best at acidic pH, but it is often possible to get reasonable degradation at pH values that are not too far from neutrality. Moreover, inorganic ions that are very common in water and wastewater (Cl-, HCO3-, CO32-, NO3-, NO2-) can sometimes inhibit degradation by scavenging SO4•- and/or •OH, but in other cases they even enhance the process. Therefore, ZVI-Fenton with persulfate might perform unexpectedly well in some saline waters, although the possible formation of harmful by-products upon oxidation of the anions cannot be ruled out.

Amino groups modified SBA-15 for dispersive-solid phase extraction in the analysis of micropollutants by QuEchERS approach.

In the analysis of contaminants in food products, sample preparation is performed by proper adsorbents, whose choice is crucial to eliminate matrix interference. In this work we modified SBA-15 adsorbents by functionalization with (3-aminopropyl)-triethoxysilane (SBA-15-APTES) and N-[3-(trimethoxysilyl)propyl]aniline (SBA-15-AN) aiming to use them for the first time in the clean-up step of a QuEChERS (quick, easy, cheap, effective, rugged and safe) extraction of micropollutants from strawberry, a sugar rich fruit. After physico-chemical characterization by nitrogen adsorption, infrared spectroscopy and thermogravimetric analysis, the adsorption capabilities of SBA-15 sorbents and possible interaction mechanisms were studied at different pH (2.1-8.5) for glucose, sucrose and fructose at concentrations characteristic of those found in strawberries. The performance of the two SBA-15 sorbents was compared with that of commercial PSA (primary secondary amine), usually proposed in QuEChERS protocols. Both SBA-15 materials exhibit up to 30% higher adsorption than PSA, suggesting their possible QuEChERS application. Synthesized SBA-15 adsorbents were hence used as innovative dispersive sorbents in the QuEChERS extractions of 13 PAHs and 14 PCBs from strawberry. For PCBs, SBA-15-AN provides better matrix removal than PSA and comparable extraction recoveries around 90%. For PAHs, the use of SBA-15-AN has the advantage of lower relative standard deviation (7%) than PSA (19%).

Extraction of Polycyclic Aromatic Hydrocarbons and Polychlorinated Biphenyls from Urban and Olive Mill Wastewaters Intended for Reuse in Agricultural Irrigation.

BACKGROUND: Domestic and industrial wastewater can be introduced in a reuse chain for irrigation purposes. OBJECTIVE: In this paper, we developed analytical procedures for the extraction of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) along a wastewater reuse chain for irrigation purposes. Besides urban wastewaters, olive mill wastewater (OMWW) was considered as a potential water source. Wastewaters were purified by different treatments (urban wastewater plants, pilot-activated sludge, and constructed wetland) and used for the irrigation of olive trees. Suitable extraction procedures were used to analyze treated and untreated wastewaters, soils, and postirrigation leachates. RESULTS: For wastewater and leachate samples, the optimized reverse-phase solid-phase extraction (SPE) provided recoveries up to 79%. For OMWW, the SPE procedure was preceded by a normal-phase purification stage with silica gel for the removal of polyphenols, which were as high as 8.7 g/L. After optimization, extraction recoveries in blank solutions were in the range 20-67% and moderately reduced (10-38%) in OMWW as a result of the matrix effect (ME; -10/-60%) ascribed to the very high value of chemical oxygen demand (264 g/L). LODs of the method were below 1.1 µg/L (PAHs) and 3.2 µg/L (PCBs) using GC-MS analysis. For soil samples of different compositions, microwave-assisted extraction (MAE) provided better extraction recoveries and reproducibility than the more common quick, easy, cheap, effective, rugged, and safe approach, which was affected by a high ME. The LODs of the MAE/GC-MS method were below 4.9 µg/kg (PAHs) and 12.3 µg/kg (PCBs). CONCLUSIONS: The analytical procedures developed are a valuable tool to quantify the possible propagation of residual contamination from PAHs/PCBs with irrigation along the wastewater reuse chain.

Determination of phthalate diesters and monoesters in human milk and infant formula by fat extraction, size-exclusion chromatography clean-up and gas chromatography-mass spectrometry detection.

A sensitive and reliable analytical method was developed for the simultaneous determination of five phthalate diesters and corresponding monoesters in human milk samples and infant formulas. The method involved a liquid-liquid extraction with a CH2Cl2/CH3OH/NaCl 30% 2/1/0.5 (v/v/v) mixture, the clean-up of the extract by size-exclusion chromatography (swelling and elution solvent: cyclohexane/ethyl acetate 9/1v/v), the derivatization of monoesters by trimethylsilyl-diazomethane and instrumental analysis by gas chromatography coupled with mass spectrometry. Recovery was in the range of 83-115% and precision was found between 9% and 21%. For phthalate diesters, method detection limits (MDLs) ranged from hundreds of ng/kg to 4.2µg/kg on a fresh weight milk (f.w.) basis, depending on blank contribution evaluated in matrix. Lower MDLs (0.03-0.8µg/kg f.w.) were achieved for corresponding monoesters. The proposed method was applied to the determination of target compounds in nine human milk samples and four infant formulas, confirming their presence in all samples. However, a generally higher contamination was assessed in artificial milk than in breast milk samples.

Chromium, nickel, and cobalt in cosmetic matrices: an integrated bioanalytical characterization through total content, bioaccessibility, and Cr(III)/Cr(VI) speciation.

The presence of certain metals naturally contained inside raw materials (e.g., pigments) used to produce cosmetics for make-up may represent a serious concern for the final quality and safety of the product. The knowledge of the total concentration of metals is not sufficient to predict their reactivity and their toxicological profile. For these reasons, we set up a comprehensive approach to characterize the content of Co, Cr, and Ni in two raw materials for cosmetic production, a black iron oxide and a pearly pigment, and in a finished product, pearly powder eye shadow. Namely, besides the total metal concentrations, the speciation of chromium and the bioaccessibility of the three metals were assessed. Since no standard method is so far available for hexavalent chromium extraction from cosmetic samples, three approaches were compared (EPA 3060A method, IRSA 16 method, and a Na3PO4 extraction). Results show that Na3PO4 extraction is the most selective one. Cr(VI) was undetectable in black iron oxide and present at very low concentrations (about 0.3 mg/kg) in pearly pigment and in the pearly powder eye shadow samples. The extracted Cr(VI) concentrations are not related to the total Cr content in the samples. Bioaccessibility studies were performed by in vitro extractions with synthetic lacrimal fluids and sweat. Despite the wide range of metal concentrations in the samples, the amounts of bioaccessible elements were undetectable or very low (less than 0.4 mg/kg), thus suggesting that metals in the three samples are present in inert forms. Graphical abstract The possible leaching of metals from cosmetics to biological fluids. Spectroscopic and chromatographic techniques provide complementary information for an integrated bioanalytical approach to risk characterization.

New approaches for extraction and determination of betaine from Beta vulgaris samples by hydrophilic interaction liquid chromatography-tandem mass spectrometry.

Betaine is one of most studied biologically active compounds, due its role in the main biological processes. Although it may be found in several plants and roots, such as the Beta vulgaris family, present in typical diets, just a few analytical methods have been developed for its extraction from roots. A new, quick and effective procedure for the isolation and determination of betaine from two different varieties of B. vulgaris (red and gold) is presented. For betaine extraction, an accelerated solvent extraction (ASE) was coupled with solid-phase extraction. For betaine determination, a separation method based on hydrophilic interaction chromatography coupled with tandem mass spectrometry was optimized for a sensible detection of betaine by means of experimental design. Recoveries were about 93%, with RSD <5%, for both the matrices, without evidence of interfering species. The total content of betaine in extracts of various parts of plants (juice, peel, root) have been determined, obtaining concentrations in the range 3000-4000 mg/L for the juice and in the range 2-5 mg/g for the pulp and for the peel. The B. vulgaris gold species exhibited a higher concentration of betaine, compared to the red variety. Additionally, a micro extraction by packed sorbent technique and a modified quick, easy, cheap, rugged and safe (QuEChERS) procedure, were also tested and compared. Despite the lower recoveries of the latter, with respect to the ASE/SPE procedure (75-89%, RSD <1.5%), the ease of the method, which can be applied without the SPE purification procedure, can represent a positive improvement. Graphical abstract Determination of betaine from Beta vulgaris samples.

Functionalized iron oxide/SBA-15 sorbent: investigation of adsorption performance towards glyphosate herbicide.

Glyphosate is a worldwide-used herbicide occurring in many monitoring campaigns. Efficient technologies are currently unavailable for glyphosate removal from waters. In this work, a SBA-15 mesoporous silica-based material (Fe-NH2-SBA-15) was synthesized and studied for the adsorption of glyphosate from waters. In order to promote specific interactions between the sorbent and glyphosate via phosphoric group, iron oxide nanoparticles were encapsulated and a surface functionalization with (3-aminopropyl)triethoxysilane was accomplished. The adsorption of glyphosate on Fe-NH2-SBA-15 was investigated as a function of (i) pH, (ii) ionic strength (I), and (iii) adsorbate to adsorbent ratio (C), using a two-level, three-factor experimental design. The experimental design allowed for understanding the effect of the abovementioned variables and for proposing experimental conditions for quantitative removal (pH = 2.1, I = 1⋅10-2 M and C = 0.35) under both batch and dynamic conditions. Interaction mechanism between glyphosate and Fe-NH2-SBA-15 sorbent was elucidated by studying the adsorption behavior of sorbents derived from the intermediate stages of synthesis and by desorption tests. Fe-NH2-SBA-15 sorbent can be quantitatively regenerated by 12.5 mM NaOH, and can be reused at least for five adsorption/desorption cycles. Quantitative removal of glyphosate from inlet and effluent wastewaters from a wastewater treatment plant is shown.

QuEChERS sample preparation for the determination of pesticides and other organic residues in environmental matrices: a critical review.

Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS) is an extraction and clean-up technique originally developed for recovering pesticide residues from fruits and vegetables. Since its introduction, and until December 2013, about 700 papers have been published using the QuEChERS technique, according to a literature overview carried out using SciFinder, Elsevier SciVerse, and Google search engines. Most of these papers were dedicated to pesticide multiresidue analysis in food matrices, and this topic has been thoroughly reviewed over recent years. The QuEChERS approach is now rapidly developing beyond its original field of application to analytes other than pesticides, and matrices other than food, such as biological fluids and non-edible plants, including Chinese medicinal plants. Recently, the QuEChERS concept has spread to environmental applications by analyzing not only pesticides but also other compounds of environmental concern in soil, sediments, and water. To the best of our knowledge, QuEChERS environmental applications have not been reviewed so far; therefore, in this contribution, after a general discussion on the evolution and changes of the original QuEChERS method, a critical survey of the literature regarding environmental applications of conventional and modified QuEChERS methodology is provided. The overall recoveries obtained with QuEChERS and other extraction approaches (e.g., accelerated solvent extraction, ultrasonic solvent extraction, liquid/solid extraction, and soxhlet extraction) were compared, providing evidence for QuEChERS higher recoveries for various classes of compounds, such as biopesticides, chloroalkanes, phenols, and perfluoroalkyl substances. The role of physicochemical properties of soil (i.e., clay and organic carbon content, as well as cation exchange capacity) and target analytes (i.e., log KOW, water solubility, and vapor pressure) were also evaluated in order to interpret recovery and matrix effect data.