RESUMO
Aims: This study aimed to evaluate the intraoperative pain (IOP) occurrence in situations of symptomatic irreversible pulpitis (SIP) and symptomatic apical periodontitis (SAP). Materials and Methods: Patients who sought emergency care presenting a diagnosis of SIP or SAP were included. IOP was measured with a Visual Analogue Scale (VAS) after five minutes of local anesthesia, during access to the pulp chamber, root canal exploration and at the end of procedures. In cases where pain was reported during treatment, supplementary anesthesia was performed. Pain scores were recorded and analyzed using a generalized estimating equation model with posthoc comparisons. Results: 56 patients were included. 35 had a diagnosis of SIP; and 21 a diagnosis of SAP. Mean preoperative pain scores for SAP and SIP were 6.69 (±1.54) and 6.39 (±1.48), respectively (p>0.05). In patients with SIP, significant differences were observed between: preoperative scores and other time points; scores after five minutes of local anesthesia and other time points; scores during pulp chamber access and at the end of procedures; and scores during root canal exploration and at the end of procedures (p<0.05). In patients with SAP, significant differences were observed between preoperative pain scores with all other time points (p<0.05). Chi-square test indicated an association between diagnosis and the need for supplementary anesthesia (p<0.05). Conclusions: In conclusion, there is a strong relationship between reduction of moderate/severe pain after application of local anesthesia. The need for supplemental anesthesia is significantly associated to the diagnosis of symptomatic irreversible pulpitis.
RESUMO
AIM: This study aimed to use the micro-computed tomography to evaluate the interfacial adaptation and the presence of gaps of NeoMTA Plus, BioRoot RCS, and MTA in the root-end cavities. METHODOLOGY: Thirty standardized bovine roots measuring 15 mm in length were selected. Chemical-mechanical preparation was performed up to instrument #80 and obturation with the cold lateral compaction technique with cement based on zinc oxide and eugenol. The roots were kept at 37°C for 7 days. Afterward, apicectomy of the apical 3 mm and a root-end filling cavity was performed at 3 mm depth. Micro-computed tomography (micro-CT) was performed to measure the volume of the retroactivity. The roots were divided by stratified randomization into three groups according to the retro-end filling material: NeoMTA Plus, BioRoot RCS, and MTA. A new micro-CT was performed to assess the presence of voids in the root-end filling material and between it and the canal wall. One-way ANOVA and Tukey tests were performed using the BioEstat 4.0 program. RESULTS: There was no difference in the initial volume values of the root-end cavities (p > .05). After the insertion of root-end filling materials, the most significant volumes of voids were observed in the NeoMTA Plus group (p < .05), with no difference for the BioRoot RCS and MTA Angelus groups (p > .05). CONCLUSION: Micro-computed tomography showed that MTA and BioRoot RCS have better interfacial adaptation and presented fewer number of gaps than NeoMTA Plus when used as root-end filling materials. RESEARCH HIGHLIGHTS: Micro-computed tomography evaluation of different root-end fillings materials.
Assuntos
Materiais Restauradores do Canal Radicular , Animais , Bovinos , Microtomografia por Raio-X/métodos , Compostos de Cálcio , Guta-Percha , Obturação do Canal Radicular , Silicatos , Cavidade PulparRESUMO
Abstract This study evaluated the setting time, pH, calcium ion release, solubility, and chemical structure of four calcium silicate sealers after ultrasonic activation (UA). Five sealers were evaluated: Sealer Plus (SP - control); Sealer Plus BC (SPBC), Bio C Sealers (BCS), Endosequence BC Sealer (EBC), and BioRoot RCS (BR). Ten groups were created based on the use or not of ultrasonic activation: SP; SP/UA; SPBC; SPBC/UA; BCS; BCS/UA; EBC; EBC/UA; BR; and BR/UA. Setting time was performed based on ISO 6876:2012 and ASTM C266-07 specifications. Solubility at 24hs, based on ISO 6876:2012. pH and calcium release were evaluated at 1, 24, 72, and 168hs. Raman spectroscopy was used to evaluate structural changes. Quantitative data were analyzed using One-Way ANOVA and Tukey post-hoc test (α=5%). Raman spectroscopy results were qualitatively analyzed. Setting times and solubility of all sealers were not affected by UA (p>0.05). The highest solubility was found for BCS, BCS/UA; and BR, BR/UA (p<0.05). After 24hs, calcium silicate sealers had higher pH than SP and SP/UA (p<0.05). BR and BR/UA had the highest pH at all time points. SP and SP/UA had stable pH at all time points. SP and SP/UA had the lowest calcium release values at all time points (p<0.05). EBC and EBC/UA calcium release significantly differ at 24,72 and 168hs (p<0.05). No chemical changes were observed during Raman spectroscopy. In conclusion, ultrasonic activation affected calcium ion release only for EndoSequence BC Sealer. Ultrasonic activation did not influence the initial and final setting time, solubility, pH, and chemical structure of any investigated sealers.
Resumo Esse estudo avaliou o tempo de presa, pH, liberação de íons cálcio, solubilidade e estrutura química de quatro cimentos à base de silicate de cálcio após a ativação ultrassônica . Cinco cimentos foram avaliados: Sealer Plus (SP - control); Sealer Plus BC (SPBC), Bio C Sealers (BCS), Endosequence BC Sealer (EBC) e BioRoot RCS (BR). Dez grupos foram criados com base no uso ou não de ativação ultrassônica: SP; SP/UA; SPBC; SPBC/UA; BCS; BCS/UA; EBC; EBC/UA; BR; e BR/UA. Tempo de presa foi realizado baseado nas especificações ISO 6876:2012 e ASTM C266-07. Solubilidade em 24hs, baseado na ISO 6876:2012. pH e liberação de cálcio foram avaliados em 1, 24, 72 e 168hs. Espectroscopia Raman foi usada para avaliar alterações estruturais. Os dados quantitativos foram analisados utilizando ANOVA de uma via e teste post-hoc de Tukey (α=5%). Os resultados da espectroscopia Raman foram analisados qualitativamente. Os tempos de presa e a solubilidade de todos os cimentos não foram afetados pelo AU (p>0.05). Maior solubilidade foi encontrada para BCS, BCS/AU; e BR, BR/AU (p<0.05). Após 24hs, os cimentos de silicato de cálcio apresentaram pH mais elevado que SP e SP/AU (p<0.05). BR e BR/AU tiveram o pH mais alto em todos os momentos. SP e SP/AU apresentaram pH estável em todos os momentos. SP e SP/AU tiveram os menores valores de liberação de cálcio em todos os momentos (p<0.05). A liberação de cálcio EBC e EBC/AU diferiram significativamente em 24,72 e 168hs (p<0.05). Nenhuma alteração química foi observada durante a espectroscopia Raman. Em conclusão, a ativação ultrassônica afetou a liberação de íons cálcio apenas para o EndoSequence BC Sealer. A ativação ultrassônica não influenciou o tempo de presa inicial e final, a solubilidade, o pH e a estrutura química de nenhum dos cimentos investigados.
RESUMO
Aims: This systematic review aimed to evaluate whether calcium silicate-based sealers are less cytotoxicity and genotoxicity than epoxy resin-based sealers. Materials and Methods: Systematic searches were conducted for studies published up to September 27th, 2022, without restriction for language or year of publication, in the following databases: MEDLINE/PubMed, Scopus, Web of Science and Grey Literature Report. Only in vitrostudies that evaluated the cytotoxicity or genotoxicity of calcium silicate and epoxy resin-based sealers were included. The quality assessment was performed. Results: After duplicate removal and eligibility criteria assessment, a total of thirty-four studies were included. Twenty-eight studies had a low risk of bias, and six studies had amoderate risk of bias. In general, calcium silicate-based sealers had a lower cytotoxic and genotoxic potential than epoxy-resin based sealers.Conclusions: Based on the findings from in vitrostudies, calcium silicate-based sealers are less cytotoxic andgenotoxic than epoxy resin-based sealers
RESUMO
Aims: To investigate whether bioceramicsealers induce a lower incidence and intensity of postoperative pain compared to other sealers. Materials and Methods: Six electronic databases were searched for studies published up to April 2022, following the PICOS strategy: (P) adult patients undergoing root canal treatment or retreatment; (I) root canal filling using bioceramic sealer; (C) root canal filling using other types of sealers; (O) Primary: postoperative pain incidence and/or intensity; Secondary: number of medication intake; (S) randomizedclinical trials. Risk of bias assessment was performed with the revised Cochrane risk of bias tools for randomized trials (RoB 2). Overall certainty of evidence was assessed through the Grading of Recommendations Assessment, Development, and Evaluation (GRADE) tool. Results: Ten studies were included. Eight studies had a low risk of bias, and two had some concerns risk. Meta-analyses showed no differences regarding postoperative pain intensity and incidence between bioceramic sealers and AH Plus. Number of medication intake seemed to be associated to the preoperative diagnosis. Zinc oxide-eugenol sealer demonstrated an intense postoperative pain compared to bioceramic sealers and AH Plus. GRADE analysis showed a low certainty of evidence for all outcomes. Conclusions: There seem to be no differences between bioceramic sealers and AH Plus regarding postoperative pain intensity and incidence. Number of medication intake seem to be associated to the preoperative diagnosis. Zinc oxide-eugenol evoked a more pronounced postoperative pain.
RESUMO
Abstract This study compared the pH and calcium ion release of calcium silicate- (Bio-C Temp) and calcium hydroxide-based (Ultracal XS) medications. Intracanal remnants of both medications were also evaluated using SEM-EDS after the removal protocol. Thirty-five bovine teeth were prepared. Fifteen were filled with Bio-C Temp and 15 with Ultracal XS. Five remained without intracanal medication (control group). Five samples from each experimental time (i.e.. 24, 72, and 168 hours) were used to measure pH and calcium ions release using a digital pH meter and microplate reader, respectively. Afterward, the peaks of the chemical elements composing both medications were analyzed in SEM-EDS. One-way ANOVA and Tukey's post hoc test analyzed the pH and calcium ion release data. Student's t-test compared the medications in each experimental time. SEM-EDS described the percentage of chemical elements in the samples. Bio-C Temp and Ultracal XS showed a significant pH increase from 24 to 168 hours (p<0.05). Ultracal XS showed a higher pH value at 24 hours than Bio-C Temp (p<0.05) but were similar at 72 and 168h (p > 0.05). Calcium ion release did not depend on the experimental period (p > 0.05). Bio-C Temp showed lower calcium ions release than Ultracal XS at 24 hours (p<0.05). SEM-EDS analyses showed the remains of both medications, but the concentration of Si, Al, and W ions was present only in the calcium silicate-based medication. Bio-C Temp presented alkaline pH and a satisfactory calcium ion release over the time. The remaining of both medications were present after the protocols for paste removal.
Resumo Este estudo comparou o pH e a liberação de íons cálcio de medicações intracanais a à base de silicato de cálcio (Bio-C Temp) e à base de hidróxido de cálcio (Ultracal XS). Remanescentes de ambas as medicações também foram avaliados usando microscopia eletrônica de varredura e espectroscopia de dispersão de energia após o protocolo de remoção. Trinta e cinco dentes bovinos foram preparados. Quinze dentes foram preenchidos com Bio-C Temp e 15 com Ultracal XS. Cinco permaneceram sem medicação intracanal (grupo controle). Cinco amostras de cada tempo experimental (ou seja, 24, 72 e 168 horas) foram usadas para medir o pH e a liberação de íons de cálcio usando um medidor de pH digital e um leitor de microplacas, respectivamente. Em seguida, os picos dos elementos químicos que compõem os dois medicamentos foram analisados em microscopia eletrônica de varredura e por espectroscopia de dispersão de energia. Os testes One-way ANOVA e post hoc de Tukey analisaram os dados de pH e liberação de íons cálcio. O teste t de Student comparou as medicações em cada tempo experimental. A microscopia eletrônica de varredura e a espectroscopia de dispersão de energia descreveu a porcentagem de elementos químicos nas amostras. O Bio-C Temp e o Ultracal XS mostraram um aumento significativo de pH de 24 a 168 horas (p<0,05). O Ultracal XS apresentou um valor de pH mais alto em 24 horas do que o Bio-C Temp (p<0,05), mas foi semelhante em 72 e 168h (p > 0,05). A liberação de íons cálcio não dependeu do período experimental (p> 0,05). O Bio-C Temp apresentou menor liberação de íons de cálcio do que Ultracal XS em 24 horas (p<0,05). As análises de microscopia eletrônica de varredura e espectroscopia de dispersão de energia mostraram remanescentes de ambas as medicações, mas a concentração de íons Si, Al e W estavam presentes apenas na medicação à base de silicato de cálcio. O Bio-C Temp apresentou pH alcalino e maior liberação de íons cálcio. Remanescentes de ambas as medicações estiveram presentes após os protocolos de remoção da pasta.
RESUMO
NiTi endodontic instruments for glide path are the most susceptible to fractures inside the root canal, mainly as a result of high torsional stress. Objective: The present study investigated the resistance to torsion and angular deflection of instruments destined for the glide path: ProGlider #16.02; T-File #17.02 and the MK Life #16.02. Materials and methods: Thirty rotating NiTi glide path instruments (n=10) with 25mm lengths were selected. The torsion test was performed based on ISO 3630-01 (1992). Three millimeters from the tip of the instruments, it was attached to a small load cell by a lever arm connected to the torsion shaft. Torsional strength and angular deflection were evaluated. Fracture surfaces were examined by scanning electron microscopy with magnifications of 1000x and 5000x in the cross section, and 50x in the lateral section. Statistical analysis was performed using the Kruskal-Wallis H test, followed by the Down's post hoc test. Results: The ProGlider instrument showed greater torsional strength (p<0.05) compared to the T-File (p<0.05) and MK Life (p<0.05), respectively. However, the T-File showed greater angular deflection (p<0.05) than the other groups tested. Conclusion: It can be concluded that the ProGlider instrument presented greater torque for the fracture, while the T-File instrument presented greater angular deflection.
RESUMO
This study aims to evaluate, by micro-computed tomography, the filling capacity of two root canal dressings (RCD) - Bio-C Temp and Ultracal - after different activation protocols in teeth with simulated internal root resorption. Eighty single-rooted bovine teeth were sectioned in the cervical portion, standardizing the roots at 16 mm. Then, the canals were prepared by the apex-crown technique until instrument #80 using 2mL of 2.5% sodium hypochlorite solution at each instrument change. Afterward, the roots were sectioned longitudinally, and internal root resorptions were simulated using a diamond bur 1016 at 5 mm from the root apex. Hemiroots were joined and fixed with cyanoacrylate, scanned in micro-computed tomography (micro-CT) to assess total canal volume and simulated internal resorption, and then divided by stratified randomization into experimental groups according to RCD and method of activation (n = 10): Ultracal/Syringe; Ultracal/PUI, Ultracal/XP Endo Finisher, Ultracal Easy Clean, Bio-C Temp/Syringe, Bio-C Temp/PUI, Bio-C Temp/XP Endo Finisher and Bio-C/Easy Clean. Another scanning was performed to assess the volume of voids after RCD activation methods. The ANOVA and Tukey tests compared the activation methods. Student's T-test compared the RCDs within each activation method. Initial root canal volume values were similar for all groups (P > 0.05). There was no difference between activation protocols (P > 0.05). Higher volumes of void spaces were observed for Bio-C Temp compared to Ultracal after all activation methods (P < 0.05), except for Easy Clean (P > 0.05). Due to this, it can be concluded that the agitation methods tested for the Bio-C Temp and Ultracal pastes did not improve the filling of bovine teeth with simulated internal root resorption.
RESUMO
Aims: This study aims to evaluate, by micro-computed tomography, the filling capacity of two root canal dressings (RCD) -Bio-C Temp and Ultracal -after different activation protocols in teeth with simulated internal root resorption.Materials and methods: Eighty single-rooted bovine teeth were sectioned in the cervical portion, standardizing the roots at 16 mm. Then, the canals were prepared by the apex-crown technique until instrument #80 using 2mL of 2.5% sodium hypochlorite solution at each instrument change. Afterward, the roots were sectioned longitudinally, and internal root resorptions were simulated using a diamond bur 1016 at 5 mm from the root apex. Hemiroots were joined and fixed with cyanoacrylate, scanned in micro-computed tomography (micro-CT) to assess total canal volume and simulated internal resorption, and then divided by stratified randomization into experimental groups according to RCD and method of activation (n = 10): Ultracal/Syringe; Ultracal/PUI, Ultracal/XP Endo Finisher, Ultracal Easy Clean, Bio-C Temp/Syringe, Bio-C Temp/PUI, Bio-C Temp/XP Endo Finisher and Bio-C/Easy Clean. Another scanning was performed to assess the volume of voids after RCD activation methods. The ANOVA and Tukey tests compared the activation methods. Student's T-test compared the RCDs within each activation method. Initial root canal volume values were similar for all groups (P > 0.05).Results:There was no difference between activation protocols (P > 0.05). Higher volumes of void spaces were observed for Bio-C Temp compared to Ultracal after all activation methods (P < 0.05), except for Easy Clean (P > 0.05).Conclusion:It can be concluded that the agitation methods tested for the Bio-C Temp and Ultracal pastes did not improve the filling of bovine teeth with simulated internal root resorption.
RESUMO
Aims: This study aims to evaluate, by micro-computed tomography, the filling capacity of two root canal dressings (RCD) -Bio-C Temp and Ultracal -after different activation protocols in teeth with simulated internal root resorption.Materials and methods: Eighty single-rooted bovine teeth were sectioned in the cervical portion, standardizing the roots at 16 mm. Then, the canals were prepared by the apex-crown technique until instrument #80 using 2mL of 2.5% sodium hypochlorite solution at each instrument change. Afterward, the roots were sectioned longitudinally, and internal root resorptions were simulated using a diamond bur 1016 at 5 mm from the root apex. Hemiroots were joined and fixed with cyanoacrylate, scanned in micro-computed tomography (micro-CT) to assess total canal volume and simulated internal resorption, and then divided by stratified randomization into experimental groups according to RCD and method of activation (n = 10): Ultracal/Syringe; Ultracal/PUI, Ultracal/XP Endo Finisher, Ultracal Easy Clean, Bio-C Temp/Syringe, Bio-C Temp/PUI, Bio-C Temp/XP Endo Finisher and Bio-C/Easy Clean. Another scanning was performed to assess the volume of voids after RCD activation methods. The ANOVA and Tukey tests compared the activation methods. Student's T-test compared the RCDs within each activation method. Initial root canal volume values were similar for all groups (P > 0.05).Results:There was no difference between activation protocols (P > 0.05). Higher volumes of void spaces were observed for Bio-C Temp compared to Ultracal after all activation methods (P < 0.05), except for Easy Clean (P > 0.05).Conclusion:It can be concluded that the agitation methods tested for the Bio-C Temp and Ultracal pastes did not improve the filling of bovine teeth with simulated internal root resorption
RESUMO
Abstract This study aimed to evaluate the influence of ultrasonic activation (UA) on the physicochemical properties of hydraulic calcium silicate-based sealers. Nine experimental conditions were created based on the hydraulic calcium silicate-based sealers (Bio-C Sealer, Sealer Plus BC and Bio Root RCS) and the ultrasonic activation (no activation [NA], 10 seconds, and 20 seconds). Then the experimental groups were BC-NA, BC-10, BC-20, SPBC-NA, SPBC-10, SPBC-20, BR-NA, BR-10, and BR-20. Activation was performed with an ultrasonic insert 20/.01. The mold for the physicochemical analysis was filled and evaluated according to the ANSI/ADA specification nº. 57: initial and final setting time, flow, radiopacity and solubility. Tests were also performed to evaluate pH and calcium ion release with experimental periods of 1, 24, 72, and 168 hours with a pH meter and colorimetric spectrophotometer. Data were analyzed by one-way analysis of variance and post-hoc Tukey tests. The significance level was set at 5%. The time of UA progressively delayed the initial setting time for all hydraulic calcium silicate-based sealers (p < 0.05). Twenty seconds of UA increased the mean flow values of Sealer Plus BC and Bio-C Sealer compared to NA (p < 0.05). UA did not influence the radiopacity and solubility of the tested sealers (p > 0.05). UA for 20 seconds enhanced the pH levels and the calcium ion release of Sealer Plus BC and Bio-C Sealer at 168h (p < 0.05). UA for twenty seconds interferes with some physicochemical properties of hydraulic calcium silicate-based sealers.
Resumo Este estudo teve como objetivo avaliar a influência da ativação ultrassônica nas propriedades físico-químicas de cimentos de silicato de cálcio. Nove condições experimentais foram criadas com base nos cimentos de silicato de cálcio (Bio-C Sealer, Sealer Plus BC e Bio Root RCS) e na ativação ultrassônica (sem ativação [SA], 10 segundos e 20 segundos). Os grupos experimentais foram BC-SA, BC-10, BC-20, SPBC-SA, SPBC-10, SPBC-20, BR-SA, BR-10 e BR-20. A ativação foi realizada com um inserto ultrassônico 20/.01. O molde para a análise físico-química foi preenchido e avaliado de acordo com a especificação ANSI/ADA nº. 57: tempo de presa inicial e final, escoamento, radiopacidade e solubilidade. Também foram realizados testes para avaliação de pH e liberação de íons cálcio com períodos experimentais de 1, 24, 72 e 168 horas com pHmetro e espectrofotômetro colorimétrico. Os dados foram analisados por análise de variância one-way e testes post-hoc de Tukey. O nível de significância foi estabelecido em 5%. O tempo de AU aumentou progressivamente o tempo de presa inicial para todos os cimentos de silicato de cálcio (p < 0,05). Vinte segundos de AU aumentaram os valores médios de escoamento de Sealer Plus BC e Bio-C Sealer em comparação com SA (P < 0,05). A AU não influenciou a radiopacidade e a solubilidade dos cimentos testados (P > 0,05). AU por 20 segundos aumentou os níveis de pH e a liberação de íons cálcio de Sealer Plus BC e Bio-C Sealer em 168h (P < 0,05). AU por vinte segundos interfere em algumas propriedades físico-químicas dos cimentos de silicato de cálcio.
RESUMO
Introduction: This study aimed to evaluate the dentinal tubule penetration of an endodontic bioceramic sealer, Sealer Plus BC, after three final irrigation protocols. Methods: Thirty distobuccal roots of maxillary molars were selected. Root canal preparation was performed up to an #40.06 instrument (X1 Blue) under 2.5% sodium hypochlorite irrigation. Specimens were randomly divided into three groups (n=10), according to the final irrigation protocol: G-NaOCl (2.5% sodium hypochlorite + PUI), G-SS (0.9% saline solution + PUI) and G-H20 (Deionized water + PUI). After final irrigation protocols, all specimens were irrigated with phosphate buffer solution. Root canal obturation was performed using the single cone technique and Sealer Plus BC, stained with a specific fluorophore. Specimens were transversely sectioned and each root third was evaluated in a confocal scanning laser microscopy. Images obtained were analyzed for sealer penetration in the dentinal tubules. Results: Dentinal tubule penetration of Sealer Plus BC was not observed in any root third, regardless of the final irrigation protocol investigated. Conclusions: Sealer Plus BC dentinal tubule penetration was not observed after none of the protocols tested. Dentinal tubule penetrability of Sealer Plus BC may be related to other factors rather than the final irrigation protocol.
Assuntos
Selantes de Fossas e Fissuras , Selantes de Fossas e Fissuras/uso terapêutico , Cimentos Dentários/uso terapêutico , Hipoclorito de Sódio/uso terapêutico , Soluções Tampão , Bis-Fenol A-Glicidil Metacrilato/análiseRESUMO
Background. This cross-sectional study aimed to evaluate the impact of pain from dental urgencies on the oral health-related quality of life (OHRQoL). Methods. A sample of sixty-eight patients seeking urgent attention to a primary health unit were included. Clinical diagnosis and sociodemographic data were assessed, dental pain measured by visual analog scale (VAS) and numerical pain rating scale (NPRS). The Oral Health Impact Profile-14 (OHIP-14) instrument was used to measure the OHRQoL. Associations were analyzed using the Student t-test, except for types of urgencies, that were evaluated with one-way analysis of variance (ANOVA) test. Results. The most prevalent urgency type was of endodontic origin (81%). There was no difference between pain and other variables. The type of tooth showed significant differences in OHIP-14 scores. Conclusion. Dental urgencies were associated with a high level of pain and impacted negatively on the patients' OHRQoL. The type of tooth had a positive association the OHRQoL measures.
RESUMO
Aim: The aim of this study was identify contamination on absorbent paper points used by students of Dental Clinic III of the Faculty of Dentistry of Federal University of Rio Grande do Sul in the semester 2015/1, in order to warn students and professionals of the area on the importance to sterilize these materials. Material and Methods: In a clinical environment, 180 absorbent paper points we collected (80 of them from the first series and 80 from the second one), from 40 students. After the collection, each one was singly immersed in a microtube containing 1.5 ml of the BHI (Brain Heart Infusion) culture. Positive control was composed by one paper point contaminated by saliva, and negative control was composed by a closed microtube, only with BHI. The microtubes were incubated at 37ºC in bacteriological incubator during 14 days. The microtubes that presented turbidity were considered positive, and those which did not present turbidity were considered negative. Results: The results were analyzed by the Fisher Exact Test, which demonstrated that paper points from the second series presented higher agreement contamination between the paper points collected from each box, when compared to the analyzed boxes from the first series (p=0.03). All the samples observed presented growth of Bacillus spp in the microorganism identification. Conclusions: It is possible conclude that absorbing paper points, when exposed to clinical environment suffer contamination, and the autoclave sterilization is necessary before the use, regardless the commercial brand, in order to ensure the aseptic chain maintenance.