Impact of increasing total knee replacement constraint within a single implant line on coronal stability: an ex vivo investigation.

INTRODUCTION: Despite the existence of diverse total knee implant designs, few data is available on the relationship between the level of implant constraint and the postoperative joint stability in the frontal plane and strain in the collateral ligaments. The current study aimed to document this relation in an ex vivo setting. MATERIALS AND METHODS: Six fresh-frozen lower limbs underwent imaging for preparation of specimen-specific surgical guides. Specimens were dissected and assessed for joint laxity using the varus-valgus stress tests at fixed knee flexion angles. A handheld dynamometer applied tensile loads at the ankle, thereby resulting in a knee abduction-adduction moment of 10 Nm. Tibiofemoral kinematics were calculated using an optical motion capture system, while extensometers attached to medial collateral (MCL) and lateral collateral ligament (LCL) measured strain. Native joint testing was followed by four TKA designs from a single implant line-cruciate retaining, posterior stabilised, varus-valgus constrained and hinged knee (HK)-and subsequent testing after each implantation. Repeated measures linear mixed-models (p < 0.05) were used to compare preoperative vs. postoperative data on frontal plane laxity and collateral ligament strain. RESULTS: Increasing implant constraint reduced frontal plane laxity across knee flexion, especially in deep flexion (r2 > 0.76), and MCL strain in extension; however, LCL strain reduction was not consistent. Frontal plane laxity increased with knee flexion angle, but similar trends were inconclusive for ligament strain. HK reduced joint laxity and ligament strain as compared to the native condition consistently across knee flexion angle, with significant reductions in flexion (p < 0.024) and extension (p < 0.001), respectively, thereby elucidating the implant design-induced joint stability. Ligament strain exhibited a strong positive correlation with varus-valgus alignment (r2 = 0.96), notwithstanding knee flexion angle or TKA implant design. CONCLUSION: The study demonstrated that increasing the constraint of a TKA resulted in lower frontal plane laxity of the knee. With implant features impacting laxity in the coronal plane, consequentially affecting strain in collateral ligaments, surgeons must consider these factors when deciding a TKA implant, especially for primary TKA. LEVEL OF EVIDENCE: V.

Advanced quantitative 3D imaging improves the reliability of the classification of acetabular defects.

INTRODUCTION: Classifying complex acetabular defects in revision total hip arthroplasty (THA) by means of conventional radiographs comes with significant limitations. Statistical shape modelling allows the virtual reconstruction of the native pelvic morphology, hereby enabling an analytic acetabular defect assessment. Our objective was to evaluate the effect of advanced imaging augmented with analytic representations of the defect on (1) intra- and inter-rater reliability, and (2) up- or downscaling of classification scores when evaluating acetabular defects in patients undergoing revision THA. MATERIALS AND METHODS: The acetabular defects of 50 patients undergoing revision THA were evaluated by three independent, fellowship-trained orthopaedic surgeons. Defects were classified according to the acetabular defect classification (ADC) using four different imaging-based representations, namely, standard radiographs, CT imaging, a virtual three-dimensional (3D) model and a quantitative analytic representation of the defect based on a statistical shape model reconstruction. Intra- and inter-rater reliabilities were quantified using Fleiss' and Cohen's kappa scores, respectively. Up- and downscaling of classification scores were compared for each of the imaging-based representations and differences were tested. RESULTS: Overall inter-rater agreement across all imaging-based representations for the classification was fair (κ 0.29 95% CI 0.28-0.30). Inter-rater agreement was lowest for radiographs (κ 0.21 95% CI 0.19-0.22) and increased for other representations with agreement being highest when using analytic defect models (κ 0.46 95% CI 0.43-0.48). Overall intra-rater agreement was moderate (κ 0.51 95% CI 0.42-0.60). Intra-rater agreement was lowest for radiographs (κ 0.40 95% CI 0.23-0.57), and highest for ratings including analytic defect models (κ 0.64:95% CI 0.46-0.82). Virtual 3D models with quantitative analytic defect representations upscaled acetabular defect scores in comparison to standard radiographs. CONCLUSIONS: Using 3D CT imaging with statistical shape models doubles the intra- and inter-rater reliability and results in upscaling of acetabular defect classification when compared to standard radiographs. This method of evaluating defects will aid in planning surgical reconstruction and stimulate the development of new classification systems based on advanced imaging techniques.

The different subtalar ligaments show significant differences in their mechanical properties.

BACKGROUND: Today, the relative contribution of each ligamentous structure in the stability of the subtalar joint is still unclear. The purpose of this study is to assess the material properties of the different ligamentous structures of the subtalar joint. METHODS: Eighteen paired fresh-frozen cadaveric feet were used to obtain bone-ligament-bone complexes of the calcaneofibular ligament (CFL), the cervical ligament (CL) and the anterior capsular ligament-interosseous talocalcaneal ligament complex (ACaL-ITCL). The samples were subjected to uniaxial testing to calculate their respective stiffness and failure load. RESULTS: The stiffness of ACaL-ITCL complex (mean: 150 ± 51 N/mm, 95% confidence interval (CI): 125.0-176.6 N/mm) was significantly higher than both CFL (mean: 55.8 ± 23.0 N/mm, CI: 43.8-67.7 N/mm) and CL (mean: 63.9 ± 38.0 N/mm, CI: 44.4-83.3 N/mm). The failure load of both the ACaL-ITCL complex (mean:382.5 ± 158 N, CI: 304.1-460.8 N) and the CFL (mean:320.4 ± 122.0 N, CI: 257.5-383.2 N) were significantly higher than that of the CL (mean:163.5 ± 58.0 N, CI: 131.3-195.7 N). The injury pattern demonstrated a partial rupture in all CFL and ACaL-ITCL specimens and in 60% of the CL specimens. CONCLUSION: The CFL, CL and ACaL-ITCL show significant differences in their intrinsic mechanical properties. Both the CFL and CL are more compliant ligaments and seem to be involved in the development of subtalar instability. Based on the material properties, a gracilis tendon graft seems more appropriate than a synthetic ligament to reconstruct a CL or CFL. A partial rupture was the most commonly seen injury pattern in all ligaments. A fibular avulsion of the CFL was only rarely seen. The injury patterns need further investigation as they are important to optimize diagnosis and treatment.

Using a patella reduced technique while balancing a TKA results in restored physiological strain in the collateral ligaments: an ex vivo kinematic analysis.

INTRODUCTION: Poor soft tissue balance in total knee arthroplasty (TKA) often results in patient dissatisfaction and reduced joint longevity. Patella-in-place balancing (PIPB) is a novel technique which aims to restore native collateral ligament behavior without collateral ligament release, while restoring post-operative patellar position. This study aimed to assess the effectiveness of this novel technique through a detailed ex vivo biomechanical analysis by comparing post-TKA tibiofemoral kinematics and collateral ligament behavior to the native condition. MATERIALS AND METHODS: Eight fresh-frozen cadaveric legs (89.2 ± 6 years) were tested on a validated dynamic knee simulator, following computed tomography imaging. Specimens were subjected to passive flexion (10-120°), squatting (35-100°), and varus/valgus laxity testing (10 Nm at 0°, 30°, 60°, 90° flexion). An optical motion capture system recorded markers affixed rigidly to the femur, tibia, and patella, while digital extensometers longitudinally affixed to the superficial medial collateral ligament (MCL) and lateral collateral ligament (LCL) collected synchronized strain data. Following native testing, a Stryker Triathlon CR TKA (Stryker, MI, USA) was performed on each specimen and the identical testing protocol was repeated. Statistical analyses were performed using a linear mixed model for functional motor tasks, while Wilcoxon signed-rank test was used for laxity tests (p < 0.05). RESULTS: Postoperative laxity was lower than the native condition at all flexion angles while post-operative ligament strain was lowered only for MCL at 30° (p = 0.017) and 60° (p = 0.011). Postoperative femoral rollback patterns were comparable to the native condition in passive flexion but demonstrated a more pronounced medial pivot during squatting. CONCLUSIONS: Balancing a TKA with the PIPB technique resulted in reduced joint laxity, while restoring collateral ligament strains. The technique also seemed to restore kinematics and strains, especially in passive flexion.

Determination of predisposing scapular anatomy with a statistical shape model-Part II: shoulder osteoarthritis.

HYPOTHESIS AND BACKGROUND: Shoulder osteoarthritis can be divided into different glenoid types (A, B, C, and D) and subtypes. The aim of this study was to investigate if there is an association between the prearthropathy scapular anatomy, shoulder osteoarthritis, and different glenoid types and subtypes. METHODS: Using principal components analysis, a statistical shape model (SSM) of the scapula was constructed from a data set of 110 computed tomographic (CT) scans. These subjects formed the control group. Next, CT scan images of 117 patients with osteoarthritis were classified according to the modified Walch classification. A complete 3-dimensional (3D) scapular bone model was created for every patient, and using the SSM, a reconstruction of their prearthropathy scapular anatomy was performed. Automated 3D measurements were performed in both the patient and control group to obtain glenoid version and inclination, critical shoulder angle (CSA), posterior acromial slope (PAS), lateral acromion angle, scapular offset, and the rotational alignment of the coracoacromial complex. These parameters were compared between controls, patients with osteoarthritis, and glenoid types and subtypes. RESULTS: Mean version and inclination for the control group was 6° retroversion and 8° superior inclination (both SD 4°). The mean CSA, PAS, coracoid-posterior acromion angle, posterior acromion-scapular plane angle, and fulcrum axis ratio were 30° (SD 4°), 64° (SD 8°), 116° (SD 9°), 55° (SD 7°), and 46% (SD 4%), respectively. Patients with osteoarthritis had a significant lower CSA, posterior acromion-scapular plane angle, coracoid-posterior acromion angle, and fulcrum axis ratio (27°, 50°, 111°, and 44%, all P < .001). We found a significant difference between the control group and the respective glenoid types for the following parameters: mean CSA and coracoid-posterior acromion angle for A glenoids (27°, P = .001, and 111°, P = .007); mean version, CSA, PAS, coracoid-posterior acromion angle, posterior acromion-scapular plane angle, and fulcrum axis ratio for B glenoids (11°, 27°, 71°, 111°, 49°, and 43%, all P < .001); and mean version, CSA, and posterior acromion-scapular plane angle for D glenoids (2°, P = .002, 26°, P = .003, and 48°, P = .007). DISCUSSION: There seems to be an association between prearthropathy scapular anatomy and shoulder osteoarthritis. A small lateral extension and less posterior rotation of the acromion is associated with shoulder osteoarthritis and is present in almost all types and subtypes of glenoid morphology. Furthermore, B and D glenoids are associated with, respectively, a more and less pronounced prearthropathy glenoid retroversion.

Dynamic sagittal alignment and compensation strategies in adult spinal deformity during walking.

BACKGROUND CONTEXT: Radiographic evaluation in adult spinal deformity (ASD) offers no information on spinopelvic alignment and compensation during dynamic conditions. Motion analysis offers the potential to bridge the gap between static radiographic and dynamic alignment measurement, increasing our understanding on how ASD impacts function. PURPOSE: This study aimed to explore the changes in sagittal alignment and compensation strategies in ASD between upright standing and walking, compared to control subjects and within different sagittal alignment groups. Ten patients were measured pre- and six months postoperatively to explore the impact of surgical alignment correction on gait. STUDY DESIGN: Prospective study. SAMPLE SIZE: Full protocol: 58 ASD and 20 controls; Spinal kinematic analysis: 43 ASD and 18 controls; Postoperative analysis: 10 ASD. OUTCOME MEASURES: Standing and walking sagittal spinopelvic (thoracic kyphosis (TK), lumbar lordosis (LL), sagittal vertical axis (SVA), pelvis), and lower limb kinematics, spinopelvic changes between standing and walking (∆ ie, difference between mean dynamic and static angle), lower limb kinetics, spatiotemporal parameters, balance (BESTest), patient-reported outcome scores (SRS-22r, ODI, and FES-I) and radiographic parameters. METHODS: Motion analysis was used to assess the standing and walking spinopelvic and lower limb kinematics, as well as the lower limb kinetics during walking. All parameters were compared between controls and patients with ASD, divided in three groups based on their sagittal alignment (ASD 1: decompensated sagittal malalignment; ASD 2: compensated sagittal malalignment; ASD 3: scoliosis and normal sagittal alignment). Ten patients were reassessed 6 months after spinal corrective surgery. Continuous kinematic and kinetic data were analyzed through statistical parametric mapping. RESULTS: All patient groups walked with increased forward trunk tilt (∆SVA=41.43 mm, p<.001) in combination with anterior pelvic tilt (∆Pelvis=2.58°, p<.001) compared to standing, as was also observed in controls (∆SVA=37.86 mm, p<.001; ∆Pelvis=1.62°, p=.012). Patients walked with increased SVA, in combination with decreased LL and alterations in lower limb kinematics during terminal stance and initial swing, as well as altered spatiotemporal parameters. Subgroup analysis could link these alterations in gait to sagittal spinopelvic malalignment (ASD 1 and 2). After surgical correction, lower limb kinematics and spatiotemporal parameters during gait were not significantly improved. CONCLUSIONS: To compensate for increased trunk tilt and pelvic anteversion during walking, patients with sagittal malalignment show altered lower limb gait patterns, which have previously been associated with increased risk of falling and secondary lower limb pathology. Since surgical correction of the deformity did not lead to gait improvements, further research on the underlying mechanisms is necessary to improve our understanding of how ASD impacts function.

The morphological variation of acetabular defects in revision total hip arthroplasty-A statistical shape modeling approach.

Classification and evaluation of acetabular defects remain challenging and are primarily based on qualitative classification methods. That is because quantitative techniques describing variations of acetabular defects and accompanying bone loss volume are not available. This study introduces a new method based on statistical shape models (SSMs) to quantitively describe acetabular defects. This method is then applied to 87 acetabular defects to objectively describe the variations in acetabular defects typically encountered during revision total hip arthroplasty. The absolute bone loss volume, relative bone loss volume, and relative bone loss surface area with respect to the SSM-based pre-diseased anatomy were used to quantify the acetabular bone defects in different segments of the acetabular surface. The absolute bone loss volume of the average defect shape was equal to 37.0 cm3 . The first three principal modes, accounting for 62% of the total shape variation, were found to represent variations in acetabular defect morphology. The first, second, and third principal modes described, respectively, the size of the bone defects, the difference between superomedially and superolaterally migrated defects, and the degree of involvement of the posterior or anterior column. The developed SSM and the introduced approach could be used to create automated and unbiased classification methods based on quantitative data. Moreover, the proposed model and the underlying data provide the basis for a quantitative design approach where the shape and size of new acetabular implants are determined according to clinical variation present in acetabular defects.

Determination of pre-arthropathy scapular anatomy with a statistical shape model: part I-rotator cuff tear arthropathy.

HYPOTHESIS AND BACKGROUND: Rotator cuff tear arthropathy (RCTA) is a pathology characterized by a massive rotator cuff tear combined with acromiohumeral and/or glenohumeral arthritis. The severity of RCTA can be staged according to the Hamada classification. Why RCTA develops in some patients is unknown. Furthermore, in RCTA patients, distinctly different articular damage patterns can develop on the glenoid side as categorized by the Sirveaux classification (glenoid erosion). The goal of this study was to determine whether an association exists between scapular anatomy and RCTA and different severity stages of RCTA, as well as the associated glenoid erosion types. METHODS: A statistical shape model of the scapula was constructed from a data set of 110 computed tomography scans using principal component analysis. Sixty-six patients with degenerative rotator cuff pathology formed the control group. The computed tomography scan images of 89 patients with RCTA were included and grouped according to the Hamada and Sirveaux classifications. A complete 3-dimensional scapular bone model was created, and statistical shape model reconstruction was performed. Next, automated 3-dimensional measurements of glenoid version and inclination, scapular offset, the critical shoulder angle (CSA), the posterior acromial slope (PAS), and the lateral acromial angle (LAA) were performed. All measurements were then compared between controls and RCTA patients. RESULTS: The control group had a median of 7° of retroversion (variance, 16°), 8° of superior inclination (variance, 19°), and 106 mm of scapular offset (variance, 58 mm). The median CSA, PAS, and LAA were 30° (variance, 14°), 65° (variance, 60°), and 90° (variance, 17°), respectively. In terms of inclination, version, scapular offset, and the PAS, we found no statistically significant differences between the RCTA and control groups. For RCTA patients, the median CSA and median LAA were 32° (P ≤ .01) and 86° (P ≤ .01), respectively. For all investigated parameters, we did not find any significant difference between the different stages of RCTA. Patients with type E3 erosion had a different pre-arthropathy anatomy with increased retroversion (12°, P = .006), an increased CSA (40°, P ≤ .001), and a reduced LAA (79°, P ≤ .001). DISCUSSION: Our results seem to indicate that a 4° more inferiorly tilted and 2° more laterally extended acromion is associated with RCTA. RCTA patients in whom type E3 erosion develops have a distinct pre-arthropathy scapular anatomy with a more laterally extended and more inferiorly tilted acromion and a more retroverted glenoid in comparison with RCTA patients with no erosion. The pre-arthropathy scapular anatomy does not seem to differ between patients with different stages of RCTA.

Accurate reconstructions of pelvic defects and discontinuities using statistical shape models.

Treatment of large acetabular defects and discontinuities remains challenging and relies on the accurate restoration of the native anatomy of the patient. This study introduces and validates a statistical shape model for the reconstruction of acetabular discontinuities with severe bone loss through a two-sided Markov Chain Monte Carlo reconstruction method. The performance of the reconstruction algorithm was evaluated using leave-one-out cross-validation in three defect types with varying severity as well as severe defects with discontinuities. The two-sided reconstruction method was compared to a one-sided methodology. Although, reconstruction errors increased with defect size and this increase was most pronounced for pelvic discontinuities, the two-sided reconstruction method was able to reconstruct the native anatomy with higher accuracy than the one-sided reconstruction method. These findings can improve the preoperative planning and custom implant design in patients with large pelvic defects, both with and without discontinuities.

How much bone support does an anatomic glenoid component need?

BACKGROUND: An important reason for failure of anatomic total shoulder arthroplasty is glenoid component loosening. We investigated the effect of backside bone support on the risk of failure of a glenoid component. METHODS: A finite element model was developed. Virtual surgery was performed for 2 types of glenoid components (cemented all polyethylene [PE] vs. metal backed [MB]), both with gradually decreasing backside bone support. Both bone failure and fixation failure were analyzed. The percentages of bone failure and fixation failure in terms of the critical cement volume (CCV) and micromotion-threshold percentage ratio (MTPR) for the PE and MB components, respectively, were defined and compared. RESULTS: For the reference PE model, the percentages of bone failure and fixation failure (CCV) were 17% and 34%, respectively. With eccentric loading for the MB component, the percentages of bone failure and fixation failure (MTPR) were 6% and 3%, respectively. A global increase in failure was observed with decreasing bone support. The increase in fixation failure, starting from the reference values (MTPR vs. CCV), was relatively more pronounced for the MB component (136% vs. 128%). DISCUSSION: Decreasing backside bone support for an anatomic glenoid component leads to an increased risk of fixation and bone failure. For PE components, decreasing backside support to 95% bone support had only a limited effect. In the case of an MB component, we noticed an increase in micromotion and bone failure already starting from 97% bone support. We conclude that an anatomic glenoid component should always be implanted while maximizing backside bone support.

Variability in Hospital Costs of Adult Spinal Deformity Care.

STUDY DESIGN: Retrospective, single-center analysis. OBJECTIVE: To calculate the total clinical hospital cost of the Adult Spinal Deformity (ASD) care trajectory, to explain cost variability by patient and surgery characteristics, and to identify areas of process improvement opportunities. SUMMARY OF BACKGROUND DATA: ASD is associated with a high financial and clinical burden on society. ASD care thus requires improved insights in costs and its drivers as a critical step toward the improvement of value, i.e., the ratio between delivered health outcome and associated costs. METHODS: Patient characteristics and surgical variables were collected following ethical approval in a cohort of 139 ASD patients, treated between December, 2014 and January, 2018. Clinical hospital costs were calculated, including all care activities, from initial consultation to 1 year after initial surgery (excl. overhead) in a university hospital setting. Multiple linear regression analysis was performed to analyze the impact of patient and surgical characteristics on clinical costs. RESULTS: 75.5% of the total clinical hospital cost (&OV0556;27,865) was incurred during initial surgery with costs related to the operating theatre (80.3%), nursing units (11.9%), and intensive care (2.9%) being the largest contributors. 57.5% of the variation in total cost could be explained in order of importance by surgical invasiveness, age, coronary disease, single or multiple-staged surgery, and mobility status. Revision surgery, unplanned surgery due to complications, was found to increase average costs by 87.6% compared with elective surgeries (&OV0556; 44,907 (± &OV0556; 23,429) vs. &OV0556; 23,944 (± &OV0556; 7302)). CONCLUSION: This study identified opportunities for process improvement by calculating the total clinical hospital costs. In addition, it identified patient and treatment characteristics that predict 57.5% of cost variation, which could be taken into account when developing a payment system. Future research should include outcome data to assess variation in value. LEVEL OF EVIDENCE: 4.

Does Unicondylar Knee Arthroplasty Affect Tibial Bone Strain? A Paired Cadaveric Comparison of Fixed- and Mobile-bearing Designs.

BACKGROUND: Unexplained pain in the medial proximal tibia frequently leads to revision after unicondylar knee arthroplasty (UKA). As one of the most important factors for osteogenic adaptive response, increased bone strain following UKA has been suggested as a possible cause. QUESTIONS/PURPOSES: In this study we: (1) performed a cadaver-based kinematic analysis on paired cadaveric specimens before and after mobile-bearing and fixed-bearing UKA; and (2) simultaneously characterized the strain distribution in the anterior and posterior proximal tibia during squatting. METHODS: Five pairs of fresh, frozen full-leg cadaver specimens (four male, one female, 64 years to 87 years) were subjected to a dynamic squatting motion on a kinematic rig to simulate joint loading for a large ROM. Forces were applied to the quadriceps and hamstrings during the simulation while an infrared camera system tracked the location of reflective markers attached to the tibia and femur. Tibial cortical bone strain was measured with stacked strain gauge rosettes attached at predefined anterior and posterior positions on the medial cortex. Pairwise implantation of mobile-bearing (UKAMB) and fixed-bearing implants (UKAFB) allowed a direct comparison of right and left knees from the same donor through a linear mixed model. RESULTS: UKAMB more closely replicated native kinematics in terms of tibial rotation and in AP and mediolateral translation. Maximum principal bone strain values were consistently increased compared with native (anteromedial, mean [± SD] peak strain: 311 µÎµ ± 190 and posterior, mean peak strain: 321 µÎµ ± 147) with both designs in the anteromedial (UKAFB, mean peak strain: 551 µÎµ ± 381, Cohen's d effect size 1.3 and UKAMB, mean peak strain: 596 µÎµ ± 564, Cohen's d effect size 1.5) and posterior (UKAFB, mean peak strain: 505 µÎµ ± 511, Cohen's d effect size 1.3 and UKAMB, mean peak strain: 633 µÎµ ± 424, Cohen's d effect size 2.1) region. However, in the anterolateral region of the medial tibial bone, UKAFB demonstrated the overall largest increase in strain (mean peak strain: 1010 µÎµ ± 787, Cohen's d effect size 1.9), while UKAMB (613 µÎµ ± 395, Cohen's d effect size 0.2) closely replicated values of the native knee (563 µÎµ ± 234). CONCLUSION: In this in vitro cadaver study both UKAMB and UKAFB led to an increase in bone strain in comparison with the native knee. However, in the anterolateral region of the medial tibial plateau, proximal tibial bone strain was lower after UKAMB and UKAFB. Both UKAMB and UKAFB lead to comparable increases in anteromedial and posterior tibial strain in comparison with the native knee. In the anterolateral region of the medial tibial plateau UKA, proximal tibial bone strain was closer to the native knee after UKAMB than after UKAFB. In an attempt to link kinematics and strain behavior of these designs there seemed to be no obvious relation. CLINICAL RELEVANCE: Further clinical research may be able to discern whether the observed differences in cortical strain after UKA is associated with unexplained pain in patients and whether the observed differences in cortical bone strain between mobile-bearing and fixed unicondylar designs results in a further difference in unexplained pain.

Patellar tendon buckling in post-operative total knee arthroplasty patients is more prominent than in healthy controls.

Recent evidence suggests the patellar tendon undergoes buckling during normal knee flexion, which likely contributes to the functioning of the extensor mechanism. Thus, evaluating buckling in patients following total knee arthroplasty (TKA), where extensor mechanism dysfunction remains a common complication, may be relevant. The study goals were to identify whether post-TKA patients exhibit differences in patellar tendon buckling from healthy, similarly-aged adults and whether such buckling correlates with knee and patellar tendon health. Patellar tendon buckling was assessed during passive knee flexion using ultrasound in post-TKA patients (n = 20; 12M, 68 ± 8 years) and compared with previously reported data from healthy adults (n = 12; 12M; 70 ± 8 years). Patients exhibited significantly larger (p < 0.01) buckling magnitude and angles than healthy adults, and reduced distal buckling was linked with better Knee Society Scores (p = 0.04, R2 = 0.24). The greater patellar tendon buckling observed in post-TKA patients could arise due to factors related to the surgery itself (e.g. infrapatellar fat pad resection) or it may be that post-TKA patients had greater patellar tendon buckling before their procedure. Alterations in patellar tendon buckling may predispose individuals to post-surgical complications including instability, anterior knee pain, and extensor mechanism dysfunction, with further work necessary to elucidate potential links.

Can the contralateral scapula be used as a reliable template to reconstruct the eroded scapula during shoulder arthroplasty?

HYPOTHESIS: The contralateral scapula can be used as a reliable template to determine scapular offset, glenoid inclination, and version of the native scapula in view of reconstructing pathologic scapulae. METHODS: Three-dimensional measurements of scapular offset, inclination, and version were performed using data from a set of 50 bilateral computed tomography scans of full scapulae to determine direct side-to-side differences. RESULTS: The scapula pairs had a mean bilateral difference of 2 mm in offset, 2° in inclination, and 2° in version. Ninety percent of the scapula pairs showed an offset difference smaller than 3 mm. In 96% and 94% of the scapula pairs, the inclination difference and version difference, respectively, were smaller than 5°. The maximum bilateral difference for offset, inclination, and version was 6 mm, 6°, and 8°, respectively. DISCUSSION AND CONCLUSION: The anatomic parameters of scapular offset, glenoid inclination, and version are quite symmetrical and fall into the currently technically feasible accuracy of shoulder arthroplasty implantation. The healthy scapula can be used as a template to guide the reconstruction of the glenoid during shoulder arthroplasty planning in the case of unilateral advanced arthropathy.

Screwless scarf osteotomy for hallux valgus: Evaluation of radiologic correction.

BACKGROUND: The scarf osteotomy is a standard procedure to correct hallux valgus. Recent modifications in the technique allow for important translations of the bone fragments without the need for screw fixation. We performed the first prospective analysis of radiographic parameters after a screwless scarf osteotomy. Prospective study of pre- and postoperative standing radiographs of the feet let us quantify angle reduction and shortening, lengthening or lowering of the first metatarsal. METHODS: 100 patients undergoing a screwless scarf osteotomy were evaluated radiographically before and after surgery. The 1-2 IM angle, HVA, length of the first metatarsal, protrusion length and height of the first metatarsal head were measured. RESULTS: The mean 1-2 IM angle was reduced significantly, to a normal range. The mean reduction of the first metatarsal length and protrusion length was 0.3 and 0.14cm respectively. The metatarsal head was lowered 0.3cm on average. CONCLUSIONS: A minimal mean reduction of the first metatarsal length was observed, but it is possible to lengthen the first metatarsal if necessary. In 23% of cases, an increase of protrusion length was obtained. The screwless scarf osteotomy results in a good correction of the 1-2 IM angle and HVA. If necessary, plantarisation of the first metatarsal head could be obtained. Secondary displacement was seen in 1 patient. LEVEL OF EVIDENCE: IIa, prospective controlled trial.

Kinematics of mobile-bearing unicompartmental knee arthroplasty compared to native: results from an in vitro study.

INTRODUCTION: Fixed-bearing unicompartmental knee arthroplasty (UKA) closely replicates native knee kinematics. As few studies have assessed kinematics following mobile-bearing (MB) UKA, the current study aimed to investigate whether MB UKA preserves natural knee kinematics. MATERIALS AND METHODS: Seven fresh-frozen full-leg cadaver specimens were prepared and mounted in a kinematic rig that allowed all degrees of freedom at the knee. Three motion patterns, passive flexion-extension (0°-110° flexion), open-chain extension (5°-70° flexion) and squatting (30°-100° flexion), were performed pre- and post-implantation of a medial MB UKA and compared in terms of rotational and translational knee joint kinematics in the different anatomical planes, respectively. RESULTS: In terms of frontal plane rotational kinematics, MB UKA specimens were in a more valgus orientation for all motion patterns. In the axial plane, internal rotation of the tibia before and after UKA was consistent, regardless of motion task, with no significant differences. In terms of frontal plane, i.e., inferior-superior, translations, the FMCC was significantly higher in UKA knees in all flexion angles and motor tasks, except in early flexion during passive motion. In terms of axial plane, i.e., anteroposterior (AP), translations, during open-chain activities, the femoral medial condyle center (FMCC) tended to be more posterior following UKA relative to the native knee in mid-flexion and above. AP excursions of the FMCC were small in all tested motions, however. There was substantial AP translation of the femoral lateral condyle center during passive motion before and after UKA, which was significantly different for flexion angles > 38°. CONCLUSIONS: Our study data demonstrate that the kinematics of the unloaded knee following MB UKA closely resemble those of the native knee while relative medial overstuffing with UKA will result in the joint being more valgus. However, replacing the conforming and rigidly fixed medial meniscus with a mobile inlay may successfully prevent aberrant posterior translation of the medial femoral compartment during passive motion and squatting motion.

Mechanical Analysis of Extra-Articular Knee Ligaments. Part two: Tendon grafts used for knee ligament reconstruction.

OBJECTIVES: The aim of this study was to provide information about the mechanical properties of grafts used for knee ligament reconstructions and to compare those results with the mechanical properties of native knee ligaments. METHODS: Eleven cadaveric knees were dissected for the semitendinosus, gracilis, iliotibial band (ITB), quadriceps and patellar tendon. Uniaxial testing to failure was performed using a standardized method and mechanical properties (elastic modulus, ultimate stress, ultimate strain, strain energy density) were determined. RESULTS: The elastic modulus of the gracilis tendon (1458±476MPa) (P<0.001) and the semitendinosus tendon (1036±312MPa) (P<0.05) was significantly higher than the ITB (610±171MPa), quadriceps tendon (568±194MPa), and patellar tendon (417±107MPa). In addition, the ultimate stress of the hamstring tendons (gracilis 155.0±30.7MPa and semitendinosus 120.1±30.0MPa) was significantly higher (P<0.001, respectively P<0.05), relative to the ITB (75.0±11.8MPa), quadriceps tendon (81.0±27.6MPa), and patellar tendon (76.2±25.1MPa). A significant difference (P<0.05) could be noticed between the ultimate strain of the patellar tendon (24.6±5.9%) and the hamstrings (gracilis 14.5±3.1% and semitendinosus 17.0±4.0%). No significant difference in strain energy density between the grafts was observed. CONCLUSIONS: Material properties of common grafts used for knee ligament reconstructions often differ significantly from the original knee ligament which the graft is supposed to emulate.

The measurement of medial knee gap width using ultrasound.

INTRODUCTION: Medial knee instability is a key clinical parameter for assessing ligament injury and arthroplasty success, but current methods for measuring stability are typically either qualitative or involve ionizing radiation. The purpose of this study was to perform a preliminary analysis of whether ultrasound (US) could be used as an alternate approach for quantifying medial instability by comparing an US method with an approach mimicking the current gold standard fluoroscopy method. MATERIALS AND METHODS: US data from the medial knee were collected, while cadaveric lower limbs (n = 8) were loaded in valgus (10 Nm). During post-processing, the US gap width was measured by identifying the medial edges of the femur and tibia and computing the gap width between these points. For comparison, mimicked fluoroscopy (mFluoro) images were created from specimen-specific bone models, developed from segmented CT scans, and from kinematic data collected during testing. Then, gap width was measured in the mFluoro images based on two different published approaches with gap width measured either at the most medial or at the most distal aspect of the femur. RESULTS: Gap width increased significantly with loading (p < 0.001), and there were no significant differences between the US method (unloaded: 8.7 ± 2.4 mm, loaded: 10.7 ± 2.2 mm) and the mFluoro method that measured gap width at the medial femur. In terms of the change in gap width with load, no correlation with the change in abduction angle was observed, with no correlation between the various methods. Inter-rater reliability for the US method was high (0.899-0.952). CONCLUSIONS: Ultrasound shows promise as a suitable alternative for quantifying medial instability without radiation exposure. However, the outstanding limitations of existing approaches and lack of true ground-truth data require that further validation work is necessary to better understand the clinical viability of an US approach for measuring medial knee gap width.

The Anterolateral Ligament Has Similar Biomechanical and Histologic Properties to the Inferior Glenohumeral Ligament.

PURPOSE: To characterize the tensile and histologic properties of the anterolateral ligament (ALL), inferior glenohumeral ligament (IGHL), and knee capsule. METHODS: Standardized samples of the ALL (n = 19), anterolateral knee capsule (n = 15), and IGHL (n = 13) were isolated from fresh-frozen human cadavers for uniaxial tensile testing to failure. An additional 6 samples of the ALL, capsule, and IGHL were procured for histologic analysis and determination of elastin content. RESULTS: All investigated mechanical properties were significantly greater for both the ALL and IGHL when compared with capsular tissue. In contrast, no significant differences between the ALL and IGHL were found for any property. The elastic modulus of ALL and IGHL samples was 174 ± 92 MPa and 139 ± 60 MPa, respectively, compared with 62 ± 30 MPa for the capsule (P = .001). Ultimate stress was significantly lower (P < .001) for the capsule, at 13.4 ± 7.7 MPa, relative to the ALL and IGHL, at 46.4 ± 20.1 MPa and 38.7 ± 16.3 MPa, respectively. The ultimate strain at failure was 37.8% ± 7.9% for the ALL and 39.5% ± 9.4% for the IGHL; this was significantly greater (P = .041 and P = .02, respectively) for both relative to the capsule, at 32.6% ± 8.4%. The strain energy density was 7.8 ± 3.1 MPa for the ALL, 2.1 ± 1.3 MPa for the capsule, and 7.1 ± 3.1 MPa for the IGHL (P < .001). The ALL and IGHL consisted of collagen bundles aligned in a parallel manner, containing elastin bundles, which was in contrast to the random collagen architecture noted in capsule samples. CONCLUSIONS: The ALL has similar tensile and histologic properties to the IGHL. The tensile properties of the ALL are significantly greater than those observed in the knee capsule. CLINICAL RELEVANCE: The ALL is not just a thickening of capsular tissue and should be considered a distinct ligamentous structure comparable to the IGHL in the shoulder. The tensile behavior of the ALL is similar to the IGHL, and treatment strategies should take this into account.

Kinematics of a bicruciate-retaining total knee arthroplasty.

PURPOSE: The recently reintroduced bicruciate-retaining Total Knee Arthroplasty (BCR TKA) is an interesting approach in the quest for close replication of knee joint biomechanics and kinematics closer to the native knee. Therefore, this study aimed at providing a detailed biomechanical view on the functional resemblance of BCR TKA to the native knee joint. METHODS: Seven fresh-frozen full leg cadaver specimens (76 ± 10 year) were mounted in a 6 degrees-of-freedom kinematic rig that applied a dynamic squatting motion knee flexion. Two motion patterns were performed pre- and post-implantation of a fixed bearing BCR TKA: passive flexion-extension and squatting while an infrared camera system tracked the location of reflective markers attached to the tibia and femur. Additionally, specimen laxity was assessed using Lachman tests and varus/valgus stress tests in triplicate. RESULTS: Overall, differences in tibiofemoral kinematics between native knee and BCR TKA were small. Some minor differences appeared under the load of a squat: less internal tibial rotation and some minor paradoxical anterior translation of the medial femoral condyle during mid-flexion. BCR TKA may slightly elevate the joint line. Knee laxity as measured by the Lachman and varus/valgus tests was not significantly influenced by BCR TKA implantation. CONCLUSION: As both cruciate ligaments are preserved with BCR TKA the unloaded knee closely resembles native knee kinematics including preserving the rollback mechanism. The loss of the conforming anatomy of menisci and tibial cartilage and replacement via a relatively flat polyethylene inlay may account for the loss of tibial internal rotation and the slight paradoxical AP motion of the medial femoral condyle with BCR TKA. This phenomenon reproduces findings made earlier with fixed bearing unicondylar knee arthroplasty.