Development of a novel biodegradable porous iron-based implant for bone replacement.

Bone replacement and osteosynthesis require materials which can at least temporarily bear high mechanical loads. Ideally, these materials would eventually degrade and would be replaced by bone deposited from the host organism. To date several metals, notably iron and iron-based alloys have been identified as suitable materials because they combine high strength at medium corrosion rates. However, currently, these materials do not degrade within an appropriate amount of time. Therefore, the aim of the present study is the development of an iron-based degradable sponge-like (i.e. cellular) implant for bone replacement with biomechanically tailored properties. We used a metal powder sintering approach to manufacture a cylindrical cellular implant which in addition contains phosphor as an alloying element. No corrosion inhibiting effects of phosphorus have been found, the degradation rate was not altered. Implant prototypes were tested in an animal model. Bone reaction was investigated at the bone-implant-interface and inside the cellular spaces of the implant. Newly formed bone was growing into the cellular spaces of the implant after 12 months. Signs of implant degradation were detected but after 12 months, no complete degradation could be observed. In conclusion, iron-based open-porous cellular biomaterials seem promising candidates for the development of self-degrading and high load bearing bone replacement materials.

Orbital floor repair using patient specific osteoinductive implant made by stereolithography.

The orbital floor (OF) is an anatomical location in the craniomaxillofacial (CMF) region known to be highly variable in shape and size. When fractured, implants commonly consisting of titanium meshes are customized by plying and crude hand-shaping. Nevertheless, more precise customized synthetic grafts are needed to meticulously reconstruct the patients' OF anatomy with better fidelity. As alternative to titanium mesh implants dedicated to OF repair, we propose a flexible patient-specific implant (PSI) made by stereolithography (SLA), offering a high degree of control over its geometry and architecture. The PSI is made of biodegradable poly(trimethylene carbonate) (PTMC) loaded with 40 wt % of hydroxyapatite (called Osteo-PTMC). In this work, we developed a complete work-flow for the additive manufacturing of PSIs to be used to repair the fractured OF, which is clinically relevant for individualized medicine. This work-flow consists of (i) the surgical planning, (ii) the design of virtual PSIs and (iii) their fabrication by SLA, (iv) the monitoring and (v) the biological evaluation in a preclinical large-animal model. We have found that once implanted, titanium meshes resulted in fibrous tissue encapsulation, whereas Osteo-PMTC resulted in rapid neovascularization and bone morphogenesis, both ectopically and in the OF region, and without the need of additional biotherapeutics such as bone morphogenic proteins. Our study supports the hypothesis that the composite osteoinductive Osteo-PTMC brings advantages compared to standard titanium mesh, by stimulating bone neoformation in the OF defects. PSIs made of Osteo-PTMC represent a significant advancement for patients whereby the anatomical characteristics of the OF defect restrict the utilization of traditional hand-shaped titanium mesh.

Successful bony integration of a porous tantalum implant despite longlasting and ongoing infection: Histologic workup of an explanted shoulder prosthesis.

Infection associated with an implant is a complication feared in surgery, as it leads to loosening and dysfunction. This report documents an unexpected good bony integration of a porous tantalum shoulder prosthesis despite infection. A shoulder prosthesis with a porous tantalum glenoidal base plate was retrieved after 3 years of ongoing infection with Staphylococcus spp. Methyl-methacrylate embedded sections of the retrieved glenoidal component were analyzed by optical and scanning electron beam microscopy (SEM). Bone ongrowth and ingrowth were quantified. Bone had formed at the implant surface and within the open cell structure of the porous tantalum. The bone implant contact index was 32%. The bone ingrowth or relative bone area within the open structure was 8.2%, respectively 11.9% in the outer 50% of the thickness. Due to the section thickness, bone ongrowth could best be documented in SEM. Despite long-lasting and ongoing infection, the glenoidal base plate of the prosthesis showed good bony integration upon removal. The bone ingrowth into the porous tantalum was comparable to the values previously reported for the undersurface of retrieved proximal humerus resurfacing implants. Good integration of the implant however did not solve the problem of infection, and related morbidity. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 2924-2931, 2018.

Retrospective analysis of corrosion and ion release from retrieved cast stainless steel tibia plateau leveling osteotomy plates in dogs with and without peri-implant osteosarcoma.

OBJECTIVE To evaluate and compare surface and cross-sectional structure as well as localized electrochemical corrosion and ion release for cast stainless steel (SS) tibia plateau leveling osteotomy (TPLO) plates retrieved from dogs with and without osteosarcoma (OSA) and to compare these findings with similar variables for forged SS TPLO plates retrieved from dogs. SAMPLE 47 TPLO plates explanted from 45 client-owned dogs (22 cast plates from dogs with OSA, 22 cast plates from dogs without OSA, and 3 forged plates from dogs without OSA). PROCEDURES Histologic evaluations of tissue samples collected from implant sites at the time of plate retrieval were performed to confirm implant site tumor status of each dog. Surfaces and metallographic cross sections of retrieved plates were examined, and the microcell technique was used to obtain local electrochemical corrosion and ion release measurements. RESULTS Findings indicated that all cast SS plates demonstrated high spatial variability of their electrochemical surface properties and inhomogeneous superficial and cross-sectional composition, compared with forged plates. Greater metal ion release was observed in cast plates than in forged plates and in cast plates from dogs with OSA than in cast or forged from dogs without OSA. CONCLUSIONS AND CLINICAL RELEVANCE Results suggested that accumulation of metal ions from implants could be a trigger for neoplastic transformation in neighboring cells. Metal ion release caused by corrosion of implants that do not comply with recommended standards of the American Society for Testing and Materials International or the International Organization for Standardization could potentially place patients at increased risk of tumor development.

Collagen density gradient on three-dimensional printed poly(ε-caprolactone) scaffolds for interface tissue engineering.

The ability to engineer scaffolds that resemble the transition between tissues would be beneficial to improve repair of complex organs, but has yet to be achieved. In order to mimic tissue organization, such constructs should present continuous gradients of geometry, stiffness and biochemical composition. Although the introduction of rapid prototyping or additive manufacturing techniques allows deposition of heterogeneous layers and shape control, the creation of surface chemical gradients has not been explored on three-dimensional (3D) scaffolds obtained through fused deposition modelling technique. Thus, the goal of this study was to introduce a gradient functionalization method in which a poly(ε-caprolactone) surface was first aminolysed and subsequently covered with collagen via carbodiimide reaction. The 2D constructs were characterized for their amine and collagen contents, wettability, surface topography and biofunctionality. Finally, chemical gradients were created in 3D printed scaffolds with controlled geometry and porosity. The combination of additive manufacturing and surface modification is a viable tool for the fabrication of 3D constructs with controlled structural and chemical gradients. These constructs can be employed for mimicking continuous tissue gradients for interface tissue engineering.

Platelet-Rich Plasma as an Autologous and Proangiogenic Cell Delivery System.

Angiogenesis is a key factor in early stages of wound healing and is crucial for the repair of vascularized tissues such as the bone. However, supporting timely revascularization of the defect site still presents a clinical challenge. Tissue engineering approaches delivering endothelial cells or prevascularized constructs may overcome this problem. In the current study, we investigated platelet-rich plasma (PRP) gels as autologous, injectable cell delivery systems for prevascularized constructs. PRP was produced from human thrombocyte concentrates. GFP-expressing human umbilical vein endothelial cells (HUVECs) and human bone marrow-derived mesenchymal stem cells (MSCs) were encapsulated in PRP gels in different proportions. The formation of cellular networks was assessed over 14 days by time-lapse microscopy, gene expression analysis, and immunohistology. PRP gels presented a favorable environment for the formation of a three-dimensional (3D) cellular network. The formation of these networks was apparent as early as 3 days after seeding. Networks increased in complexity and branching over time but were only stable in HUVEC-MSC cocultures. The high cell viability together with the 3D capillary-like networks observed at early time points suggests that PRP can be used as an autologous and proangiogenic cell delivery system for the repair of vascularized tissues such as the bone.

Osteointegration of a modular metal-polyethylene surface gliding finger implant: a case report.

INTRODUCTION: Primary press fit and secondary osteointegration is a precondition for component anchoring in articular surface replacements, also in the case of proximal interphalangeal (PIP) joint. Nevertheless, many existing prostheses for the PIP joint have failed to show sufficient osteointegration. CapFlex-PIP(©) implant is a modular metal-polyethylene surface replacement for the PIP joint consisting of a proximal and distal component each having a titanium pore backside, which allows secondary osteointegration at the bone-implant interface. To evaluate osseous integration of this implant, we report a histological analysis of an explantation of a CapFlex-PIP(©) finger implant. CASE PRESENTATION: We present a case of a removed CapFlex-PIP(©) implant due to a soft tissue complication in an 84-year-old woman. The patient received bisphosphonate medication as treatment for osteoporosis. For the histological analysis, the bone-implant contact (BIC) was measured on all stained sections using a Zeiss Axioplan microscope. The summated BIC was 40.7 % for the proximal component and 46.5 % for the distal component of the implant. Histology showed that the implant was in direct contact with the bone at various locations, with no signs of wear or degradation. CONCLUSIONS: This case demonstrates successful osteointegration of the CapFlex-PIP(©) implant. Both components of the investigated implant show osseous integration to an extent which is comparable to that of other load-bearing and articulating implants at different locations in the human body.

Roughness gradients on zirconia for rapid screening of cell-surface interactions: Fabrication, characterization and application.

Roughness is one of the key parameters for successful osseointegration of dental implants. The understanding of how roughness affects cell response is thus crucial to improve implant performance. Surface gradients, which allow rapid and systematic investigations of cell-surface interactions, have the potential to facilitate this task. In this study, a novel method aiming to produce roughness gradients at the surface of zirconia using hydrofluoric acid etching was implemented. The topography was exhaustively characterized at the microscale and nanoscale by white light interferometry and atomic force microscopy, including the analysis of amplitude, spatial, hybrid, functional, and fractal parameters. A rapid screening of the influence of roughness on human mesenchymal stem cell morphology was conducted and potential correlations between roughness parameters and cell morphology were investigated. The roughness gradient induced significant changes in cell area (p < 0.001), aspect ratio (p = 0.01), and solidity (p = 0.026). Nanoroughness parameters were linearly correlated to cell solidity (p < 0.005), while microroughness parameters appeared nonlinearly correlated to cell area, highlighting the importance of multiscale optimization of implant topography to induce the desired cell response. The gradient method proposed here drastically reduces the efforts and resources necessary to study cell-surface interactions and provides results directly transferable to industry. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 2502-2514, 2016.

Radial Shock Wave Devices Generate Cavitation.

BACKGROUND: Conflicting reports in the literature have raised the question whether radial extracorporeal shock wave therapy (rESWT) devices and vibrating massage devices have similar energy signatures and, hence, cause similar bioeffects in treated tissues. METHODS AND FINDINGS: We used laser fiber optic probe hydrophone (FOPH) measurements, high-speed imaging and x-ray film analysis to compare fundamental elements of the energy signatures of two rESWT devices (Swiss DolorClast; Electro Medical Systems, Nyon, Switzerland; D-Actor 200; Storz Medical, Tägerwillen, Switzerland) and a vibrating massage device (Vibracare; G5/General Physiotherapy, Inc., Earth City, MO, USA). To assert potential bioeffects of these treatment modalities we investigated the influence of rESWT and vibrating massage devices on locomotion ability of Caenorhabditis elegans (C. elegans) worms. RESULTS: FOPH measurements demonstrated that both rESWT devices generated acoustic waves with comparable pressure and energy flux density. Furthermore, both rESWT devices generated cavitation as evidenced by high-speed imaging and caused mechanical damage on the surface of x-ray film. The vibrating massage device did not show any of these characteristics. Moreover, locomotion ability of C. elegans was statistically significantly impaired after exposure to radial extracorporeal shock waves but was unaffected after exposure of worms to the vibrating massage device. CONCLUSIONS: The results of the present study indicate that both energy signature and bioeffects of rESWT devices are fundamentally different from those of vibrating massage devices. CLINICAL RELEVANCE: Prior ESWT studies have shown that tissues treated with sufficient quantities of acoustic sound waves undergo cavitation build-up, mechanotransduction, and ultimately, a biological alteration that "kick-starts" the healing response. Due to their different treatment indications and contra-indications rESWT devices cannot be equated to vibrating massage devices and should be used with due caution in clinical practice.

Resurfacing of the humeral head: An analysis of the bone stock and osseous integration under the implant.

Cementless-surface-replacement-arthroplasty (CSRA) of the shoulder aims for functional joint restoration with minimal bone loss. Good clinical results have been reported, but due to the radiopaque metal shell no data is available on the structure, osseous integration, and bone stock under the implant. 14 hemi-CSRAs (4 manufacturers) with two geometries (crown [n = 7]/ stem [n = 7] fixation) were retrieved from patients undergoing revision due to glenoidal erosion. Histological sections cutting through the implant centre and bone were analysed. Quantitative histomorphometry evaluated the bone-implant-contact and compared the bone-area to native humeral retrievals (n = 7). The bone-implant-interface was further assessed by scanning-electron-microscopy (SEM) and energy-dispersive-x-ray (EDX). Qualitative histology revealed a reduced and inhomogeneous bone stock. Obvious signs of stress shielding were observed with bone predominantly visible at the stem and implant rim. Quantitative histomorphometry confirmed the significantly reduced bone-area (9.2 ± 3.9% [crown 9.9 ± 4.3%, stem 8.6 ± 3.6%]) compared to native humeri (21.2 ± 9.1%; p < 0.05). Bone-implant-contact was 20.5 ± 5.8% (crown 21.8 ± 6.2%, stem 19.2 ± 5.6%) which was confirmed by SEM and EDX. Altogether, CRSA shows satisfactory bone ingrowth at the interface suggesting sufficient primary stability to allow osseous integration. However, clear signs of stress shielding with an inhomogeneous and reduced bone stock were observed. The impact on the long-term-results is unclear requiring further investigation.

Straight proximal humeral nails are surrounded by more bone stock in comparison to bent nails in an experimental cadaveric study.

BACKGROUND: In the management of proximal humeral fractures intramedullary implants with bent and straight shape of the proximal part of nail are available. Based on data from previous studies on bone distribution in the humeral head, we hypothesized, that higher densities might exist in the bone stock surrounding straight nails in comparison to their angulated counterparts. With a known positive correlation between bone density and mechanical stability, this could indicate potentially higher rigidity of osteosyntheses done with straight implants. METHODS: We performed high resolution peripheral quantitative computed tomographies of the potential straight and bent implant bearing regions of 27 cadaveric proximal humeri. The acquired data were analyzed for differences between straight and bent Volumes of Interest as well as intra- and interindividual bone stock distribution. RESULTS: For both straight and bent volumes of interest a considerably declining bone mineral density was found in craniocaudal direction. Mean densities of bent volumes were significantly lower in comparison to their corresponding straight counterparts (p < 0.01) Intra-individual comparison yielded high bivariate correlations of the corresponding Volumes of Interest of the right and the left side (p < 0.01). CONCLUSIONS: Based on the volumetric data a statistically relevant biomechanical superiority of straight shaped implants can be assumed. Since we found a rapid decrease of bone density in cranio-caudal direction, intramedullary implants should be anchored as proximally in the subcortical area as possible to minimize the risk of displacement or cutout. The high correlation between the Volumes of Interest of the corresponding right and left sides could aid in preoperative planning when considering an intra- or extramedullary approach.

X-treme CT analysis of cancellous bone at the rotator cuff insertion in human individuals with osteoporosis: superficial versus deep quality.

PURPOSE: Rotator cuff (RC) repair-especially in the elderly population-is problematic since the patients suffer to a high extent from bone mineral density loss at the reattachment site. Therefore, the study was primarily driven by the question whether it is possible to reach more or qualitatively better cancellous bone and thus a more stable postoperative result if anchors with greater length are used for RC repair and/or the conventional anchors are screwed deeper into the bone. In anatomical terms, the question is raised whether cancellous bone is of better quality close to or far off the RC enthesis. METHODS: Axial HRqCT scans (X-tremeCT, Scanco Medical) of 36 human cadaveric humeral heads (75 ± 11 years) were performed to determine the ratio of bone volume to total volume (BV/TV), trabecular thickness (Trab Th), number of trabecles (Trab N), trabecular separation (Trab Sp) as well as non-metric indices such as connectivity density (Conn Dens) and structure model index (SMI). Within the greater tuberosity (GT), 6 volumes of interest (VOI) (A1, B1, C1, A2, B2, C2), in the lesser tuberosity (LT) 2 VOIs (D1, D2) and one control VOI in the subchondral bone were set. The analyzed bone cylinder of each VOI was divided into a superficial and a deep portion. RESULTS: The parameters BV/TV, Trab N, Trab Th and Conn Dens in all volumes of the GT and LT revealed higher values in the superficial portion reaching different levels of significance (p < 0.001/<0.05). The only parameter presenting a higher value in the deep portion was Trab Sp, but this was the case for all GT and LT regions. Interestingly, the difference between the superficial and deep portion reached significance for the non-metric parameter SMI in no volume of the GT/LT, although the higher values were found superficially. CONCLUSIONS: Our data show that cancellous bone presents with decreasing bone quality when analyzing increasingly deeper portions of the bone cylinders of the GT and LT starting at the articular surface. This information seems to be crucial for shoulder surgeons, especially when treating elderly patients. Our results clearly prove that screwing in anchors to a deeper extent will not improve stability, since the deeper bone stock is of worse quality.

Behaviour of ChronOS™ Inject in metaphyseal bone defects of distal radius fractures: tissue reaction after 6-15 months.

Biodegradable calcium phosphate cements are frequently used in human patients but data regarding resorption characteristic of ChronOS™ Inject in metaphyseal bone defects are lacking. Six patients (range 62-81 years) with a dorsally displaced distal radius fracture were treated with volar locking plate systems and ChronOS™ Inject application into the metaphyseal bone defect. During implant removal (time in situ 6-15 months, average 11 months) a 2mm diameter biopsy was obtained from the region of the previous cement injection. In all specimens' area of bone, osteoid and remaining tissue were histomorphometrically determined and presence of cement particles, bone marrow fibrosis and signs of inflammation were recorded. Vital bone tissue, osteoid formation, mast cell occurrence and marrow fibrosis were detected in most specimens. Varying but small amounts of granular material identified as remainder of the cement were detected in all specimens. Agglomerations of granular material were often surrounded by bone tissue and islets of newly formed osteoid in direct contact with the remaining cement also occurred. Bone density (i.e. area per region of interest) ranged between 6.9% and 36.2% and osteoid density between 0.5% and 7.8%. Bone osteoid ratio was higher in patients who received no osteoporosis medication and lower in patients who received osteoporosis medication (range 6.0-32.1). The present study shows that small amounts of ChronOS™ Inject are still detectable in human patients 15 months after implantation into a distal radius bone defect. During tissue remodelling ChronOS™ Inject is integrated into the newly formed trabecular bone meshwork.

Fibrocartilage in various regions of the human glenoid labrum. An immunohistochemical study on human cadavers.

PURPOSE: The nature and the distribution of fibrocartilage at the human glenoid labrum are unclear, and a better understanding may help to restore its function in open and arthroscopic Bankart repair. Aim of this study was to describe the fibrocartilage extent within the labrum at clinically relevant sites of the glenoid in order to relate the molecular composition of the labrum to its mechanical environment. METHODS: Twelve fresh frozen human cadaveric shoulders (mean age 38 years) were obtained, and sections perpendicular to the glenoid rim at the 12, 2, 3, 4, 6 and 9 o' clock position were labelled with antibodies against collagen I and II, aggrecan and link protein. RESULTS: A fibrocartilaginous transition zone with a characteristic collagen fibre orientation was found in 81% of cases, evenly distributed (83-92%) around the glenoid rim. The percentage of labrum cross-sectional area comprised of fibrocartilage averaged 28% and ranged from 26% at 12 o'clock on the glenoid clock face to 30% at 3 o'clock. The highest amount of fibrocartilage (82%) was found in the region neighbouring the hyaline articular cartilage. In the region beyond the bony edge of the glenoid, fibrocartilage cross-sectional area did not exceed 12-17%. CONCLUSION: Fibrocartilage is present at all examined positions around the glenoid rim and constitutes up to 1/3 of the cross-sectional area of the labrum. In turn, the percentage of fibrocartilage in different regions of its cross-section varies considerably. The findings suggest that the penetration of fibrocartilaginous tissue may be reduced by avoiding the highly fibrocartilage transition zone during restoration of labral detachment.

Risk of graft fracture after dorso-ventral thoraco-lumbar spondylodesis: is there a correlation with graft size?

STUDY DESIGN: Retrospective clinical study in patients with dorso-ventral thoraco-lumbar spondylodesis. OBJECTIVE: To investigate whether the ratio between graft cross sectional area and the surface area of the adjacent endplates has any effect on the midterm stability of the spondylodesis. Dorso-ventral spondylodesis in the region of the thoraco-lumbar spine is one of the most frequent operations in orthopaedic surgery. Anterior stabilization with autologous iliac crest graft currently is a standard approach in many hospitals. Although numerous recommendations are given how to perform this technique, no clinical advice is available with regard to minimum graft size. METHODS: Sixty-four-slice CT-scans were obtained from 82 patients 4-12 months after posterior spondylodesis with anterior implantation of iliac crest graft and stabilization with an internal fixator. The scans were analyzed using image analysis software. First, the cross sectional area of the graft was calculated and then the surface area of the adjacent endplates. The ratio between graft cross sectional area and endplate surface area was then calculated from these two values. The grafts were then evaluated in sagittal reconstruction for signs of fracture. RESULTS: The probability for graft fracture in autologous tricortical grafts was >0.1% (p < 0.001) if the graft cross sectional area exceeded 23.9% of the surface area of the adjacent endplates. Patients with lower ratio values had a higher fracture risk and below a value of 10% all grafts fractured. CONCLUSION: The relationship between graft cross sectional area and adjacent endplate area has an important effect on graft midterm stability in ventral spondylodesis of the thoraco-lumbar spine. In our opinion, the risk of graft fractures in dorso-ventral spondylodesis can be reduced by implantation of an appropriately sized graft without any additional procedures or instrumentation.

Confocal imaging protocols for live/dead staining in three-dimensional carriers.

In tissue engineering, a variety of methods are commonly used to evaluate survival of cells inside tissues or three-dimensional (3D) carriers. Among these methods confocal laser scanning microscopy opened accessibility of 3D tissue using live cell imaging into the tissue or 3D scaffolds. However, although this technique is ideally applied to 3D tissue or scaffolds with thickness up to several millimetres, this application is surprisingly rare and scans are often done on slices with thickness <20 µm. Here, we present novel protocols for the staining of 3D tissue (e.g. intervertebral disc tissue) and scaffolds, such as fibrin gels or alginate beads.

Unreamed or RIA reamed nailing: an experimental sheep study using comparative histological assessment of affected bone tissue in an acute fracture model.

The purpose of the present study was to evaluate the Reamer/Irrigator/Aspirator (RIA), a reaming system designed to incorporate the advantages of irrigation and suction for every day clinical use. The evaluation process was focused on the displacement of the medullary content and its impact on cortical perfusion. The results of the RIA reamed nailing were compared to conventional non-reamed nailing (NRN). The tibia of the sheep was used as an acute fracture model. The fracture and nailing procedure was followed by intravital staining with Procion red. The effects on cortical perfusion (Procion red staining) were addressed in polymer embedded sections and cryosections. Sudan III stained cryosections were evaluated with respect to the cortical fat distribution. After irrigation and suction minute amounts of fat were observed in the cortex, whereas after non-reamed nailing the endosteal third of the cortical bone was penetrated with fat. Non-reamed nailing acutely showed better perfusion in the endosteal tenth and periosteal third of the cortical bone, after irrigation and suction reaming perfusion was preserved to a lesser degree. Irrigation and suction significantly reduces fat intravasation, and thus the danger of system-wide damage. Therefore, the Reamer/Irrigator/Aspirator is as efficient as its experimental predecessors.

Comparison of the immature sheep spine and the growing human spine: a spondylometric database for growth modulating research.

STUDY DESIGN: A comparative study on growth of the sheep and human spine. OBJECTIVE: To validate the immature sheep spine as model for the growing human spine and to yield a database for planning and interpretation of future animal experiments. SUMMARY OF BACKGROUND DATA: With the current change of paradigm to nonfusion strategies for pediatric spine deformities, experimental surgery on spines of growing goats, sheep, and pigs has gained importance as preclinical proof-of-concept test. However, despite the proceeding use of animals, there is a lack of knowledge regarding the growth of the sheep spine and the relation to the human spine. METHODS: Thoracic and lumbar cadaver spines were harvested from 50 Swiss alpine sheep. Specimens were obtained from newborn, 1, 3, 6, 9 and 12, 15 and 18 months old female sheep. Direct spondylometry yielded vertebral body heights, widths, and depths and spinal canal size, which were compared to pooled data on human spine growth retrieved from the literature. RESULTS: Sheep spine growth ceases at age 15 to 18 months, which corresponds to a time-lapse model of human growth. Main growth occurs within the first 3 to 6 months of life, as opposed to human spines with maximal growth during the first 4 years and puberty. The relation between sheep and human vertebral shape is continuously changing with growth: at birth, sheep vertebrae are twice as tall, but equally wide and deep. At skeletal maturity, height is 15% to 25% bigger in sheep, but width 15% to 30% and depth 30% to 50% are smaller. CONCLUSION: The immature sheep spine offers fast effects if growth-modulating interventions are performed within the first 3 to 6 months of age. The differences in vertebral shapes and further distinctions between human and sheep spines such as biomechanics, facet anatomy, and rib cage morphology have to be considered when interpreting results after experimental surgery.

Wear mechanisms in metal-on-metal bearings: the importance of tribochemical reaction layers.

Metal-on-metal (MoM) bearings are at the forefront in hip resurfacing arthroplasty. Because of their good wear characteristics and design flexibility, MoM bearings are gaining wider acceptance with market share reaching nearly 10% worldwide. However, concerns remain regarding potential detrimental effects of metal particulates and ion release. Growing evidence is emerging that the local cell response is related to the amount of debris generated by these bearing couples. Thus, an urgent clinical need exists to delineate the mechanisms of debris generation to further reduce wear and its adverse effects. In this study, we investigated the microstructural and chemical composition of the tribochemical reaction layers forming at the contacting surfaces of metallic bearings during sliding motion. Using X-ray photoelectron spectroscopy and transmission electron microscopy with coupled energy dispersive X-ray and electron energy loss spectroscopy, we found that the tribolayers are nanocrystalline in structure, and that they incorporate organic material stemming from the synovial fluid. This process, which has been termed "mechanical mixing," changes the bearing surface of the uppermost 50 to 200 nm from pure metallic to an organic composite material. It hinders direct metal contact (thus preventing adhesion) and limits wear. This novel finding of a mechanically mixed zone of nanocrystalline metal and organic constituents provides the basis for understanding particle release and may help in identifying new strategies to reduce MoM wear.

Detection of bone graft failure in lumbar spondylodesis: spatial resolution with high-resolution peripheral quantitative CT.

OBJECTIVE: In spinal surgery, anterior spondylodesis is often combined with bone grafting, and graft integration is assessed with CT. High-resolution peripheral quantitative CT offers a resolution of 82 mum. The aim of this study was to compare the outcome of anterior spondylodesis as assessed with three radiologic procedures. MATERIALS AND METHODS: Monosegmental lumbar spondylodesis with autologous iliac crest graft or solvent-preserved bovine cancellous bone was performed on seven sheep. The fused spinal segments were explanted after 24 weeks and examined with clinical 64-MDCT, high-resolution peripheral quantitative CT, and contact radiography. In 2D views, the area of the disk space bridged by bone was assessed, and the grafts were examined for fractures. RESULTS: In three of seven sheep, clinical CT erroneously showed stable consolidation, whereas contact radiography revealed a clearly visible graft fracture, as did high-resolution peripheral quantitative CT. There was a statistically significant difference (p = 0.038) between bone volume assessed with clinical CT and that assessed with contact radiography. There was an almost significant difference (p = 0.053) between volumes assessed with high-resolution peripheral quantitative CT and clinical MDCT. CONCLUSION: High-resolution peripheral quantitative CT, a technique approved for clinical use, has higher resolution in imaging of bone structure than does 64-MDCT. Our results show that high-resolution peripheral quantitative CT is superior to 64-MDCT in assessing osseous implant integration after anterior spondylodesis. The specimen size limit, however, prohibits in vivo use of this method in evaluation of the human spine. Our results suggest that in clinical practice, persisting symptoms despite radiologic findings of consolidated spondylodesis may be related to graft failure, which cannot be detected with clinically available methods.