Manipulated Fluoro-Ether Derived Nucleophilic Decomposition Products for Mitigating Polarization-Induced Capacity Loss in Li-Rich Layered Cathode.

Electrolyte engineering is a fascinating choice to improve the performance of Li-rich layered oxide cathodes (LRLO) for high-energy lithium-ion batteries. However, many existing electrolyte designs and adjustment principles tend to overlook the unique challenges posed by LRLO, particularly the nucleophilic attack. Here, we introduce an electrolyte modification by locally replacing carbonate solvents in traditional electrolytes with a fluoro-ether. By benefit of the decomposition of fluoro-ether under nucleophilic O-related attacks, which delivers an excellent passivation layer with LiF and polymers, possessing rigidity and flexibility on the LRLO surface. More importantly, the fluoro-ether acts as "sutures", ensuring the integrity and stability of both interfacial and bulk structures, which contributed to suppressing severe polarization and enhancing the cycling capacity retention from 39 % to 78 % after 300 cycles for the 4.8 V-class LRLO. This key electrolyte strategy with comprehensive analysis, provides new insights into addressing nucleophilic challenge for high-energy anionic redox related cathode systems.

On-chip gas reaction nanolab for in situ TEM observation.

The catalysis reaction mechanism at nano/atomic scale attracted intense attention in the past decades. However, most in situ characterization technologies can only reflect the average information of catalysts, which leads to the inability to characterize the dynamic changes of single nanostructures or active sites under operando conditions, and many micro-nanoscale reaction mechanisms are still unknown. The combination of in situ transmission electron microscopy (TEM) holder system with MEMS chips provides a solution for it, where the design and fabrication of MEMS chips are the key factors. Here, with the aid of finite element simulation, an ultra-stable heating chip was developed, which has an ultra-low thermal drift during temperature heating. Under ambient conditions within TEM, atomic resolution imaging was achieved during the heating process or at high temperature up to 1300 °C. Combined with the developed polymer membrane seal technique and nanofluidic control system, it can realize an adjustable pressure from 0.1 bar to 4 bar gas environment around the sample. By using the developed ultra-low drift gas reaction cells, the nanoparticle's structure evolution at atomic scale was identified during reaction.

Controllable CO adsorption determines ethylene and methane productions from CO2 electroreduction.

Among all CO2 electroreduction products, methane (CH4) and ethylene (C2H4) are two typical and valuable hydrocarbon products which are formed in two different pathways: hydrogenation and dimerization reactions of the same CO intermediate. Theoretical studies show that the adsorption configurations of CO intermediate determine the reaction pathways towards CH4/C2H4. However, it is challenging to experimentally control the CO adsorption configurations at the catalyst surface, and thus the hydrocarbon selectivity is still limited. Herein, we seek to synthesize two well-defined copper nanocatalysts with controllable surface structures. The two model catalysts exhibit a high hydrocarbon selectivity toward either CH4 (83%) or C2H4 (93%) under identical reduction conditions. Scanning transmission electron microscopy and X-ray absorption spectroscopy characterizations reveal the low-coordination Cu0 sites and local Cu0/Cu+ sites of the two catalysts, respectively. CO-temperature programed desorption, in-situ attenuated total reflection Fourier transform infrared spectroscopy and density functional theory studies unveil that the bridge-adsorbed CO (COB) on the low-coordination Cu0 sites is apt to be hydrogenated to CH4, whereas the bridge-adsorbed CO plus linear-adsorbed CO (COB + COL) on the local Cu0/Cu+ sites are apt to be coupled to C2H4. Our findings pave a new way to design catalysts with controllable CO adsorption configurations for high hydrocarbon product selectivity.

Aluminum-Based Metal-Organic Frameworks Derived Al2O3-Loading Mesoporous Carbon as a Host Matrix for Lithium-Metal Anodes.

Li-metal anode attracts great focus owing to its ultra-high specific capacity and the lowest redox potential. However, the uncontrolled growth of Li dendrite leads to severe security issues and limited cycle life. Herein, Al2O3 loading mesoporous carbon (Al2O3@MOF-C) derived from Al-based metal-organic frameworks (Al-MOFs) was investigated as the stable host matrix for Li metal, in which, Al2O3 was served as nano seeds for the Li deposition and decrease the Li nucleation overpotential. Except that, the high specific surface area and wide pore distribution can also buffer the volume changes of Li and fasten electron transfer, hence a dendrite-free morphology was observed even after 50 cycles at 2 mA cm-2. High Li coulombic efficiency of 97.9% after 100 cycles at 1 mA cm-2, 1 mAh cm-2, and 97.6% after 50 cycles at 1 mA cm-2 and 6 mAh cm-2 were performed by Al2O3@MOF-C electrodes. Good performances were also obtained for Li-sulfur and LiFePO4 batteries. The performances of Al2O3@MOF-C@Li were compared with Li foil and Cu@Li in full cell configurations. The electrochemical tests of full cells based on Al2O3@MOF-C@Li indicated that this Al-based functional host matrix can enhance the Li-utilization and lead to significant enhancement of the cycling performance of Li anodes.

Promoting Ethylene Selectivity from CO2 Electroreduction on CuO Supported onto CO2 Capture Materials.

Cu is a unique catalyst for CO2 electroreduction, since it can catalyze CO2 reduction to a series of hydrocarbons, alcohols, and carboxylic acids. Nevertheless, such Cu catalysts suffer from poor selectivity. High pressure of CO2 is considered to facilitate the activity and selectivity of CO2 reduction. Herein, a new strategy is presented for CO2 reduction with improved C2 H4 selectivity on a Cu catalyst by using CO2 capture materials as the support at ambient pressure. N-doped carbon (Nx C) was synthesized through high-temperature carbonization of melamine and l-lysine. We observed that the CO2 uptake capacity of Nx C depends on both the microporous area and the content of pyridinic N species, which can be controlled by the carbonization temperature (600-800 °C). The as-prepared CuO/Nx C catalysts exhibit a considerably higher C2 H4 faradaic efficiency (36 %) than CuO supported on XC-72 carbon black (19 %), or unsupported CuO (20 %). Moreover, there is a good linear relationship between the C2 H4 faradaic efficiency and CO2 uptake capacity of the supports for CuO. The local high CO2 concentration near Cu catalysts, created by CO2 capture materials, was proposed to increase the coverage of CO intermediate, which is favorable for the coupling of two CO units in the formation of C2 H4 . This study demonstrates that pairing Cu catalysts with CO2 capture supports is a promising approach for designing highly effective CO2 reduction electrocatalysts.