Forcefully engaging rods into tulips with gap discrepancy leading to pedicle screw loosening-a biomechanical analysis using long porcine spine segments.

BACKGROUND CONTEXT: Long-segment pedicle screw instrumentation is widely used to treat complex spinal disorders. Rods are routinely precontoured to maximize assistance on the correcting side of the deformity, but there often exists a residual gap discrepancy between the precontoured rods and screw tulips. No previous research has investigated the diminished pullout strength of the most proximal or distal pedicle screw resulting from a mismatched rod in long-segment pedicle screw instrumentation. PURPOSE: The present study aimed to investigate the decreased pullout force of pedicle screws affected by the gap discrepancy when forcefully engaging a mismatched rod into a tulip in a normal-density porcine spine. STUDY DESIGN: The pedicle screw fixation strength under axial pullout force was compared among three different gap discrepancies between rods and tulips using long porcine spine segments. METHODS: Twelve porcine lumbar vertebrae (L3-L6) were implanted with pedicle screws and rods. Screws on one side had no gap between the tulip and rod (0-mm group), while the most proximal screw on the other side had an intentional gap of 3 mm (3-mm group) or 6 mm (6-mm group). Three hours after forcefully engaging the rod into the tulips at room temperature, the set screws in all specimens were loosened, and each specimen was dissected into individual vertebrae for subsequent pullout testing. RESULTS: The control group exhibited significantly greater pullout strength (1987.68 ± 126.80 N) than the groups from different rod-tulip configurations (p<.05), with significantly greater strength in the 3-mm group (945.62 ± 97.43 N) than the 6-mm group (655.30 ± 194.49 N) (p<.05). Only 47.6% and 33.0% of the pullout strength was retained in the 3-mm and 6-mm groups, respectively, compared to the control group. CONCLUSIONS: Gap discrepancies between rods and tulips can significantly reduce pedicle screw pullout strength, with a correlation between decreased strength and increased gaps. Surgeons should avoid forcefully engaging mismatched rods and consider well-fitted contoured rods in spinal surgery to minimize the risk of screw loosening. CLINICAL SIGNIFICANCE: The gap discrepancy between rod and tulip significantly affected pullout strength, with greater gaps leading to reduced strength. Forcefully engaging mismatched rods into tulips in degenerative spinal surgery should be avoided to minimize the risk of early screw pullout.

Influence of various pilot hole profiles on pedicle screw fixation strength in minimally invasive and traditional spinal surgery: a comparative biomechanical study.

Despite advancements in pedicle screw design and surgical techniques, the standard steps for inserting pedicle screws still need to follow a set of fixed procedures. The first step, known as establishing a pilot hole, also referred to as a pre-drilled hole, is crucial for ensuring screw insertion accuracy. In different surgical approaches, such as minimally invasive or traditional surgery, the method of creating pilot holes varies, resulting in different pilot hole profiles, including variations in size and shape. The aim of this study is to evaluate the biomechanical properties of different pilot hole profiles corresponding to various surgical approaches. Commercially available synthetic L4 vertebrae with a density of 0.16 g/cc were utilized as substitutes for human bone. Four different pilot hole profiles were created using a 3.0 mm cylindrical bone biopsy needle, 3.6 mm cylindrical drill, 3.2-5.0 mm conical drill, and 3.2-5.0 mm conical curette for simulating various minimally invasive and traditional spinal surgeries. Two frequently employed screw shapes, namely, cylindrical and conical, were selected. Following specimen preparation, screw pullout tests were performed using a material test machine, and statistical analysis was applied to compare the mean maximal pullout strength of each configuration. Conical and cylindrical screws in these four pilot hole configurations showed similar trends, with the mean maximal pullout strength ranking from high to low as follows: 3.0 mm cylindrical biopsy needle, 3.6 mm cylindrical drill bit, 3.2-5.0 mm conical curette, and 3.2-5.0 mm conical drill bit. Conical screws generally exhibited a greater mean maximal pullout strength than cylindrical screws in three of the four different pilot hole configurations. In the groups with conical pilot holes, created with a 3.2-5.0 mm drill bit and 3.2-5.0 mm curette, both conical screws exhibited a greater mean maximal pullout strength than did cylindrical screws. The strength of this study lies in its comprehensive comparison of the impact of various pilot hole profiles commonly used in clinical procedures on screw fixation stability, a topic rarely reported in the literature. Our results demonstrated that pilot holes created for minimally invasive surgery using image-guided techniques exhibit superior pullout strength compared to those utilized in traditional surgery. Therefore, we recommend prioritizing minimally invasive surgery when screw implantation is anticipated to be difficult or there is a specific need for stronger screw fixation. When opting for traditional surgery, image-guided methods may help establish smaller pilot holes and increase screw fixation strength.

Predicting pullout strength of pedicle screws in broken bones from X-ray images.

Pedicle screw fixation is one of the most common procedures used in spinal fusion surgery. The screw loosening is a major concern, which may be caused by broken pedicles. In vitro pullout tests or insertion torque are the main approaches for assessing the stability of the screw; however, direct evidence was lacking for clinical human spines. Here, we aim to provide a model that can predict the pullout strengths of pedicle screws in various pedicle conditions from X-ray images. A weighted embedded bone volume (EBV) model is proposed for pullout strengths prediction by considering the bone heterogeneity and confinement of the screw. We showed that the pullout strength is proportional to the EBV for homogeneous bone and the weighted EBV for layered composite bone. The proposed weighted EBV model is validated with in vitro Sawbones® pullout experiments. The results show that the model has better accuracy than the simple EBV model, with a coefficient of determination of 0.94. The proposed weighted EBV model can help assess the stability of a pedicle screw in a broken pedicle by simply examining 2D X-ray images.

Improved fixation stability for repairing pedicle screw loosening using a modified cement filling technique in porcine vertebrae.

Polymethylmethacrylate (PMMA) has been applied clinically and biomechanically repair loose pedicle screws. Controversies have arisen over data due to uncontrolled cement properties, various locations and sizes of fenestrated holes in repair screws, irregular holes and different bone densities of specimens. In this study, the pullout strength was compared for two techniques, the modified technique to use PMMA to augment a threaded hole and the traditional technique with retrograde injection of a PMMA filling, for standard loose screws in porcine vertebrae. Both techniques provided statistically significant results for sufficiently randomized specimens and experimental procedures. The difference in the pullout strength between conical and cylindrical screws for the aforementioned cement augmentation techniques was also investigated. Twenty-four single-level fresh-frozen lumbar vertebrae from L1 to L6 were harvested from four mature pigs. A total of 0.8 ml of PMMA was retrograde injected into screw holes with a 5.5 mm diameter, followed by insertion of a 5.0 mm diameter repair screw in the traditional group (n = 12). A stiff threaded PMMA hole was created with a 4.5 mm tapping screw before insertion of repair screws in the modified group (n = 12). Two screw geometries were randomly assigned as cylindrical (n = 6) and conical (n = 6) in each group. The correlations between filling techniques, screw geometries and axial pullout strength were analyzed. An appropriate screw trajectory and insertion depth were confirmed using X-ray imaging prior to pullout testing in both groups. For a given screw geometry (cylindrical or conical), the pullout force of the modified group was significantly higher than that of the traditional group. There was no significant difference in the pullout force between the screw geometries for a given filling technique. The cement augmentation technique is far more influential than the screw outer geometry. The modified PMMA technique created a greater anchor force than the traditional method and could be an alternative for revision of pedicle screw loosening.

Effects of Strontium Ranelate on Spinal Interbody Fusion Surgery in an Osteoporotic Rat Model.

Osteoporosis is a bone disease that afflicts millions of people around the world, and a variety of spinal integrity issues, such as degenerative spinal stenosis and spondylolisthesis, are frequently concomitant with osteoporosis and are sometimes treated with spinal interbody fusion surgery. Previous studies have demonstrated the efficacy of strontium ranelate (SrR) treatment of osteoporosis in improving bone strength, promoting bone remodeling, and reducing the risk of fractures, but its effects on interbody fusion surgery have not been adequately investigated. SrR-treated rats subjected to interbody fusion surgery exhibited significantly higher lumbar vertebral bone mineral density after 12 weeks of treatment than rats subjected to the same surgery but not treated with SrR. Furthermore, histological and radiographic assessments showed that a greater amount of newly formed bone tissue was present and that better fusion union occurred in the SrR-treated rats than in the untreated rats. Taken together, these results show significant differences in bone mineral density, PINP level, histological score, SrR content and mechanical testing, which demonstrate a relatively moderate effect of SrR treatment on bone strength and remodeling in the specific context of recovery after an interbody fusion surgery, and suggest the potential of SrR treatment as an effective adjunct to spinal interbody fusion surgery for human patients.

Elution and Mechanical Strength of Vancomycin-Loaded Bone Cement: In Vitro Study of the Influence of Brand Combination.

Antibiotic-loaded bone cement (ALBC) is widely used in orthopaedic surgery for both prevention and treatment of infection. Little is known about the effect of different brand combinations of antibiotic and bone cement on the elution profile and mechanical strength of ALBC. Standardized specimens that consisted of one of the 4 brands of bone cement and one of the 3 brands of vancomycin were fashioned, producing 12 combinations of ALBC. Two dosages of vancomycin in 40g bone cement were used to represent the high (4g vancomycin) and low (1g vancomycin) dose groups. Concentrations of vancomycin elution from ALBC was measured for up to 336 hours. The ultimate compression strength was tested at axial compression using a material testing machine before and after elution. In both high-dose and low-dose groups, Lyo-Vancin in PALACOS bone cement resulted in the highest cumulative elution and Vanco in Simplex P bone cement resulted in the lowest elution (458% and 65% higher in high- and low-dose groups, respectively). The mechanical strength was not significantly compromised in all groups with low dose vancomycin (range: 70.31 ± 2.74 MPa to 87.28 ± 8.26MPa after elution). However, with the addition of high dose vancomycin, there was a mixed amount of reduction in the ultimate compression strength after cement aging, ranging from 5% (Vanco in Simplex P, 81.10 ± 0.48 MPa after elution) to 38% (Sterile vancomycin in CMW, 60.94 ± 5.74 MPa after elution). We concluded that the selection of brands of vancomycin and bone cement has a great impact on the release efficacy and mechanical strength of ALBC.

Modified fixations for distal femur fractures following total knee arthroplasty: a biomechanical and clinical relevance study.

PURPOSE: Distal femur fractures adjacent to total knee arthroplasty are a rare yet complex problem. Recently, extramedullary locking plate and retrograde intramedullary nail fixations have become popular options, but the complication rates associated with these procedures are 15-20 %. Modified fixations were assessed in an effort to reduce complications from unstable periprosthetic fractures. METHODS: Using experimental and finite element methods, this study compared the construct behaviours of a locking plate, a retrograde intramedullary nail, and their modifications (a spiral-blade supplemented in an intramedullary nail or a locking plate/allograft hybrid) when subjected to various fracture types, locations, loading conditions, and bony strength. The implanted models were used to assess construct stiffness, fracture micromotion, and implant stress under different osteoporotic conditions. Finally, we collected 40 cases for radiological analysis to indicate the appropriate procedure for treating periprosthetic fractures following total knee arthroplasty. RESULTS: Regardless of the fracture type, femoral constructs fixed with a conventional or spiral-blade supplemented intramedullary nail exhibited higher axial but lower torsional stiffness than those fixed with a locking plate. Torsional deformation occurred if the lower-positioned fracture had no medial support. The locking plate/allograft construct exhibited the highest stiffness and the least micromotion. A review of 40 clinical cases confirmed the above findings regarding the locking plate/allograft construct. CONCLUSION: The spiral-blade supplement of retrograde intramedullary nail and locking plate/allograft modified constructs significantly stabilizes the unstable fractured gaps. The locking plate/allograft is recommended for the periprosthetic fractures with deficient bone stock and severe osteoporosis to improve alignment and healing potentials.

Preliminary biomechanical study of different acetabular reinforcement devices for acetabular reconstruction.

BACKGROUND: Acetabular reinforcement devices (ARDs) are frequently used as load-sharing devices to allow allograft incorporation in revision hip arthroplasty with massive acetabular bone loss. The key to a successful reconstruction is robust fixation of the device to the host acetabulum. Interlocking fixation is expected to improve the initial stability of the postoperative construct. However, all commercially available ARDs are designed with non-locking fixation. This study investigates the efficacy of standard ARDs modified with locking screw mechanisms for improving stability in acetabular reconstruction. METHODS: Three types of ARDs were examined to evaluate the postoperative compression and angular stability: i) standard commercial ARDs, ii) standard ARDs modified with monoaxial and iii) standard ARDs modified with polyaxial locking screw mechanisms. All ARDs were implanted into osteomized synthetic pelvis with pelvic discontinuity. Axial compression and torsion tests were then performed using a servohydraulic material testing machine that measured load (angle) versus displacement (torque). Initial stability was compared among the groups. RESULTS: Equipping ARDs with interlocking mechanisms effectively improved the initial stability at the device/bone interface compared to standard non-locked ARDs. In both compression and torsion experiments, the monoaxial interlocking construct demonstrated the highest construct stiffness (672.6 ± 84.1 N/mm in compression and 13.3 ± 1.0 N · m/degree in torsion), whereas the non-locked construct had the lowest construct stiffness (381.4 ± 117.2 N/mm in compression and 6.9 ± 2.1 N · m/degree in torsion) (P < 0.05). CONCLUSIONS: Our study demonstrates the potential benefit of adding a locking mechanism to an ARD. Polyaxial ARDs provide the surgeon with more flexibility in placing the screws at the cost of reduced mechanical performance. This in vitro study provides a preliminary evaluation of biomechanical performance for ARDs with or without interlocking mechanisms, actual clinical trial deserves to be further investigated in future studies.

Effect of lag-screw positions on modes of fixation failure in elderly patients with unstable intertrochanteric fractures of the femur.

PURPOSE: To investigate the effect of lag-screw positions in the femoral head on modes of fixation failure. METHODS: 591 patients aged 65 years or older underwent sliding compression screw fixation for type A(1) (n=249) and type A(2) (n=342) intertrochanteric fractures of the femur after low-energy injuries. There were 18 cases of fixation failure; in 13 (group 1) the lag screw was placed in the central-central area, and in 5 (group 2) in the inferior 1/3-central area. Clinical variables of the 2 groups were compared. RESULTS: All 18 cases of fixation failure were actually type A(23) and misinterpreted as type A(22) fractures. In 13 cases, failure was attributable to cut-out of the lag screws at the superolateral edge of the femoral head. In 3 cases, failure was attributable to telescoping and more than 2 cm shortening of the femur. In one case, failure was due to penetration of the lag screw into the acetabulum. In another case, failure was due to plate loosening with breakage of cortical screws. In the 13 cases with cut-out of the lag screw (group 1), the lag screw was placed in the central-central area (p<0.001). In the remaining 5 cases with no cut-out (group 2), the lag screw was placed in the inferior 1/3-central area (p<0.01). Complications occurred significantly earlier in group 1 than in group 2 patients (2.6 vs. 4.6 months, p=0.02). The tip-apex distance was significantly shorter in group 1 than in group 2 patients (19 vs. 30 mm, p<0.001). CONCLUSION: Misinterpretation of type A(23) fractures as type A(22) may lead to fixation failure. Operative treatment should not be delayed once complications occur. The positions of the lag screw may affect the mode of fixation failure.

The healing of critical-sized femoral segmental bone defects in rabbits using baculovirus-engineered mesenchymal stem cells.

Management of massive segmental bone defects remains a challenging clinical problem and bone marrow-derived mesenchymal stem cells (BMSCs) hold promise for bone regeneration. To explore whether BMSCs engineered by baculovirus (an emerging gene delivery vector) can heal large bone defects, New Zealand White (NZW) rabbit BMSCs were transduced with the BMP2-expressing baculovirus or VEGF-expressing baculovirus, and co-implanted into critical-sized (10mm) femoral segmental defects in NZW rabbits. X-ray analysis revealed that the baculovirus-engineered BMSCs not only bridged the defects at as early as week 2, but also healed the defects in 100% of rabbits (13/13) at week 4. The osteogenic metabolism, as monitored by positron emission tomography (PET) also suggested the completion of bone healing at week 8. When compared with other control groups, the BMP2/VEGF-expressing BMSCs remarkably enhanced the segmental bone repair and mechanical properties, as evidenced by micro-computed tomography (microCT), histochemical staining and biomechanical testing. The ameliorated bone healing concurred with the augmented angiogenesis. These data demonstrated, that BMSCs engineered to express BMP2 and VEGF accelerate the repair of large femoral bone defects and improve the quality of the regenerated bone, which paves an avenue to utilizing baculovirus as a vector for BMSCs modification and regenerative medicine.

Repair of large cranial defects by hBMP-2 expressing bone marrow stromal cells: comparison between alginate and collagen type I systems.

Despite a wide range of available sources for bone repair, significant limitations persist. To bioengineer bone, we have previously transferred adenovirus-mediated human BMP-2 gene into autologous bone marrow stromal cells (MSC). We have successfully repaired large, full thickness, cranial defects using this approach. We report now the effectiveness of various hydrogels as the scaffold for this type of bone regeneration, comparing specifically alginate with Type I collagen. Cultured MSC of miniature swine were infected with BMP-2 or beta-gal adenovirus 7 days before implantation. These cells were mixed with alginate, ultrapure alginate, alginate-RGD, or type I collagen to fabricate the MSC/biomaterial constructs. The results of cranial bone regeneration were assessed by gross examination, histology, 3D CT, and biomechanical tests at 6 weeks and 3 months after implantation. We found that the BMP-2 MSC/collagen type I construct, but not the beta-gal control, effectively achieved nearly complete repair of the cranial defects. No bone regeneration was observed with the other hydrogels. Biomechanical testing showed that the new bone strength was very close and only slightly inferior to that of normal cranial bone. Controlling for the integration of stem cells and ex vivo gene transfer, the alginate scaffolds has a significant negative impact on the success of the construct. Our study demonstrates better bone regeneration by collagen type I over alginate. This may have therapeutic implications for tissue engineered bone repair.

Biomechanical optimization of different fixation modes for a proximal femoral L-osteotomy.

BACKGROUND: Numerous proposed surgical techniques have had minimal success in managing greater trochanter overgrowth secondary to retarded growth of the femoral capital epiphysis. For reconstruction of residual hip deformities, a novel type of proximal femur L-osteotomy was performed with satisfactory results. Although the clinical outcome was good, the biomechanical characteristics of the femur after such an osteotomy have not been clearly elucidated. Therefore, this study presents a three dimensional finite element analysis designed to understand the mechanical characteristics of the femur after the L-osteotomy. METHODS: A patient with left hip dysplasia was recruited as the study model for L-osteotomy. The normal right hip was used as a reference for performing the corrective surgery. Four FEA models were constructed using different numbers of fixation screws but the same osteotomy lengths together with four FEA models with the same number of fixation screws but different osteotomy lengths. The von Mises stress distributions and femoral head displacements were analyzed and compared. RESULTS: The results revealed the following: 1). The fixation devices (plate and screws) sustained most of the external loading, and the peak value of von Mises stress on the fixation screws decreased with an increasing number of screws. 2). Additional screws are more beneficial on the proximal segment than on the distal segment for improving the stability of the postoperative femur. 3). The extent of osteotomy should be limited because local stress might be concentrated in the femoral neck region with increasing length of the L-osteotomy. CONCLUSION: Additional screw placement on the proximal segment improves stability in the postoperative femur. The cobra-type plate with additional screw holes in the proximal area might improve the effectiveness of L-osteotomies.

Bone marrow mesenchymal stem cells form ectopic woven bone in vivo through endochondral bone formation.

Autologous vascularized bone grafts, allografts, and biocompatible artificial bone substitutes each have their shortcomings. Bones regenerated using recombinant human bone morphogenetic proteins, demineralized bone powder, or combinations of these are generally small and do not meet the need. The current trend is to use tissue engineering approaches with bone marrow mesenchymal stem cells (MSCs) to generate bones of a desired size and shape. A suspension of osteogenically induced MSCs (CD11a-, CD29+, CD44+) was added to 2% alginate, gelled by mixing this combination with calcium sulfate (CaSO(4) 0.2 g/mL), and injected into the subcutaneous pocket in the dorsal aspect of nude mice. Cells of various concentrations (0, 10, 50, and 70 million/mL) were used. These implanted constructs were harvested at predetermined times up to 30 weeks for histology. The doubling time of bovine MSCs is 3.75 +/- 1.96 days and the proliferation is rapid. Histological evaluation revealed signs of endochondrosis with woven bone deposition. The equilibrium modulus increased with time in vivo, though less than that of normal tissue. Implants seeded with 70 million cells/mL for 6 months resulted in the best formation of equilibrium modulus. This approach has several advantages: (i) obtaining MSCs is associated with low donor morbidity; (ii) MSCs proliferate rapidly in vitro, and a large number of viable cells can be obtained; and (iii) the MSC/alginate constructs can develop into bone-like nodules with high cell viability. Such a system may be useful in large-scale production of bony implants or in the repair of bony defects. The fact that endochondral bone formation led to woven bone suggests its potential feasibility in regional cell therapy.

Liquid gentamicin in bone cement spacers: in vivo antibiotic release and systemic safety in two-stage revision of infected hip arthroplasty.

BACKGROUND: Powdered antibiotics are widely used in acrylic bone cement. Liquid antibiotics, however, have rarely been employed. This study investigated the application of liquid gentamicin, a much less costly antibiotic with a broad antimicrobial spectrum, in bone cement to treat musculoskeletal infections. METHODS: Forty-two patients undergoing two-stage revision hip arthroplasty for periprosthetic infection were managed with an interim cement spacer loaded with liquid gentamicin (480 mg per 20 mL pack of cement monomer) with or without vancomycin (3.0 g per 40 g pack cement polymer). Serum and aliquots of drainage collected after the first-stage surgery; joint fluid obtained at the time of the second-stage surgery were analyzed for antibiotic concentrations and bioactivity. Antibiotic levels in the peripheral blood and renal function were also monitored. RESULTS: Antibiotic levels in joint fluid peaked on the first day after implantation of the spacer and then gradually declined during the first week, with levels of gentamicin and vancomycin reached 43.6 mg/L +/- 12.3 mg/L and 485.5 mg/L +/- 103.5 mg/L, respectively. Bioassay confirmed the antimicrobial activity of the released antibiotics. The systemic antibiotic concentrations were below detectable levels in the majority of patients, and no nephrotoxicity was noted. At a mean 87 days after implantation, antibiotic concentrations in joint fluid remained clinically effective (gentamicin, 5.1 mg/L +/- 2.2 mg/L and vancomycin, 21.6 mg/L +/- 8.5 mg/L). CONCLUSIONS: Incorporation of liquid gentamicin in bone cement spacers led to effective drug delivery with systemic safety. Substantial health care dollars could be saved by the use of liquid gentamicin in bone cement to treat musculoskeletal infections.

Biomechanical comparison of lumbar spine instability between laminectomy and bilateral laminotomy for spinal stenosis syndrome - an experimental study in porcine model.

BACKGROUND: The association of lumbar spine instability between laminectomy and laminotomy has been clinically studied, but the corresponding in vitro biomechanical studies have not been reported. We investigated the hypothesis that the integrity of the posterior complex (spinous process-interspinous ligament-spinous process) plays an important role on the postoperative spinal stability in decompressive surgery. METHODS: Eight porcine lumbar spine specimens were studied. Each specimen was tested intact and after two decompression procedures. All posterior components were preserved in Group A (Intact). In Group B (Bilateral laminotomy), the inferior margin of L4 lamina and superior margin of L5 lamina were removed, but the L4-L5 supraspinous ligament was preserved. Fenestrations were made on both sides. In Group C (Laminectomy) the lamina and spinous processes of lower L4 and upper L5 were removed. Ligamentum flavum and supraspinous ligament of L4-L5 were removed. A hydraulic testing machine was used to generate an increasing moment up to 8400 N-mm in flexion and extension. Intervertebral displacement at decompressive level L4-L5 was measured by extensometer RESULTS: The results indicated that, under extension motion, intervertebral displacement between the specimen in intact form and at two different decompression levels did not significantly differ (P > 0.05). However, under flexion motion, intervertebral displacement of the laminectomy specimens at decompression level L4-L5 was statistically greater than in intact or bilateral laminotomy specimens (P = 0.0000963 and P = 0.000418, respectively). No difference was found between intact and bilateral laminotomy groups. (P > 0.05). CONCLUSION: We concluded that a lumbar spine with posterior complex integrity is less likely to develop segment instability than a lumbar spine with a destroyed anchoring point for supraspinous ligament.

Thermal damage potential during hip resurfacing in osteonecrosis of the femoral head: an experimental study.

Hip resurfacing arthroplasty has become an attractive treatment option for young, active patients with femoral head necrosis. However, little information is available about the potential thermal damage to the remaining femoral head when a cemented component is used. We used an experimental model to measure the temperature profile at the cement-bone interface during hip resurfacing. We compared four simulated lesion sizes-15, 25, 33, and 50%-of the femoral head, and a control group with no cystic lesion. Temperatures were measured with the specimens in a 37 degrees C saline bath or with copious pulsed lavage. With specimens tested in the bath, peak temperatures were higher, and durations of temperatures above 50 degrees C were longer, in femoral heads with necrotic lesions (88.8 +/- 7.5 degrees C; 17.6 +/- 1.1 min for a 15% lesion; 96.2 +/- 7.2 degrees C; 22.86 +/- 1.3 min for a 25% lesion; 99.7 (c) 200 +/- 9.4 degrees C; 28.6 +/- 2.0 min for a 33% lesion; and 97.2 +/- 4.2 degrees C; 35.6 +/- 2.4 min for a 50% lesion) than those in the control group (65.8 +/- 4.9 degrees C; 10.0 +/- 1.3 min). The larger the cement-filled cysts, the longer the temperatures remained above 50 degrees C. Although copious lavage reduced the temperature profile in each group, the temperatures remained above 50 degrees C for 7 to 17 min in specimens with necrotic cysts. The measured temperatures during surface replacement are sufficiently high in magnitude and long in duration to cause thermal damage to the remaining bone in femoral heads with preexisting necrotic lesions. Hip resurfacing for femoral head necrosis should be performed with caution.

Plating treatment for tibial plateau fractures: a biomechanical comparison of buttress and tension band positions.

INTRODUCTION: The load tolerance of conventional plate treatment for bicondylar tibial plateau fractures with the buttress and the tension band positions was compared from biomechanical viewpoints. MATERIALS AND METHODS: Fourteen left synthetic tibiae divided into two groups were tested. T-plates in the buttress group were placed on the medial tibial subcondyle and T-plates in the tension band group were placed on the lateral tibial subcondyle. All specimens were evaluated with a Material Testing System (MTS) machine. A linear variance displacement transducer gauge was placed on the medial tibial subcondyle. The anatomic axis of the synthetic femur and the tibia was maintained at 6 degrees varus in the frontal plane. The MTS actuator was set to increase displacement at 3 mm/min. All specimens were evaluated to failure. The relative motion and the ultimate failure load (UFL) between both groups were compared. RESULTS: The buttress group had significantly less displacement than the tension band group following the incrementally increased loading (p < 0.001). At failure, the buttress group also had a higher UFL (p < 0.001) and less displacement (p = 0.009) than the tension band group. CONCLUSION: All medial tibial condylar fragments achieved improved stabilization from the medial aspect of the proximal tibia by conventional plates. When conventional plates cannot be placed medially due to skin ailments, lateral placement of conventional plates may have the insufficient stability. Protected weight bearing should be followed strictly.

The effect of necrotic lesion size and rotational degree on the stress reduction in transtrochanteric rotational osteotomy for femoral head osteonecrosis--a three-dimensional finite-element simulation.

BACKGROUND: The prospect for success in the efficacy of osteotomy for precollapse stage of femoral head osteonecrosis depends on the ability to predict reliably the stress changes derived from specific osteotomies. A three-dimensional finite-element analysis was thus designed to compute necrotic femoral head stress changes with different extent of necrocrosis that accompany anterior or posterior rotational osteotomies. METHOD: Computed tomography images of a standard composite femur were used to create the three-dimensional finite-element intact femur model. Based on the intact model, 27 models simulating three different levels of necrotic region together with nine different rotational osteotomies were created. The von Mises stress distributions of each model were analyzed and compared for a loading condition simulating single-legged stance. FINDINGS: (1) The stress reduction in anterior rotational osteotomy is more effective as compared to that of the posterior rotational osteotomy for various necrotic lesion sizes. (2) Von Mises stress on the necrotic zone decreased with increasing rotational angle. The decreasing rate was higher for the femoral head with a narrow lesion. (3) Femoral head with a wider necrotic lesion had a higher risk for developing collapse due to high local stress on the surface of necrotic region; whereas the necrotic region tended to expand in size instead of collapse for femoral head with a narrow lesion due to high local stress on the interface between necrotic region and healthy bone. INTERPRETATION: Transtrochanteric rotational osteotomy is a technically demanding procedure and associated with high complication risks, a more scrupulous planning including the finite-element analysis should be considered before doing surgery in clinical subjects.

Early administration of hyperbaric oxygen therapy in distraction osteogenesis--a quantitative study in New Zealand rabbits.

BACKGROUND: We investigated the effect of hyperbaric oxygen (HBO) therapy on the early phase of tibial lengthening in our established rabbit model. METHODS: Twenty-four male rabbits (six per group) underwent right tibial lengthening by 5 mm. Group 1 then underwent 2.5 atmospheres of absolute hyperbaric oxygenation for 2 hours daily for 6 weeks postoperatively; group 2, for early 5 weeks (weeks 1-5), group 3, for late 5 weeks (weeks 2-6), and group 4 had no HBO therapy. Bone mineral density (BMD) was measured before surgery and weekly thereafter from weeks 2 through 6. The mechanical strengths of the lengthened tibias were measured. RESULTS: Significantly higher mean %BMDs were obtained for groups 1 and 2 compared with groups 3 and 4. There was no difference in the mean %BMD between groups 1 and 2 (p > 0.05). The results were similar for mean percentage maximal torque; group 1 had the maximum torque, followed sequentially by groups 2 though 4. CONCLUSION: The study results suggest that early and full-term administration of HBO therapy on tibial lengthening may achieve better benefits.

The degrees to which transtrochanteric rotational osteotomy moves the region of osteonecrotic femoral head out of the weight-bearing area as evaluated by computer simulation.

BACKGROUND: Transtrochanteric rotational osteotomy is a technical demanding procedure. Currently, the pre-operative planning of the transtrochanteric rotational osteotomy is mostly based on X-ray images. The surgeons would need to reconstruct the three-dimensional structure of the femoral head and the necrosis in their mind. This study develops a simulation platform using computer models based on the computed tomography images of the femoral head to evaluate the degree to which transtrochanteric rotational osteotomy moves the region of osteonecrotic femoral head out of the weight-bearing area in stance and gait cycle conditions. Based on this simulation procedure, the surgeons would be better informed before the surgery and the indication can be carefully assessed. METHOD: A case with osteonecrosis involving 15% of the femoral head was recruited. Virtual models with the same size lesion but at different locations were devised. Computer models were created using SolidWorks 2000 CAD software. The area ratio of weight-bearing zone occupied by the necrotic lesion on two conditions, stance and gait cycle, were measured after surgery simulations. FINDINGS: For the specific case and virtual models devised in this study, computer simulation showed the following two findings: (1) The degrees needed to move the necrosis out of the weight-bearing zone in stance were less by anterior rotational osteotomy as compared to that of posterior rotational osteotomy. However, the necrotic region would still overlap with the weight-bearing area during gait cycle. (2) Because the degrees allowed for posterior rotation were less restricted than anterior rotation, posterior rotational osteotomies were often more effective to move the necrotic region out of the weight-bearing area during gait cycle. INTERPRETATION: The computer simulation platform by registering actual CT images is a useful tool to assess the direction and degrees needed for transtrochanteric rotational osteotomy. Although the results indicated that anterior rotational osteotomy was more effective to move the necrosis out of the weight-bearing zone in stance for models devised in this study, in circumstances where the necrotic region located at various locale, considering the limitation of anterior rotation inherited with the risk of vascular compromise, it might be more beneficial to perform posterior rotation osteotomy in taking account of gait cycle.