Hydrophilic interaction chromatography-type sorbent prepared by the modification of methacrylate-base resin with polyethyleneimine for solid-phase extraction of polar compounds.

Hydrophilic interaction chromatography (HILIC)-type sorbents were newly developed for the solid-phase extraction (SPE) of polar compounds. Two methacrylate-base resins with different cross-linking monomers and pore properties were synthesized, and three polyethyleneimines (PEIs) with different molecular weights were modified onto each base resin. In both cases, PEIs with a molecular weight of 10,000 (PEI-10,000) exhibited the highest adsorption properties for polar compounds (uracil, uridine, adenosine, cytidine, and guanosine). To control the water-enriched layer at the surface of the PEI-10,000-modified sorbents, the additive amount of PEI-10,000 in the modified reaction was also optimized. When 10 times the amount of PEI-10,000 to each base resin was added, an improvement in adsorption property was observed. Moreover, the use of a nonaqueous sample solution (100% acetonitrile) during the sample loading process drastically improved adsorption, especially for uracil (about 80%) and adenosine (100%). These results indicate that the formation of a strong water-enriched layer at the surface of sorbents with an effective expression of hydrophilic interaction was an important factor in the adsorption properties of polar compounds in HILIC mode-SPE.

Dual determination of nitrite and iron by a single greener sequential injection spectrophotometric system employing a simple single aqueous extract from Areca catechu Linn. serving as a natural reagent.

Dual determination of nitrite and iron was proposed by using a single greener sequential injection (SI) spectrophotometric system employing a simple single aqueous extract from Areca catechu Linn. The extract served as a natural reagent to replace N-(1-naphthyl)ethylenediamine (NED) of the Griess reagent with nitrite and 1,10-phenanthroline with iron. The color products possessed analytical wavelengths at 430 and 560 nm, respectively. Conditions for the SI procedure were optimized using a univariate experimental design. Calibration ranges were up to 5.0 mg L-1 and 10.0 mg L-1 with limits of detection (LODs) of 0.04 mg L-1 and 0.05 mg L-1 for nitrite and iron(iii), respectively, and relative standard deviations (RSDs) being less than 3%. Recoveries of spiked standard nitrite and iron(iii) at 0.3 mg L-1 and 0.5 mg L-1 in water samples were 88 to 104% and 84 to 109%, respectively. The developed method successfully achieved dual determination of nitrite and total iron agreeing at a 95% confidence level with the reference methods of the conventional Griess assay and flame atomic absorption spectrometry (FAAS), respectively. The proposed method utilized locally available material from plants and serves the UN-SDGs.

Evaluation of the adsorption properties of nucleobase-modified sorbents for a solid-phase extraction of water-soluble compounds.

We developed hydrophilic interaction chromatography (HILIC)-type sorbents modified with nucleobases for solid phase extraction (SPE). The synthesized hydrophilic base resins were modified by each nucleobase (adenine, guanine, and cytosine). The measurement of the amount of water content indicated that each nucleobase-modified sorbent had a water layer. To evaluate the adsorption properties in the HILIC mode, we chose two nucleobases (uracil and adenine) and four nucleosides (uridine, adenosine, cytidine, guanosine) as water-soluble analytes, which were loaded into an SPE cartridge packed with the nucleobase-modified sorbent. Firstly, 95% acetonitrile (ACN) solutions were used in the process of conditioning and sample loading of the above polar analytes. High recoveries of the analytes were observed in each nucleobase-modified sorbent, and the Diol-type sorbent (no modification with any of the nucleobases) did not adsorb each water-soluble analyte. On the basis of this result, a 98% ACN solution was used during the process of conditioning and sample loading to decrease the concentration of water in the sample, which potentially inhibited the formation of hydrogen bonding between each analyte and the modified nucleobase. Considerable improvements of recoveries were observed in Adenine- and Cytosine-modified sorbents. These results were possibly attributed to the effective expression of hydrogen bonding by decreasing water concentration in the sample solution. Although a non-aqueous (100% ACN) sample solution can be expected to obtain higher recoveries compared with the 98% ACN solution, a decrease in recoveries was observed in Adenine-modified sorbent. From these results, the highest adsorption property was observed in Adenine-modified sorbent using 98% ACN as a sample condition, and the combination of this sample condition and sorbent is effective for high adsorption under HILIC condition. Moreover, we also revealed that a balance between the thickness of water layer and the modification amount of nucleobase is important for retention in the HILIC-type sorbent.

Preparation of Cyclic-1,N2-propano-2'-deoxyguanosine-d7 as an Internal Standard for ESI-MS/MS Determination of DNA Damage from Acetaldehyde.

Cyclic-1,N2-propano-2'-deoxyguanosine-d7 (CPr-dG-d7) was prepared as an isotopic internal standard (IS) for electrospray ionization tandem mass spectrometry (ESI-MS/MS) quantification of CPr-dG in DNA as a candidate cancer risk marker of acetaldehyde intake, mainly from drinking. The deuterated compound was reasonably synthesized from acetaldehyde-d4 and 2'-deoxyguanosine in deuterium oxide (D2O), preventing the deuterium atoms of acetaldehyde-d4 from being substituted by hydrogen atoms, which occurred seriously in aqueous synthesis media via keto-enol tautomerism. Furthermore, another deuterium atom was added from D2O to form CPr-dG-d7. After four weeks of storage in H2O at 10°C, CPr-dG-d7 was found to be sufficiently stable for practical use. The calibration curve of CPr-dG by using a hydrophilic interaction chromatography-ESI-MS/MS system with CPr-dG-d7 as the IS showed sufficient linearity from 1.0 × 10-10 to 4.0 × 10-9 M with r2 = 0.998.

Optimization of background electrolyte composition for simultaneous contactless conductivity and fluorescence detection in capillary electrophoresis of biological samples.

In this article, optimization of BGE for simultaneous separation of inorganic ions, organic acids, and glutathione using dual C4 D-LIF detection in capillary electrophoresis is presented. The optimized BGE consisted of 30 mM 2-[4-(2-hydroxyethyl)piperazin-1-yl]ethanesulfonic acid, 15 mM 2-amino-2-hydroxymethyl-propane-1,3-diol, and 2 mM 18-crown-6 at pH 7.2 and allowed simultaneous separation of ten inorganic anions and cations, three organic acids and glutathione in 20 min. The samples were injected hydrodynamically from both capillary ends using the double-opposite end injection principle. Sensitive detection of anions, cations, and organic acids with micromolar LODs using C4 D and simultaneously glutathione with nanomolar LODs using LIF was achieved in a single run. The developed BGE may be useful in analyses of biological samples containing analytes with differing concentrations of several orders of magnitude that is not possible with single detection mode.

Effects of pendant-like hydrophilic monomers on the adsorption properties of reversed-phase-type sorbents for solid-phase extraction.

Solid-phase extraction (SPE) has been extensively employed as a pretreatment method. In SPE, reversed-phase-type sorbents have been widely applied for the pretreatment of environmental or biological samples. Hydrophilic-lipophilic balance (HLB)-type sorbents, constituting the copolymers used as reversed-phase-type sorbents, have been applied for various sample pretreatment methods. In HLB-type sorbents, the hydrophilic monomer contributes to the improved wettability of sorbents and increase of polar interactions. In this study, three pendant-like hydrophilic monomers, viz. N-vinylpyrrolidone (NVP), 4-acryloylmorpholine (AMO), and 4-vinyl-1,3-dioxolan-2-one (VDO), respectively, exhibiting different Log P values and possibly causing different polar interactions, were selected to improve the adsorption properties of polar compounds, and divinylbenzene (DVB)-based HLB-type sorbents containing each hydrophilic monomer were synthesized and examined. By the optimization of the molar ratio of DVB and the hydrophilic monomer (i.e. HLB), the inert diluent, and the degree of cross-linking, the developed sorbents exhibited higher recoveries for various polar compounds (viz. cytosine, uracil, cytidine, uridine, 2'-deoxycytidine, 2'-deoxyguanosine, adenine, thymidine, adenosine, and 2'-deoxyadenosine) compared to commercially available HLB-type sorbents.

Effects of hydrophilic monomers on sorptive properties of divinylbenzene-based reversed phase sorbents.

Solid phase extraction (SPE) has been extensively used as a pretreatment method. In SPE methods, commercially available reversed phase type sorbents, which consist of macroporus styrene-divinylbenzene or copolymers including divinylbenzene (DVB) and hydrophilic monomers, have been applied to a variety of samples. The later sorbents are called hydrophilic lipophilic balanced (HLB) type sorbents. Hydrophilic monomers in hydrophilic lipophilic balanced type sorbents contribute to the increase in retention of polar compounds, because hydrophilic monomers improve the wettability and increase the interaction with polar compounds as analytes. In this study, three different methacrylate monomers (ethylene glycol dimethacrylate (EGDMA), glycerol dimethacrylate (GDMA) and trimethylolpropane trimethacrylate (TMPTMA)), which are expected to improve the retention of polar compounds, were chosen, and DVB-based copolymetric sorbents including the three monomers were newly synthesized. Among them, the sorbents including GDMA or TMPTMA gave higher recoveries to polar compounds such as uridine and adenine than that including EGDMA. The optimization studies of hydrophilic lipophilic balance, inert diluent and the purity of DVB improved the sorptive abilities of the sorbents. The developed sorbents have higher recoveries for variety of polar compounds (cytosine, uracil, cytidine, uridine, 2'-deoxycytidine, 2'-deoxyguanosine, adenine, thymidine, adenosine and 2'-deoxyadenosine) than commercially available hydrophilic lipophilic balanced type sorbents, while the recoveries for theophylline were comparable between the proposed sorbents and the commercial sorbents.

Progress in a selective method for the determination of the acetaldehyde-derived DNA adducts by using HILIC-ESI-MS/MS.

Acetaldehyde (AA), which is present in tobacco smoke, automobile exhaust gases and alcohol beverage, is a mutagen and carcinogen. AA reacts with 2'-deoxyguanosine (dG) in DNA to form N2-ethyl-dG (EtdG) and cyclic, 1, N2-propano-dG (CPrdG), which are considered to have a critical role in carcinogenesis induced by AA. In this study, we have developed a highly sensitive method for the quantitation of the two AA-derived DNA adducts by using liquid chromatography-electrospray ionization-tandem mass spectrometry (LC-ESI-MS/MS) in which hydrophilic interaction chromatography (HILIC) employing mobile phases of high organic solvent concentration was selected to improve the ionization efficiency in the ESI process. Fourteen times and 11 times larger peak areas for EtdG and CPrdG, respectively, in HILIC-ESI-MS/MS were obtained compared with those in reversed phase (RP)-LC-ESI-MS/MS. Furthermore, 6.9 times (for EtdG) and 2.4 times (for CPrdG) larger peak areas were also obtained as additional enhancement by varying additive compounds in the HILIC mobile phases from ammonium acetate to ammonium bicarbonate. In total, the enhancements in detected MS signal intensities by exchanging from the RP-LC system to the HILIC system are 97 times for EtdG and 26 times for CPrdG, respectively. Three commercially available HILIC columns with different polar functional groups were examined and sufficient separation between normal 2'-deoxynucleosides and the AA-derived DNA adducts was achieved by a carbamoyl-bonded HILIC column. Finally, we applied the established method to quantify EtdG and CPrdG in the damaged calf thymus DNA.

Advanced Stopped-in-Loop Flow Analysis with a Reagents-Merging Zones Technique for a Catalytic Successive Determination of Vanadium and Iron.

An advanced stopped-in-loop flow analysis (SILFA) is proposed for the catalytic determinations of vanadium and iron. The chemistry relies on a vanadium- or iron-catalyzed oxidative reaction of p-anisidine by bromate or hydrogen peroxide in the presence of an activator (Tiron or 1,10-phenanthlorine) to form a red dye (510 nm). Reagents for the vanadium- or iron-catalyzed reaction are well mixed by a reagents-merging zones technique. A sample solution is loaded together with well-mixed reagents into a loop in the SILFA configuration, followed by spectrophotometric detection. The advanced SILFA system provides a selective method for the trace determination of vanadium and iron.

Stopped-in-loop flow analysis system for successive determination of trace vanadium and iron in drinking water using their catalytic reactions.

An automated stopped-in-loop flow analysis (SILFA) system is proposed for the successive catalytic determination of vanadium and iron. The determination of vanadium was based on the p-anisidine oxidation by potassium bromate in the presence of Tiron as an activator to form a reddish dye, which has an absorption maximum at 510 nm. The selectivity of the vanadium determination was greatly improved by adding diphosphate as a masking agent of iron. For the iron determination, an iron-catalyzed oxidative reaction of p-anisidine by hydrogen peroxide with 1,10-phenanthroline as an activator to produce a reddish dye (510 nm) was employed. The SILFA system consisted of two peristaltic pumps, two six-port injection valves, a four-port selection valve, a heater device, a spectrophotometric detector and a data acquisition device. One six-port injection valve was used for the isolation of a mixed solution of standard/sample and reagent to promote each catalytic reaction, and another six-port injection valve was used for switching the reagent for vanadium or iron to achieve selective determination of each analyte. The above mentioned four-port selection valve was used to select standard solutions or sample. These three valves and the two peristaltic pumps were controlled by a built-in programmable logic controller in a touchscreen controller. The obtained results showed that the proposed SILFA monitoring system constituted an effective approach for the selective determination of vanadium and iron. The limits of detection, 0.052 and 0.55 µg L(-1), were obtained for vanadium and iron, respectively. The proposed system was successfully applied to drinking water samples without any preconcentration procedures.

Automatic On-line Solid-phase Extraction-Electrothermal Atomic Absorption Spectrometry Exploiting Sequential Injection Analysis for Trace Vanadium, Cadmium and Lead Determination in Human Urine Samples.

A fully automated sequential injection column preconcentration method for the on-line determination of trace vanadium, cadmium and lead in urine samples was successfully developed, utilizing electrothermal atomic absorption spectrometry (ETAAS). Polyamino-polycarboxylic acid chelating resin (Nobias chelate PA-1) packed into a handmade minicolumn was used as a sorbent material. Effective on-line retention of chelate complexes of analytes was achieved at pH 6.0, while the highest elution effectiveness was observed with 1.0 mol L(-1) HNO3 in the reverse phase. Several analytical parameters, like the sample acidity, concentration and volume of the eluent as well as the loading/elution flow rates, have been studied, regarding the efficiency of the method, providing appropriate conditions for the analysis of real samples. For a 4.5 mL sample volume, the sampling frequency was 27 h(-1). The detection limits were found to be 3.0, 0.06 and 2.0 ng L(-1) for V(V), Cd(II) and Pb(II), respectively, with the relative standard deviations ranging between 1.9 - 3.7%. The accuracy of the proposed method was evaluated by analyzing a certified reference material (Seronorm(TM) trace elements urine) and spiked urine samples.

Flow injection spectrophotometric determination of formaldehyde based on its condensation with hydroxylamine and subsequent redox reaction with iron(III)-ferrozine complex.

A flow injection (FI) spectrophotometric method is proposed for the determination of low concentration of formaldehyde (HCHO) in liquid media. It is based on the condensation of HCHO with hydroxylamine sulfate, followed by the reduction reaction of iron(III)-ferrozine complex with the residual hydroxylamine to form a purple iron(II)-ferrozine complex (λ(max)=562 nm). In the first reaction, hydroxylamine decreases proportionally to the concentration of HCHO, and therefore the produced purple iron(II)-ferrozine complex decreases with increasing HCHO (a negative FI peak is obtained). The detection limit (S/N=3) was 1.6 µg L(-1). The method can be applied to the determination of HCHO in industrial wastewater.

Highly sensitive determination of cadmium and lead in leached solutions from ceramic ware by graphite furnace atomic absorption spectrometry coupled with sequential injection-based solid phase extraction method.

A fully automated pretreatment system based on sequential injection solid-phase extraction (SPE) coupled to a graphite furnace atomic absorption spectrometer (Auto-Pret-GFAAS system) was developed to determine trace amounts of cadmium and lead. A handmade minicolumn packed with a chelating resin was used for the preconcentration of both metals. All protocol for the on-line SPE method was controlled by home-made software. A trigger switch that was placed next to the graphite furnace was used to synchronize the home-made software with built-in software in the GFAAS. One milliliter of sample solution was flowed through into the minicolumn, the analytes were collected and concentrated on the solid phase, and the analytes were eluted with nitric acid (3 M), and detected by GFAAS. The limits of detection (3sigma) for cadmium and lead were 0.20 and 2.6 ng L(-1), respectively. The sample throughput was 47 h(-1) for 1 mL sample loading. The proposed sensitive method with the original Auto-Pret-GFAAS system was applied to the determination of cadmium and lead in tap water and in leached solutions from ceramic ware using 4% acetic acid.

A multiple processing hybrid flow system for analysis of formaldehyde contamination in food.

This work proposes a flow system suitable for the rapid screening of formaldehyde contaminated in food. The system is based on the concept of a flow analyzer with a Hantzsch reaction. An operating procedure was developed for multiple tasking and high sample throughput. This resulted in a significant sample throughput of 51 samples h(-1). Under the optimized conditions, linear calibration from 10 to 100 microM was obtained. The system gave a limit of detection and a limit of quantitation of 0.06 and 0.10 mg kg(-1), respectively. The system was successfully applied to re-hydrated dry squids, vegetables and mushrooms.

Sequential injection lab-on-valve simultaneous spectrophotometric determination of trace amounts of copper and iron.

A sequential injection (SI) method in a lab-on-valve (LOV) format for simultaneous spectrophotometric determination of copper and iron has been devised. The detection chemistry is based on the complex formation of 2-(5-bromo-2-pyridylazo)-5-[N-n-propyl-N-(3-sulfopropyl)amino]aniline (5-Br-PSAA) with copper(II) and/or iron(II) at pH 4.6. Copper(II) reacts with 5-Br-PSAA to form the complex which has an absorption maximum at 580 nm but iron(III) does not react. In the presence of a reducing agent only iron(II)-5-Br-PSAA complex is formed and detected at 558 nm. Under the optimum experimental conditions, the determinable ranges are 0.1-2 mg l(-1) for copper and 0.1-5 mg l(-1) for iron, respectively, with a sampling rate of 18 h(-1). The limits of detection are 50 microg l(-1) for copper and 25 microg l(-1) for iron. The relative standard deviations (n=15) are 2% for 0.5 mg l(-1) copper and 1.8% for 0.5 mg l(-1) iron when determined in standard solutions. The recoveries range between 96 and 105% when determining 0.25-2 mg l(-1) of copper and 0.2-5 mg l(-1) of iron in artificial mixtures at copper/iron ratios of 1:10 to 5:1. The proposed SI-LOV method is successfully applied to the simultaneous determination of copper and iron in multi-element standard solution and in industrial wastewater samples.

Successive determination of copper and iron by a flow injection-catalytic photometric method using a serial flow cell.

A flow injection-catalytic spectrophotometric method using a serial flow cell was proposed for the successive determination of trace amounts of copper and iron. This method is based on the oxidation coupling of p-anisidine with N,N-dimethylaniline in the presence of hydrogen peroxide to form a dye, which has an absorption maximum at 740 nm. In this indicator reaction, ligands such as 1,10-phenanthroline (phen) and diphosphate were achieved to improve the sensitivity and selectivity. Under the optimal experimental conditions, the determinable ranges were 0.05-5 ppb for copper and 0.5 - 100 ppb for iron, respectively. The RSDs (n = 10) were 0.78% for 0.5 ppb copper(II) and 0.5% for 200 ppb iron(III). The sample throughput was 30 h(-1). The present flow-injection method was applied to the determination of copper and iron in standard river water, tap water, and other natural water samples, and also to the analysis of labile and inert complexes in synthesized samples containing humic acid with copper(II) or iron(III).

Catalytic flow-injection determination of sub-ppb copper(II) using the redox reaction of cysteine with iron(III) in the presence of 2,4,6-tris(2-pyridyl)-1,3,5-triazine.

A kinetic-catalytic spectrophotometric flow-injection method was developed for the rapid and sensitive determination of trace amounts of copper(II). The method is based on the catalytic effect of copper(II) on the redox reaction of cysteine with iron(III). Iron(II) produced by the catalytic reaction reacts with 2,4,6-tris(2-pyridyl)-1,3,5-triazine (TPTZ) to form the iron(II)-TPTZ complex (lambda(max) = 593 nm). By measuring an absorbance of the complex, one could determine 0.05-8 ppb copper(II) with the relative standard deviations (n = 10) of 1.6%, 1.3%, and 0.8% for 0.5 ppb, 1 ppb, and 2 ppb copper(II), respectively. The limit of detection (S/N = 3) was 0.005 ppb. The sample throughput was 30 h(-1). The proposed method was successfully applied to the determination of copper in natural water and serum samples.

Utilization of activating and masking effects by ligands for highly selective catalytic spectrophotometric determination of copper and iron in natural waters.

A kinetic-catalytic spectrophotometric method is proposed for the successive determination of nanogram levels of copper and iron, which is based on their catalytic effects on the oxidative coupling of p-anisidine with N,N-dimethylaniline (DMA) to form a colored compound (lambda(max)=740 nm) in the presence of hydrogen peroxide at pH 3.2. 2,9-Dimethyl-1,10-phenanthroline (neocuproine) acted as an activator for the copper catalysis, and 1,10-phenanthroline (phen) acted as an activator for the iron catalysis. The selectivity was improved in the presence of diphosphate as a masking agent. The determinable ranges were 0.16-10 ppb for copper and 1-100 ppb for iron, respectively. The relative standard deviations of copper and iron were 1.1 and 0.97% for five determinations of 10 ppb copper and 40 ppb iron. The method was successfully applied to the analyses of copper and iron in tap, well, river and pond waters.

Fluorimetric flow injection analysis of trace amount of formaldehyde in environmental atmosphere with 5,5-dimethylcyclohexane-1,3-dione.

A simple and sensitive flow injection method with fluorimetry and 5,5-dimethylcyclohexane-1,3-dione (dimedone) was developed for the determination of formaldehyde. Formaldehyde reacted with dimedone in the presence of ammonium acetate to form a fluorescence compound, which has an excitation wavelength at 395 nm and an emission wavelength at 463 nm. A two-channel flow system was assembled. Distilled water and 0.3% dimedone buffered at pH 5.5 were delivered at 0.7 mlmin(-1) and 100 mul of sample was injected into the carrier stream. The reaction was done in the reaction system designed newly, which consists of heating and cooling devices. The chemical reactivity with formaldehyde was excellent in the reaction system and selective. The calibration graphs were linear in the range of 25-100 and 5-10 ppb. RSDs (n=10) for 50 and 10 ppb formaldehyde were 0.6 and 3.4% and the LOD (S/N=3) was 0.9 ppb. The sample throughput was 20 h(-1). The method was applied to the determination of formaldehyde in gas sample evolved from adhesive agents and in living environmental indoor. The sensitive and selective method is useful for monitoring trace of formaldehyde in the environmental atmosphere.