Effects of Capsular Reconstruction With an Iliotibial Band Allograft on Distractive Stability of the Hip Joint: A Biomechanical Study.

BACKGROUND: The capsular ligaments and the labral suction seal cooperatively manage distractive stability of the hip. Capsular reconstruction using an iliotibial band (ITB) allograft aims to address capsular insufficiency and iatrogenic instability. However, the extent to which this procedure may restore hip distractive stability after a capsular defect is unknown. PURPOSE: To evaluate the biomechanical effects of capsular reconstruction on distractive stability of the hip joint. STUDY DESIGN: Controlled laboratory study. METHODS: Eight fresh-frozen cadaveric hip specimens were dissected to the level of the capsule and axially distracted in 3 testing states: intact capsule, partial capsular defect, and capsular reconstruction with an ITB allograft. Each femur was compressed with 500 N of force and then distracted 6 mm relative to the neutral position at 0.5 mm/s. Distractive force was continuously recorded, and the first peak delineating 2 phases of hip distractive stability in the force-displacement curve was analyzed. RESULTS: The median force at maximum distraction in the capsular reconstruction state (156 N) was significantly greater than that in the capsular defect state (89 N; P = .036) but not significantly different from that in the intact state (218 N; P = .054). Median values for distractive force at first peak (60 N, 72 N, and 61 N, respectively; P = .607), distraction at first peak (2.3 mm, 2.3 mm, and 2.5 mm, respectively; P = .846), and percentage decrease in distractive force (35%, 78%, and 63%, respectively; P = .072) after the first peak were not significantly different between the intact, defect, and reconstruction states. CONCLUSION: Capsular reconstruction with an ITB allograft significantly increased the force required to distract the hip compared with a capsular defect in a cadaveric model. To our knowledge, this is the first study to report an initial peak distractive force and to propose 2 distinct phases of hip distractive stability. CLINICAL RELEVANCE: The consequences of a capsular defect on distractive stability of the hip may be underappreciated among the orthopaedic community; with that said, capsular reconstruction using an ITB allograft provided significantly increased distractive stability and should be considered an effective treatment option for patients with symptomatic capsular deficiency.

The Influence of Graft Tensioning Sequence on Tibiofemoral Orientation During Bicruciate and Posterolateral Corner Knee Ligament Reconstruction: A Biomechanical Study.

BACKGROUND: During multiple knee ligament reconstructions, the graft tensioning order may influence the final tibiofemoral orientation and corresponding knee kinematics. Nonanatomic tibiofemoral orientation may result in residual knee instability, altered joint loading, and an increased propensity for graft failure. PURPOSE: To biomechanically evaluate the effect of different graft tensioning sequences on knee tibiofemoral orientation after multiple knee ligament reconstructions in a bicruciate ligament (anterior cruciate ligament [ACL] and posterior cruciate ligament [PCL]) with a posterolateral corner (PLC)-injured knee. STUDY DESIGN: Controlled laboratory study. METHODS: Ten nonpaired, fresh-frozen human cadaveric knees were utilized for this study. After reconstruction of both cruciate ligaments and the PLC and proximal graft fixation, each knee was randomly assigned to each of 4 graft tensioning order groups: (1) PCL → ACL → PLC, (2) PCL → PLC → ACL, (3) PLC → ACL → PCL, and (4) ACL → PCL → PLC. Tibiofemoral orientation after graft tensioning was measured and compared with the intact state. RESULTS: Tensioning the ACL first (tensioning order 4) resulted in posterior displacement of the tibia at 0° by 1.7 ± 1.3 mm compared with the intact state ( P = .002). All tensioning orders resulted in significantly increased tibial anterior translation compared with the intact state at higher flexion angles ranging from 2.7 mm to 3.2 mm at 60° and from 3.1 mm to 3.4 mm at 90° for tensioning orders 1 and 2, respectively (all P < .001). There was no significant difference in tibiofemoral orientation in the sagittal plane between the tensioning orders at higher flexion angles. All tensioning orders resulted in increased tibial internal rotation (all P < .001). Tensioning and fixing the PLC first (tensioning order 3) resulted in the most increases in internal rotation of the tibia: 2.4° ± 1.9°, 2.7° ± 1.8°, and 2.0° ± 2.0° at 0°, 30°, and 60°, respectively. CONCLUSION: None of the tensioning orders restored intact knee tibiofemoral orientation. Tensioning the PLC first should be avoided in bicruciate knee ligament reconstruction with concurrent PLC reconstruction because it significantly increased tibial internal rotation. We recommend that the PCL be tensioned first, followed by the ACL, to avoid posterior translation of the tibia in extension where the knee is primarily loaded during most activities. The PLC should be tensioned last. CLINICAL RELEVANCE: This study will help guide surgeons in decision making for the graft tensioning order during multiple knee ligament reconstructions.

Use of Platelet-Rich Plasma Immediately After an Injury Did Not Improve Ligament Healing, and Increasing Platelet Concentrations Was Detrimental in an In Vivo Animal Model.

BACKGROUND: Limited information in basic science and clinical trials exists to determine if ligament healing may be accelerated with the use of biological adjuvants, such as platelet-rich plasma (PRP). However, there has been widespread acceptance of PRP for use in clinical practice, despite an inadequate understanding of its biological mechanism of action. PURPOSE: To determine whether a single dose of PRP could accelerate ligament healing and correspondingly improve histological characteristics and biomechanical properties when injected immediately postoperatively into the injured medial collateral ligament (MCL) of New Zealand White rabbits. STUDY DESIGN: Controlled laboratory study. METHODS: Eighty skeletally mature New Zealand White rabbits (160 knees) were used. The MCL was torn midbody to simulate a grade 3 tear. After an acute injury of the MCL, the administration of autologous PRP at 3 different platelet concentrations (0 million/uL, platelet-poor plasma [PPP]; 0.6 million/uL, 2 times the baseline [2× PRP]; and 1.2 million/uL, 4 times the baseline [4× PRP]) was performed and compared with a saline injection control in the contralateral knee. Histological analysis and a biomechanical endpoint characterization were utilized to assess ligamentous healing and compare it to a sham surgery group. RESULTS: The PPP ( P = .001) and 4× PRP ( P = .002) groups had a significantly lower collagen subscore than the sham surgery group. No other differences were observed among the treatment groups, including the vascularity subscore and overall ligament tissue maturity index score. Compared with saline-injected contralateral knees, the maximum load for PPP and 2× PRP was not significantly different ( P = .788 and .325, respectively). The maximum load and stiffness for knees treated with 4× PRP were significantly less than for the saline-treated contralateral knees ( P = .006 and .001, respectively). CONCLUSION: One single dose of PPP or 2× PRP at the time of injury did not improve ligament healing. In addition, 4× PRP negatively affected ligament strength and histological characteristics at 6 weeks after the injury. CLINICAL RELEVANCE: The current practice of treating knee ligament injuries with PRP may not improve healing at low doses of PRP. The decreased mechanical properties and histological appearance of the torn MCL suggest that high doses of PRP decrease the quality of repair tissue. Further in vivo studies are necessary to determine the dosing and timing of PRP administration after a ligament injury before the widespread use of PRP to treat ligament injuries is recommended.

Intraarticular arthrofibrosis of the knee alters patellofemoral contact biomechanics.

BACKGROUND: Arthrofibrosis in the suprapatellar pouch and anterior interval can develop after knee injury or surgery, resulting in anterior knee pain. These adhesions have not been biomechanically characterized. METHODS: The biomechanical effects of adhesions in the suprapatellar pouch and anterior interval during simulated quadriceps muscle contraction from 0 to 90° of knee flexion were assessed. Adhesions of the suprapatellar pouch and anterior interval were hypothesized to alter the patellofemoral contact biomechanics and increase the patellofemoral contact force compared to no adhesions. RESULTS: Across all flexion angles, suprapatellar adhesions increased the patellofemoral contact force compared to no adhesions by a mean of 80 N. Similarly, anterior interval adhesions increased the contact force by a mean of 36 N. Combined suprapatellar and anterior interval adhesions increased the mean patellofemoral contact force by 120 N. Suprapatellar adhesions resulted in a proximally translated patella from 0 to 60°, and anterior interval adhesions resulted in a distally translated patella at all flexion angles other than 15° (p < 0.05). CONCLUSIONS: The most important finding in this study was that patellofemoral contact forces were significantly increased by simulated adhesions in the suprapatellar pouch and anterior interval. Anterior knee pain and osteoarthritis may result from an increase in patellofemoral contact force due to patellar and quadriceps tendon adhesions. For these patients, arthroscopic lysis of adhesions may be beneficial.

A Contact Pressure Analysis Comparing an All-Inside and Inside-Out Surgical Repair Technique for Bucket-Handle Medial Meniscus Tears.

PURPOSE: To directly compare effectiveness of the inside-out and all-inside medial meniscal repair techniques in restoring native contact area and contact pressure across the medial tibial plateau at multiple knee flexion angles. METHODS: Twelve male, nonpaired (n = 12), fresh-frozen human cadaveric knees underwent a series of 5 consecutive states: (1) intact medial meniscus, (2) MCL tear and repair, (3) simulated bucket-handle longitudinal tear of the medial meniscus, (4) inside-out meniscal repair, and (5) all-inside meniscal repair. Knees were loaded with a 1,000-N axial compressive force at 5 knee flexion angles (0°, 30°, 45°, 60°, 90°), and contact area, mean contact pressure, and peak contact pressure were calculated using thin film pressure sensors. RESULTS: No significant differences were observed between the inside-out and all-inside repair techniques at any flexion angle for contact area, mean contact pressure, and peak contact pressure (all P > .791). Compared with the torn meniscus state, inside-out and all-inside repair techniques resulted in increased contact area at all flexion angles (all P < .005 and all P < .037, respectively), decreased mean contact pressure at all flexion angles (all P < .007 and all P < .001, respectively) except for 0° (P = .097 and P = .39, respectively), and decreased peak contact pressure at all flexion angles (all P < .001, all P < .001, respectively) except for 0° (P = .080 and P = .544, respectively). However, there were significant differences in contact area and peak contact pressure between the intact state and inside-out technique at angles ≥45° (all P < .014 and all P < .032, respectively). Additionally, there were significant differences between the intact state and all-inside technique in contact area at 60° and 90° and peak contact pressure at 90° (both P < .005 and P = .004, respectively). Median values of intact contact area, mean contact pressure, and peak contact pressure over the tested flexion angles ranged from 498 to 561 mm2, 786 to 997 N/mm2, and 1,990 to 2,215 N/mm2, respectively. CONCLUSIONS: Contact area, mean contact pressure, and peak contact pressure were not significantly different between the all-inside and inside-out repair techniques at any tested flexion angle. Both techniques adequately restored native meniscus biomechanics near an intact level. CLINICAL RELEVANCE: An all-inside repair technique provided similar, native-state-restoring contact mechanics compared with an inside-out repair technique for the treatment of displaced bucket-handle tears of the medial meniscus. Thus, both techniques may adequately decrease the likelihood of cartilage degeneration.

Functional Brace in ACL Surgery: Force Quantification in an In Vivo Study.

BACKGROUND: A need exists for a functional anterior cruciate ligament (ACL) brace that dynamically supports the knee joint to match the angle-dependent forces of a native ACL, especially in the early postoperative period. PURPOSE/HYPOTHESIS: The purpose of this study was to quantify the posteriorly directed external forces applied to the anterior proximal tibia by both a static and a dynamic force ACL brace. The proximal strap forces applied by the static force brace were hypothesized to remain relatively constant regardless of knee flexion angle compared with those of the dynamic force brace. STUDY DESIGN: Controlled laboratory study. METHODS: Seven healthy adult males (mean age, 27.4 ± 3.4 years; mean height, 1.8 ± 0.1 m; mean body mass, 84.1 ± 11.3 kg) were fitted with both a static and a dynamic force ACL brace. Participants completed 3 functional activities: unloaded extension, sit-to-stand, and stair ascent. Kinematic data were collected using traditional motion-capture techniques while posteriorly directed forces applied to the anterior aspect of both the proximal and distal tibia were simultaneously collected using a customized pressure-mapping technique. RESULTS: The mean posteriorly directed forces applied to the proximal tibia at 30° of flexion by the dynamic force brace during unloaded extension (80.2 N), sit-to-stand (57.5 N), and stair ascent (56.3 N) activities were significantly larger, regardless of force setting, than those applied by the static force brace (10.1 N, 9.5 N, and 11.9 N, respectively; P < .001). CONCLUSION: The dynamic force ACL brace, compared with the static force brace, applied significantly larger posteriorly directed forces to the anterior proximal tibia in extension, where the ACL is known to experience larger in vivo forces. Further studies are required to determine whether the physiological behavior of the brace will reduce anterior knee laxity and improve long-term patient outcomes. CLINICAL RELEVANCE: ACL braces that dynamically restrain the proximal tibia in a manner similar to physiological ACL function may improve pre- and postoperative treatment.

Biomechanical evaluation of straight antegrade nailing in proximal humeral fractures: the rationale of the "proximal anchoring point".

PURPOSE: Varus failure is one of the most common failure modes following surgical treatment of proximal humeral fractures. Straight antegrade nails (SAN) theoretically provide increased stability by anchoring to the densest zone of the proximal humerus (subchondral zone) with the end of the nail. The aim of this study was to biomechanically investigate the characteristics of this "proximal anchoring point" (PAP). We hypothesized that the PAP would improve stability compared to the same construct without the PAP. METHODS: Straight antegrade humeral nailing was performed in 20 matched pairs of human cadaveric humeri for a simulated unstable two-part fracture. RESULTS: Biomechanical testing, with stepwise increasing cyclic axial loading (50-N increments each 100 cycles) at an angle of 20° abduction revealed significantly higher median loads to failure for SAN constructs with the PAP (median, 450 N; range, 200-1.000 N) compared to those without the PAP (median, 325 N; range, 100-500 N; p = 0.009). SAN constructs with press-fit proximal extensions (endcaps) showed similar median loads to failure (median, 400 N; range, 200-650 N), when compared to the undersized, commercially available SAN endcaps (median, 450 N; range, 200-600 N; p = 0.240). CONCLUSIONS: The PAP provided significantly increased stability in SAN constructs compared to the same setup without this additional proximal anchoring point. Varus-displacing forces to the humeral head were superiorly reduced in this setting. This study provides biomechanical evidence for the "proximal anchoring point's" rationale. Straight antegrade humeral nailing may be beneficial for patients undergoing surgical treatment for unstable proximal humeral fractures to decrease secondary varus displacement and thus potentially reduce revision rates.

Anatomic and Biomechanical Comparison of the Classic and Congruent-Arc Techniques of the Latarjet Procedure.

BACKGROUND: The Latarjet procedure is commonly performed using either the classic or the congruent-arc technique. Each technique has potential clinical advantages and disadvantages. However, data on the anatomic and biomechanical effects, benefits, and limitations of each technique are limited. Hypothesis/Purpose: To compare the anatomy and biomechanical fixation strength (failure load) between the 2 techniques. It was hypothesized that the classic technique would have superior initial fixation when compared with the congruent-arc technique and that this would be affected by sex and coracoid size. STUDY DESIGN: Controlled laboratory study. METHODS: A biomechanical cadaver study was performed with 20 pairs of male and female shoulders. One of each pair of shoulders was randomly assigned to receive the classic or congruent-arc technique. Coracoid and glenoid anatomic measurements were collected before biomechanical testing. A tensile force was applied through the conjoined tendon to replicate forces experienced by the coracoid graft in the early postoperative period, and the failure load was determined for each specimen. RESULTS: The mean ± SD surface area available for fixation was 263 ± 63 mm2 in the classic technique compared with 177 ± 63 mm2 in the congruent-arc group ( P < .001). 36% of the glenoid width was recreated in the classic group and 50% in the congruent-arc group ( P < .001). The congruent-arc technique resulted in a significantly lower ( P = .005) mean failure load (239 ± 91 N) compared with the classic technique (303 ± 114 N). Failure load was significantly higher in males ( P = .037); male specimens had a mean failure load of 344 ± 122 N for the classic technique and 289 ± 73 N for the congruent-arc technique, and females had a mean failure load of 266 ± 98 N and 194 ± 84 N, respectively. CONCLUSION: In this biomechanical model, the classic technique of the Latarjet procedure provided a greater surface area for healing to the glenoid and superior initial fixation when compared with the congruent-arc technique. The congruent-arc technique allowed restoration of a larger glenoid defect. CLINICAL RELEVANCE: The classic and congruent-arc techniques of coracoid transfer have anatomic and biomechanical advantages and disadvantages that should be considered when choosing between the 2 techniques.

Quantitative and Computed Tomography Anatomic Analysis of Glenoid Fixation for Superior Capsule Reconstruction: A Cadaveric Study.

PURPOSE: To investigate glenoid fixation for superior capsule reconstruction (SCR) and evaluate anchor positions, intraosseous trajectories, and proximity to the suprascapular nerve (SSN) and glenoid fossa. The secondary purpose was to provide technical pearls and pitfalls for anchor insertion on the superior glenoid during SCR. METHODS: Three beath pins were arthroscopically inserted into 12 (n = 12) nonpaired human cadaveric shoulders through Neviaser, anterior, and posterior portals to simulate anchor placement on the superior glenoid during SCR. Computed tomography scans were performed to evaluate anchor positioning and insertion trajectories. Specimens were then dissected to delineate the anatomic relations of the beath pins to the SSN and glenoid fossa. RESULTS: The superior glenoid anchor position was a mean 15.0 ± 4.0 mm to the SSN and 6.5 ± 1.7 mm to the glenoid fossa. The posterior glenoid anchor position was a mean 11.8 ± 2.1 mm to the SSN and 2.9 ± 2.9 mm to the glenoid fossa. On average, the superior pin was placed at 12:30 ± 0:30 (left-sided glenoid clock face) and inserted at 19° ± 9° with respect to the sagittal plane of the glenoid, the anterior pin was placed at 11:00 ± 0:30 and inserted 40° ± 17° off the glenoid, and the posterior pin was placed at 3:00 ± 1:00 and inserted at 52° ± 12° off the glenoid. CONCLUSIONS: The results of the present cadaveric study showed that glenoid fixation was safe with respect to the SSN and delineated technical guidelines and trajectories for inserting 3 anchors into the glenoid. CLINICAL RELEVANCE: This study shows that 3 anchors can be inserted into the glenoid without a risk of SSN damage and delineates technical guidelines for anchor insertion.

Comparison of Radiographs and Computed Tomography for the Screening of Anterior Inferior Iliac Spine Impingement.

PURPOSE: To compare radiographic and 3-dimensional (3D) computed tomography (CT) imaging modalities for the screening of anterior inferior iliac spine (AIIS) impingement by establishing imaging measurement related to the AIIS. METHODS: Anteroposterior and false-profile radiographs and 3D CT scans were obtained on 10 human cadaveric pelvises. On the anteroposterior view for each methodology, 2 measurements were calculated: distance to the most lateral AIIS from the 12 o'clock position on the acetabular rim, and the angle between the lateral AIIS and the sagittal plane. On the false-profile view for each methodology, 2 measurements were calculated: distance to the anterior AIIS from the 12 o'clock position on the acetabular rim, and the angle between the anterior AIIS and the sagittal plane. Inter-rater and intrarater reliability analyses were performed for both methods in addition to an intermethod analysis. RESULTS: The radiographic false-profile view was the most repeatable orientation, with intraclass correlation coefficients showing excellent reproducibility in both inter-rater (angle: 0.980, distance: 0.883) and intrarater (angle: 0.995, distance: 0.995) analyses. The mean distance from the 12 o'clock position of the acetabular rim to the most anterior/lateral aspect of the AIIS was 41.4 mm and 16.0 mm on the radiographic false-profile and anteroposterior views, respectively. Intermethod analysis showed a systematic, quantitative bias between modalities (anteroposterior view: -4.1 mm, 6.7°; false-profile view: -0.1 mm, 8.3°), which will remain relatively consistent as evidenced by the strong individual reproducibility of each measurement. CONCLUSIONS: AIIS morphology in relation to the acetabular rim 12 o'clock position and its angle relative to the sagittal plane can be quantitatively determined using either radiographic or 3D CT imaging modalities. CLINICAL RELEVANCE: Radiographic evaluation may be a valuable tool in the screening of AIIS impingement.

Computed tomography-based prediction of the straight antegrade humeral nail's entry point and exposure of "critical types": truth or fiction?

BACKGROUND: Straight antegrade intramedullary nailing of proximal humerus fractures has shown promising clinical results. However, up to 36% of all humeri seem to be "critical types" in terms of the potential violation of the supraspinatus (SSP) tendon footprint by the nail's insertion zone. The aims of this study were to evaluate if a computed tomography (CT) scan could reliably predict the nail's entry point on the humeral head and if it would be possible to preoperatively estimate the individual risk of iatrogenic violation of the SSP tendon footprint by evaluating the uninjured contralateral humerus. METHODS: Twenty matched pairs of human cadaveric shoulders underwent CT scans, and the entry point for an antegrade nail as well as measurements regarding critical distances between the entry point and the rotator cuff were determined. Next, gross anatomic measurements of the same data were performed and compared. Furthermore, specimens were reviewed for critical types. RESULTS: Overall, 42.5% of all specimens were found to be critical types. The CT measurements exhibited excellent intra-rater and inter-rater reliability (intraclass correlation coefficients >0.90). Similarly, excellent agreement between the CT scan and gross anatomic measurements in contralateral shoulders (intraclass correlation coefficients >0.88) was found. CONCLUSION: Assessing the uninjured contralateral side, CT can reliably predict the entry point in antegrade humeral nailing and preoperatively identify critical types of humeral heads at risk of iatrogenic implantation damage to the SSP tendon footprint. This study may help surgeons in the decision-making processon which surgical technique should be used without putting the patient at risk for iatrogenic, implant-related damage to the rotator cuff.

Double-bundle posterior cruciate ligament reconstruction: a biomechanical analysis of simulated early motion and partial and full weightbearing on common reconstruction grafts.

PURPOSE: The purpose of this study was to determine the biomechanical effects of simulated immediate motion and weightbearing during rehabilitation on different double-bundle posterior cruciate ligament reconstruction (DB-PCLR) graft options. METHODS: Nine each of commercially prepared (allograft) Achilles tendon allografts, fresh-frozen (autograft) bone-patellar tendon-bone grafts, and fresh-frozen quadriceps tendon grafts were paired with commercially prepared anterior tibialis allografts, fresh-frozen semitendinosus grafts, and fresh-frozen semitendinosus grafts, respectively. Graft pairs were loaded to simulate early range of motion on a stationary bicycle, partial weightbearing (30 %), and full weightbearing. RESULTS: Acquired laxity (displacement, mm) between graft pairs was not significantly different during simulated early range of motion. However, during simulated partial weightbearing, the median acquired laxity of the patellar tendon/semitendinosus pair (1.06 mm) was significantly less than that of the quadriceps tendon/semitendinosus (1.50 mm, p = 0.01) and Achilles/anterior tibialis (1.44 mm, p = 0.003) graft pairs. During simulated full weightbearing, significantly less acquired laxity was observed for the patellar tendon/semitendinosus graft pair (2.38 mm) compared to the Achilles/anterior tibialis pair (4.85 mm, p = 0.04), but a significant difference was not observed compared to the QT/semitendinosus graft pair (3.91 mm, n.s.). There were no significant differences in the ultimate loads between any of the graft pairs. CONCLUSIONS: Simulated early range of motion and early partial weightbearing did not result in clinically significant acquired graft laxity in common graft options utilized for DB-PCLR. However, simulated full weightbearing did result in clinically significant acquired graft laxity, and therefore, early rehabilitation protocols should avoid implementing full weightbearing that could contribute to graft failure.

Biomechanical Comparison of 3 Current Ankle Syndesmosis Repair Techniques.

BACKGROUND: Significant debate exists regarding optimal repair for unstable syndesmosis injuries. Techniques range from screw fixation, suture-button fixation, or a combination of the two. In this study, 3 common repairs were compared using a simulated weightbearing protocol with internal and external rotation of the foot. METHODS: Twenty-four lower leg specimens with mean age 54 years (range, 38-68 years) were used for testing. Following creation of a complete syndesmotic injury (AITFL, ITFL, PITFL, interosseous membrane), specimens were repaired using 1 of 3 randomly assigned techniques: (1) one 3.5-mm syndesmotic screw, (2) 1 suture-button construct, and (3) 2 divergent suture-button constructs. Repairs were cycled for 500 cycles between 7.5 Nm of internal/external rotation torque under a constant 750 N axial compressive load in a neutral dorsiflexion position. At 0, 10, 100, and 500 cycles, torsional cyclic loading was interrupted to assess torsional resistance to rotation within a physiologic range of motion (15 degrees external rotation to 10 degrees internal rotation). Torque (Nm), rotational position (degrees), and 3-dimensional data were collected throughout the testing to characterize relative spatial relationships of the tibiofibular articulation. RESULTS: There were no significant differences between repair techniques in resistance to internal and external rotation with respect to the intact syndesmosis. Three-dimensional analysis revealed significant differences between repair techniques for sagittal fibular translation with external rotation of the foot. Screw fixation had the smallest magnitude of posterior sagittal translation (2.5 mm), and a single suture-button construct demonstrated the largest magnitude of posterior sagittal translation (4.6 mm). Screw fixation also allowed for significantly less anterior sagittal translation with internal rotation of the foot (0.1 mm) when compared to both 1 (2.7 mm) and 2 (2.9 mm) suture-button constructs. CONCLUSION: All repairs provided comparable rotational stability to the syndesmosis; however, no repair technique completely restored rotational stability and tibiofibular anatomic relationships of the preinjury state. CLINICAL RELEVANCE: Constructs were comparable across most conditions; however, when repairing injuries with a suture-button construct, a single suture-button construct may not provide sufficient resistance to sagittal translation of the fibula.

A 3-D CT Analysis of Screw and Suture-Button Fixation of the Syndesmosis.

BACKGROUND: Historically, syndesmosis injuries have been repaired with screw fixation; however, some suggest that suture-button constructs may provide a more accurate anatomic and physiologic reduction. The purpose of this study was to compare changes in the volume of the syndesmotic space following screw or suture-button fixation using a preinjury and postoperative 3-D computed tomography (CT) model. The null hypothesis was that no difference would be observed among repair techniques. METHODS: Twelve pairs of cadaveric specimens were dissected to identify the syndesmotic ligaments. Specimens were imaged with CT prior to the creation of a complete syndesmosis injury and were subsequently repaired using 1 of 3 randomly assigned techniques: (a) one 3.5-mm cortical screw, (b) 1 suture-button, and (c) 2 suture-buttons. Specimens were imaged postoperatively with CT. 3-D models of all scans and tibiofibular joint space volumes were calculated to assess restoration of the native syndesmosis. Analysis of variance and Tukey's method were used to compare least squares mean differences from the intact syndesmosis among repair techniques. RESULTS: For each of the 3 fixation methods, the total postoperative syndesmosis volume was significantly decreased relative to the intact state. The total mean decreases in volume compared with the intact state for the 1-suture-button construct, 2-suture-button construct, and syndesmotic screw were -561 mm3 (95% CI, -878 to -244), -964 mm3 (95% CI, -1281 to -647) and -377 mm3 (95% CI, -694 to -60), respectively. CONCLUSION: All repairs notably reduced the volume of the syndesmosis beyond the intact state. Fixation with 1 suture-button was not significantly different from screw or 2-suture-button fixation; however, fixation with 2 suture-buttons resulted in significantly decreased volume compared with screw fixation. CLINICAL RELEVANCE: The results of this study suggest that the 1-suture-button repair technique and the screw fixation repair technique were comparable for reduction of syndesmosis injuries, although both may overcompress the syndesmosis.

High-load preconditioning of human soft tissue hamstring grafts: An in vitro biomechanical analysis.

PURPOSE: In order to minimize viscoelastic elongation of ACL reconstruction grafts, preconditioning protocols have been employed in clinical practice prior to final graft fixation. The purpose of this study was to evaluate two separate high-load static preconditioning protocols of double-looped semitendinosus-gracilis grafts and compare these results to both a current clinical protocol and a control group with no preconditioning protocol applied. It was hypothesized that a high-load, static preconditioning protocol would minimize graft elongation during a simulated progressive early rehabilitation compared to both the "89 N" clinical protocol and control groups. METHODS: Grafts were randomly allocated into four preconditioning study groups: (1) control (no preconditioning), (2) clinical protocol (89 N for 15 min), (3) high-load, short duration (600 N for 20 s), and (4) high-load, long duration (600 N for 15 min). After preconditioning, grafts were cyclically loaded between 10 and 400 N at 0.5 Hz for 450 cycles to simulate early postoperative rehabilitation. Graft displacement (elongation) was recorded during both preconditioning and cyclic loading. RESULTS: Increased preconditioning load magnitude and duration significantly reduced graft elongation during cyclic loading (p < 0.05) which corresponded to an inverse relationship with increased elongation during preconditioning. The "600 N for 15 min" protocol resulted in significantly less elongation during simulated early rehabilitation than both the control group and the "89 N for 15 min" protocol (p < 0.001, p < 0.05). CONCLUSIONS: Graft elongation during simulated early rehabilitation was significantly reduced by a high-load preconditioning protocol applied for an extended period of time compared to a current common clinical protocol and grafts that were not preconditioned. In addition, the amount of elongation during simulated early rehabilitation was similar between grafts preconditioned using the current clinical practice protocol and the high-load/short-duration protocol, implying that the latter could potentially induce the same viscoelastic changes in soft tissue grafts as the current clinical practice. The "600 N for 20 s" preconditioning protocol may provide similar postoperative results as the clinical protocol, "89 N for 15 min", and also reduce or maintain operative time. A high-load preconditioning protocol that reduces graft elongation may benefit patients undergoing ACL reconstruction, especially for cases of failed primary reconstruction, genu recurvatum, and increased tibial slope, where maintaining graft length is imperative to restore knee stability.

Hip Capsular Closure: A Biomechanical Analysis of Failure Torque.

BACKGROUND: Hip capsulotomy is routinely performed during arthroscopic surgery to achieve adequate exposure of the joint. Iatrogenic instability can result after hip arthroscopic surgery because of capsular insufficiency, which can be avoided with effective closure of the hip capsule. There is currently no consensus in the literature regarding the optimal quantity of sutures upon capsular closure to achieve maximal stability postoperatively. Purpose/Hypothesis: The purpose of this study was to determine the failure torques of 1-, 2-, and 3-suture constructs for hip capsular closure to resist external rotation and extension after standard anterosuperior interportal capsulotomy (12 to 3 o'clock). Additionally, the degree of external rotation at which the suture constructs failed was recorded. The null hypothesis of this study was that no significant differences with respect to the failure torque would be found between the 3 repair constructs. STUDY DESIGN: Controlled laboratory study. METHODS: Nine pairs (n = 18) of fresh-frozen human cadaveric hemipelvises underwent anterosuperior interportal capsulotomy, which were repaired with 1, 2, or 3 side-to-side sutures. Each hip was secured in a dynamic biaxial testing machine and underwent a cyclic external rotation preconditioning protocol, followed by external rotation to failure. RESULTS: The failure torque of the 1-suture hip capsular closure construct was significantly less than that of the 3-suture construct. The median failure torque for the 1-suture construct was 67.4 N·m (range, 47.4-73.6 N·m). The median failure torque was 85.7 N·m (range, 56.9-99.1 N·m) for the 2-suture construct and 91.7 N·m (range, 74.7-99.0 N·m) for the 3-suture construct. All 3 repair constructs exhibited a median 36° (range, 22°-64°) of external rotation at the failure torque. CONCLUSION: The most important finding of this study was that the 2- and 3-suture constructs resulted in comparable biomechanical failure torques when external rotation forces were applied to conventional hip capsulotomy in a cadaveric model. The 3-suture construct was significantly stronger than the 1-suture construct; however, there was not a significant difference between the 2- and 3-suture constructs. Additionally, all constructs failed at approximately 36° of external rotation. CLINICAL RELEVANCE: Re-establishing the native anatomy of the hip capsule after hip arthroscopic surgery has been reported to result in improved outcomes and reduce the risk of iatrogenic instability. Therefore, adequate capsular closure is important to restore proper hip biomechanics, and postoperative precautions limiting external rotation should be utilized to protect the repair.

Impact of Arthroscopic Lateral Acromioplasty on the Mechanical and Structural Integrity of the Lateral Deltoid Origin: A Cadaveric Study.

PURPOSE: To determine whether a 5-mm and/or 10-mm arthroscopic lateral acromioplasty (ALA) would weaken the structural and mechanical integrity of the lateral deltoid. METHODS: The acromion and lateral deltoid origin were harvested from 15 pairs (n = 30) of fresh-frozen human cadaveric shoulder specimens. One side of each specimen pair (left or right) was randomly assigned to either a 5-mm (n = 7) or 10-mm (n = 8) ALA group, and the contralateral sides (n = 15) were used as matched controls. Acromion thickness and width were measured pre- and postoperatively. After ALA, specimens were inspected for damage to the lateral deltoid origin. Each specimen was secured within a dynamic testing machine, and the deltoid muscle was pulled to failure. Statistical analysis was performed to determine whether ALA reduced the lateral deltoid's failure load. RESULTS: There was no significant difference in failure load between the 5-mm ALA group (661 ± 207 N) and its matched control group (744 ± 212 N; mean difference = 83 N; 95% confidence interval [CI], -91 to 258; P = .285) nor between the 10-mm ALA group (544 ± 210 N) and its matched control group (598 ± 157 N; mean difference = 54 N; 95% CI, -141 to 250; P = .532). There was no correlation found between the amount of bone resected (measured by percent thickness and width of the acromion after ALA) and the failure load of the deltoid. Visual evaluation of the acromion after ALA revealed the lateral deltoid origin had no damage in any case. CONCLUSIONS: ALA did not weaken the structural or mechanical integrity of the lateral deltoid origin. Neither a 5-mm nor a 10-mm ALA significantly reduced the deltoid's failure load. The lateral deltoid origin was not macroscopically damaged in any case. CLINICAL RELEVANCE: ALA can be performed without the potential risk of macroscopically damaging the lateral deltoid origin or reducing its failure load.

Multiple Ligament Reconstruction Femoral Tunnels: Intertunnel Relationships and Guidelines to Avoid Convergence.

BACKGROUND: Knee dislocations often require multiple concurrent ligament reconstructions, which involve creating several tunnels in the distal femur. Therefore, the risk of tunnel convergence is increased because of the limited bone volume within the distal aspect of the femur. PURPOSE: To assess the risk of tunnel convergence and determine the optimal reconstruction tunnel orientations for multiple ligament reconstructions in the femur. STUDY DESIGN: Descriptive laboratory study. METHODS: Three-dimensional knee models were developed from computed tomography scans of 21 patients. Medical image processing software was used to create tunnels for each of the primary ligamentous structures, replicating a surgical approach that would be used in multiple ligament reconstructions. Thereafter, the tunnel orientation was varied in surgically relevant directions to determine orientations that minimized the risk of tunnel convergence. The orientation of the anterior cruciate ligament (ACL) and posterior cruciate ligament (PCL) tunnels was held constant throughout the study, while the orientation of the fibular collateral ligament (FCL), popliteus tendon (PLT), superficial medial collateral ligament (sMCL), and posterior oblique ligament (POL) tunnels was varied to avoid convergence. RESULTS: A high risk of tunnel convergence was observed between the FCL and ACL tunnels when the FCL tunnel was aimed at 0° in the axial and coronal planes. Aiming the FCL tunnel 35° anteriorly minimized convergence with the ACL tunnel. No tunnel convergence was observed for the PLT tunnel aimed 35° anteriorly and parallel to the FCL tunnel. To avoid convergence between the sMCL and PCL tunnels, the sMCL tunnels should be aimed 40° proximally in the coronal plane and 20° to 40° anteriorly. During concomitant POL reconstruction, the sMCL should be aimed 40° proximally and anteriorly and the POL 20° proximally and anteriorly. The PLT and POL tunnels aimed at 0° in both the coronal and axial planes had an increased risk of violating the intercondylar notch. CONCLUSION: Femoral tunnel orientations during multiple ligament reconstructions need to be adjusted to avoid tunnel convergence. On the lateral side, aiming the FCL and PLT tunnels 35° anteriorly eliminated convergence with the ACL tunnel. On the medial side, tunnel convergence was avoided by orienting the sMCL tunnel 40° proximally and anteriorly and the POL tunnel 20° proximally and anteriorly. The POL and PLT tunnels aimed at 0° in the axial plane had an increased risk of violating the intercondylar notch. CLINICAL RELEVANCE: The risk of tunnel convergence with the ACL and PCL femoral tunnels can be reduced by adjusting the orientation of the FCL and PLT tunnels and the sMCL and POL tunnels, respectively.

Anatomic Anterolateral Ligament Reconstruction of the Knee Leads to Overconstraint at Any Fixation Angle.

BACKGROUND: Anterior cruciate ligament (ACL) tears are one of the most common injuries among athletes. However, the ability to fully restore rotational stability with ACL reconstruction (ACLR) remains a challenge, as evidenced by the persistence of rotational instability in up to 25% of patients after surgery. Advocacy for reconstruction of the anterolateral ligament (ALL) is rapidly increasing because some biomechanical studies have reported that the ALL is a significant contributor to internal rotational stability of the knee. HYPOTHESIS/PURPOSE: The purpose of this study was to assess the effect of ALL reconstruction (ALLR) graft fixation angle on knee joint kinematics in the clinically relevant setting of a concomitant ACLR and to determine the optimal ALLR graft fixation angle. It was hypothesized that all fixation angles would significantly reduce rotational laxity compared with the sectioned ALL state. STUDY DESIGN: Controlled laboratory study. METHODS: Ten nonpaired fresh-frozen human cadaveric knees underwent a full kinematic assessment in each of the following states: (1) intact; (2) anatomic single-bundle (SB) ACLR with intact ALL; (3) anatomic SB ACLR with sectioned ALL; (4) anatomic SB ACLR with 7 anatomic ALLR states using graft fixation angles of 0°, 15°, 30°, 45°, 60°, 75°, and 90°; and (5) sectioned ACL and ALL. Internal rotation during a 5-N·m internal rotation torque and anterior translation during an 88-N anterior load were recorded at 15° flexion intervals between 0° and 120°. Axial plane translation and internal rotation during a simulated pivot-shift test (combined 5-N·m internal rotation and 10-N·m valgus torques) were recorded between 0° and 60°. Kinematic changes were measured and compared with the intact state for all reconstructed and sectioned states. RESULTS: Anatomic ALLR at all graft fixation angles significantly overconstrained internal rotation of the knee joint beyond 30° of flexion and at 45° and 60° during the pivot-shift test. Furthermore, there were no significant knee kinematic differences between any tested graft fixation angles during anterior drawer, pivot-shift, and internal rotation tests. CONCLUSION: Anatomic ALLR in conjunction with an ACLR significantly reduced rotatory laxity of the knee beyond 30° of knee flexion. However, ALLR, regardless of fixation angle, resulted in significant overconstraint of the knee. CLINICAL RELEVANCE: ALLR at any fixation angle overconstrained native joint kinematics and should be performed with careful consideration. Further investigation into the application and target population for ALLR is strongly recommended.

Biomechanical Results of Lateral Extra-articular Tenodesis Procedures of the Knee: A Systematic Review.

PURPOSE: To systematically review and compare biomechanical results of lateral extra-articular tenodesis (LET) procedures. METHODS: A systematic review was performed using the PubMed, Medline, Embase, and Cochrane databases. The search terms included the following: extraarticular, anterolateral, iliotibial, tenodesis, plasty, augmentation, procedure, reconstruction, technique, biomechanics, kinematic, robot, cadaver, knee, lateral tenodesis, ACL, Marcacci, Lemaire, Losee, Macintosh, Ellison, Andrews, Hughston, and Muller. The inclusion criteria were nonanatomic, in vitro biomechanical studies, defined as in vitro investigations of joint motion resulting from controlled, applied forces. RESULTS: Of the 10 included studies, 7 analyzed anterior tibial translation and reported that isolated LET procedures did not restore normal anterior stability to the anterior cruciate ligament (ACL)-deficient knee. Seven of the 8 studies analyzing tibial rotation reported a reduction in internal tibial rotation across various flexion angles in the ACL-deficient knee when compared with the native state. Five studies reported a reduction in intra-articular graft force with the addition of an LET. Two studies evaluated length change patterns, graft course, and total strain range and found that reconstruction techniques in which the graft attached proximal to the lateral epicondyle and coursed deep to the fibular collateral ligament were most isometric. CONCLUSIONS: In the ACL-deficient knee, LET procedures overconstrained the knee and restricted internal tibial rotation when compared with the native state. In addition, isolated LET procedures did not return normal anterior stability to the ACL-deficient knee but did significantly reduce anterior tibial translation and intra-articular graft forces during anteriorly directed loading. CLINICAL RELEVANCE: Combined injury to the ACL and anterolateral structures has been reported to exhibit greater anterolateral rotatory instability when compared with isolated ACL injuries. Despite the reported risk of joint over-constraint, consideration should be given to reconstructing the anterolateral structures and the ACL concurrently to maximally restore both anterior tibial translation and rotatory stability.