The Effect of Cigarettes Smoke on the Color and Properties of a Silicone for Maxillofacial Prostheses.

Although deterioration of silicone maxillofacial prostheses is severely accentuated in smoking patients, the phenomenon has not been systematically studied. To address a gap in the literature concerning the stability of maxillofacial prostheses during service, in this contribution, the effect of cigarette smoke on the aspect and physical properties of M511 silicone elastomer was evaluated. The aspect, surface, and overall properties of the silicone material, pigmented or not, were followed by AFM, color measurements, FTIR, water contact angle measurements, TGA-DTG and DSC, hardness and compression stress-strain measurements. The types of the contaminants adsorbed were assessed by XRF, ESI-MS, MALDI-MS, and NMR spectral analyses. Important modifications in color, contact angle, surface roughness, local mechanical properties, and thermal properties were found in the silicone material for maxillofacial prostheses after exposure to cigarettes smoke. The presence of lead, nicotine, and several other organic compounds adsorbed into the silicone material was emphasized. Slight decrease in hardness and increase in Young's modulus was found. The combined data show important impact of cigarette smoke on the silicone physical properties and could indicate chemical transformations by secondary cross-linking. To our knowledge, this is the first study making use of complementary physical methods to assess the effect of cigarette smoke on the aspect and integrity of silicone materials for maxillofacial prostheses.

Effects of Atmospheric Pressure Plasma Jet on 3D-Printed Acrylonitrile Butadiene Styrene (ABS).

Polymers are essential in several sectors, yet some applications necessitate surface modification. One practical and eco-friendly option is non-thermal plasma exposure. The present research endeavors to examine the impacts of dielectric barrier discharge atmospheric pressure plasma on the chemical composition and wettability properties of acrylonitrile butadiene styrene surfaces subject to the action of additive manufacturing. The plasma source was produced by igniting either helium or argon and then adjusted to maximize the operational conditions for exposing polymers. The drop in contact angle and the improvement in wettability after plasma exposure can be due to the increased oxygen-containing groups onto the surface, together with a reduction in carbon content. The research findings indicated that plasma treatment significantly improved the wettability of the polymer surface, with an increase of up to 60% for both working gases, while the polar index increased from 0.01 up to 0.99 after plasma treatment. XPS measurements showed an increase of up to 10% in oxygen groups at the surface of He-plasma-treated samples and up to 13% after Ar-plasma treatment. Significant modifications were observed in the structure that led to a reduction of its roughness by 50% and also caused a leveling effect after plasma treatment. A slight decrease in the glass and melting temperature after plasma treatment was pointed out by differential scanning calorimetry and broadband dielectric spectroscopy. Up to a 15% crystallinity index was determined after plasma treatment, and the 3D printing process was measured through X-ray diffraction. The empirical findings encourage the implementation of atmospheric pressure plasma-based techniques for the environmentally sustainable manipulation of polymers for applications necessitating higher levels of adhesion and specific prerequisites.

Dextran coated iron oxide nanoparticles loaded with protocatechuic acid as multifunctional therapeutic agents.

Nowadays, there is a growing interest in multifunctional therapeutic agents as valuable tools to improve and expand the applicability field of traditional bioactive compounds. In this context, the synthesis and main characteristics of dextran-coated iron oxide nanoparticles (IONP-Dex) loaded with both an antioxidant, protocatechuic acid (PCA), and an antibiotic, ceftazidime (CAZ) or levofloxacin (LEV) are herein reported for the first time, with emphasis on the potentiation effect of PCA on drugs activity. All nanoparticles were characterized by transmission electron microscopy, X-ray diffraction, vibrating sample magnetometry, differential scanning calorimetry and dynamic light scattering. As evidenced by DPPH method, IONP-Dex loaded with PCA and LEV had similar antioxidant activity like those with PCA only, but higher than PCA and CAZ loaded ones. A synergy of action between PCA and each antibiotic co-loaded on IONP-Dex has been highlighted by an enhanced activity against reference bacterial strains, such as S. aureus and E. coli after 40 min of incubation. It was concluded that PCA, which is the main cause of the antioxidative properties of loaded nanoparticles, further improves the antimicrobial activity of IONP-Dex nanoparticles when was co-loaded with CAZ or LEV antibiotics. All constructs also showed a good biocompatibility with normal human dermal fibroblasts.

Surface Degradation of DGEBA Epoxy Resins Cured with Structurally Different Amine Hardeners: Effects of UV Radiation.

In this study, the effects of three diamine curing agents (aromatic, cycloaliphatic, aliphatic) on the photochemical behavior of bisphenol A diglycidyl ether networks were comparatively examined. In order to monitor structural changes and study the curing agents' action mode, the cured epoxy resins were characterized before and after photoirradiation by means of Fourier-transform infrared spectroscopy, contact angle, differential scanning calorimetry, scanning electron microscopy, and energy-dispersive X-ray analysis, mass loss, and color modification measurements. Water absorption tests were also conducted. The cured epoxy resins are to be used in different multicomponent polymer materials for outdoor protection. The presence of the cycloaliphatic hardener led to reduced water absorption, and after UV irradiation, an increase in the glass transition temperature and lowest mass loss of the corresponding cured epoxy resin compared to the ones cured with aromatic and aliphatic hardener.

Antibacterial Polysiloxane Polymers and Coatings for Cochlear Implants.

Within this study, new materials were synthesized and characterized based on polysiloxane modified with different ratios of N-acetyl-l-cysteine (NAC) and crosslinked via UV-assisted thiol-ene addition, in order to obtain efficient membranes able to resist bacterial adherence and biofilm formation. These membranes were subjected to in vitro testing for microbial adherence against S. pneumoniae using standardized tests. WISTAR rats were implanted for 4 weeks with crosslinked siloxane samples without and with NAC. A set of physical characterization methods was employed to assess the chemical structure and morphological aspects of the new synthetized materials before and after contact with the microbiological medium.

Radiation Processing and Characterization of Some Ethylene-propylene-diene Terpolymer/Butyl (Halobutyl) Rubber/Nanosilica Composites.

Composites based on ethylene-propylene-diene terpolymer (EPDM), butyl/halobutyl rubber and nanosilica were prepared by melt mixing and subjected to different doses of electron beam irradiation. The effect of irradiation dose on the mechanical properties, morphology, glass transition temperature, thermal stability and water uptake was investigated. The efficiency of the crosslinking by electron beam irradiation was analyzed by Charlesby-Pinner parameter evaluation and crosslink density measurements. The scanning electron microscopy data showed a good dispersion of nanosilica in the rubber matrix. An improvement in hardness and 100% modulus was revealed by increasing irradiation dose up to 150 kGy. The interaction between polymer matrix and nanosilica was analyzed using the Kraus equation. Additionally, these results indicated that the mechanical properties, surface characteristics, and water uptake were dependent on crosslink characteristics.

A new sponge-type hydrogel based on hyaluronic acid and poly(methylvinylether-alt-maleic acid) as a 3D platform for tumor cell growth.

A new sponge-type hydrogel was obtained by cross-linking hyaluronic acid (HA) and poly(methylvinylether-alt-maleic acid) P(MVE-alt-MA) through a solvent-free thermal method. The sponge-type hydrogel was characterized and checked as a support for cell growth. The influence of concentration and weight ratio of polymers on the morphology and hydrogel stability was investigated. The total polymers concentration of 3% (w/w) and the weight ratio of 1:1 were optimal for the synthesis of a stable hydrogel (HA3P50) and to promote cell proliferation. The swelling measurements revealed a high-water absorption capacity of the hydrogel in basic medium. Diphenhydramine (DPH), lidocaine (Lid) and propranolol (Prop) were loaded within the hydrogel as a model drugs to investigate the ability of drug transport and release. In vitro studies revealed that HA3P50 hydrogel promoted the adhesion and proliferation of human hepatocellular carcinoma cell line HepG2, providing a good support for 3D cell culture to obtain surrogate tumor scaffold suitable for preclinical anti-cancer drug screening.

Blends of sodium deoxycholate-based poly(ester ether)urethane ionomer and hydroxypropylcellulose with mucosal adhesiveness.

New mucoadhesive blends of sodium deoxycholate-based poly(ester ether)urethane ionomer (PU) and hydroxypropyl cellulose (HPC) are prepared. The presence of the intermolecular interactions between the polymeric components has been investigated by FTIR spectroscopy indicating their miscibility in the solid phase. DSC studies also revealed a single glass transition of the blends, which is indicative of miscibility of PU and HPC in the amorphous phase. The amount of HPC in the blends influences strongly the physicochemical and mucoadhesion/bioadhesion properties. It was found that the value of area attributed to ordered hydrogen bonding (FTIR), the onset temperature values of thermal degradation in N2 flow (TG/DTG), the values of the sorption capacity (Dynamic Vapor Sorption-DVS), the values of the apparent viscosity (rheological measurements) and mucoadhesion/bioadhesion properties increased by increasing the HPC content in the blends. Complex viscosity revealed shear thinning behavior for all the studied solutions evidencing the contributive role of polymer viscoelasticity on mucoadhesion. It was found that both G' and G" increase with an increase in angular frequency and G">G' which is characteristic for liquid-like (sol state) behavior for all blended solutions and this behavior is helpful in the adhesion with mucosa surface. Mucoadhesion of PU/HPC blends was assessed in the stomach mucosa at pH 2.6 and 37 °C. Bioadhesion test was performed at pH 7.4 and 37 °C and revealed a stronger interaction of PU/HPC blends with cellulose membrane than with stomach mucosa. The similar nature of the HPC and cellulose membrane determines additional adhesion forces and implicity high adhesion properties. The HPC component increases the hydrophilicity of the blends as DVS analysis revealed, but also leads to hydrolytic degradation. FTIR spectroscopy analysis was used to evaluate the hydrolytic stability in acid (pH 2.6) and slightly alkaline (pH 7.4) PBS media and a mechanism of degradation has been proposed.

Development of antioxidant and antimicrobial xanthan-based cryogels with tuned porous morphology and controlled swelling features.

Novel porous films based on xanthan gum (XG), poly(vinyl alcohol) (PVA), and red grape pomace (RGP), as entrapped natural antioxidant agent, were prepared by freeze/thawing, a versatile and non-destructive method. The stability of XG/PVA films was dependent on the crystalline zones created by PVA under freeze/thawing treatment. After three cryogenic cycles, the introduction of RGP into the 3D polymer matrix plays a major role by hindering the access of water into the cavities already formed during the first and second cryogenic cycles. By contrast, XG/PVA-based cryogels with enhanced mechanical strength were obtained when the number of freeze/thawing cycles increased from three to seven, while pores stability was improved by entrapment of RGP. The remarkable antioxidant and antimicrobial activity of XG/PVA/RGP cryogel films compared to the XG/PVA films, indicates the potential application of these systems in food packaging.

Duodenoscope-Associated Infections beyond the Elevator Channel: Alternative Causes for Difficult Reprocessing.

OBJECTIVES: Duodenoscopes have been widely used for both diagnostic and therapeutic endoscopic retrograde cholangiopancreatography (ERCP) procedures, but recently, numerous outbreaks of multidrug-resistant organisms (MDRO) infections have been reported which has led to extensive research for their possible causes. Consequently, the aim of this study is to search for possible duodenoscope surface damages that could provide an alternative and plausible source of infections. MATERIALS AND METHODS: In order to assess both outer and inner surfaces, a duodenoscope was dismantled and samples were taken from the outer resin polymer and from the air/water, elevator, and working (biopsy) channels that were characterized by FTIR, DSC, TGA, AFM, SEM techniques and the antimicrobial activity were tested. RESULTS: Alterations were noticed on both the coating and working channel polymers, with external alterations increasing progressively from the proximal sample to the distal sample near the tip of the scope. However, the results showed that the coating surface was still efficient against bacterial adhesion. Changes in surface texture and also morphological changes were shown. CONCLUSIONS: The study describes the impact of routine procedural use and reprocessing cycles on the duodenoscope, showing that these may possibly make it susceptible to bacterial contamination and MDRO biofilm formation due to difficult reprocessing of the altered surfaces.