The first-generation anatomical medial meniscus prosthesis led to unsatisfactory results: a first-in-human study.

PURPOSE: The purpose of this first-in-human study was to evaluate the effect of a polycarbonate anatomical meniscus prosthesis system, including the surgical procedure, on knee pain and describe potential adverse events in patients with post-meniscectomy pain syndrome. METHODS: Eleven patients with post-meniscectomy pain syndrome and limited underlying cartilage damage were enrolled in the study. Five received a medial polycarbonate urethane meniscus prosthesis which was clicked onto 2 titanium screws fixated at the native horn attachments on the tibia. The KOOS score was planned to be collected at baseline and at 3, 6, 12 and 24 months following the intervention including radiographs at 6, 12 and 24 months. MRI scans were repeated after 12 and 24 months. RESULTS: The surgical technique to select an appropriately sized implant and correct positioning of the fixation screws and meniscus prosthesis onto the tibia was demonstrated to be feasible and reproducible. Inclusion stopped after 5 patients because of serious adverse device-related events. All patients reported knee joint stiffness and slight effusion in their knee at 6 months follow-up. In 3 patients the implant was removed because of implant failure and in 1 patient the implant was removed because of persistent pain and extension limitation. In none of the patients did the KOOS score improve in the first 6 months after surgery. However, in the patient who still has the implant in situ, PROMs started to improve 1 year after surgery and this improvement continued through 2 years of follow-up. The KOOS Pain, symptoms and ADL were close to the maximal 100 points. KOOS QoL and sport did improve but remained suboptimal. CONCLUSION: This first version of the meniscus prosthesis led to impaired knee function and failed in four out of five patients. The patients where the prosthesis was removed were salvable and the PROMs returned to pre-study levels. The results in the patient where the device is still in place are promising. LEVEL OF EVIDENCE: Level II.

The importance of continuous remnant preservation in anterior cruciate ligament reconstruction.

PURPOSE: Selective anteromedial or posterolateral bundle reconstruction is recognized as a treatment modality in partial anterior cruciate ligament (ACL) reconstruction (ACLR) with a biomechanically sufficient ACL remnant. However, there is paucity in literature investigating clinical outcomes of standard ACLR with preservation of residual continuous but biomechanically insufficient ACL tissue. The aim of this study was to investigate the influence of preservation of residual continuous but biomechanical insufficient ACL tissue in standard ACLR on complication and repeat surgery rate, and patient reported and clinical outcome. METHODS: The retrospective cohort comprised 134 patients (age 23 ± 7 years; Tegner 6 ± 3) with an isolated acute ACL tear. In 67 patients, residual continuous but biomechanically insufficient ACL tissue was present and preserved based on visual inspection, probing of the ACL tissue and Lachman test under arthroscopic view (standard reconstruction with tissue preservation; SRTP). These patients were matched to 67 patients that underwent ACLR where no residual ACL tissue could be preserved (standard reconstruction; SR) based on gender, age and chondral and/or meniscal status. Clinical failure (recurrent instability, pathological ACL graft laxity and/or ACL graft discontinuity), other complication and repeat-surgery rate within index surgery and 1-year and within index surgery and 2-year follow-up, and patient reported and clinical outcomes at 1-year and at 2-year follow-up were compared. RESULTS: A statistically significant lower clinical failure rate within index surgery and 1-year (SRTP, 3%; SR, 13%; P = 0.028) and within index surgery and 2-year follow-up (SRTP, 3%; SR, 23%; P = 0.001), and revision ACL surgery rate within index surgery and 1-year (SRTP, 2%; ST, 10%; P = 0.029) and within index surgery and 2-year follow-up (SRTP, 2%; SR, 18%; P = 0.001) was found in the SRTP group. No statistically significant differences were found for other investigated outcomes in patients that were without clinical failure. CONCLUSION: This study shows that in ACLR surgery, preservation of residual continuous but biomechanical insufficient ACL tissue might lead to lower clinical failure rate and ACL revision surgery rate within index surgery and 1-year, and within index surgery and 2-year follow-up compared to standard ACLR where no residual continuous ACL tissue could be preserved. LEVEL OF EVIDENCE: III.

Axial cortical involvement of metastatic lesions to identify impending femoral fractures; a clinical validation study.

BACKGROUND AND PURPOSE: Patients with advanced cancer may develop painful bone metastases, potentially resulting in pathological fractures. Adequate fracture risk assessment is of key importance to prevent fracturing and maintain mobility. This study aims to validate the clinical reliability of axial cortical involvement with a 30 mm threshold on conventional radiographs to assess fracture risk in femoral bone metastases. MATERIALS AND METHODS: All patients with bone metastases who received radiotherapy for pain included in two multicentre prospective studies were selected. Conventional radiographs obtained at a maximum of two months prior to radiotherapy were collected. Three experts independently measured lesions and scored radiographic characteristics. Sensitivity, specificity, positive (PPV) and negative predictive value (NPV) were calculated. RESULTS: Hundred patients were included with a median follow-up of 23.0 months (95%CI: 10.6-35.5). Two fractures occurred in lesions with axial cortical involvement <30 mm, and 12 in lesions ≥30 mm. Sensitivity, specificity, PPV and NPV of axial cortical involvement for predicting femoral fractures were 86%, 50%, 20% and 96%, respectively. Patients with lesions ≥30 mm had a 5.3 times higher fracture risk than patients with smaller lesions. CONCLUSION: Our validation study confirmed the use of 30 mm axial cortical involvement to assess fracture risk in femoral bone metastases. Until a more accurate and practically feasible method has been developed, this clinical parameter remains an easy method to assess femoral fracture risk to aid patients and clinicians to choose the optimal individual treatment modality.

Can patient-specific finite element models better predict fractures in metastatic bone disease than experienced clinicians?: Towards computational modelling in daily clinical practice.

OBJECTIVES: In this prospective cohort study, we investigated whether patient-specific finite element (FE) models can identify patients at risk of a pathological femoral fracture resulting from metastatic bone disease, and compared these FE predictions with clinical assessments by experienced clinicians. METHODS: A total of 39 patients with non-fractured femoral metastatic lesions who were irradiated for pain were included from three radiotherapy institutes. During follow-up, nine pathological fractures occurred in seven patients. Quantitative CT-based FE models were generated for all patients. Femoral failure load was calculated and compared between the fractured and non-fractured femurs. Due to inter-scanner differences, patients were analyzed separately for the three institutes. In addition, the FE-based predictions were compared with fracture risk assessments by experienced clinicians. RESULTS: In institute 1, median failure load was significantly lower for patients who sustained a fracture than for patients with no fractures. In institutes 2 and 3, the number of patients with a fracture was too low to make a clear distinction. Fracture locations were well predicted by the FE model when compared with post-fracture radiographs. The FE model was more accurate in identifying patients with a high fracture risk compared with experienced clinicians, with a sensitivity of 89% versus 0% to 33% for clinical assessments. Specificity was 79% for the FE models versus 84% to 95% for clinical assessments. CONCLUSION: FE models can be a valuable tool to improve clinical fracture risk predictions in metastatic bone disease. Future work in a larger patient population should confirm the higher predictive power of FE models compared with current clinical guidelines.Cite this article: F. Eggermont, L. C. Derikx, N. Verdonschot, I. C. M. van der Geest, M. A. A. de Jong, A. Snyers, Y. M. van der Linden, E. Tanck. Can patient-specific finite element models better predict fractures in metastatic bone disease than experienced clinicians? Towards computational modelling in daily clinical practice. Bone Joint Res 2018;7:430-439. DOI: 10.1302/2046-3758.76.BJR-2017-0325.R2.

Relaxation of the MCL after an Open-Wedge High Tibial Osteotomy results in decreasing contact pressures of the knee over time.

PURPOSE: The objective of this study was to investigate the effect of a medial open-wedge osteotomy (OWO) and the release of the superficial medial collateral ligament (MCL) on the tibiofemoral cartilage pressure, the MCL tension and the valgus laxity of the knee. METHODS: Seven fresh-frozen, human cadaveric knees were used. Medial and lateral mean contact pressure (CP), peak contact pressure (peakCP), and contact area (CA) were measured using a pressure-sensitive film (I-Scan; Tekscan, Boston, MA). The MCL tension was measured using a custom-made device. These measurements were continuously recorded for 5 min after an OWO of 10°. After the osteotomy, the valgus laxity was measured with a handheld Newtonmeter. For one knee, the measurements were continued for 24 h. At the end, a complete release of the superficial MCL was performed and the measurements were repeated at 10°. RESULTS: There was relaxation of the MCL after the osteotomy; the tension dropped in 5 min with 10.7% (mean difference 20.5 N (95% CI 16.1-24.9)), and in 24 h, the tension decreased by 24.2% (absolute difference 38.8 N) (one knee). After the osteotomy, the mean CP, peakCP and CA increased in the medial compartment (absolute difference 0.17 MPa (95% CI 0.14-0.20), 0.27 MPa (95% CI 0.24-0.30), 132.9mm2 (95% CI 67.7-198.2), respectively), and decreased in the lateral compartment (absolute difference 0.02 MPa (95% CI 0.03 -0.01), 0.08 MPa (95% CI 0.11 - 0.04), 47.0 mm2 (95% CI -105.8 to 11.8), respectively). Only after a release of the superficial MCL, the mean CP, peak CP and CA significantly decreased in the medial compartment (absolute difference 0.17, 0.27 MPa, 119.8 mm2, respectively), and increased in the lateral compartment (absolute difference 0.02, 0.11 MPa, 52.4 mm2, respectively). After the release of the superficial MCL, a mean increase of 7.9° [mean difference - 0.1° (95% CI -1.9 to 1.6)] of the valgus laxity was found. CONCLUSIONS: A release of the superficial MCL helps achieve the goal of reducing medial cartilage pressure in an OWO. There was considerable relaxation of the MCL after an OWO that resulted in a decrease of the mean CP in the medial and lateral compartments of the knee over time. However, cartilage pressure shifted from the medial to the lateral compartment only after release of the superficial MCL. The release of the superficial MCL caused a significant increase in the valgus laxity, which could influence stability after an OWO. LEVEL OF EVIDENCE: I.

Tibial component with and without stem extension in a trabecular metal cone construct.

PURPOSE: The purpose of this study was to investigate stability and strain distribution of a tibial plateau reconstruction with a trabecular metal cone while the tibial component is implanted with and without a stem, and whether prosthetic stability was influenced by bone mineral density. Trabecular metal cones are designed to fill up major bone defects in total knee arthroplasty. Tibial components can be implanted in combination with a stem, but it is unclear whether this is necessary after reconstruction with a trabecular metal cone. Implanting a stem can give extra stability, but may have negative side effects. METHODS: Tibial revision arthroplasties with trabecular metal cones were performed after reconstruction of a 2B bone defect according to the Anderson Orthopedic Research Institute classification. Components were implanted in seven pairs of cadaveric tibiae; one tibia of each pair was implanted with stem and the other without. All specimens were loaded to one bodyweight alternating between the medial and lateral tibial component. Implant-bone micro-motions, bone strains, bone mineral density and correlations were measured and/or calculated. RESULTS: Tibial components without a stem showed only more varus tilt [difference in median 0.14° (P < 0.05)], but this was not considered clinically relevant. Strain distribution did not differ. Bone mineral density only had an effect on the anterior/posterior tilt [ρ: -0.72 (P < 0.01)]. CONCLUSION: Tibial components, with or without a stem, which are implanted after reconstruction of major bone defects using trabecular metal cones produce very similar biomechanical conditions in terms of stability and strain distribution. If in vivo studies confirm that a stem extension is not mandatory, orthopaedic surgeons can decide not to implant a stem. LEVEL OF EVIDENCE: II.

Short-term clinical results of revision elbow arthroplasty using the Latitude total elbow arthroplasty.

AIMS: Revision total elbow arthroplasty (TEA) is often challenging. The aim of this study was to report on the clinical and radiological results of revision arthroplasty of the elbow with the Latitude TEA. PATIENTS AND METHODS: Between 2006 and 2010 we used the Latitude TEA for revision in 18 consecutive elbows (17 patients); mean age 53 years (28 to 80); 14 women. A Kudo TEA was revised in 15 elbows and a Souter-Strathclyde TEA in three. Stability, range of movement (ROM), visual analogue score (VAS) for pain and functional scores, Elbow Functional Assessment Scale (EFAS), the Functional Rating Index of Broberg and Morrey (FRIBM) and the Modified Andrews' Elbow Scoring System (MAESS) were assessed pre-operatively and at each post-operative follow-up visit (six, 12 months and biennially thereafter). Radiographs were analysed for loosening, fractures and dislocation. The mean follow-up was 59 months (26 to 89). RESULTS: The ROM of the elbow did not improve significantly. The mean EFAS and MAESS scores improved significantly six months post-operatively (18.6 points, standard deviation (sd) 7.7; p = 0.03 and 28.8 points, sd 8.6; p = 0.006, respectively) and continued to improve slightly or reached a plateau. The mean pain scores at rest (Z = -3.2, p = 0.001) and during activity (Z = -3.2, p = 0.001), and stability (Z = -3.0, p = 0.003) improved significantly six months post-operatively. Thereafter scores continued to improve slightly or a plateau was reached. There were no signs of loosening. CONCLUSION: Revision surgery using the Latitude TEA results in improvement of functionality, reduced pain and better stability of the elbow. Improvement of ROM of the elbow should not be expected. Cite this article: Bone Joint J 2016;98-B:1086-92.

Sensitivity of subject-specific models to Hill muscle-tendon model parameters in simulations of gait.

Subject-specific musculoskeletal (MS) models of the lower extremity are essential for applications such as predicting the effects of orthopedic surgery. We performed an extensive sensitivity analysis to assess the effects of potential errors in Hill muscle-tendon (MT) model parameters for each of the 56 MT parts contained in a state-of-the-art MS model. We used two metrics, namely a Local Sensitivity Index (LSI) and an Overall Sensitivity Index (OSI), to distinguish the effect of the perturbation on the predicted force produced by the perturbed MT parts and by all the remaining MT parts, respectively, during a simulated gait cycle. Results indicated that sensitivity of the model depended on the specific role of each MT part during gait, and not merely on its size and length. Tendon slack length was the most sensitive parameter, followed by maximal isometric muscle force and optimal muscle fiber length, while nominal pennation angle showed very low sensitivity. The highest sensitivity values were found for the MT parts that act as prime movers of gait (Soleus: average OSI=5.27%, Rectus Femoris: average OSI=4.47%, Gastrocnemius: average OSI=3.77%, Vastus Lateralis: average OSI=1.36%, Biceps Femoris Caput Longum: average OSI=1.06%) and hip stabilizers (Gluteus Medius: average OSI=3.10%, Obturator Internus: average OSI=1.96%, Gluteus Minimus: average OSI=1.40%, Piriformis: average OSI=0.98%), followed by the Peroneal muscles (average OSI=2.20%) and Tibialis Anterior (average OSI=1.78%) some of which were not included in previous sensitivity studies. Finally, the proposed priority list provides quantitative information to indicate which MT parts and which MT parameters should be estimated most accurately to create detailed and reliable subject-specific MS models.

Functional biomechanical performance of a novel anatomically shaped polycarbonate urethane total meniscus replacement.

PURPOSE: To evaluate the functional biomechanical performance of a novel anatomically shaped, polycarbonate urethane total meniscus implant. METHODS: Five human cadaveric knees were flexed between 0° and 90° under compressive loads mimicking a squat movement. Anteroposterior (AP) laxity tests were performed in 30° and 90° flexion. Meniscal kinematics and knee laxity were quantified using roentgen stereophotogrammetric analysis. Tibial cartilage contact mechanics were determined in 90° flexion. Measurements were repeated for the native medial meniscus, the implant, after total medial meniscectomy and allograft transplantation. RESULTS: The implant and allograft displayed increased posterior and medial displacements compared to the native meniscus, yet no differences were found between the implant and allograft. Meniscal condition did not affect rotational laxity. Compared to the native joint, AP laxity for the implant was increased in 30° flexion, but not in 90°. The implant reduced the mean contact pressure compared to meniscectomy but could not restore contact pressures to native meniscus levels. Compared to the native meniscus, the implant significantly increased the peak pressure, while the contact area was reduced. Contact mechanics of the implant and allograft were never statistically different. CONCLUSIONS: Biomechanical performance was similar for the implant and allograft. However, both meniscal replacements could not restore outcomes to native meniscus levels or sufficiently improve outcomes after meniscectomy. This was presumably caused by the mobility allowed by the suture-only horn fixation. The similarity of implant and allograft performance suggests that the novel implant has the biomechanical potential to serve as an alternative to meniscal allograft transplantation.

Acetabular revision with impaction bone grafting and a cemented polyethylene acetabular component: comparison of the Kaplan-Meier analysis to the competing risk analysis in 62 revisions with 25 to 30 years follow-up.

We present the results of 62 consecutive acetabular revisions using impaction bone grafting and a cemented polyethylene acetabular component in 58 patients (13 men and 45 women) after a mean follow-up of 27 years (25 to 30). All patients were prospectively followed. The mean age at revision was 59.2 years (23 to 82). We performed Kaplan-Meier (KM) analysis and also a Competing Risk (CR) analysis because with long-term follow-up, the presence of a competing event (i.e. death) prevents the occurrence of the endpoint of re-revision. A total of 48 patients (52 hips) had died or had been re-revised at final review in March 2011. None of the deaths were related to the surgery. The mean Harris hip score of the ten surviving hips in ten patients was 76 points (45 to 99). The KM survivorship at 25 years for the endpoint 're-revision for any reason' was 58.0% (95% confidence interval (CI) 38 to 73) and for 're-revision for aseptic loosening' 72.1% (95% CI 51 to 85). With the CR analysis we calculated the KM analysis overestimates the failure rate with respectively 74% and 93% for these endpoints. The current study shows that acetabular impaction bone grafting revisions provide good clinical results at over 25 years.

Short Term Evaluation of an Anatomically Shaped Polycarbonate Urethane Total Meniscus Replacement in a Goat Model.

PURPOSE: Since the treatment options for symptomatic total meniscectomy patients are still limited, an anatomically shaped, polycarbonate urethane (PCU), total meniscus replacement was developed. This study evaluates the in vivo performance of the implant in a goat model, with a specific focus on the implant location in the joint, geometrical integrity of the implant and the effect of the implant on synovial membrane and articular cartilage histopathological condition. METHODS: The right medial meniscus of seven Saanen goats was replaced by the implant. Sham surgery (transection of the MCL, arthrotomy and MCL suturing) was performed in six animals. The contralateral knee joints of both groups served as control groups. After three months follow-up the following aspects of implant performance were evaluated: implant position, implant deformation and the histopathological condition of the synovium and cartilage. RESULTS: Implant geometry was well maintained during the three month implantation period. No signs of PCU wear were found and the implant did not induce an inflammatory response in the knee joint. In all animals, implant fixation was compromised due to suture breakage, wear or elongation, likely causing the increase in extrusion observed in the implant group. Both the femoral cartilage and tibial cartilage in direct contact with the implant showed increased damage compared to the sham and sham-control groups. CONCLUSION: This study demonstrates that the novel, anatomically shaped PCU total meniscal replacement is biocompatible and resistant to three months of physiological loading. Failure of the fixation sutures may have increased implant mobility, which probably induced implant extrusion and potentially stimulated cartilage degeneration. Evidently, redesigning the fixation method is necessary. Future animal studies should evaluate the improved fixation method and compare implant performance to current treatment standards, such as allografts.

Mid-term clinical results of a modern convertible total elbow arthroplasty.

Unlinked, linked and convertible total elbow arthroplasties (TEAs) are currently available. This study is the first to report the clinical results of the convertible Latitude TEA. This was a retrospective study of a consecutive cohort of 63 patients (69 primary TEAs) with a mean age of 60 years (23 to 87). Between 2006 and 2008 a total of 19 men and 50 women underwent surgery. The mean follow-up was 43 months (8 to 84). The range of movement, function and pain all improved six months post-operatively and either continued to improve slightly or reached a plateau thereafter. The complication rate is similar to that reported for other TEA systems. No loosening was seen. Remarkable is the disengagement of the radial head component in 13 TEAs (31%) with a radial head component implanted. Implantation of both the linked and the unlinked versions of the Latitude TEA results in improvement of function and decreased pain, and shows high patient satisfaction at mid-term follow-up.

TLEM 2.0 - a comprehensive musculoskeletal geometry dataset for subject-specific modeling of lower extremity.

When analyzing complex biomechanical problems such as predicting the effects of orthopedic surgery, subject-specific musculoskeletal models are essential to achieve reliable predictions. The aim of this paper is to present the Twente Lower Extremity Model 2.0, a new comprehensive dataset of the musculoskeletal geometry of the lower extremity, which is based on medical imaging data and dissection performed on the right lower extremity of a fresh male cadaver. Bone, muscle and subcutaneous fat (including skin) volumes were segmented from computed tomography and magnetic resonance images scans. Inertial parameters were estimated from the image-based segmented volumes. A complete cadaver dissection was performed, in which bony landmarks, attachments sites and lines-of-action of 55 muscle actuators and 12 ligaments, bony wrapping surfaces, and joint geometry were measured. The obtained musculoskeletal geometry dataset was finally implemented in the AnyBody Modeling System (AnyBody Technology A/S, Aalborg, Denmark), resulting in a model consisting of 12 segments, 11 joints and 21 degrees of freedom, and including 166 muscle-tendon elements for each leg. The new TLEM 2.0 dataset was purposely built to be easily combined with novel image-based scaling techniques, such as bone surface morphing, muscle volume registration and muscle-tendon path identification, in order to obtain subject-specific musculoskeletal models in a quick and accurate way. The complete dataset, including CT and MRI scans and segmented volume and surfaces, is made available at http://www.utwente.nl/ctw/bw/research/projects/TLEMsafe for the biomechanical community, in order to accelerate the development and adoption of subject-specific models on large scale. TLEM 2.0 is freely shared for non-commercial use only, under acceptance of the TLEMsafe Research License Agreement.

Effect of medial-lateral malpositioning of the femoral component in total knee arthroplasty on anterior knee pain at greater than 8 years of follow-up.

BACKGROUND: The trochlea is often medialized after total knee arthroplasty (TKA) resulting in abnormal patellar tracking, which may lead to anterior knee pain. However, due to the difference in shape of the natural trochlea and the patellar groove of the femoral component, a medialization of the femoral component of 5 mm results in an equal patellar position at 0-30° of flexion. We tested the hypothesis that more medialization of the trochlea results in a higher VAS pain score and lower Kujala anterior knee pain score at midterm follow-up. METHODS: During surgery a special instrument was used to measure the mediolateral position of the natural trochlea and the prosthetic groove in 61 patients between 2004 and 2005. Patient reported outcome measures were used to investigate the clinical results (NRS-pain, NRS-satisfaction, KOOS-PS and Kujala knee score). RESULTS: In total 40 patients were included. The mean follow-up was 8.8 years. A medialization of ≥5 mm resulted in a significantly lower NRS-pain (0.2 vs. 1.4; p=0.004) and higher NRS-satisfaction (9.6 vs. 8.2; p=0.045). Overall clinical results were good; KOOS-PS was 33.9 and Kujala knee score was 72.1. CONCLUSIONS: The present study showed that a more medial position may result in a better postoperative outcome, which can probably be explained by the non-physiological lateral orientation of the trochlear groove in TKA designs. LEVEL OF EVIDENCE: Level III.

Accuracy of a computer-assisted planning and placement system for anatomical femoral tunnel positioning in anterior cruciate ligament reconstruction.

BACKGROUND: Femoral tunnel positioning is a difficult, but important factor in successful anterior cruciate ligament (ACL) reconstruction. Computer navigation can improve the anatomical planning procedure besides the tunnel placement procedure. METHODS: The accuracy of the computer-assisted femoral tunnel positioning method for anatomical double bundle ACL-reconstruction with a three-dimensional template was determined with respect to both aspects for AM and PL bundles in 12 cadaveric knees. RESULTS: The accuracy of the total tunnel positioning procedure was 2.7 mm (AM) and 3.2 mm (PL). These values consisted of the accuracies for planning (AM:2.9 mm; PL:3.2 mm) and for placement (about 0.4 mm). The template showed a systematic bias for the PL-position. CONCLUSIONS: The computer-assisted templating method showed high accuracy for tunnel placement and has promising capacity for application in anatomical tunnel planning. Improvement of the template will result in an accurate and robust navigation system for femoral tunnel positioning in ACL-reconstruction.

Sensitivity of subject-specific models to errors in musculo-skeletal geometry.

Subject-specific musculo-skeletal models of the lower extremity are an important tool for investigating various biomechanical problems, for instance the results of surgery such as joint replacements and tendon transfers. The aim of this study was to assess the potential effects of errors in musculo-skeletal geometry on subject-specific model results. We performed an extensive sensitivity analysis to quantify the effect of the perturbation of origin, insertion and via points of each of the 56 musculo-tendon parts contained in the model. We used two metrics, namely a Local Sensitivity Index (LSI) and an Overall Sensitivity Index (OSI), to distinguish the effect of the perturbation on the predicted force produced by only the perturbed musculo-tendon parts and by all the remaining musculo-tendon parts, respectively, during a simulated gait cycle. Results indicated that, for each musculo-tendon part, only two points show a significant sensitivity: its origin, or pseudo-origin, point and its insertion, or pseudo-insertion, point. The most sensitive points belong to those musculo-tendon parts that act as prime movers in the walking movement (insertion point of the Achilles Tendon: LSI=15.56%, OSI=7.17%; origin points of the Rectus Femoris: LSI=13.89%, OSI=2.44%) and as hip stabilizers (insertion points of the Gluteus Medius Anterior: LSI=17.92%, OSI=2.79%; insertion point of the Gluteus Minimus: LSI=21.71%, OSI=2.41%). The proposed priority list provides quantitative information to improve the predictive accuracy of subject-specific musculo-skeletal models.

The assessment of the risk of fracture in femora with metastatic lesions: comparing case-specific finite element analyses with predictions by clinical experts.

Previously, we showed that case-specific non-linear finite element (FE) models are better at predicting the load to failure of metastatic femora than experienced clinicians. In this study we improved our FE modelling and increased the number of femora and characteristics of the lesions. We retested the robustness of the FE predictions and assessed why clinicians have difficulty in estimating the load to failure of metastatic femora. A total of 20 femora with and without artificial metastases were mechanically loaded until failure. These experiments were simulated using case-specific FE models. Six clinicians ranked the femora on load to failure and reported their ranking strategies. The experimental load to failure for intact and metastatic femora was well predicted by the FE models (R(2) = 0.90 and R(2) = 0.93, respectively). Ranking metastatic femora on load to failure was well performed by the FE models (τ = 0.87), but not by the clinicians (0.11 < τ < 0.42). Both the FE models and the clinicians allowed for the characteristics of the lesions, but only the FE models incorporated the initial bone strength, which is essential for accurately predicting the risk of fracture. Accurate prediction of the risk of fracture should be made possible for clinicians by further developing FE models.

Computer-assisted anatomically placed double-bundle ACL reconstruction: an in vitro experiment with different tension angles for the AM and the PL graft.

Anterior cruciate ligament reconstruction techniques are evolving with innovations like double-bundle (DB) grafts and computer assistance. The current DB techniques do not appear to make the clinical difference yet. Insight in various techniques may lead to better results. In this study, the anterior laxity of a DB reconstruction with an anteromedial (AM) graft fixated in 90° of flexion and a posterolateral (PL) graft fixated in 20° and computer-assisted anatomically placed femoral attachments was compared to normal values and single-bundle grafts. In 8 fresh-frozen human cadaveric knees, the anterior laxity was tested from 0° to 90° flexion, with a 100 Newton (N) anterior tibial load in joints with (1) intact ACL, (2) torn ACL, (3) single-bundle (SB) graft tensed with 15 N in 20°, (4) anatomic AM graft tensed with 15 N in 90°, (5) anatomic PL graft tensed with 15 N in 20°, and (6) anatomic DB graft (4+5). All reconstructions caused a posterior position of the tibia. Relative to the normal anterior laxity, the single-bundle techniques showed significantly increased laxities: The SB technique in 0° (+1.1 mm) and 15° (+1.7 mm); The AM reconstructions in 45° (+1.6 mm) and 90° (+1.5 mm); The PL reconstructions in all angles (from +1.4 to +2.3 mm), except in 0°. The anatomic DB technique showed no significantly increased laxities and restored normal laxity in all angles.

BMP-7 stimulates early diaphyseal fracture healing in estrogen deficient rats.

Estrogen deficiency causes postmenopausal osteoporosis. The relationship between estrogen deficiency and the high failure rate after osteoporotic fracture treatment is unclear, as is the effect of possible interventions, either with anti-resorptive agents or with anabolic agents such as bone morphogenetic proteins (BMPs). To investigate the influence of estrogen deficiency as well as the effect of early intervention, forty female wistar rats underwent ovarectomy (OVX) followed by low calcium diet. Ten rats underwent sham operations, followed by normal diet. After 6 weeks, a closed midshaft femoral fracture was induced. Ten animals received a systemic bisphosphonate injection, 10 injection of BMP-7 in the fracture, and 10 a combination. All then received a normal diet. After 2 weeks healing was evaluated using radiographs, CT, biomechanical testing, and histology. Radiography showed significant increase of bridging in groups treated with BMP-7. Callus volume was higher in these groups. Bending stiffness and strength were similar between OVX and sham, and not influenced by bisphosphonates. Significant increase was seen in groups treated with BMP-7. Histology was in accordance with other endpoints. Early fracture healing was not affected by estrogen deficiency. While no beneficiary effect of bisphosphonate treatment was found, injection of BMP-7 stimulated healing in ovarectomized rats.