RESUMO
Radiographs are commonly used to assess articular reduction of the distal tibia (pilon) fractures postoperatively, but may reveal malreductions inaccurately. While magnetic resonance imaging (MRI) and computed tomography (CT) are potential three-dimensional (3D) alternatives they generate metal-related artifacts. This study aims to quantify the artifact size from orthopaedic screws using CT, 1.5T and 3T MRI data. Three screws were inserted into one intact human cadaver ankle specimen proximal to and along the distal articular surface, then CT, 1.5T and 3T MRI scanned. Four types of screws were investigated: titanium alloy (TA), stainless steel (SS) (Ø =3.5 mm), cannulated TA (CTA) and cannulated SS (CSS) (Ø =4.0 mm, Ø empty core =2.6 mm). 3D artifact models were reconstructed using adaptive thresholding. The artifact size was measured by calculating the perpendicular distance from the central screw axis to the boundary of the artifact in four anatomical directions with respect to the distal tibia. The artifact sizes (in the order of TA, SS, CTA and CSS) from CT were 2.0, 2.6, 1.6 and 2.0 mm; from 1.5T MRI they were 3.7, 10.9, 2.9, and 9 mm; and 3T MRI they were 4.4, 15.3, 3.8, and 11.6 mm respectively. Therefore, CT can be used as long as the screws are at a safe distance of about 2 mm from the articular surface. MRI can be used if the screws are at least 3 mm away from the articular surface except for SS and CSS. Artifacts from steel screws were too large thus obstructed the pilon from being visualised in MRI. Significant differences (P<0.05) were found in the size of artifacts between all imaging modalities, screw types and material types, except 1.5T versus 3T MRI for the SS screws (P=0.063). CTA screws near the joint surface can improve postoperative assessment in CT and MRI. MRI presents a favourable non-ionising alternative when using titanium hardware. Since these factors may influence the quality of postoperative assessment, potential improvements in operative techniques should be considered.
RESUMO
BACKGROUND/AIMS: Currently the diagnosis and severity of hepatic steatosis can be established accurately only by liver biopsy. Previous small studies found that steatosis measured by magnetic resonance spectroscopy (MRS) and imaging (MRI) correlated with histological assessment of liver triglyceride content. However, the accuracy of MRS/MRI for grading the severity of steatosis has not been addressed. The aims of this study were (1) to determine whether MRS and MRI can discriminate grades of steatosis in a large cohort of consecutive patients with a wide spectrum of liver disease aetiology and severity (2) to evaluate the effect of hepatic fibrosis, inflammation and iron on quantitation of intrahepatocellular lipid (IHCL) by these techniques. METHODS: Ninety-four sequential patients who underwent percutaneous liver biopsy or liver resection had MRS and MRI (Dixon in phase/out of phase (Dixon IP/OP) and with/without fat saturation (+/-FS) images) to determine IHCL. Histology was used as the reference standard. RESULTS: Close relationships were observed between the percentage of steatosis estimated by histology and MRS/MRI (r(s)=0.88 p<0.001 for all techniques). However, separate equations were required for the percentage of steatosis to avoid underestimation by imaging for patients with moderate or advanced fibrosis. All techniques had good diagnostic accuracy for mild steatosis (AUROC > or =0.87) as well as moderate/severe steatosis (AUROC > or =0.89). Hepatic inflammation and mild iron deposition (Perls' grade 1 and 2) did not interfere with estimation of steatosis by imaging. CONCLUSIONS: MRS and MRI had good accuracy for grading the severity of steatosis in subjects with liver disease, provided that stage of fibrosis was considered.