The Effect of the Displacement Amplitude on the Fretting Wear of GCr15 Steel with a TiC Coating.

In the present paper, the effect of mechanical ball milling time on the fretting wear of GCr15 steel balls at different displacement amplitudes is investigated. TiC powder coating was fabricated on the surface of GCr15 steel balls using various process times, and the fretting wear tests were conducted on an AISI 52100 steel disk with the applied force of 80 N. Additionally, various displacement amplitudes (10 µm, 20 µm, and 60 µm) were selected. Specimen attributes and wear scars were characterized using an inverted metallographic microscope, a microhardness tester, an X-ray diffractometry analyzer, a white light interferometer, and a scanning electron microscope. The results showed that thick and continuous coatings could be obtained at the milling time of 18 h. The specimens processed for a longer milling time demonstrated better fretting wear resistance, which we attribute to higher microhardness of the surface layer. The coefficient of friction and wear volume of specimens at each different displacement amplitude significantly decreased with increasing milling time. As the displacement amplitude increased, the three fretting states were: partial slip coordinated by elastic deformation; partial slip state coordinated by plastic deformation; and gross slip condition. Our observations indicate that mechanical ball milling could be an efficient approach to improve the fretting wear resistance of GCr15 steel balls.

Enhanced Strength-Ductility Synergy Properties in Selective Laser Melted 316L Stainless Steel by Strengthening Grinding Process.

Selective laser melted (SLM) 316L stainless steel (SS) has been widely employed in the fields of designing and manufacturing components with complex shapes and sizes. However, the low yield strength, low ultimate tensile stress, and low hardness of SLM 316L SS components hinder its further application. In this work, the strengthening grinding process (SGP) was used to enhance the mechanical properties of SLM 316L SS. The microhardness, residual stress, microstructure, and tensile properties of all the samples were analyzed. The results demonstrate that the SGP induced higher compressive residual stress and microhardness, as well as higher tensile properties. The maximum hardness and residual stress reached 354.5 HV and -446 MPa, respectively, indicating that the SGP resulted in a plastic deformation layer over 150 µm. The possible mechanisms have been discussed in further detail. Compared to the untreated sample, the SGP sample shows a significant improvement in yield strength (YS), ultimate tensile stress (UTS), and elongation (EL), increasing 30%, 25.5%, and 99.1%, respectively. This work demonstrates that SGP treatment could be an efficient approach to simultaneously improving the strength and ductility of the SLM 316L SS, which makes it more suitable for engineering applications.

"Stomach mass" as the first manifestation of IgG4-related disease: a case report.

BACKGROUND: IgG4-related disease mainly manifests as organomegaly and is accompanied by tissue fibrosis (Mimori, Mod Rheumatol 29(2):213, 2019) which is frequently confused with tumour (Dawei et al., J Gastroenterol Hepatol 29(12):1375-8, 2020). There are few reports with of IgG4-related disease with the first clinical manifestation involving the stomach. CASE PRESENTATION: We present the case of 46-year-old male patient with a "stomach tumour" as the first manifestation of IgG4-related disease. Gastroscopy showed a mass in the stomach, however, the pathology result was chronic inflammation with IgG4 positivity. CT scans of abdomen showed that the stomach wall was thick, the head of the pancreas was swollen, and retroperitoneal fibrosis was severe.The serum IgG4 level was 75 g/L (normal range 0.03-2.01 g/L).After treatment with methylprednisolone for one month, the symptoms were greatly relieved. CONCLUSIONS: To reduce the suffering of patients and relieve their financial burden, we should consider the possibility of IgG4-related disease when the initial manifestation is a stomach mass.

Changes in composition and enamel demineralization inhibition activities of gallic acid at different pH values.

BACKGROUND: Gallic acid (GA) has been shown to inhibit demineralization and enhance remineralization of enamel; however, GA solution is highly acidic. This study was to investigate the stability of GA solutions at various pH and to examine the resultant effects on enamel demineralization. METHODS: The stability of GA in H2O or in phosphate buffer at pH 5.5, pH 7.0 and pH 10.0 was evaluated qualitatively by ultraviolet absorption spectra and quantified by high performance liquid chromatography with diode array detection (HPLC-DAD). Then, bovine enamel blocks were subjected to a pH-cycling regime of 12 cycles. Each cycle included 5 min applications with one of the following treatments: 1 g/L NaF (positive control), 4 g/L GA in H2O or buffered at pH 5.5, pH 7.0 and pH 10.0 and buffers without GA at the same pH (negative control), followed by a 60 min application with pH 5.0 acidic buffers and a 5 min application with neutral buffers. The acidic buffers were analysed for dissolved calcium. RESULTS: GA was stable in pure water and acidic condition, but was unstable in neutral and alkaline conditions, in which ultraviolet spectra changed and HPLC-DAD analysis revealed that most of the GA was degraded. All the GA groups significantly inhibited demineralization (p < 0.05) and there was no significant difference of the inhibition efficacy among different GA groups (p > 0.05). CONCLUSIONS: GA could inhibit enamel demineralization and the inhibition effect is not influenced by pH. GA could be a useful source as an anti-cariogenic agent for broad practical application.