High-Temperature Compression Behaviors and Constitutive Models of a 7046-Aluminum Alloy.

High-temperature forming behaviors of a 7046-aluminum alloy were investigated by hot compression experiments. The microstructural evolution features with the changes in deformation parameters were dissected. Results indicated the formation of massive dislocation clusters/cells and subgrains through the intense DRV mechanism at low compression temperature. With an increase in deformation temperature, the annihilation of dislocations and the coarsening of subgrains/DRX grains became prominent, due to the collaborative effects of the DRV and DRX mechanisms. However, the growth of subgrains and DRX grains displayed the weakening trend at high strain rates. Moreover, two constitutive models involving a physically based (PB) model and a gate recurrent unit (GRU) model were proposed for predicting the hot compression features. By validation analysis, the predicted values of true stress perfectly fit with the experimental data, indicating that both the proposed PB model and the GRU model can accurately predict the hot compression behaviors of 7046-aluminum alloys.

The Mechanism of Dendrite Formation in a Solid-State Transformation of High Aluminum Fe-Al Alloys.

The mechanism of solid-state dendrite formation in high-aluminum Fe-Al alloys is not clear. Applying an in-situ observation technique, the real-time formation and growth of FeAl solid-state dendrites during the eutectoid decomposition of the high-temperature phase Fe5Al8 is visualized. In-situ experiments by HT-CSLM reveal that proeutectoid FeAl usually does not preferentially nucleate at grain boundaries regardless of rapid or slow cooling conditions. The critical radii for generating morphological instability are 1.2 µm and 0.9 µm for slow and rapid cooling, respectively. The morphology after both slow and rapid cooling exhibits dendrites, while there are differences in the size and critical instability radius Rc, which are attributed to the different supersaturation S and the number of protrusions l. The combination of crystallographic and thermodynamic analysis indicates that solid-state dendrites only exist on the hypoeutectoid side in high-aluminum Fe-Al alloys. A large number of lattice defects in the parent phase provides an additional driving force for nucleation, leading to coherent nucleation from the interior of the parent phase grains based on the orientation relationship {3¯30}Fe5Al8//{1¯10}FeAl, <111¯>Fe5Al8//<111¯>FeAl. The maximum release of misfit strain energy leads to the preferential growth of the primary arm of the nucleus along <111¯> {1¯10}. During the rapid cooling process, a large supersaturation is induced in the matrix, driving the Al atoms to undergo unstable uphill diffusion and causing variations in the concentration gradient as well as generating constitutional undercooling, ultimately leading to morphological instability and the growth of secondary arms.

A New Strategy on Designing Fluxes for Aluminum Alloy Melt Refinement.

With the aim of obtaining a refining flux that is stable and provides effective refining of aluminum melt, a new strategy of designing the flux composition has been proposed. Ten fluxes were designed, by selecting ten molten salt compounds according to their thermophysical parameters, physical properties, and thermodynamic analysis. The melting points of the ten fluxes, and the phases transformation of the fluxes after melting, were studied by DSC and XRD, respectively. The contact angles between four groups of fluxes and alumina at refinement temperatures were studied, and the effect of refinement was characterized by a metallographic microscope. The process of the fluxes removing inclusions and degassing was analyzed thermodynamically. The research findings indicate that flux #10 (11.0 wt.%NaF, 29.5 wt.%NaCl, 46.5 wt.%Na2CO3, 3.0 wt.%CaF2, 10.0 wt.%Na3AlF6) has a melting point (562.2 °C) below the refining temperature. At the refining temperature (760 °C), flux #10 has the lowest contact angle, of 12.78°. In addition, compared to that of flux STJ-A3, currently used in practice, flux #10 has a better refining effectiveness, with the pores and inclusions content of the sample being reduced to 1.11% from 2.96%.

Inhomogeneous Microstructure Evolution of 6061 Aluminum Alloyat High Rotating Speed Submerged Friction Stir Processing.

An inhomogeneous microstructure induced by high rotating speed submerged friction stir processing (HRS-SFSP) on 6061 aluminum alloy was researched in detail.The microstructures of the aluminum alloy processing zone were characterized by electron backscattered diffraction (EBSD) and transmission electron microscope (TEM) qualitatively and quantitatively.The results show that the recrystallization proportion in the inhomogeneous structure of the processing zone is 14.3%, 37.8% and 35.9%, respectively. Different degrees of grain deformation can affect the dislocation and lead to the formation of a plastic-elastic interface. At the same time, the second-phase particles in the processing zone were inhomogeneity and relatively, which further promotes the plastic-elastic interface effect. The plastic-elastic interface can significantly improve the strength of aluminum alloy, whileat the same time, rely on recrystallized grains to provide enough plasticity. When the rotation speed was 3600 r/min, the strength and ductility of the aluminum alloy after HRS-SFSP were increased by 48.7% and 10.2% respectively compared with that of BM. In all, the plastic-elastic interface can be formed by using high rotating speed submerged friction stir processing, and the strength-ductility synergy of aluminum alloy can be realized at the plastic-elastic interface.