RESUMO
Ternary composite with great modulation of electron transfers has attracted a lot of attention from the field of high-performance room-temperature (RT) gas sensing. Herein, walnut-like WO3-Ni-graphene ternary composites were successfully synthesized by the hydrothermal method for formaldehyde (HCHO) sensing at RT. The structural and morphological analyses were carried out by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). SEM and TEM studies confirmed that walnut-like WO3 nanostructures with an average size of 53 ± 23 nm were functionalized. The Raman and XPS results revealed that, due to the deformation of the O-W-O lattice, surface oxygen vacancies Ov and surface-adsorbed oxygen species Oc were present. The gas-sensing measurement shows that the response of the WO3-Ni-Gr composite (86.8%) was higher than that of the Ni-Gr composite (22.7%) for 500 ppm HCHO at RT. Gas-sensing enhancement can be attributed to a p-n heterojunction formation between WO3 and Ni-Gr, Oc, spill-over effect of Ni decoration, and a special walnut-like structure. Moreover, long term stability (%R = 61.41 ± 1.66) for 30 days and high selectivity in the presence of other gases against HCHO suggested that the proposed sensor could be an ideal candidate for future commercial HCHO-sensing in a real environment.
RESUMO
Dioxins in the sintering flue gas are usually removed through integrated elimination technologies by carbonaceous catalysts. However, the regeneration of the used catalyst is poorly investigated, leading to the risk of leakage of dioxins. Herein, the influences of cyclic regenerations on the dioxin removal performance of a catalyst (V2O5/AC) were investigated systematically with dibenzofuran (DBF) as a model pollutant. It was demonstrated that the adsorption capacity and oxidation activity of catalysts significantly declined after several regeneration cycles due to the decreasing external specific surface area and V5+, respectively. Compared with 79.12% DBF directly emitted from a regenerator during N2 regeneration, the emission of DBF was only 29.93% with the modification of the regeneration process through O2 addition and temperature adjustment. The possible regenerated products were also analyzed to disclose the transformation behaviors of DBF. The regeneration mechanisms of DBF followed the transformation pathway of dibenzofuranol, benzofuran, anhydride species, and ultimately to CO2 and H2O. Moreover, the accumulated heavy aromatics on the surface could be decomposed by introducing O2. This research provides a comprehensive understanding of dioxin transformation behavior and a theoretical basis for efficient control of dioxin removal in the whole integrated removal technologies.
Assuntos
Dioxinas , Dibenzodioxinas Policloradas , Adsorção , Catálise , TemperaturaRESUMO
As formaldehyde is an extremely toxic volatile organic pollutant, a highly sensitive and selective gas sensor for low-concentration formaldehyde monitoring is of great importance. Herein, metal-organic framework (MOF) derived Pd/PdO@ZnO porous nanostructures were synthesized through hydrothermal method followed by calcination processes. Specifically, porous Pd/PdO@ZnO nanomaterials with large surfaces were synthesized using MOFs as sacrificial templates. During the calcination procedure, an optimized temperature of 500°C was used to form a stable structure. More importantly, intensive PdO@ZnO inside the material and composite interface provides lots of p-n heterojunction to efficiently manipulate room temperature sensing performance. As the height of the energy barrier at the junction of PdO@ZnO exponentially influences the sensor resistance, the Pd/PdO@ZnO nanomaterials exhibit high sensitivity (38.57% for 100 ppm) at room temperature for 1-ppm formaldehyde with satisfactory selectivity towards (ammonia, acetone, methanol, and IPA). Besides, due to the catalytic effect of Pd and PdO, the adsorption and desorption of the gas molecules are accelerated, and the response and recovery time is as small as 256 and 264 s, respectively. Therefore, this MOF-driven strategy can prepare metal oxide composites with high surface area, well-defined morphology, and satisfactory room-temperature formaldehyde gas sensing performance for indoor air quality control.
RESUMO
A non-diaphragm fiber gas pressure sensor based on a multimode interferometer (MI) using a hollow-core tube lattice fiber (HC-TLF) as a gas cell is proposed and experimentally demonstrated. The sensor is fabricated by fusion splicing a sandwich structure of a graded-index multimode fiber, HC-TLF, and lead-in/out single mode fiber. Several side-holes are drilled by using a femtosecond laser on the side wall of the HC-TLF to allow gas in and out of the fiber. The positions of side-hole in HC-TLF have been investigated during the experiments, which indicate that the highest gas pressure sensitivity existed as the side-hole located in the gap between adjacent cladding holes of the HC-TLF. The proposed structure exhibits a high sensitivity of 8.1 nm/MPa with the average gas fill time of 2.2 s. This sensor also has low temperature sensitivity and low temperature cross sensitivity of 12.3 pm/°C and 1.5 kPa/°C as the temperature rises to 400°C. In addition, the advantages of the gas pressure sensor, such as small size, rapid response, low temperature cross sensitivity, and simple fabrication process, make it suitable for high-pressure measurement in harsh conditions, e.g., downhole and ocean bottom.
RESUMO
Taxane-based chemotherapy-loaded drug delivery systems have great potential for cancer treatment. The docetaxel (DTX)-loaded PAMAM-based poly (γ-benzyl-l-glutamate)-b-d-α-tocopheryl polyethylene glycol 1000 succinate (PAM-PBLG-b-TPGS) nanoparticles and the docetaxel (DTX)-loaded PAMAM-based poly (γ-benzyl-l-glutamate) (PAM-PBLG) nanoparticles were designed using a modified nanoprecipitation method. The particle size, encapsulation efficiency (EE), and in vitro release characteristics of the nanoparticles were tested. The effects of the two nanoparticles on the cellular uptake and cell viability on human cervical cancer cell line Hela and the human breast cancer cell line MCF-7 were compared. Furthermore, their antitumor efficiency was evaluated through in vivo tumour growth experiment in comparison with free DTX. PAM-PBLG-b-TPGS nanoparticles displayed high EE, smaller diameter, and a nice releasing profile. Besides, based on the high EE and 'self-controlled' drug release of the DTX-loaded PAM-PBLG-b-TPGS nanoparticles, they exhibited stronger cytotoxicity (lower survival rate) and higher uptake rate than DTX-loaded PAM-PBLG nanoparticles in Hela cells and MCF-7 cells. Furthermore, compared with DTX-loaded PAM-PBLG nanoparticles and free DTX, DTX-loaded PAM-PBLG-b-TPGS nanoparticles produced a potent anti-tumour effect. Thus, the DTX-loaded PAM-PBLG-b-TPGS nanoparticles provide a novel attractive nanocarrier for the DTX delivery of chemotherapy to human breast cancer cells and human cervical cancer cells.