Numerical investigation of fluid flow behavior in steel cord with lattice Boltzmann methodology: The impacts of microstructure and loading force.

Steel cord materials were found to have internal porous microstructures and complex fluid flow properties. However, current studies have rarely reported the transport behavior of steel cord materials from a microscopic viewpoint. The computed tomography (CT) scanning technology and lattice Boltzmann method (LBM) were used in this study to reconstruct and compare the real three-dimensional (3D) pore structures and fluid flow in the original and tensile (by loading 800 N force) steel cord samples. The pore-scale LBM results showed that fluid velocities increased as displacement differential pressure increased in both the original and tensile steel cord samples, but with two different critical values of 3.3273 Pa and 2.6122 Pa, respectively. The original steel cord sample had higher maximal and average seepage velocities at the 1/2 sections of 3D construction images than the tensile steel cord sample. These phenomena should be attributed to the fact that when the original steel cord sample was stretched, its porosity decreased, pore radius increased, flow channel connectivity improved, and thus flow velocity increased. Moreover, when the internal porosity of tensile steel cord sample was increased by 1 time, lead the maximum velocity to increase by 1.52 times, and the average velocity was increased by 1.66 times. Furthermore, when the density range was determined to be 0-38, the pore phase showed the best consistency with the segmentation area. Depending on the Zou-He Boundary and Regularized Boundary, the relative error of simulated average velocities was only 0.2602 percent.

Effects of hydrogen permeation on the mechanical characteristics of electroless nickel-plated free-cutting steel for application to the hydrogen valves of hydrogen fuel cell electric vehicles.

Electroless nickel plating is a suitable technology for the hydrogen industry because electroless nickel can be mass-produced at a low cost. Investigating in a complex environment where hydrogen permeation and friction/wear work simultaneously is necessary to apply it to hydrogen valves for hydrogen fuel cell vehicles. In this research, the effects of hydrogen permeation on the mechanical characteristics of electroless nickel-plated free-cutting steel (SUM 24L) were investigated. Due to the inherent characteristics of electroless nickel plating, the damage (cracks and delamination of grain) and micro-particles by hydrogen permeation were clearly observed at the grain boundaries and triple junctions. In particular, the cracks grew from grain boundary toward the intergranualr. This is because the grain boundaries and triple junctions are hydrogen permeation pathways and increasing area of the hydrogen partial pressure. As a result, its surface roughness increased by a maximum of two times, and its hardness and adhesion strength decreased by hydrogen permeation. In particular, hydrogen permeation increased the friction coefficient of the electroless nickel-plated layer, and the damage caused by adhesive wear was significantly greater, increasing the wear depth by up to 5.7 times. This is believed to be due to the decreasing in wear resistance of the electroless nickel plating layer damaged by hydrogen permeation. Nevertheless, the Vickers hardness and the friction coefficient of the electroless nickel plating layer were improved by about 3 and 5.6 times, respectively, compared with those of the free-cutting steel. In particular, the electroless nickel-plated specimens with hydrogen embrittlement exhibited significantly better mechanical characteristics and wear resistance than the free-cutting steel.

Using native plants to evaluate urban metal pollution and appoint emission sources in the Brazilian Steel Valley region.

In southeastern Brazil, the city of Ipatinga is inserted in the Steel Valley Metropolitan Region, which hosts the largest industrial complex for flat-steel production in Latin America, while also having one of the largest vehicle fleets in the entire country. Since potentially toxic elements (PTEs) are not emitted solely by industries, yet also by vehicular activity, the predominant emission source can be determined by evaluating the ratio between different elements, which are called technogenic tracers. We performed a biomonitoring assay using two tropical legumes, Paubrasilia echinata and Libidibia ferrea var. leiostachya, aiming to assess chemical markers for the origin of emissions in the region, distinguishing between different anthropogenic sources. Plants were exposed for 90 days in four urban sites and in a neighboring park which served as reference. After the experimental period, plants were evaluated for trace-metal accumulation. L. ferrea var. leiostachya retained lower amounts of metals associated with vehicular and industrial emission. The opposite was found with P. echinata, a species which should be recommended for biomonitoring of air pollution as a bioaccumulator. Plants of P. echinata were enriched with Fe, Al, Ni, Cr, and Ba, whereas plants of L. ferrea var. leiostachya were enriched with Fe, Cu, and Co. In both species, Fe was the element with which plants were enriched the most. Plants showed highest iron enrichment at Bom Retiro, the site downwind to the steel industry, which has shown to be the main particle emission source in the region.

[Comparative study of minimally invasive titanium elastic nail and steel plate on the treatment of fracture of tibiofibular fracture in adults].

OBJECTIVE: To compare the clinical outcomes of using elastic intramedullary nail and plate to fix fibular fracture. METHODS: The 60 patients with tibiofibular fractures admitted from January 2015 to December 2022 were divided into two groups:intramedullary nail group and plate group, 30 cases each, intramedullary nail group was treated with elastic intramedullary nail fixation group, plate group was treated with steel plate and screw fixation group. Intramedullary nail group, there were 18 males and 12 females, aged from 22 to 75 years old with an average of (39.4±9.8) years old, including 24 cases of traffic accidents injury, 6 cases of falling injury, 23 cases of closed fractures, 7 cases of open fractures. Steel plate group, there were 15 males and 15 females, aged from 24 to 78 years old with an average of (38.6±10.2) years old. The 22 cases were injured by traffic accident, 8 cases were injured by falling. The 24 cases were closed fractures and 6 cases were open fractures. The operation time, intraoperative bleeding, American Orthopedic Foot and Ankle Society (AOFAS) ankle and hind foot scores, clinical healing time of fibula and the incidence of wound complications were compared between the two groups. RESULTS: The patients in both groups were followed up for 6 to 21 months, with an average of (14.0±2.8) months. Compared with plate group, intramedullary nail group had shorter operative time, less bleeding, shorter clinical healing time of fibula, and lower infection rate of incision, and the difference was statistically significant (P<0.05). There were 2 cases of delayed healing in intramedullary nail group, 1 case of nonunion in plate group, and 2 cases of delayed healing in plate group, and there was no statistically significant difference between the two groups (P>0.05). In the last follow-up, according to the AOFAS scoring standard, the ankle function in intramedullary nail group was excellent in 17 cases, good in 12 cases, fair in 1 case, with an average of (88.33±4.57) points, while in plate group, excellent in 16 cases, good in 10 cases, fair in 4 cases, with an average of (87.00±4.14) points;There was no statistical difference between the two groups (P>0.05). CONCLUSION: Elastic intramedullary nail has the advantages of short operation time, less intraoperative bleeding, short fracture healing time and less incision complications in the treatment of fibular fracture, which is worthy of clinical application.

A Comprehensive Evaluation of Dioxins and Furans Occurrence in River Sediments from a Secondary Steel Recycling Craft Village in Northern Vietnam.

This first study investigated the presence of dioxins and furans in river sediments around a craft village in Vietnam, focusing on Secondary Steel Recycling. Sediment samples were collected from various locations along the riverbed near the Da Hoi Secondary Steel Recycling village in Bac Ninh province. The analysis was conducted using a HRGC/HRMS-DFS device, detecting a total of 17 dioxin/furan isomers in all samples, with an average total concentration of 288.86 ng/kg d.w. The concentrations of dioxin/furan congeners showed minimal variation among sediment samples, ranging from 253.9 to 344.2 ng/kg d.w. The predominant compounds in the dioxin group were OCDD, while in the furan group, they were 1,2,3,4,6,7,8-HpCDF and OCDF. The chlorine content in the molecule appeared to be closely related to the concentration of dioxins and their percentage distribution. However, the levels of furan isomers did not vary significantly. The distribution of these compounds was not dependent on the flow direction, as they were mainly found in solid waste and are not water-soluble. Although the hepta and octa congeners had high concentrations, when converted to TEQ values, the tetra and penta groups (for dioxins) and the penta and hexa groups (for furans) contributed more to toxicity. Furthermore, the source of dioxins in sediments at Da Hoi does not only originate from steel recycling production activities but also from other combustion sites. The average total toxicity was 10.92 ng TEQ/kg d.w, ranging from 4.99 to 17.88 ng TEQ/kg d.w, which did not exceed the threshold specified in QCVN 43:2017/BTNMT, the National Technical Regulation on Sediment Quality. Nonetheless, these levels are still concerning. The presence of these toxic substances not only impacts aquatic organisms in the sampled water environment but also poses potential health risks to residents living nearby.

Mechanistic study on the promotion of Ca2+ leaching in steel slag through high-temperature solid waste modification.

Indirect carbonation of steel slag is an effective method for CO2 storage, reducing emissions, and promoting cleaner production in the steel industry. However, challenges remain, such as low Ca2+ leaching rates and slag management complexities arising from variations in mineral compositions. To address this, a high-temperature modification process is proposed to alter the mineral composition and facilitate the synergistic utilization of calcium and iron. This study delves into the effects of various solid waste modifications on the leaching of Ca2+ and the total iron content within steel slag. Results show that high-basicity modified slag forms Ca2(Al, Fe)2O5, reducing calcium leaching. Low-alkalinity modified slag produces calcium-rich aluminum minerals and also reduces the leaching of Ca2+ ions. At a basicity of 2.5, coal gangue, fly ash, and blast slag achieve maximum Ca2+ leaching rates of 88.93%, 89.46%, and 90.17%, respectively, with corresponding total iron contents of 41.46%, 37.72%, and 35.29%. Upgraded coal gangue exhibits a 50.02% increase in calcium leaching and a 15.58% increase in total iron content compared to the original slag. This enhances CO2 fixation and iron resource utilization. Overall, the proposed indirect carbonation and iron enrichment modification offer a novel approach for the resource utilization and environmental stability of steel slag.

Creating safety amidst chronic contamination: A mixed-method analysis of residents' experiences in a Southern Italian steel town.

This study analyses how residents create safety in Taranto, Italy, a city located next to one of the largest steel plants in Europe. Combining long-term ethnographic research with an online-based survey, our study shows that most respondents recognise and criticise the presence of environmental risks in their daily lives but encounter such risks in complex ways. Contrary to previous scholarship suggesting that pollution can result in alienating residents from their lived environment, this research shows that acute awareness of environmental risks does not necessarily undermine attachment to place but rather can co-exist with or even strengthen it. Our findings propose first that residents experience and understand environmental risk mostly through air pollution, but often situate risks outside of their own neighbourhood and inscribe different meanings to such risk. Second, residents mitigate environmental risk through practices aimed at creating safety, such as moving away from the industrial area or using everyday practices and reflecting on their responsibility for actions. Third, we argue that residents create safety through an attachment and entitlement to place and emotional detachment from pollution and institutional failures. Finally, in line with residents' concerns about safety and how to secure it, this study embraces a shift in its analytical focus from risk to the quest for safety. By doing so, it provides novel insights into environmental risk perception in industrially polluted areas and reveals the often-contradictory sentiments and practices that such areas invoke in residents.

Zwitterion modified chitosan as a high-performance corrosion inhibitor for mild steel in hydrochloric acid solution.

Herein, a novel chitosan Schiff base (CS-FGA) as a sustainable corrosion inhibitor has been successfully synthesized via a simple amidation reaction by using an imidazolium zwitterion and chitosan (CS). The corrosion inhibition property of CS-FGA for mild steel (MS) in a 1.0 M HCl solution was studied by various electrochemical tests and physical characterization methods. The findings indicate that the maximum inhibition efficiency of CS-FGA as a mixed-type inhibitor for MS in 1.0 M HCl solution with 400 mg L-1 reaches 97.6 %, much much higher than the CS and the recently reported chitosan-based inhibitors. Scanning electron microscopy (SEM), atomic force microscopy (AFM), and water contact angle (WCA) results reveal that the CS-FGA molecules firmly adsorb on the MS surface to form a protective layer. The adsorption of CS-FGA on the MS surface belongs to the Langmuir adsorption isotherm containing both the physisorption and chemisorption. According to the X-ray photoelectron spectroscopy (XPS) and UV-vis spectrum, FeN bonds presented on the MS surface further prove the chemisorption between CS-FGA and Fe to generate the stable protective layer. Additionally, theoretical calculations from quantum chemical calculation (DFT) and molecular simulations (MD) were performed to reveal the inhibition mechanism of CS-FGA.

Accelerated corrosion of low carbon steel by oscillatory acidic streams generated with a bio-inspired claw device.

A mechanical device inspired by the pistol shrimp snapper claw was developed. This technology features a claw characterized by a periodic opening/closing motion, at a controlled frequency, capable of producing oscillating flows at transitional Reynolds numbers. An innovative method was also proposed for determining the corrosion rate of carbon steel samples under oscillating acidic streams (aqueous solution of HCl). By employing very-thin carbon steel specimens (25 µm thickness), with one side coated with Zn and not exposed to the stream, it became possible to electrochemically sense the Zn surface once the steel sample was perforated, thus providing the average dissolution rate into the most relevant pit on the steel surface. Furthermore, a laser light positioned beneath the metallic sample, along with a camera programmed to periodically capture images of the steel surface, facilitated the accurate counting of the number of newly formed pits. The system consisting of the thin steel sample and the Zn coating can be seen as a type of corrosion sensor. Furthermore, the proposed laser illumination method allows corroborating the electrochemical detection of pits and also establishing their location. The techniques crafted in this study pave the way for developing alternative corrosion sensors that boast appealing attributes: affordability, compactness, and acceptable accuracy to detect in time and space localized damage.

Pressure-relief joints of initial support structural system used in tunnels with high-stress surrounding rock.

To address the problem of large deformations in weak surrounding rock tunnels under high ground stress, which cause damage to initial support structures, this study proposes a novel type of circumferential pressure-relief joint based on the concept of relieving deformation pressure of the surrounding rock. Key parameters of the pressure-relief joint, such as initial bearing capacity peak, constant bearing capacity, and allowable pressure-relief displacement, were obtained through numerical simulations and laboratory experiments. A comparison was made between the mechanical characteristics of rigid joints and the new type of pressure-relief joint. The applicability of the pressure-relief joint was verified through field tests, monitoring the surrounding rock pressure, internal forces in the steel frames, and the convergence displacement of the support structure. The results show that: (1) In the elastic stage, the stiffness of the new pressure-relief joint is similar to that of rigid joints. In the plastic stage, rigid joints fail directly, whereas the pressure-relief joint can control deformation and effectively release the deformation pressure of the surrounding rock while providing a constant bearing capacity. (2) The right arch foot in the experiment had poor rock quality, leading to high stress in the steel frame and significant horizontal displacement. After the deformation of the pressure-relief joint, the stress in the surrounding rock and steel frame significantly reduced, and the rate of horizontal deformation of the support structure slowed down. (3) The vertical and horizontal final displacements of the pressure-relief joint in the experiment were 61mm and 15mm, respectively, which did not exceed the allowable deformation values. The components of the support structure remained intact, ensuring safety. However, this study has limitations: the design of the new pressure-relief joint only allows for a vertical deformation of 150mm and a horizontal deformation of 50mm, limiting the range of pressure-relief deformation.

Life cycle assessment of carbon footprint in dual-phase automotive strip steel production.

As the demand for automotive materials grows more stringent in environmental considerations, it becomes imperative to conduct thorough environmental impact assessments of dual-phase automotive strip steel (DP steel). However, the absence of detailed and comparable studies has left the carbon footprint of DP steel and its sources largely unknown. This study addresses this gap by establishing a cradle-to-gate life cycle model for DP steel, encompassing on-site production, energy systems, and upstream processes. The analysis identifies and scrutinizes key factors influencing the carbon footprint, with a focus on upstream mining, transportation, and on-site production processes. The results indicate that the carbon footprint of DP steel is 2.721 kgCO2-eq/kgDP, with on-site processes contributing significantly at 88.1%. Sensitivity analysis is employed to assess the impact of changes in resource structure, on-site energy, CO2 emission factors, and byproduct recovery on the carbon footprint. Proposals for mitigating carbon emissions in DP steel production include enhancing process gas recovery, transitioning to cleaner energy sources, and reducing the hot metal-to-steel ratio. These findings offer valuable insights for steering steel production towards environmentally sustainable practices.

Methacrylic acid in situ modified steel converter slag/natural rubber composites: Resourceful utilization of steelmaking solid wastes.

As a by-product of the steelmaking industry, the large-volume production and accumulation of steel converter slag cause environmental issues such as land occupation and dust pollution. Since metal salts of unsaturated carboxylic acid can be used to reinforce rubber, this study explores the innovative application of in-situ modified steel slag, mainly comprising metal oxides, with methacrylic acid (MAA) as a rubber filler partially replacing carbon black. By etching the surface of steel slag particles with MAA, their surface roughness was increased, and the chemical bonding of metal methacrylate salt was introduced to enhance their interaction with the molecular chain of natural rubber (NR). The results showed that using the steel slag filler effectively shortened the vulcanization molding cycle of NR composites. The MAA in-situ modification effectively improved the interaction between steel slag and NR molecular chains. Meanwhile, the physical and mechanical properties, fatigue properties, and dynamic mechanical properties of the experimental group with MAA in-situ modified steel slag (MAA-in-situ-m-SS) were significantly enhanced compared with those of NR composites partially filled with unmodified slag. With the dosage of 7.5 phr or 10 phr, the above properties matched or even exceeded those of NR composites purely filled with carbon black. More importantly, partially replacing carbon black with modified steel slag reduced fossil fuel consumption and greenhouse gas emission from carbon black production. This study pioneered an effective path for the resourceful utilization of steel slag and the green development of the steelmaking and rubber industries.

Conductive magnetic nanowires accelerated electron transfer between C1020 carbon steel and Desulfovibrio vulgaris biofilm.

Microbial biofilms are behind microbiologically influenced corrosion (MIC). Sessile cells in biofilms are many times more concentrated volumetrically than planktonic cells in the bulk fluids, thus providing locally high concentrations of chemicals. More importantly, "electroactive" sessile cells in biofilms are capable of utilizing extracellularly supplied electrons (e.g., from elemental Fe) for intracellular reduction of an oxidant such as sulfate in energy metabolism. MIC directly caused by anaerobic biofilms is classified into two main types based on their mechanisms: extracellular electron transfer MIC (EET-MIC) and metabolite MIC (M-MIC). Sulfate-reducing bacteria (SRB) are notorious for their corrosivity. They can cause EET-MIC in carbon steel, but they can also secrete biogenic H2S to corrode other metals such as Cu directly via M-MIC. This study investigated the use of conductive magnetic nanowires as electron mediators to accelerate and thus identify EET-MIC of C1020 by Desulfovibrio vulgaris. The presence of 40 ppm (w/w) nanowires in ATCC 1249 culture medium at 37 °C resulted in 45 % higher weight loss and 57 % deeper corrosion pits after 7-day incubation. Electrochemical tests using linear polarization resistance and potentiodynamic polarization supported the weight loss data trend. These findings suggest that conductive magnetic nanowires can be employed to identify EET-MIC. The use of insoluble 2 µm long nanowires proved that the extracellular section of the electron transfer process is a bottleneck in SRB MIC of carbon steel.

Comparison of MBT biotargets with MBT steel targets for matrix-assisted laser desorption/ionization time of flight mass spectrometry identifications of microorganisms in a clinical microbiology laboratory.

MALDI-TOF MS identifications of microorganisms in a clinical laboratory were investigated, comparing steel targets with MBT Biotargets. By using MBT Biotargets, the score values of yeast identifications increased, whereas the score values of Gram-negative bacteria decreased. Switching to MBT Biotargets did not negatively impact overall frequencies of high confidence identifications.

Analysis and prediction of compressive and split-tensile strength of secondary steel fiber reinforced concrete based on RBF fuzzy neural network model.

Accurate analysis of the strength of steel-fiber-reinforced concrete (SFRC) is important for ensuring construction quality and safety. Cube compression and splitting tensile tests of steel fiber with different varieties, lengths, and dosages were performed, and the effects of different varieties, lengths, and dosages on the compressive and splitting properties of secondary concrete were obtained. It was determined that the compression and splitting strengths of concrete could be effectively improved by the addition of end-hooked and milled steel fibers. The compressive and splitting strengths of concrete can be enhanced by increasing the fiber length and content. However, concrete also exhibits obvious uncertainty owing to the comprehensive influence of steel fiber variety, fiber length, and fiber content. In order to solve this engineering uncertainty, the traditional RBF neural network is improved by using central value and weight learning strategy especially. On this basis, the RBF fuzzy neural network prediction model of the strength of secondary steel fiber-reinforced concrete was innovatively established with the type, length and content of steel fiber as input information and the compressive strength and splitting tensile strength as output information. In order to further verify the engineering reliability of the prediction model, the compressive strength and splitting tensile strength of steel fiber reinforced concrete with rock anchor beams are predicted by the prediction model. The results show that the convergence rate of the prediction model is increased by 15%, and the error between the predicted value and the measured value is less than 10%, which is more efficient and accurate than the traditional one. Additionally, the improved model algorithm is efficient and reasonable, providing technical support for the safe construction of large-volume steel fiber concrete projects, such as rock anchor beams. The fuzzy random method can also be applied to similar engineering fields.

Influence of fixed orthodontic steel retainers on gingival health and recessions of mandibular anterior teeth in an intact periodontium - a randomized, clinical controlled trial.

OBJECTIVE: Aim of this randomized clinical controlled trial was to evaluate the influence of fixed orthodontic steel retainers on gingival health and recessions of mandibular anterior teeth. MATERIALS AND METHODS: After end of the orthodontic treatment, patients were randomly assigned into the test (fixed steel retainer) or control group (modified removable vacuum-formed retainer). Periodontal parameters (periodontal probing depth: PPD; recession: REC; bleeding on probing: BOP) as well as plaque and gingival index were assessed on mandibular anterior teeth directly before attaching/handing over the retainer (baseline: BL), 6 and 12 months after orthodontic treatment. RESULTS: 37 patients (test: n = 15, mean age: 16.1±4.2 years; control: n = 17, mean age: 17.1±5.4 years) completed the study. REC and PPD failed to show significant pairwise differences. The number of patients showing gingival health in the area of the mandibular anterior teeth (test: BL n = 10, 6 months n = 9, 12 months n = 11; control: BL n = 10, 6 months n = 16, 12 months n = 15) revealed a significant difference for the intra-group comparison between BL and 6 months in the control group (p = 0.043). The inter-group comparisons failed to show significant differences. CONCLUSION: Young orthodontically treated patients with fixed steel retainers show in 73.3% healthy gingival conditions after one year which are comparable to the control group (88.2%). Gingival recessions were in a clinically non-relevant range at any time of the examination. CLINICAL TRIAL NUMBER: DRKS00016710.

Multi-process production occurs in the iron and steel industry, supporting 'dual carbon' target: An in-depth study of CO2 emissions from different processes.

Reducing CO2 emissions of the iron and steel industry, a typical heavy CO2-emitting sector, is the only way that must be passed to achieve the 'dual-carbon' goal, especially in China. In previous studies, however, it is still unknown what is the difference between blast furnace-basic oxygen furnace (BF-BOF), scrap-electric furnace (scrap-EF) and hydrogen metallurgy process. The quantitative research on the key factors affecting CO2 emissions is insufficient. There is also a lack of research on the prediction of CO2 emissions by adjusting industrial structure. Based on material flow analysis, this study establishes carbon flow diagrams of three processes, and then analyze the key factors affecting CO2 emissions. CO2 emissions of the iron and steel industry in the future is predicted by adjusting industrial structure. The results show that: (1) The CO2 emissions of BF-BOF, scrap-EF and hydrogen metallurgy process in a site are 1417.26, 542.93 and 1166.52 kg, respectively. (2) By increasing pellet ratio in blast furnace, scrap ratio in electric furnace, etc., can effectively reduce CO2 emissions. (3) Reducing the crude steel output is the most effective CO2 reduction measure. There is still 5.15 × 108-6.17 × 108 tons of CO2 that needs to be reduced by additional measures.

Inhibitory effect of marine Bacillus sp. and its biomineralization on the corrosion of X65 steel in offshore oilfield produced water.

The issue of material failure attributed to microbiologically influenced corrosion (MIC) is escalating in seriousness. Microorganisms not only facilitate corrosion but certain beneficial microorganisms also impede its occurrence. This study explored the impact of marine B. velezensis on the corrosion behavior of X65 steel in simulated offshore oilfield produced water. B. velezensis exhibited rapid growth in the initial stages, and the organic acid metabolites were found to promote corrosion. Subsequently, there was an increase in cross-linked "networked" biofilms products, a significant rise in the prismatic shape of corrosion products, and a tendency for continuous development in the middle and late stages. The organic/inorganic mineralized film layer formed on the surface remained consistently complete. Metabolic products of amino acid corrosion inhibitors were also observed to be adsorbed into the film. B. velezensis altered the kinetics of the X65 steel cathodic reaction, resulting in a deceleration of the electrochemical reaction rate. The mineralization induced by B. velezensis effectively slowed down the corrosion rate of X65 steel.

Influence of marine Shewanella putrefaciens and mediated calcium deposition on Q235 carbon steel corrosion.

The microbiologically influenced corrosion inhibition (MICI) of Q235 carbon steel by Shewanella putrefaciens and mediated calcium deposition were investigated by regulating microbial mineralization. In a calcium-rich medium, S. putrefaciens rapidly created a protective calcium carbonate layer on the steel surface, which blocked Cl- diffusion. Without calcium, the biofilm and rust layer mitigated pitting corrosion but did not prevent Cl- penetration. Potentiodynamic polarization results indicated that the current densities (icorr values) of the corrosion produced in the S. putrefaciens-inoculated media with and without calcium were 0.4 µA/cm2 and 0.6 µA/cm2, respectively. Similarly, compared with those under sterile conditions, the corrosion inhibition rates were 92.2% and 87.4% higher, respectively. Electrochemical impedance spectroscopy (EIS) and scanning electrochemical microscopy (SECM) confirmed that the MICI was caused by the combination of microbial aerobic respiration and the deposited layers. Even under nonbiological conditions, S. putrefaciens-induced calcium carbonate deposition inhibited corrosion.

Corrosion inhibition of mild steel in 1 M HCl using water soluble chitosan derivative of vanillin.

The water-soluble chitosan derivative (WSCD) was made by mixing chitosan with sodium hydroxide, treating the mixture with chloroacetic acid, and then forming a Schiff base with vanillin in an acidic medium. In this study, we examined the corrosion-inhibiting ability of a WSCD on mild steel surfaces in acidic environments. Weight loss, EIS, PDP, LPS, and OCP measurements were used to study the corrosion resistance on mild steel surfaces in 1 M HCl solutions with known concentrations of WSCD. The results show that WSCD functions effectively as a mixed-type anodic and cathodic inhibitor, providing 87 % corrosion inhibition efficiency at 75 ppm. Using SEM to investigate the morphology of corroded mild steel with and without varying amounts of WSCD, impedance measurements show the development of a thin film of inhibitor on the metal surface, the extent of which increases as the inhibitor concentration rises. The WSCD molecule first adsorbs on mild steel and follows Langmuir adsorption isotherm. It is found that the (∆Gads0)adsorption's free energy is -17.473 kJ/mol. The contact angle measurements confirm that the hydrophobicity of the metal surface has increased as a result of the inhibitor's thin film development.