[Determination of 222 pesticide residues in olive oil by fully automatic QuEChERS pre-treatment instrument coupled with gas chromatography-quadrupole-time-of-flight mass spectrometry].

Pesticide residues may be present in olive oil because pesticides are applied to olive trees during their cultivation and growth for pest prevention and some of these pesticides are not easily degraded. Studies on pesticide residues in olive oil have mainly focused on the detection of single types of pesticide residues, and reports on the simultaneous detection of multiple pesticide residues are limited. At present, hundreds of pesticides with different polarities and chemical properties are used in practice. In this study, an analytical method based on fully automatic QuEChERS pretreatment instrument coupled with gas chromatography-quadrupole time-of-flight mass spectrometry (GC-QTOF-MS) was established for the rapid determination of 222 pesticide residues in olive oil. The effects of acetonitrile acidification concentration, n-hexane volume, oscillation time, centrifugation temperature, and purification agent on the determination of the 222 pesticide residues were investigated. First, ions with good responses and no obvious interference were selected for quantification and characterization. The purification process was then developed by setting the parameters of the fully automatic QuEChERS pretreatment instrument to optimal values. The sample was extracted with acetonitrile containing 2% formic acid, and the supernatant was purified by centrifugation in a centrifuge tube containing 400 mg N-propylethylenediamine (PSA), 400 mg octadecylsilane-bonded silica gel (C18), and 1200 mg anhydrous magnesium sulfate. The purified solution was blown dry with nitrogen and then fixed with ethyl acetate for instrumental analysis. Finally, a matrix standard solution was used for quantification. The method was validated in terms of matrix effects, linear ranges, limits of detection (LODs) and quantification (LOQs), accuracies, and precisions. The results showed that 86.04% of the 222 pesticides had linear ranges of 0.02-2.00 µg/mL, 10.81% had linear ranges of 0.10-2.00 µg/mL, and 3.15% had linear ranges of 0.20-2.00 µg/mL. The pesticide residues showed good relationships within their respective linear ranges, and the correlation coefficients (R2) were greater than 0.99. The LODs of all tested pesticides ranged from 0.002 to 0.050 mg/kg, and their LOQs ranged from 0.007 to 0.167 mg/kg. Among the 222 pesticides determined, 170 pesticides had LOQs of 0.007 mg/kg while 21 pesticides had LOQs of 0.017 mg/kg. At the three spiked levels of 0.2, 0.5, and 0.8 mg/kg, 79.58% of all tested pesticides had average recoveries of 70%-120% while 65.92% had average recoveries of 80%-110%. In addition, 93.54% of all tested pesticides had relative standard deviations (RSDs, n=6)<10% while 98.35% had RSDs (n=6)<20%. The method was applied to 14 commercially available olive oil samples, and seven pesticides were detected in the range of 0.0044-0.0490 mg/kg. The residues of fenbuconazole, chlorpyrifos, and methoprene did not exceed the maximum limits stated in GB 2763-2021. The maximum residual limits of molinate, monolinuron, benalaxyl, and thiobencarb have not been established. The method utilizes the high mass resolution capability of TOF-MS, which can improve the detection throughput while ensuring good sensitivity. In addition, high-resolution and accurate mass measurements render the screening results more reliable, which is necessary for the high-throughput detection of pesticide residues. The use of a fully automatic QuEChERS instrument in the pretreatment step reduces personnel errors and labor costs, especially when a large number of samples must be processed, thereby offering significant advantages over other approaches. Moreover, the method is simple, rapid, sensitive, highly automatable, accurate, and precise. Thus, it meets requirements for the high-throughput detection of pesticide residues in olive oil and provides a reference for the development of detection methods for pesticide residues in other types of oils as well as the automatic pretreatment of complex matrices.

Multiresidue extraction of current-use pesticides from complex solid matrices using energized dispersive guided extraction with analysis by gas and liquid chromatography tandem mass spectroscopy.

The development of sample processing techniques that recover a broad suite of pesticides from solid matrices, while mitigating coextracted matrix interferences, and reducing processing time is beneficial for high throughput analyses. The objective of this study was to evaluate the effectiveness of an automated extraction system for pesticide analyses in solid environmental samples. An Energized Dispersive Guided Extraction (EDGE) system was used to evaluate two different extraction solvents in optimizing the extraction of 210 pesticides and pesticide transformation products. A graphitized carbon cleanup step was implemented, and three elution solvents were evaluated separately for analyte recoveries. Recoveries between 70 and 130% were achieved for 167 compounds in a test soil using acetonitrile as an extraction solvent and carbon cleanup with acetonitrile and dichloromethane elutions. Nine field samples (soil, sediment, and biosolids) were extracted using the newly developed method and were compared with a previously validated pressurized liquid extraction (PLE) method using an Accelerated Solvent Extraction (ASE) system. Concentrations obtained from the two methods were comparable (linear R2 > 0.999), suggesting similar performance between the EDGE and PLE extractions in complex matrices. The new method provided slightly better sensitivities in comparison to the PLE method, ranging from 0.09 to 2.56 ng g-1. The method presented here significantly reduces extraction setup and runtimes while also minimizing the volume of carcinogenic solvents (e.g., dichloromethane) used in the laboratory and presents a sensitive multiresidue method for a wide range of pesticides in solid matrices.

Determination of Cyclaniliprole in Fruits and Vegetables Using Disposable Pipette Extraction Cleanup and Ultrahigh-Performance Liquid Chromatography-Tandem Mass Spectrometry.

Despite an outstanding agent for control of Lepidoptera, the diamide insecticide cyclaniliprole (CYCP) is a suspected carcinogen. In the present study, an analytical method was developed for the determination of CYCP in six fruits and vegetables (apple, grape, peach, bell pepper, lettuce, and tomato) using ultrahigh-performance liquid chromatography coupled with tandem mass spectrometry. Sample preparation was carried out by the acetonitrile-salting-out extraction followed by simple and fast cleanup of disposable pipette extraction tip containing styrene divinyl benzene and/or graphitized carbon black. Satisfactory linearity (r > 0.99) was obtained in the calibration range of 0.001−1 µg mL−1. Matrix effects decreased from −9.9−−17.9% to −1.0−−7.6% after the cleanup. The recoveries of CYCP at three spike levels (0.01, 0.1, and 1 mg kg−1) from different matrices were between 75.7% and 111.5%, with the intra-day (n = 5) and inter-day (n = 15) relative standard deviations lower than 12.1%. The limit of quantification was 0.01 mg kg−1. The developed method provides a good reference for routine monitoring of CYCP in these fruits and vegetables.

[Rapid screening of 84 pesticide residues in dendrobium by Sin-QuEChERS Nano purification column with gas chromatography-tandem mass spectrometry].

A rapid screening method for 84 pesticide residues in dendrobium perfringens parent material with different polarities was developed using a Sin-QuEChERS Nano clean-up column combined with gas chromatography-tandem mass spectrometry (GC-MS/MS). The differences in extraction efficiency of the targets were compared with different extraction solvents (acetonitrile containing 1% acetic acid, acetone) and methods (immersion with or without water). The purification effect and extraction recoveries of Sin-QuEChERS Nano method and classical dispersive solid-phase extraction (dSPE), solid-phase extraction (SPE) and QuEChERS were systematically compared using Dendrobium nobile samples. The differences in matrix effects between the Sin-QuEChERS Nano method, which was more effective in purification, and the dSPE method were also analyzed. The purification effects of three commercially available Sin-QuEChERS Nano purification columns (simple matrix purification column, complex matrix purification column and herbal purification column) were compared. The applicability of the purification methods were also verified by using different parts of Dendrobium nobile samples (stems, leaves and flowers). From the results, it could be concluded that weighing 2.00 g and the samples in 5 mL of water for 20 min, followed by extraction with acetonitrile containing 1% acetic acid was more effective. The average extraction recovery of the target components by Sin-QuEChERS Nano purification method was 90.5%, which further identified Sin-QuEChERS Nano-Chinese medicine purification column as the preferred purification column for dendrobium purification. The target components were separated by a DB-1701MS quartz capillary column (30 m×0.25 mm×0.25 µm) with programmed temperature rise, detected by multiple reaction monitoring (MRM) mode, and quantified by matrix-matched solution external standard method. The GC-MS/MS assay was used for the methodological validation of the 84 representative pesticides within Dendrobium officinale and Dendrobium nobile was carried out by GC-MS/MS detection method. The results indicated that the targets showed excellent linear correlation in different scopes with correlation coefficients (r2) >0. 990. The limits of detection (LODs, S/N=3) of the method were 1.5 to 5.8 µg/kg, and the limits of quantification (LOQs, S/N=10) ranged from 5.0 to 15.0 µg/kg. The spiked recoveries of the target pesticides under different spiked levels were 68.7%-116.2%, and the relative standard deviations (RSDs, n=6) were less than 15%. Compared to other typical pretreatment methods, the Sin-QuEChERS Nano method provided better performance in terms of purification. The method not only effectively removed pigments, organic acids, and alkaline interferents, but also saved preparation time. Losses due to solvent transfer were also avoided and no further vortexing or centrifugation was required, making it a simplified and effective extraction and purification procedure. The method was sensitive, rapid, simple and reliable. It effectively improved the detection efficiency during the rapid screening of pesticides in dendrobium and presented a strong practical application value. In addition, the developed method could further expand the types of target pesticides and could be used to detect more pesticide residues in foods and Chinese herbal medicine. The established Sin-QuEChERS Nano method was used for the analysis of authentic samples. The applicability of the method was evaluated by analyzing a total of 80 samples collected from Anlong, Libo, Dushan, and Yanhe County in Guizhou Province. The types of samples included dendrobium maple, Dendrobium nobile (flowers, stems, leaves) and Dendrobium officinale (flowers, stems, leaves, powder, tablets). At least one pesticide residue was detected in 12 samples, with a detection rate of 15%. The five pesticides with higher detection rates and residues were chlorpyrifos (0.08-0.5 mg/kg), chlorothalonil (0.06-3.2 mg/kg), propanil zinc (0.03-0.15 mg/kg), methyl parathion (0.04-0.23 mg/kg) and cyhalothrin (0.10-2.68 mg/kg). Except for the pesticides in maximum residue limits (MRLs), the pesticide residues detected from dendrobium samples were below the limits set by Chinese national standard (GB 2763-2021) and local standard DBS 52/048-2020.

[Simultaneous determination of six haloacetonitriles in finished water for drinking by purge and trap-gas chromatography-triple quadrupole mass spectrometry].

Haloacetonitriles (HANs) are widely used in finished water as unregulated disinfection by-products. HANs may pose much threat to human health, and there is no relevant standard examination method for these compounds. A method was established for the simultaneous determination of six HANs (chloroacetonitrile (CAN), dichloroacetonitrile (DCAN), trichloroacetonitrile (TCAN), bromoacetonitrile (BAN), bromochloroacetonitrile (BCAN), and dibromoacetonitrile (DBAN)) in finished water by using purge and trap-gas chromatography-triple quadrupole mass spectrometry (GC-MS/MS). The purge and trap technology helps realize automatic determination of samples after collection, without using any harmful reagent. The cost and analytical efficiency of this method were superior to those of solid phase microextraction (SPME). Considering the instability of HANs, the analysis must be carried out as soon as possible after sampling, in order to avoid significant changes in their concentration during storage. In particular, the use of an appropriate quenching agent was critical to sample collection. In this study, ascorbic acid was chosen as the quenching agent. The stabilities of the spiked samples at the levels of 0.1 (TCAN), 0.2 (CAN), 1.0 (DCAN), 1.0 (BAN), 1.0 (BCAN), 4.0 (DBAN) µg/L were tested. The effect of sample storage time (0, 0.5, 1, 2, 3, 4, and 6 h) on the responses of the target component was evaluated. The stability results showed that within 6 h, the relative standard deviations of the responses for the six HANs ranged from 2.32% to 6.98%. To validate the method, first, different traps, viz. 7# (Tenax), 10# (Teanx/silica gel/cms), 11# (VOCARB), and 12# (BTEXTRAP) were optimized. Second, various chromatographic columns (VF-5, Rxi-624, DB-VRX, and HP-INNOWAX) were compared to investigate their influence on the peak shape. Under the optimal detection conditions, the six HANs in finished water were extracted with the 10# trap. The volume of the water sample was used 25 mL, with purging at 35 ℃ for 11 min, and desorbed at 190 ℃ for 1 min. Chromatographic separation was performed on a Rxi-624Sil MS chromatographic column (60 m×0.25 mm×1.40 µm). Gas chromatographic conditions were obtained under the following conditions: split ratio, 1∶10; linear velocity, 30 cm/s. The triple quadrupole mass spectrometer was operated in the electron impact (EI) mode. The target compounds were detected in the multiple reaction monitoring (MRM) mode. Quantitation was carried out using the external standard method. The results showed that the matrix effects of the six HANs ranged from 0.85 to 1.09. Good linearities were obtained in the range of the standard curves. The correlation coefficients (r) were greater than 0.9991. The limits of detection (LODs, S/N=3) were 0.8-120.0 ng/L. The limits of quantification (LOQs, S/N=10) were 1.5-300.0 ng/L. The average recoveries of the six HANs ranged from 84.2% to 106%, and the RSDs were in the range of 1.81%-10.7%. In August 2020, 38 samples of finished water were tested. All of the six HANs were found in the finished water. The concentrations of the HANs were in the range of 0.0101-1.28 µg/L, and the total detection rate was 92.1%. The detection rates of the individual components followed the order DCAN>BCAN>CAN>TCAN>BAN>DBAN. The developed method is efficient, sensitive, and environmentally friendly. It provides a high-quality technical choice for monitoring and health risk assessment of the emerging disinfection by-products of HANs.

Optimization of microwave assisted extraction of simmondsins and polyphenols from Jojoba (Simmondsia chinensis) seed cake using Box-Behnken statistical design.

A closed-vessel microwave-assisted extraction (MAE) of simmondsins and polyphenols from defatted Jojoba cake using Box-Benkhen design with four independent variables (solvent/cake ratio, ethanol concentration, extraction time and microwave power) was investigated. ANOVA results showed that the obtained models were significant at 95% confidence level. Optimal extraction conditions were found for highest values of microwave power (500 W) and extraction time (15 min) and for moderate values of solvent to cake ratio (41 - 45 mL/g). Optimum simmondsins yield (23.35%) was obtained with pure water as solvent. However, optimum polyphenols yield (2.33%) and ORAC antioxidant activity (656 µmol TE/g) were obtained with 46.79% and 42.04% ethanol in water, respectively. ORAC antioxidant activity was found to be well correlated to polyphenol and simmondsin contents. These results indicate that MAE is an effective technique for recovery of bioactive compounds for food and pharmaceutical industries from Jojoba by-products.

Magnetic covalent organic framework as a solid-phase extraction absorbent for sensitive determination of trace organophosphorus pesticides in fatty milk.

A simple and efficient magnetic solid-phase extraction (MSPE) method was established with magnetic covalent organic framework (COF) as adsorbent to enrich organophosphorus pesticides from fatty milk samples, followed by the sensitive determination via LC-MS/MS. The key parameters influencing the MSPE efficiency were comprehensively investigated to afford an optimized procedure. All the target analytes could be captured directly by magnetic COF from milk without protein precipitation, making the pretreatment rapid and convenient. Systematic method validation demonstrated its satisfactory linearity, recoveries (80.0-105 %), and precision (RSDs <12.3 %). The method limits of quantification were 0.2-0.5 µg L-1. A comparison experiment to the reported solid-phase extraction fully verified the present MSPE more rapid, accurate, and environment-friendly. Furthermore, FT-IR and XPS analysis were performed to reveal the adsorption mechanisms of magnetic COF to organophosphorus pesticides, which could offer guidance on the rational design of COF adsorbent for various target analytes.

Has the formation of disinfection by-products been overestimated? Membrane leakage from syringe filter heads serves as unexpected precursors.

Syringe filters are widely used for sample pretreatments in laboratories. This study found that, surprisingly, these filters can leak dissolved organic carbon (DOC) that can potentially serve as precursors of disinfection by-products (DBPs). Nine common types of syringe filters were assessed. The results showed that the DOC of ultrapure water increased after syringe filtration. The DOC shed from filter membranes was characterized, whose spectra showed that the main compounds exhibited a low apparent molecular weight. Five classes of DBPs were investigated including trihalomethanes, haloacetaldehydes, haloacetonitriles, haloacetamides and halonitromethanes, among which trichloromethane (TCM), dichloroacetaldehyde (DCAL), trichloroacetaldehyde (TCAL), dichloroacetonitrile (DCAN), and trichloronitromethane (TCNM) were principally detected. The DBP formation was affected by chlorination time and membrane types. In general, the use of the poly vinylidene fluoride membrane resulted in the highest formation of TCM and TCAL, whereas nylon and mixed cellulose esters membranes contributed significantly to the formation of DCAN and TCNM, respectively. The shedding DOC and the formation of TCM, DCAL and TCAL from filter membranes were mitigated effectively by pre-washing; however, the contribution of membrane leakage to DCAN and TCNM formation was still notable, even with a pre-wash volume of 50 mL. When unwashed syringe filters were used for a real water sample, the DBP formation increased by up to 73.2% compared to the pre-washed ones; particularly for TCNM it was always over 15%. Therefore, for better quality control in laboratories, more attention should be paid to the syringe filters during sample pre-treatments, particularly when DBP formation is being investigated.

Human transport of thirdhand tobacco smoke: A prominent source of hazardous air pollutants into indoor nonsmoking environments.

The contamination of indoor nonsmoking environments with thirdhand smoke (THS) is an important, poorly understood public health concern. Real-time THS off-gassing from smokers into a nonsmoking movie theater was observed with online and offline high-resolution mass spectrometry. Prominent emission events of THS tracers (e.g., 2,5-dimethylfuran, 2-methylfuran, and acetonitrile) and other tobacco-related volatile organic compounds (VOCs) coincided with the arrival of certain moviegoers and left residual contamination. These VOC emission events exposed occupants to the equivalent of 1 to 10 cigarettes of secondhand smoke, including multiple hazardous air pollutants (e.g., benzene and formaldehyde) at parts-per-billion concentrations. Nicotine and related intermediate-volatility nitrogen-containing compounds, which vaporized from clothes/bodies and recondensed onto aerosol, comprised 34% of observed functionalized organic aerosol abundance. Exposure to THS VOC emission events will be considerably enhanced in poorly ventilated or smaller spaces in contrast with a large, well-ventilated theater-amplifying concentrations and potential impacts on health and indoor chemistry.

Simultaneous analysis of haloacetonitriles, haloacetamides and halonitromethanes in chlorinated waters by gas chromatography-mass spectrometry.

Nitrogenous classes of disinfection by-products (DBPs), such as haloacetamides (HAAms), haloacetonitriles (HANs) and halonitromethanes (HNMs), while generally present at lower concentrations in disinfected waters than carbonaceous DBPs, such as trihalomethanes or haloacetic acids, have been shown to be more detrimental to human health. While several methods have been shown to be suitable for the analysis of some nitrogenous DBPs (N-DBPs) in disinfected waters, many are unable to quantify HAAms, the most detrimental to health of these three N-DBP classes. Here, we report the first method for the simultaneous analysis of twenty-five N-DBPs (nine HANs, nine HNMs and seven HAAms) in disinfected waters using liquid-liquid extraction followed by gas chromatography-mass spectrometry. The use of a programmable temperature vaporiser injector minimises degradation of the thermally labile HNMs, while avoiding the concomitant decreases in HANs and HAAms which occur when using lower injector temperatures. Extraction parameters, including sample pH, solvent volume, salt addition and sample pre-concentration, were investigated to determine the optimal conditions across all target N-DBPs. Good detection limits were achieved for all analytes (0.8-1.7 µg L-1) and both laboratory and instrumental runtimes were significantly reduced compared to previous methods. The method was validated for the analysis of N-DBPs in drinking, swimming pool and spa waters, and concentrations of up to 41 µg L-1 of some N-DBPs were measured in some pools.

Development of an LC⁻Tandem Mass Spectrometry Method for the Quantitative Analysis of Hercynine in Human Whole Blood.

Given that the peculiar redox behavior of ergothioneine involves a rapid regeneration process, the measurement of its precursor and redox metabolite hercynine could be particularly useful in assessing its role in oxidative stress or other biological processes. Thus, a LC-MS/MS method for the determination of hercynine concentrations in whole blood was developed. After lysis of red blood cells by cold water, samples were filtered on micro concentrators at a controlled temperature of 4 °C. The clear filtered fluid was then treated with diethylpyrocarbonate to derivatize hercynine for the analysis by LC-MS/MS. The derivatized analyte was isocratically separated as a carbethoxy derivative on a C18 column with a mobile phase of an aqueous 0.1% v/v formic acid and acetonitrile (95:5). Effluents were monitored by MRM transitions at m/z 270.28→95 and 273.21→95 for hercynine and its deuterated counterpart, respectively. No cross-talk between MRM transitions was observed and a good linearity was found within a range of 35⁻1120 nmol/L. The LOD and LOQ were, respectively, 10.30 and 31.21 nmol/L with an intraday and intermediate precision below 7%. The average hercynine concentration in whole blood from 30 healthy male volunteers (aged 77 ± 12 years) was 178.5 ± 118.1 nmol/L. Overall, the method is easy to perform, allowing a rapid and accurate assessment of whole blood concentrations of hercynine.

Molecular Detection for Unconcentrated Gas With ppm Sensitivity Using 220-to-320-GHz Dual-Frequency-Comb Spectrometer in CMOS.

Millimeter-wave/terahertz rotational spectroscopy of polar gaseous molecules provides a powerful tool for complicated gas mixture analysis. In this paper, a 220-to-320-GHz dual-frequency-comb spectrometer in 65-nm bulk CMOS is presented, along with a systematic analysis on fundamental issues of rotational spectrometer, including the impacts of various noise mechanisms, gas cell, molecular properties, detection sensitivity, etc. Our comb spectrometer, based on a high-parallelism architecture, probes gas sample with 20 comb lines simultaneously. It does not only improve the scanning speed by 20, but also reduces the overall energy consumption to 90 mJ/point with 1 Hz bandwidth (or 0.5 s integration time). With its channelized 100-GHz scanning range and sub-kHz specificity, wide range of molecules can be detected. In the measurements, state-of-the-art total radiated power of 5.2 mW and single sideband noise figure of 14.6-19.5 dB are achieved, which further boost the scanning speed and sensitivity. Finally, spectroscopic measurements for carbonyl sulfide (OCS) and acetonitrile (CH CN) are presented. With a path length of 70 cm and 1 Hz bandwidth, the measured minimum detectable absorption coefficient reaches  cm. For OCS that enables a minimum detectable concentration of 11 ppm. The predicted sensitivity for some other molecules reaches ppm level (e.g., 3 ppm for hydrogen cyanide), or 10 ppt level if gas preconcentration with a typical gain of 10 is used.

Multi-residue pesticide analysis in virgin olive oil by nanoflow liquid chromatography high resolution mass spectrometry.

In this article, a nanoflow liquid chromatography system coupled to high resolution mass spectrometry (nanoflow LC/ESI Q-Orbitrap-MS) has been applied for the development of a multiresidue pesticide method for the determination of 162 multiclass pesticides in olive oil samples. Due to the relatively high lipid content of the raw QuEChERS acetonitrile extracts obtained from this type of fatty vegetable samples, a dispersive solid phase extraction (dSPE) sorbent proposed to retain both fatty acids and triglycerides, namely Enhanced Matrix Removal-Lipid (EMR-Lipid) has been implemented as additional cleanup step. The analytical performances of the proposed method were evaluated,achieving recoveries in the range 75-119% with relative standard deviations lower than 19% (n = 6). The dSPE sorbent allowed the removal of most coextracted interferences without a significant loss of analytes. Matrix effects were also evaluated, showing a negligible effect for most of the compounds tested, when a dilution factor of 50 was applied. Notably, despite the use of relatively high dilution factors (e.g. 1:50) to minimize matrix effects, the lowest concentration levels detected with this method - in the low µg kg-1 range - are well below the corresponding maximum residue levels established by the current European legislation.

Simultaneous determination and risk assessment of metalaxyl and azoxystrobin in potato by liquid chromatography with tandem mass spectrometry.

A liquid chromatography with tandem mass spectrometry method was developed and validated to simultaneously determine metalaxyl and azoxystrobin in soil, potato, and potato foliage samples. The samples were extracted by 20 mL of acetonitrile and purified with dispersive solid-phase extraction using octadecyl silane as sorbent. The method showed good linearity (determination coefficients ≥ 0.9926) for metalaxyl (2.5-500 ng/mL) and azoxystrobin (5-1000 ng/mL). The limits of detection and quantification for both fungicides were 1.5-20 µg/kg. The average recoveries in soil, potato, and potato foliage were 83.07-92.87% for metalaxyl and 82.71-98.53% for azoxystrobin. The intra- and inter-day relative standard deviations were all less than 9%. The method was successfully applied on the residual analysis of metalaxyl and azoxystrobin in field trial samples. The results showed that the concentrations of metalaxyl and azoxystrobin in potato samples collected from Guizhou and Hunan were below 50 and 100 µg/kg (maximum residue limit set by China), respectively, at 5 days after the last application. When following the recommended application manual, metalaxyl and azoxystrobin do not present health concerns to the population because the risk quotients are far below 100%. All the above data could help and promote the safe and proper use of metalaxyl and azoxystrobin in potato.

Health risk assessment of haloacetonitriles in drinking water based on internal dose.

To estimate the health risk of haloacetonitriles in different kinds of drinking water, the concentrations of haloacetonitriles in tap water, boiled water and direct drinking water were detected. The physiologically based pharmacokinetic (PBPK) model was used to calculate internal dose in the human body for haloacetonitriles through ingestion, and the probability distributions of the non-carcinogenic risk of haloacetonitriles for human via drinking water were assessed. This study found that the mean concentrations of dichloroacetonitrile (DCAN) in tap water, boiled water and direct drinking water were 0.955 µg/L, 0.207 µg/L and 0.127 µg/L, and those of dibromoacetonitrile (DBAN) were 0.221 µg/L, 0.104 µg/L, 0.089 µg/L, respectively. In China, direct drinking water is used most frequently, so the concentrations of haloacetonitriles in direct drinking water were used to obtain data on the internal dose of haloacetonitriles. In addition, the simulation results for the PBPK model showed that the highest and lowest concentrations of DCAN occurred in the liver and venous blood, respectively. The peak concentrations of DBAN in each tissue were in the decreasing order liver > rapidly perfused tissue > kidney > slowly perfused tissues > fat > arterial blood (venous blood). In addition, the highest 95th percentile hazard quotients (HQ) value of haloacetonitriles via drinking water for humans was 8.89 × 10-3, much lower than 1. The 95th percentile hazard index (HI) was 0.046, which was also lower than 1, suggesting that there was no obvious non-carcinogenic risk.

Kinetics, mechanisms, and influencing factors on the treatment of haloacetonitriles (HANs) in water by two household heating devices.

Haloacetonitriles (HANs) are a group of nitrogenous disinfection by-products (DBPs) commonly found in treated water with potential carcinogenic, cytotoxic, and genotoxic risks. In order to control HANs and understand their real intake levels by people via drinking water, this study evaluated a list of structural, operational, and environmental factors affecting the treatment of HANs by two domestic heating devices, i.e., an electric boiler and a microwave oven. Results show that the concentrations of HANs decreased exponentially over time with increasing temperature, water turbulence, and bubbles, and the phenomena were most likely due to a combined effect of volatilization and hydrolysis. Among HANs, the lability increased with increasing halogenation degrees (i.e., tri- > di- > mono- HANs) yet decreasing halogen molecular weights (i.e., Cl- > Br- > I- HANs); such trends were well captured by quantitative structure activity relationship models (R2 = 0.99). Operational factors played critical roles in controlling HANs too, including the rate of heating, water volume, water temperature at time of pouring, cooling method, and capping condition, suggesting that people could benefit from proper handling methods and procedures. In addition, HANs added to tap water exhibited higher removals than those added to ultrapure water, probably because of the presence of free chlorine in tap water.

Correlation between Odor Concentration and Volatile Organic Compounds (VOC) Composition of Environmental Tobacco Smoke (ETS).

We examined the correlation between the odor concentration and the chemical composition of environmental tobacco smoke (ETS). Three types of ETS samples were prepared: secondhand smoke (SHS), thirdhand smoke (THS), and field ETS samples from an outside smoking area. The odor concentrations of the ETS, SHS, and THS samples were determined by the triangle-odor-bag method, and the chemical compositions were determined by proton transfer mass spectrometry. The odor concentration of the SHS samples was three or four orders of magnitude higher than that of the field ETS samples, and three orders of magnitude higher than that of the THS samples. The concentration ratios of the constituent chemicals in THS to those in SHS were about 10-4, corresponding to the ratio of the odor concentration. The concentration ratios of the constituent chemicals in the field ETS samples were much lower than the ratios of the odor concentrations. This suggests that the main contributing components to the odor of the field ETS samples are different from those in SHS and THS. The main contributors of the odor in the field ETS samples could be acetaldehyde, acetonitrile, acetic acid, and other unknown components with a mass-to-charge ratio (m/z) of 39 and 43.

Status of selected ion flow tube MS: accomplishments and challenges in breath analysis and other areas.

This article reflects our observations of recent accomplishments made using selected ion flow tube MS (SIFT-MS). Only brief descriptions are given of SIFT-MS as an analytical method and of the recent extensions to the underpinning analytical ion chemistry required to realize more robust analyses. The challenge of breath analysis is given special attention because, when achieved, it renders analysis of other air media relatively straightforward. Brief overviews are given of recent SIFT-MS breath analyses by leading research groups, noting the desirability of detection and quantification of single volatile biomarkers rather than reliance on statistical analyses, if breath analysis is to be accepted into clinical practice. A 'strengths, weaknesses, opportunities and threats' analysis of SIFT-MS is made, which should help to increase its utility for trace gas analysis.

Contribution of post-harvest agricultural paddy residue fires in the N.W. Indo-Gangetic Plain to ambient carcinogenic benzenoids, toxic isocyanic acid and carbon monoxide.

In the north west Indo-Gangetic Plain (N.W.IGP), large scale post-harvest paddy residue fires occur every year during the months of October-November. This anthropogenic perturbation causes contamination of the atmospheric environment with adverse impacts on regional air quality posing health risks for the population exposed to high concentrations of carcinogens such as benzene and toxic VOCs such as isocyanic acid. These gases and carbon monoxide are known to be emitted from biomass fires along with acetonitrile. Yet no long-term in-situ measurements quantifying the impact of this activity have been carried out in the N.W. IGP. Using high quality continuous online in-situ measurements of these gases at a strategic downwind site over a three year period from 2012 to 2014, we demonstrate the strong impact of this anthropogenic emission activity on ambient concentrations of these gases. In contrast to the pre-paddy harvest period, excellent correlation of benzenoids, isocyanic acid and CO with acetonitrile (a biomass burning chemical tracer); (r≥0.82) and distinct VOC/acetonitrile emission ratios were observed for the post-paddy harvest period which was also characterized by high ambient concentrations of these species. The average concentrations of acetonitrile (1.62±0.18ppb), benzene (2.51±0.28ppb), toluene (3.72±0.41ppb), C8-aromatics (2.88±0.30ppb), C9-aromatics (1.55±0.19ppb) and CO (552±113ppb) in the post-paddy harvest periods were about 1.5 times higher than the annual average concentrations. For isocyanic acid, a compound with both primary and secondary sources, the concentration in the post-paddy harvest period was 0.97±0.17ppb. The annual average concentrations of benzene, a class A carcinogen, exceeded the annual exposure limit of 1.6ppb at NTP mandated by the National Ambient Air Quality Standard of India (NAAQS). We show that mitigating the post-harvest paddy residue fires can lower the annual average concentration of benzene and ensure compliance with the NAAQS. Calculations of excessive lifetime cancer risk due to benzene amount to 25 and 10 per million inhabitants for children and adults, respectively, exceeding the USEPA threshold of 1 per million inhabitants. Annual exposure to isocyanic acid was close to 1ppb, the concentration considered to be sufficient to enhance risks for cardiovascular diseases and cataracts. This study makes a case for urgent mitigation of post-harvest paddy residue fires as the unknown synergistic effect of multi-pollutant exposure due to emissions from this anthropogenic source may be posing grave health risks to the population of the N.W. IGP.

Occurrence and health risk assessment of halogenated disinfection byproducts in indoor swimming pool water.

Swimming pool disinfection byproducts (DBPs) have become a concern in many countries all over the world. In this study, the concentrations of several categories of DBPs, including trihalomethanes (THMs), haloacetic acids (HAAs), haloacetonitriles (HANs), haloketones (HKs) and trichloronitromethane (TCNM), in 13 public indoor swimming pools in Nanjing, China were determined, the correlations between DBPs and water quality parameters as well as between different DBP categories were evaluated, and the health risks of the DBPs to human were examined. The results indicate that the DBP levels in the swimming pools in Nanjing were relatively high, with HAAs as the most dominant category, followed by THMs, HANs, HKs and TCNM sequentially. Bromochloroacetic acid (BCAA), trichloromethane (TCM), dichloroacetonitrile (DCAN), and 1,1,1-trichloropropanone (1,1,1-TCP) were the most dominant species among HAAs, THMs, HANs, and HKs, respectively. For all the different categories of DBPs, the concentrations in the pool disinfected with ozonation/chlorination were lower than those in the pool disinfected with chlorination. The DBP levels were generally not affected by the number of swimmers and the DBP levels on different dates were relatively stable. Besides, the chlorine residual seemed to be a critical concern in most of the swimming pools in this study. Moreover, there were some correlations between DBPs and water quality parameters as well as between different DBP categories. It is to be noted that the predicted cancer and health risks of the DBPs in these swimming pools were generally higher than the regulatory limits by USEPA, and thus DBPs in these swimming pools should be concerned.