Design of Experimental Approach for Development of Rapid High Performance Liquid Chromatographic Process for Simultaneous Estimation of Metoprolol, Telmisartan, and Amlodipine from Formulation: Greenness and Whiteness Evaluation.

The design of an experimental approach, the Box-Behnken design, was implemented to optimize the chromatographic condition to develop a rapid HPLC procedure for quantification of a ternary mixture of metoprolol (MET), telmisartan (TEL), and amlodipine (AML) from the formulation. The perturbation plots, contour, and 3D response surface pictures were developed to study the impact of each variable on the analytes' retention time and the probable interaction between the parameters with fewer chromatographic runs. The optimized HPLC method separated the three analytes within 5 min with excellent selectivity and peak shape on a Zorbax C18 HPLC column using acetonitrile and phosphate buffer (20 mM, pH 5.8) with isocratic elution at a 1.1 mL/min flowrate. A wavelength 230 nm was utilized to monitor the elute. The validation of proposed method demonstrated a wide linearity range of 10-200 µg/mL for MET and TEL and 5-50 µg/mL for AML along with an excellent correlation coefficient. The correctness of the HPLC approach was further confirmed by excellent recovery of the added amount of analytes utilizing the standard addition technique. The recommended HPLC approach was employed safely for quality assurance of the formulation, because the evaluation of the method's greenness and whiteness confirmed the environmentally friendly nature of the approach.

Fixed Dose Single Tablet Formulation with Differential Release of Amlodipine Besylate and Simvastatin and Its Pharmacokinetic Profile: QbD and Risk Assessment Approach.

PURPOSE: A differential release fixed dose matrix tablet of amlodipine besylate (AML-B) and simvastatin (SIM) was formulated to enhance patient compliance. MATERIAL AND METHOD: In the first phase, release controlling parameters of AML-B and SIM granules were identified and in the second phase a fixed dose AML-B and SIM tablet formulation was prepared and optimized for a differential release of the drugs using a quality by design (QbD) and risk assessment approach. A validated HPLC method was employed for simultaneous determination of AML-B and SIM for FDC formulation. A pharmacokinetics of the above drugs was studied in healthy dogs in the third phase. RESULTS: In QbD-based optimized formulation, Eudragit® RSPO-dicalcium phosphate (DCP) blend controlled the release of AML-B over 8 h, though this diffusion-controlled release assumed first order kinetics. DCP and Eudragit® RS 100 also retarded release of SIM causing SIM release over 8 h after AML-B release from the optimized FDC tablet formulation. The HPLC retention times of AML-B and SIM were 2.10 and 15.52 min, respectively. Linearity for AML-B was 5.0-50 ng/mL and 0.01-2.0 µg/mL for SIM with percent recoveries of 92.85-101.53% and 94.51-117.75% for AML-B and SIM. AUC0-∞ of AML-B was increased 3 fold, while AUC0-∞ of SIM was decreased 2 fold. The tmax values for AML-B and SIM were 12 and 6 h, respectively. AML-B was absorbed without any lag time (tlag) while tlag was 6.33 ± 0.81 h for SIM, thus met the study objective. CONCLUSION: The pharmacokinetic study showed an immediate absorption of AML-B while that of SIM was withheld for 6 h, close to the desired delay time of 8 h.

Non-destructive dose verification of two drugs within 3D printed polyprintlets.

Three-dimensional printing (3DP) is a revolutionary technology in pharmaceuticals, enabling the personalisation of flexible-dose drug products and 3D printed polypills (polyprintlets). A major barrier to entry of this technology is the lack of non-destructive quality control methods capable of verifying the dosage of multiple drugs in polyprintlets at the point of dispensing. In the present study, 3D printed films and cylindrical polyprintlets were loaded with flexible, therapeutic dosages of two distinct drugs (amlodipine and lisinopril) across concentration ranges of 1-5% w/w and 2-10% w/w, respectively. The polyprintlets were non-destructively analysed for dose content using a portable near infrared (NIR) spectrometer and validated calibration models were developed using partial least squares (PLS) regression, which showed excellent linearity (R2 Pred = 0.997, 0.991), accuracy (RMSEP = 0.24%, 0.24%) and specificity (LV1 = 82.77%, 79.55%) for amlodipine and lisinopril, respectively. X-ray powder diffraction (XRPD) and thermogravimetric analysis (TGA) showed that sintering partially transformed the phase of both drugs from the crystalline to amorphous forms. For the first time, we report a non-destructive method for quality control of two separate active ingredients in a single 3D printed drug product using NIR spectroscopy, overcoming a major barrier to the integration of 3D printing into clinical practice.

Effect of aging on adsorption behavior of polystyrene microplastics for pharmaceuticals: Adsorption mechanism and role of aging intermediates.

In the environment, aging obviously changes physicochemical properties of microplastics (MPs), but the effects of aging process on adsorption behavior of MPs are not fully understood. In this study, the aging of polystyrene (PS) was accelerated by photo-Fenton reaction. The adsorption mechanism of different aged PS toward atorvastatin (ATV) and amlodipine (AML) and the role of PS-derived intermediates in adsorption process were investigated. Results showed that the adsorption of pristine PS toward pharmaceuticals relied on hydrophobic and π-π interaction, while for aged PS, electrostatic interaction and hydrogen bonding controlled the adsorption. The study revealed that the intermediates released from aging process in high concentration (TOC of 10 mg/L) significantly decreased the adsorption of ATV (10 mg/L) on PS (5.0 g/L) but increased the adsorption of AML (10 mg/L). However, those intermediates at environmental concentration (0.1 mg/L) exhibited low effects on adsorption of pharmaceuticals (1.0 mg/L) on MPs (0.5 g/L of PS). The impact mainly depended on electrostatic interaction between MPs and aging intermediates. Besides, the adsorption of low-degree aged PS was more susceptible to the aging intermediates than that of high-degree aged ones. These findings highlight significant implication of MP-derived intermediates in aquatic environments.

Preparation and Evaluation of Poly-γ-glutamic Acid Hydrogel Mixtures with Amlodipine Besylate: Effect on Ease of Swallowing and Taste Masking.

The purpose of the study was to prepare a poly-γ-glutamic acid hydrogel (PGA gel), to evaluate physicochemical properties, its ease of swallowing using texture profile analysis (TPA) and its taste-masking effects on amlodipine besylate (AML) using the artificial taste sensor and human gustatory sensation testing. Using TPA, 0.5 and 1.0% (w/v) PGA gels in the absence of drug were within the range of acceptability for use in people with difficulty swallowing according to permission criteria published by the Japanese Consumers Affairs Agency. The elution of AML from prepared PGA gels was complete within an hour and the gel did not appear to influence the bioavailability of AML. The sensor output of the basic bitterness sensor AN0 in response to AML mixed with 0.5 and 1.0% PGA gels was suppressed to a significantly greater degree than AML mixed with 0.5 and 1.0% agar. In human gustatory sensation testing, 0.5 and 1.0% PGA gels containing AML showed a potent bitterness-suppressing effect. Finally, 1H-NMR spectroscopic analysis was carried out to examine the mechanism of bitterness suppression when AML was mixed with PGA gel. The signals of the proton nearest to the nitrogen atom of AML shifted clearly upfield, suggesting an interaction between the amino group of AML and the carboxyl group of PGA gel. In conclusion, PGA gel is expected to be a useful excipient in formulations of AML, not only increasing ease of swallowing but also masking the bitterness of the basic drug.

Maltodextrin-modified graphene oxide for improved enantiomeric separation of six basic chiral drugs by open-tubular capillary electrochromatography.

An electrochromatographic capillary was modified with graphene oxide (GO), and the coating was characterized by scanning electron microscopy, energy dispersive X-ray spectrometry, and Fourier transform infrared spectra. By utilizing maltodextrin (MD) as the chiral selector, the basic chiral drugs nefopam (NEF), amlodipine (AML), citalopram hydrobromide (CIT), econazole (ECO), ketoconazole (KET) and cetirizine hydrochloride (CET) can be enantiomerically separated on this CEC. Compared with an uncoated silica capillary, the resolutions are markedly improved (AML: 0.32 → 1.45; ECO: 0.55 → 1.89; KET: 0.88 → 4.77; CET: 0.81 → 2.46; NEF: 1.46 → 2.83; CIT: 1.77 → 4.38). Molecular modeling was applied to demonstrate the mechanism of enantioseparation, which showed a good agreement with the experimental results. Graphical abstractSchematic representation of the preparation of graphene oxide-modified capillary (GO@capillary) for enantioseparation of drug enantiomers. The monolayered GO was used as the coating of the GO@capillary. Then the capillary was applied to construct capillary electrochromatography system with maltodextrin for separation of basic chiral drugs.

UHPLC-MS/MS assay for simultaneous determination of amlodipine, metoprolol, pravastatin, rosuvastatin, atorvastatin with its active metabolites in human plasma, for population-scale drug-drug interactions studies in people living with HIV.

Thanks to highly active antiretroviral treatments, HIV infection is now considered as a chronic condition. Consequently, people living with HIV (PLWH) live longer and encounter more age-related chronic co-morbidities, notably cardiovascular diseases, leading to polypharmacy. As the management of drug-drug interactions (DDIs) constitutes a key aspect of the care of PLWH, the magnitude of pharmacokinetic DDIs between cardiovascular and anti-HIV drugs needs to be more thoroughly characterized. To that endeavour, an UHPLC-MS/MS bioanalytical method has been developed for the simultaneous determination in human plasma of amlodipine, metoprolol, pravastatin, rosuvastatin, atorvastatin and its active metabolites. Plasma samples were subjected to protein precipitation with methanol, followed by evaporation at room temperature under nitrogen of the supernatant, allowing to attain measurable plasma concentrations down to sub-nanogram per milliliter levels. Stable isotope-labelled analytes were used as internal standards. The five drugs and two metabolites were analyzed using a 6-min liquid chromatographic run coupled to electrospray triple quadrupole mass spectrometry detection. The method was validated over the clinically relevant concentrations ranging from 0.3 to 480 ng/mL for amlodipine, atorvastatin and p-OH-atorvastatin, and 0.4 to 480 ng/mL for pravastatin, 0.5 to 480 ng/mL for rosuvastatin and o-OH-atorvastatin, and 3 to 4800 ng/mL for metoprolol. Validation performances such as trueness (95.4-110.8%), repeatability (1.5-13.4%) and intermediate precision (3.6-14.5%) were in agreement with current international recommendations. Accuracy profiles (total error approach) were lying within the limits of ±30% accepted in bioanalysis. This rapid and robust UHPLC-MS/MS assay allows the simultaneous quantification in plasma of the major currently used cardiovascular drugs and offers an efficient analytical tool for clinical pharmacokinetics as well as DDIs studies.

A new strategy for taste masking on bitter drug by other combined drug in fixed-dose combination: bitterness of Amlodipine besylate could be masked efficiently by Valsartan.

OBJECTIVES: The aim of this study was to evaluate the bitterness of amlodipine besylate (AML) combined with other five antihypertensive drugs: alacepril, benazepril, hydrochlorothiazide, telmisartan (TEL) and valsartan (VAL), which have possibility of usage as a fixed-dose combination (FDC) drugs. METHODS: The bitterness of individual six drugs and AML combined with each of the five drugs was evaluated using taste sensor SA402B (Intelligent Sensor Technology Inc.). AML combined with TEL or VAL was evaluated by taste sensor and human gustatory sensation tests. The interaction between AML with TEL or VAL was evaluated by 1 H-NMR. KEY FINDINGS: The bitterness of AML was significantly decreased by addition of VAL, whereas it remained unchanged by the addition of TEL in taste sensor and human gustatory sensation test. In the 1 H-NMR spectrum of AML with VAL, signal shifts of protons in AML were observed compared to that in AML alone. On the other hand, in the 1 H-NMR spectrum of AML with TEL, signal shifts of protons in AML were not observed. CONCLUSIONS: It was suggested that when VAL was mixed with AML, the electrostatic interactions between positive charged amino group of AML and negative charged tetrazole group of VAL were caused, and thereby led the suppression the bitterness of AML.

Simulated space radiation: Investigating ionizing radiation effects on the stability of amlodipine besylate API and tablets.

Efficacious pharmaceuticals with the adequate shelf life are essential for the well-being of the space explorers and successful completion of a space mission. Space is brimming with different types of radiations, which penetrate inside the spacecraft despite the shielding material. Such radiations can alter the stability of the pharmaceuticals during long duration space missions. The literature reporting the space radiation effects on the pharmaceuticals is scarce in a public domain. Ground-based simulation studies can be useful to predict the influence of the space radiations on the stability of the pharmaceuticals. Based upon these facts, the main objective of the present preliminary work was to investigate the effect of different types of ionizing radiations on the stability of amlodipine besylate API and tablets. Amlodipine besylate samples were irradiated by protons, neutrons (thermal and fast), gamma and heavy ion (56Fe) radiations with their different doses. The samples were also irradiated with UV-visible radiation to compare the effect of selected ionizing radiations with photodegradation. The physical stability was examined through organoleptic evaluation and the chemical stability was evaluated by FTIR and HPLC. The results of the organoleptic evaluation showed colour changes from colourless to yellow in proton irradiated solid API and gamma irradiated API aqueous solution. The FTIR spectrum of proton irradiated API showed one additional absorption band at 1728 cm-1 due to degradation products. HPLC analysis revealed that amlodipine degraded up to 10% and 21% after the highest doses of proton and gamma irradiation, respectively. No physical or chemical changes were observed after neutron and 56Fe irradiation. The structures of major radiolytic products were elucidated using LC-MS/MS. Two new impurities were found in the API aqueous solution as a result of gamma irradiation. The drug degradation pathways were postulated by proposing the plausible mechanism of formation.

Metal organic framework HKUST-1 modified with carboxymethyl-ß-cyclodextrin for use in improved open tubular capillary electrochromatographic enantioseparation of five basic drugs.

This work shows that the metal organic framework (MOF) HKUST-1 of type Cu3(BTC)2 (also referred to as MOF-199; a face-centered-cubic MOF containing nanochannels) is a most viable coating for use in enantioseparation in capillary electrochromatography (CEC). A HKUST-1 modified capillary was prepared and characterized by scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectra, elemental analysis and thermogravimetric analysis. CEC-based enantioseparation of the basic drugs propranolol (PRO), esmolol (ESM), metoprolol (MET), amlodipine (AML) and sotalol (SOT) was performed by using carboxymethyl-ß-cyclodextrin as the chiral selector. Compared with a fused-silica capillary, the resolutions are improved (ESM: 1.79; MET: 1.80; PRO: 4.35; SOT: 1.91; AML: 2.65). The concentration of chiral selector, buffer pH value, applied voltage and buffer concentration were optimized, and the reproducibilities of the migration times and Rs values were evaluated. Graphical abstract Schematic presentation of the preparation of a HKUST-1@capillary for enantioseparation of racemic drugs. Cu(NO3)2 and 1,3,5-benzenetricarboxylic acid (BTC) were utilized to prepare the HKUST-1@capillary. Then the capillary was applied to construct capillary electrochromatography system with carboxymethyl-ß-cyclodextrin (CM-ß-CD) for separation of basic racemic drugs.

Study of Interactions between Amlodipine and Quercetin on Human Serum Albumin: Spectroscopic and Modeling Approaches.

The aim of this study was to analyze the binding interactions between a common antihypertensive drug (amlodipine besylate-AML) and the widely distributed plant flavonoid quercetin (Q), in the presence of human serum albumin (HSA). Fluorescence analysis was implemented to investigate the effect of ligands on albumin intrinsic fluorescence and to define the binding and quenching properties. Further methods, such as circular dichroism and FT-IR, were used to obtain more details. The data show that both of these compounds bind to Sudlow's Site 1 on HSA and that there exists a competitive interaction between them. Q is able to displace AML from its binding site and the presence of AML makes it easier for Q to bind. AML binds with the lower affinity and if the binding site is already occupied by Q, it binds to the secondary binding site inside the same hydrophobic pocket of Sudlow's Site 1, with exactly the same affinity. Experimental data were complemented with molecular docking studies. The obtained results provide useful information about possible pharmacokinetic interactions upon simultaneous co-administration of the food/dietary supplement and the antihypertensive drug.

Evidence of human-like Ca2+ channels and effects of Ca2+ channel blockers in Acanthamoeba castellanii.

The evolution of voltage-gated calcium channel (Cav) in eukaryotes is an area of interest for biologists worldwide. The CLAN CL0030 and its family Ion_Trans 2 PF 07885 have been known to be present in prokaryotes, but the origin of these ion channels in Acanthamoeba spp. is yet to be determined. We inferred the origin of primitive forms of two-pore channels like proteins, human-like Cav 1.1 of L-type, and Cav subunit alpha-2/delta-1 in Acanthamoeba spp. early during evolution. By in-depth investigation into genomics, transcriptomics, use of bioinformatics tools and experimentations done with drugs like amlodipine and gabapentin on Acanthamoeba spp., we show the evidence of primitive forms of these channels in this protist pathogen. Genomics and transcriptomics of proteins ACA1_167020, 092610, and 270170 reflected their cellular expression in Acanthamoeba spp. We performed amino acid sequence homology, 3D structural modeling, ligand binding predictions, and dockings. Bioinformatics and 3D structural models show similarities between ACA1_167020, 092610, 270170, and different types of known human Cav. We show amoebicidal effects of amlodipine and gabapentin on Acanthamoeba spp., which can help design their structural analogs to target pathogenic genotypes of Acanthamoeba in diseases like Acanthamoeba keratitis and granulomatous amoebic encephalitis.

'Temporary Plasticiser': A novel solution to fabricate 3D printed patient-centred cardiovascular 'Polypill' architectures.

Hypertension and dyslipidaemia are modifiable risk factors associated with cardiovascular diseases (CVDs) and often require a complex therapeutic regimen. The administration of several medicines is commonly associated with poor levels of adherence among patients, to which World Health Organisation (WHO) proposed a fixed-dose combination unit (polypill) as a strategy to improve adherence. In this work, we demonstrate the fabrication of patient-specific polypills for the treatment of CVDs by fused deposition modelling (FDM) 3D printing and introduce a novel solution to meet critical quality attributes. The construction of poly(vinyl alcohol) (PVA)-based polypills containing four model drugs (lisinopril dihydrate, indapamide, rosuvastatin calcium and amlodipine besylate) was revealed for the first time. The impact of tablet architecture was explored using multi-layered and unimatrix structures. The novel approach of using distilled water as a 'temporary co-plasticiser' is reported and was found to significantly lower the extruding (90 °C) and 3D printing (150 °C) temperatures from 170 °C and 210 °C respectively, with consequent reduction in thermal stress to the chemicals. XRD indicated that lisinopril dihydrate and amlodipine besylate maintained their crystalline form while indapamide and rosuvastatin calcium were essentially in amorphous form in the PVA tablets. From the multilayer polypills, the release profile of each drug was dependent on its position in the multilayer. In addition to the multilayer architecture offering a higher flexibility in dose titration and a more adaptive solution to meet the expectations of patient-centred therapy, we identify that it also allows orchestrating the release of drugs of different physicochemical characteristics. Adopting such an approach opens up a pathway towards low-cost multidrug delivery systems such as tablets, stents or implants for wider range of globally approved actives.

Drug-in-mucoadhesive type film for ocular anti-inflammatory potential of amlodipine: Effect of sulphobutyl-ether-beta-cyclodextrin on permeation and molecular docking characterization.

Mucoadhesive type ocular film has been prepared for studying the anti-inflammatory potential of amlodipine (AML) on carrageenan-induced rabbit model and the effect of sulphobutyl-ether-beta-cyclodextrin on corneal permeation was tested. Hydroxypropyl methylcellulose (HPMC) ocular film was prepared after complexation of amlodipine with ß-cyclodextrin, (BCD), hydroxypropyl ß-cyclodextrin (HPCD), and sulfobutylether ß-cyclodextrin (SBCD). The film without cyclodextrin showed a maximum swelling, and erosion to the highest extent. Both drug release and permeation were highly diffusion controlled and highest improvement was observed with SBCD due to increased dissolution, compared to other formulations with or without cyclodextrin. Highest binding energy and highest extent of amorphization were noticed in the SBCD film formulation. Improved amlodipine release in-vitro and ocular permeation were found by the HPMC film formulation after complexation of the drug with cyclodextrins wherein SBCD exhibited both to the highest extent. Binary and ternary systems molecular docking studies confirmed the lowest energy of binding between amlodipine and BCD compared to HBCD and SBCD. Signs of acute inflammation were mitigated within 2 h of film application in the cul-de-sac. Presence of sulphobutyl-ether ß-cyclodextrin in the amlodipine-HPMC film can improve ocular permeation significantly and could be utilized as mucoadhesive type formulation for anti-inflammatory activity.

Molecular dynamics, physical and thermal stability of neat amorphous amlodipine besylate and in binary mixture.

In this paper, a stable amorphous solid dispersion of an antihypertensive drug, amlodipine besylate (AMB) was prepared by entrapping it in a polymer matrix, polyvinyl pyrrollidone, in different weight ratios (AMB/PVP 05:95, 10:90, 20:80, 30:70). The glass forming ability of all binary dispersions were studied by means of differential scanning calorimetry and found good correlation between experimental Tg and Fox Flory's prediction. By considering the daily dosage limit of 5 mg, a weight ratio of 05:95 was further considered for the study. The structures of neat and binary of AMB were characterized by density functional theory, Fourier transform infrared spectroscopy, Fourier transform Raman spectroscopy and UV-visible spectroscopy. Further, detailed molecular dynamics of both pure and binary were investigated using broadband dielectric spectroscopy to judge the physical stability of the amorphous dispersions. Translation-rotation coupling of AMB possibly explains the dual conductivity and dipolar nature of the secondary relaxation in neat AMB. Thus, the binary dispersion of AMB with commercially acceptable weight ratio with strong glass forming behaviour and better shelf life was prepared and characterized for practical applications.

Quantification of amlodipine and atorvastatin in human plasma by UPLC-MS/MS method and its application to a bioequivalence study.

A robust, rapid and sensitive UPLC-MS/MS method has been developed, optimized and validated for the determination of amlodipine (AML) and atorvastatin (ATO) in human plasma using eplerenone as an internal standard (IS). Multiple-reaction monitoring in positive electrospray ionization mode was utilized in Xevo TQD LC-MS/MS. Double extraction was used in sample preparation using diethyl ether and ethyl acetate. The prepared samples were analyzed using an Acquity UPLC BEH C18 (50 × 2.1 mm, 1.7 µm) column. Ammonium formate and acetonitrile, pumped isocraticaly at a flow rate of 0.25 mL/min, were used as a mobile phase. Method validation was done as per the US Food and Drug Administration guidelines. Linearity was achieved in the range of 0.1-10 ng/mL for AML and 0.05-50 ng/mL for ATO. Intra-day and inter-day accuracy and precision were calculated and found to be within the acceptable range. A short run time, of <1.5 min, permits analysis of a large number of plasma samples per batch. The developed and validated method was applied to estimate AML and ATO in a bioequivalence study in healthy human volunteers.

Influence of Amlodipine Enantiomers on Human Microsomal Cytochromes P450: Stereoselective Time-Dependent Inhibition of CYP3A Enzyme Activity.

Amlodipine (AML) is available as a racemate, i.e., a mixture of R- and S-enantiomers. Its inhibitory potency towards nine cytochromes P450 (CYP) was studied to evaluate the drug-drug interactions between the enantiomers. Enzyme inhibition was evaluated using specific CYP substrates in human liver microsomes. With CYP3A, both enantiomers exhibited reversible and time-dependent inhibition. S-AML was a stronger reversible inhibitor of midazolam hydroxylation: the Ki values of S- and R-AML were 8.95 µM, 14.85 µM, respectively. Computational docking confirmed that the enantiomers interact differently with CYP3A: the binding free energy of S-AML in the active site was greater than that for R-AML (-7.6- vs. -6.7 kcal/mol). Conversely, R-AML exhibited more potent time-dependent inhibition of CYP3A activity (KI 8.22 µM, Kinact 0.065 min-1) than S-AML (KI 14.06 µM, Kinact 0.041 min-1). R-AML was also a significantly more potent inhibitor of CYP2C9 (Ki 12.11 µM/S-AML 21.45 µM) and CYP2C19 (Ki 5.97 µM/S-AML 7.22 µM. In conclusion, results indicate that clinical use of S-AML has an advantage not only because of greater pharmacological effect, but also because of fewer side effects and drug-drug interactions with cytochrome P450 substrates due to absence of R-AML.

Validated LC-MS/MS Method for the Simultaneous Determination of Amlodipine and Its Major Metabolites in Human Plasma of Hypertensive Patients.

BACKGROUND: No information on the pharmacokinetic characteristics of amlodipine (AML) metabolites is available. This study aimed to develop a method based on isocratic liquid chromatography coupled to tandem mass spectrometry for the simultaneous determination of AML and its 2 major metabolites, dehydroamlodipine (DH-AML) and O-des[2-aminoethyl]-O-carboxymethyl DH-AML (CM-DH-AML), and to use it for monitoring this drug in hypertensive patients. METHODS: Acetonitrile-deproteinized plasma specimens were separated using an octadecyl-silica column (3-µm particle size) with a mobile phase consisting of 50% methanol containing 0.15% of formic acid in water. The run time was 9 minutes. The mass spectrometer was run in the positive ion electrospray ionization mode. This method was applied for the determination of AML and its metabolites in plasma samples from patients treated with this drug. RESULTS: The calibration curves in human plasma of AML, DH-AML, and CM-DH-AML were linear over the concentration ranges of 0.5-64, 1-64, and 0.5-64 ng/mL, respectively, and their lower limits of quantification were 0.5, 1, and 0.5 ng/mL, respectively. Their extraction recovery rates and matrix factors in human plasma were 94.8%-109.0% and 97.0%-101.4%, respectively. The intra-assay and interassay imprecisions and accuracies were within 10.8% and 95.4%-111.2%, respectively. The plasma concentration ranges of AML, DH-AML, and CM-DH-AML were 6.5-20.9, 1.4-10.9, and 5.6-38.3 ng/mL, respectively. CONCLUSIONS: The present method with acceptable analytical performance can be helpful for monitoring the plasma concentration of AML, including the determination of its metabolites in patients with hypertension.

Introduction of agarose gel as a green membrane in electromembrane extraction: An efficient procedure for the extraction of basic drugs with a wide range of polarities.

Developing green methods for analyte extraction is one of the most important topics in the field of sample preparation. In this study, for the first time, agarose gel was used as membrane in electromembrane extraction (EME) without using any organic solvent, for the extraction of four model basic drugs (rivastigmine (RIV), verapamil (VER), amlodipine (AML), and morphine (MOR)) with a wide polarity window (log P from 0.43 to 3.7). Different variables playing vital roles in the proposed method were evaluated and optimized. As a driving force, a 25V electrical field was applied to make the analyte migrate from sample solution with pH 7.0, through the agarose gel 3% (w/v) with 5mm thickness, into an acceptor phase (AP) with pH 2.0. The best extraction efficiency was obtained with an extraction duration of 25min. With this new methodology, MOR with high polarity (log P=0.43) was efficiently extracted without using any carrier or ion pair reagents. Limits of detection (LODs) and quantification (LOQs) were in the ranges of 1.5-1.8ngmL-1 and 5.0-6.0ngmL-1, respectively. Finally, the proposed method was successfully applied to determine concentrations of the model drugs in the wastewater sample.

Molecular insight into atypical instability behavior of fixed-dose combination containing amlodipine besylate and losartan potassium.

Combination therapy with the use of fixed-dose combinations (FDCs) is evincing increasing interest of prescribers, manufacturers and even regulators, evidently due to the primary benefit of improved patient compliance. However, owing to potential of drug-drug interaction, FDCs require closer scrutiny with respect to their physical and chemical stability. Accordingly, the purpose of the present study was to explore stability behavior of a popular antihypertensive combination of amlodipine besylate (AML) and losartan potassium (LST). Physical mixtures of the two drugs and multiple marketed formulations were stored under accelerated conditions of temperature and humidity (40°C/75% RH) in a stability chamber and samples were withdrawn after 1 and 3 months. The physical changes were observed visibly, while chemical changes were monitored by HPLC employing a method that could separate the two drugs and all other components present. The combination revealed strong physical instability and also chemical degradation of AML in the presence of LST. Interestingly, three isomeric interaction products of AML were formed in the combination, which otherwise were reported in the literature to be generated on exposure of AML free base above its melting point. The same unusual products were even formed when multiple marketed FDCs were stored under accelerated conditions outside their storage packs. However, these were absent when AML alone was stored in the same studied conditions. Therefore, reasons for physical and chemical incompatibility and the mechanism of degradation of AML in the presence of LST were duly explored at the molecular level. The outcomes of the study are expected to help in development of stable FDCs of the two drugs.