A multiresidue method for the analysis of pesticides, polycyclic aromatic hydrocarbons, and polychlorinated biphenyls in snails used as environmental biomonitors.

This paper reports an optimized multiresidue extraction strategy based on the Quick, Easy, Cheap, Effective, Rugged, and Safe (QuEChERS) extraction procedure and on solid-phase microextraction (SPME) for the simultaneous screening of 120 pesticides, 16 polycyclic aromatic hydrocarbons, and 22 polychlorinated biphenyls from the terrestrial snail Helix aspersa. The optimized extraction method was based on QuEChERS using acetonitrile, followed by dispersive-Solid-phase extraction clean-up using primary secondary amine and octadecyl (C18) sorbents. The obtained extracts were analyzed by liquid chromatography coupled with tandem mass spectrometry and gas chromatography coupled with tandem mass spectrometry. This latest technique was preceded by a pre-concentration step using SPME with appropriate fibers. Afterwards, the method was validated for its linearity, sensitivity, recovery, and precision. Results showed high sensitivity, accuracy, and precision, with limits of detection and quantification lower than 20 ng g - 1 for most considered pollutants. Both inter and intra-day analyses revealed low relative standard deviation (%), which was lower than 20% for most targeted compounds. Moreover, the obtained regression coefficient (R2) was higher than 0.98 and the recoveries were higher than 60% for the majority of the assessed pollutants.

Label-free and highly selective electrochemical aptasensor for detection of PCBs based on nickel hexacyanoferrate nanoparticles/reduced graphene oxides hybrids.

In consideration of the urgent need to determine polychlorinated biphenyls (PCBs) in the environment, a label-free and highly selective electrochemical aptasensor was constructed for determining PCBs based on nickel hexacyanoferrate nanoparticles (NiHCF NPs)/reduced graphene oxides (rGO) hybrids. NiHCF NPs/rGO hybrids with small size of about 5 nm NiHCF NPs were synthesized for the first time by in situ co-deposition of NiHCF NPs on rGO surface. In the hybrids, rGO with large area and good conductivity can supply more space for loading NiHCF NPs and improve the conductivity of the hybrids. NiHCF NPs that can be used to be act as a signal probe exhibit a couple of well-defined peaks with highly reversible redox ability and good stability. Here, PCB77 as a model molecule, the anti-PCB77 aptamer was anchored on the NiHCF NPs/rGO hybrids by covalent bonding reaction. The design aptasensor for detecting PCB77 exhibits a favorable linear response from 1.0 to 100.0 ng/L with a low detection limit of 0.22 ng/L. Meanwhile, it displays good selectivity for PCB77 detection due to the specificity and high affinity of aptamer to PCB77. Additionally, the application of the aptasensor was evaluated in real environmental samples.

Ultra-high thermal stability perarylated ionic liquids as gas chromatographic stationary phases for the selective separation of polyaromatic hydrocarbons and polychlorinated biphenyls.

Ionic liquids (ILs) are well-known in the field of separation science for their unique selectivity when used as stationary phases in gas chromatography (GC). While a significant amount of knowledge has been attained in correlating structural features of an IL to separation selectivity, developments in producing IL-based stationary phases suitable for high temperature GC studies have lagged behind. Column bleed is a result of the stationary phase undergoing volatilization/decomposition at high temperatures and is undesirable in separations coupled to GC/MS. It has been well-known that traditional classes of ILs with long alkyl side chain substituents are susceptible to Hofmann elimination at elevated temperatures. In this study, a new class of IL stationary phases containing perarylated cations exhibiting improved thermal stability are introduced. These ILs were used to prepare wall-coated open tubular columns with high column efficiency and produced very low bleed at temperatures up to 350 °C. Their unique chemical structures provide stronger π-π interactions compared to many commercially-available stationary phases. To exploit the unique interactions provided by these stationary phases, the separation of two classes of environmentally hazardous aromatic compounds, namely, polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs), was examined. Both classes of compounds contain structural isomers with high boiling points that are often challenging to separate. The perarylated sulfonium and phosphonium IL-based stationary phases exhibited excellent thermal stability as well as unique selectivity toward isomers of PAHs as well as toxic PCB analyte pairs.

Direct immersion solid-phase microextraction analysis of multi-class contaminants in edible seaweeds by gas chromatography-mass spectrometry.

The present work aimed at the development of a simple and accurate direct immersion-solidphase microextraction-gas-chromatography-mass spectrometry (DI-SPME-GC-MS) method for simultaneous determination of PAHs, PCBs, and pesticide residues in edible seaweeds. As the target contaminants possess a wide range of physical-chemical properties, multivariate experimental design was used for method optimization. In particular, two different methods were optimized and validated: one that allows for simultaneous determination of all targets, and an ad hoc method for determination of hydrophobic analytes, a class that often poses a challenge for extraction from food matrices. Optimum conditions suitable for simultaneous quantitation of all targeted compounds, namely buffer at pH = 7.0, 20% acetone (v/v), 10% NaCl (w/w), 0.02% NaN3, 60 min DI extraction at 55 °C, and 20 min desorption at 270 °C, afforded limits of quantitation (LOQs) in the range of 1-30 µg kg-1, a wide linear range of 5-2000 µg kg-1, the attainment of satisfactory determination coefficients (R2˃0.99) with no significant lack of fit (p > 0.05) at the 5% level, and satisfactory accuracy and precision values. By modifying the extraction conditions to favor extraction of the most hydrophobic analytes (e.g. higher amount of organic modifier and pH, and lower salt content) lower LOQs were obtained for these compounds ranging from 0.2 to 13.3 µg kg-1. The established methods were then used for screening of commercial, edible dry seaweeds, with PCBs (≤16.0 ng g-1) and PAHs (≤15.5 ng g-1) detected in some samples. This method overcomes most challenges commonly encountered in dry sample analysis applications, and represents the first report of a DI-SPME method employing the matrix-compatible fiber for simultaneous multiclass and multiresidue analysis of seaweeds.

Metal-organic framework-coated stainless steel fiber for solid-phase microextraction of polychlorinated biphenyls.

For solid phase microextraction (SPME), effective immobilization of sorbent on a stainless steel fiber surface is very essential. But, it still remains challenging because the chemical inertness of stainless steel fiber. In this work, chemical bonding method was introduced to fabricate a series of metal-organic frameworks (MOFs)-coated stainless steel fibers, and some representative MOFs (ZIF-90 (Zn), MOF-199 (Cu), MIL-101 (Cr), MOF-5 (Zn))-coated stainless steel fibers were successfully synthesized. Such strategy can noticeably increase the mechanical and chemical stability, and prolong the service lifetime due to it combine the advantages of stainless steel fiber and chemical bonding method. The stability of MOF-ZIF-90 (Zn)-coated stainless steel fibers which were preparated by different methods (chemical bonding method, adhesive method and deposition method) were studied, and results showed the chemical bonding method proved the best stability. Based on the ZIF-90 (Zn)-coated fiber, the SPME-GC-MS method was developed for detecting traces of polychlorinated biphenyls (PCBs) and satisfactory results were obtained. The linear ranges were 0.01-600 ng L-1 and the coefficient of determination was higher than 0.993. The limits of detection for the PCBs were 0.0013-0.053 ng L-1. The recoveries for the spiked PCBs in the Minjiang water, soil and vegetable oil samples were in the range of 85.9-105.8%. The extraction capacity of the ZIF-90 (Zn)-coated stainless steel fiber prepared by chemical bonding method did not show measurable change under different temperatures or organic solvents for up to 5 days.

Evaluation of ionic liquid gas chromatography stationary phases for the separation of polychlorinated biphenyls.

The feasibility of six ionic liquid- (IL-) based stationary phases for the analysis of environmentally important polychlorinated biphenyls (PCBs) by gas chromatography combined with either electron capture micro-detector (GC-micro-ECD) or quadrupole mass spectrometry (GC-MS, for confirmation) have been evaluated. These IL-based columns showed a separation mechanism different from that observed for other commercial phases, such a low bleed high temperature 8% phenyl (equiv.) polycarborane-siloxane suggested shape-selective phase for non-ortho and mono-ortho-CBs, HT-8, or a polar poly(ethylene glycol), resulting in a different elution order of the 69 investigated PCBs. However, no all phases provided equality satisfactory resolutions for the most environmentally relevant congeners, the 12 toxic and the 7 priority PCBs. From this point of view, the best results were obtained with the SLB-IL76 and SLB-IL59 phases, which showed a number of coelutions for these specific congeners only slightly higher to that observed on HT-8. Interestingly, the SLB-IL59 phase was the only one among the evaluated phases allowing a complete resolution of the most toxic non-ortho substituted congeners # 77, 126 and 169 from all other PCBs investigated. SLB-IL76 and SLB-IL59 also demonstrated a superior chromatographic performance concerning peak symetry, retention time stability and column bleeding, compared to the other four IL-based columns evaluated. Altogether, results obtained for the analysis of pure standards illustrated the potential of, in particular, SLB-IL 59 as an alternative phase for confirmation of the identity of PCBs typically detected in environmental matrices that coeluted on conventional non-polar phases in use for this type of determination. However, the long-term stability and quantitative behaviour of these stationary phases during the analysis of real samples still need to be addressed.

Organochlorine pesticides accumulation and breast cancer: A hospital-based case-control study.

The aim of this study is to detect the accumulation status of organochlorine pesticides in breast cancer patients and to explore the relationship between organochlorine pesticides contamination and breast cancer development. We conducted a hospital-based case-control study in 56 patients with breast cancer and 46 patients with benign breast disease. We detected the accumulation level of several organochlorine pesticides products (ß-hexachlorocyclohexane, γ-hexachlorocyclohexane, polychlorinated biphenyls-28, polychlorinated biphenyls-52, pentachlorothioanisole, and pp'-dichlorodiphenyldichloroethane) in breast adipose tissues of all 102 patients using gas chromatography. Thereafter, we examined the expression status of estrogen receptor, progesterone receptor, human epidermal growth factor receptor-2 (HER2), and Ki-67 in 56 breast cancer cases by immunohistochemistry. In addition, we analyzed the risk of breast cancer in those patients with organochlorine pesticides contamination using a logistic regression model. Our data showed that breast cancer patients suffered high accumulation levels of pp'-dichlorodiphenyldichloroethane and polychlorinated biphenyls-52. However, the concentrations of pp'-dichlorodiphenyldichloroethane and polychlorinated biphenyls-52 were not related to clinicopathologic parameters of breast cancer. Further logistic regression analysis showed polychlorinated biphenyls-52 and pp'-dichlorodiphenyldichloroethane were risk factors for breast cancer. Our results provide new evidence on etiology of breast cancer.

Stir-bar supported micro-solid-phase extraction for the determination of polychlorinated biphenyl congeners in serum samples.

In present work, a new configuration of micro-solid phase extraction was introduced and termed as stir-bar supported micro-solid-phase extraction (SB-µ-SPE). A tiny stir-bar was packed inside the porous polypropylene membrane along with sorbent material and the edges of membrane sheet were heat sealed to secure the contents. The packing of stir-bar inside the µ-SPE device does not allow the device to stick with the wall or any corner of the sample vial during extraction, which is, however, a frequent observation in routine µ-SPE. Moreover, it enhances effective surface area of the sorbent exposed to sample solution through continuous agitation (motion and rotation). It also completely immerses the SB-µ-SPE device in the sample solution even for non-polar sorbents. Polychlorinated biphenyls (PCBs) were selected as model compounds and the method performance was evaluated in human serum samples. After extraction, samples were analyzed by gas chromatography mass spectrometry (GC-MS). The factors that affect extraction efficiency of SB-µ-SPE were optimized. Under optimum conditions, a good linearity (0.1-100ngmL(-1)) with coefficients of determinations ranging from 0.9868 to 0.9992 was obtained. Limits of detections were ranged between 0.003 and 0.047ngmL(-1). Acceptable values for inter-day (3.2-9.1%) and intra-day (3.1-7.2%) relative standard deviations were obtained. The optimized method was successfully applied to determine the concentration of PCB congeners in human serum samples.

Soil washing in combination with homogeneous Fenton-like oxidation for the removal of 2,4,4'-trichlorodiphenyl from soil contaminated with capacitor oil.

Detoxification by chemical oxidation of polychlorinated biphenyls (PCBs) in contaminated soils is very difficult and inefficient because PCBs typically associate with the solid phase or exist as non-aqueous-phase liquids due to their low solubility and slow desorption rates, and thus, they are difficult to remove from soils by using traditional, water-based elution techniques. Surfactant can enhance washing efficiency of PCBs from contaminated soils. This study used Brij 58, Brij 30, Tween 80, and 2-hydroxypropyl-ß-cyclodextrin (HPCD) to solubilize 2,4,4'-trichlorodiphenyl (PCB28) from soil contaminated with capacitor oil into solution. The feasibility of PCB28 oxidation in soil washing wastewater through a Fe(3+)-catalyzed Fenton-like reaction was subsequently examined. Washing with 10 g L(-1) Brij 58 solution showed the highest extraction efficiency (up to 61.5 %) compared with that of the three other surfactants. The total concentration of PCB28 in contaminated soil at 25 °C after 48-h extraction was 286 mg L(-1). In contrast to conditions in which no washing agent was added, addition of the four washing agents decreased the efficiency of PCB28 degradation by the Fenton-like reaction, with the decrease due to addition of 10 g L(-1) Brij 58 solution being the smallest. The optimal concentration of H2O2 for preventing its useless decomposition was found to be 50 mM. The efficiency of PCB28 removal was lower when the initial concentration of PCB28 treated in the Fenton-like reaction was higher. The degradation efficiencies of PCB28 at initial concentrations of 0.1, 10, and 176 mg L(-1) in 10 g L(-1) Brij 58 solution at 25 °C and pH 3.0 and 9 h of reaction using 50 mM H2O2 were 64.1, 42.0, and 34.6 %, respectively. This result indicates that soil washing combined with Fenton-like oxidation may be a practical approach for the remediation of PCB-contaminated soil.

Pressurized liquid extraction technique for the analysis of pesticides, PCBs, PBDEs, OPEs, PAHs, alkanes, hopanes, and steranes in atmospheric particulate matter.

An analytical method has been developed for the pressurized liquid extraction (PLE) of a wide range of semi-volatile organic compounds (SVOCs) from atmospheric particulate matter. Approximately 130 SVOCs from eight compound classes were selected as molecular markers of (1) agricultural activity (30 current and historic-use pesticides), (2) industrial activity (18 PCBs), (3) consumer products and building materials (16 PBDEs, 11 OPEs), and (4) motor vehicle exhaust (22 PAHs, 16 alkanes, 9 hopanes, 8 steranes). Currently, there is no analytical method validated for the extraction of all eight compound classes in a single automated technique. The extraction efficiencies of varying solvents and solvent combinations at high temperatures and pressures were examined. Extracts were concentrated and analyzed by gas chromatography coupled with mass spectrometry. The optimized PLE method utilized methylene chloride:acetone (2:1 v/v) at 100 °C with three (5 min) static cycles, flush volume of 80%, and a 100 s N2 purge. Spike and recovery experiments (n=7) provided average percent recoveries for pesticides, PCBs, PBDEs, OPEs, PAHs, alkanes, hopanes, and steranes of 88.8±4.0%, 86.9±2.6%, 83.8±2.9%, 101±6%, 90.3±6.1%, 74.4±8.8%, 104±8%, and 86.5±8.6%, respectively. The developed method was applied to atmospheric particulate matter samples collected in the greater Houston, TX metropolitan area. Ambient concentrations of eight classes of compounds (92 SVOCs) were reported in pg m(-3).

A novel reductive graphene oxide-based magnetic molecularly imprinted poly(ethylene-co-vinyl alcohol) polymers for the enrichment and determination of polychlorinated biphenyls in fish samples.

The novel reductive graphene oxide-based magnetic molecularly imprinted poly(ethylene-co-vinyl alcohol) polymers (rGO@m-MIPs) were successfully synthesized as adsorbents for six kinds of polychlorinated biphenyls (PCBs) in fish samples. rGO@m-MIPs was prepared by surface molecular imprinting technique. Besides, Fe3 O4 nanoparticles (NPs) were employed as magnetic supporters, and rGO@Fe3 O4 was in situ synthesis. Different from functional monomer and cross-linker in traditional molecularly imprinted polymer, here, 3,4-dichlorobenzidine was employed as dummy molecular and poly(ethylene-co-vinyl alcohol) was adopted as the imprinted polymers. After morphology and inner structure of the magnetic adsorbent were characterized, the adsorbent was employed for disperse solid phase extraction toward PCBs and exhibited great selectivity and high adsorption efficiency. This material was verified by determination of PCBs in fish samples combined with gas chromatography-mass spectrometry (GC-MS) method. According to the detection, the low detection limits (LODs) of PCBs were 0.0035-0.0070 µg l(-1) and spiked recoveries ranged between 79.90 and 94.23%. The prepared adsorbent can be renewable for at least 16 times and expected to be a new material for the enrichment and determination of PCBs from contaminated fish samples.

Preparation of mesoporous ZrO2-coated magnetic microsphere and its application in the multi-residue analysis of pesticides and PCBs in fish by GC-MS/MS.

A novel mesoporous ZrO2 immobilized magnetic Fe3O4 microsphere (m-ZrO2@Fe3O4) was successfully synthesized and characterized by transmission electron microscope (TEM), X-ray diffractometer (XRD), nitrogen adsorption measurement (NAM), energy-dispersive X-ray analysis (EDX), vibrating sample magnetometer (VSM). Then the resultant m-ZrO2@Fe3O4 and an n-octadecylphosphonic acid modified magnetic microsphere (Fe3O4-OPA) were employed as clean-up co-adsorbents of QuEChERS (Quick, Easy, Cheap, Effective, Rugged, Safe) method for the analysis of 42 pesticides and 7 polychlorinated biphenyls (PCBs) in fish samples. Lipid co-extractives such as fatty acids in QuEChERS extracts could be efficiently removed through the Lewis acid-Lewis base interaction between m-ZrO2@Fe3O4 and carboxylic groups, while some other apolar interferents could be adsorbed through hydrophobic interaction by Fe3O4-OPA. Meanwhile, the magnetic property of adsorbents endows the clean-up procedure with manipulative convenience. Several parameters affecting the clean-up performance were investigated. Under the optimal conditions, the modified QuEChERS method combined with gas chromatography-tandem mass spectrometry (GC-MS/MS) for the multi-class, multi-residue analysis of pesticides and PCBs in fish samples was validated according to linearility, recovery and precision. Good linearities were obtained for all analytes with R(2) larger than 0.9903. Limits of detection (LODs) were found to be in the range of 0.02-4.40 ng/g. The method recoveries of all analytes spiked at three concentration levels in blank fish samples were from 69.8% to 117.1%, with the intra-day and inter-day relative standard deviations (RSDs) less than 13.4% and 16.5%, respectively.

Cyclodextrin polymers as highly effective adsorbents for removal and recovery of polychlorobiphenyl (PCB) contaminants in insulating oil.

A total of 179 countries (parties) ratified the Stockholm Convention on persistent organic pollutants (POPs) and agreed to destroy polychlorobiphenyls (PCBs) and develop a sound management plan by 2028. Currently, still 3 million tons of PCB-contaminated oil and equipment need to be managed under the Stockholm Convention. Thus, the development of a facile and environmentally benign method to treat large amounts of oil stockpiles contaminated with PCBs is a crucial subject. Herein, we report that cyclodextrin (CD) polymers, which are easily prepared by cross-linking the renewable cyclic oligosaccharide γ-cyclodextrin (γ-CD) with dibasic acid dichlorides, are a new selective and powerful adsorbent to remove PCB contaminants in oil. When PCB (100 ppm)-contaminated oil was passed through a column packed with the terephthaloyl-cross-linked γ-CD polymer (TP-γ-CD polymer) at 80-110 °C, the PCB contaminants were completely removed from the oil. Additionally, methyl esterification of the free carboxylic groups of the TP-γ-CD polymer enabled the complete recovery of the PCBs adsorbed on the polymer (with >99.9% recovery efficiency) by simply washing with acetone. The methyl-esterified TP-γ-CD polymer could be recycled at least 10 times for PCB adsorption without any loss in the adsorption capability. These results revealed that the γ-CD polymers can function as highly effective and powerful adsorbents for the removal and recovery of PCBs from PCB-contaminated oil and, thus, significantly contribute to the protection of the global environment.

Sensitive determination of polychlorinated biphenyls in environmental water samples by headspace solid-phase microextraction with bamboo charcoal@iron oxide black fibers prior to gas chromatography with tandem mass spectrometry.

We have investigated the feasibility of bamboo charcoal@iron oxide black for the headspace solid-phase microextraction of polychlorinated biphenyls in environmental water samples. Bamboo charcoal@iron oxide black was prepared and used as a solid-phase microextraction coating material, and gas chromatography with tandem mass spectrometry was used for detection. Several important factors affecting the extraction efficiency were systematically investigated and optimized. Under the optimum conditions, the experimental data exhibited wide linear range over the range 0.2-1000 ng/L and low limits of detection in the range of 4.7-22.2 pg/L. The novel coating was successfully used for the enrichment and determination of polychlorinated biphenyls in real environmental water samples. All these results indicated that bamboo charcoal@iron oxide black-based headspace solid-phase microextraction coupled to gas chromatography with tandem mass spectrometry was an excellent alternative for the sensitive analysis of polychlorinated biphenyls at ultratrace levels in the environment.

Fabrication of metal-organic framework MIL-88B films on stainless steel fibers for solid-phase microextraction of polychlorinated biphenyls.

Metal-organic frameworks (MOFs) have received considerable attention as novel sorbents for sample preparation due to their fascinating structures and functionalities such as large surface area, good thermal stability, and uniform structured nanoscale cavities. Here, we report the application of a thermal and solvent stable MOF MIL-88B with nanosized bipyramidal cages and large surface area for solid-phase microextraction (SPME) of polychlorinated biphenyls (PCBs). Novel MIL-88B coated fiber was fabricated via an in situ hydrothermal growth of MIL-88B film on etched stainless steel fiber. The MIL-88B coated fiber gave large enhancement factors (757-2243), low detection limits (0.45-1.32ngL(-1)), and good linearity (5-200ngL(-1)) for PCBs. The relative standard deviation (RSD) for six replicate extractions of PCBs at 100ngL(-1) on MIL-88B coated fiber ranged from 4.2% to 8.7%. The recoveries for spiked PCBs (10ngL(-1)) in water and soil samples were in the range of 79.7-103.2%. Besides, the MIL-88B coated fiber was stable enough for 150 extraction cycles without significant loss of extraction efficiency. The developed method was successfully applied to the determination of PCBs in water samples and soil samples.

Determination of polychlorinated biphenyls in fish: optimisation and validation of a method based on accelerated solvent extraction and gas chromatography-mass spectrometry.

A simple and robust method for the determination of 18 polychlorinated biphenyls (PCBs) in fish was developed and validated. A mixture of acetone/n-hexane (1:1, v/v) was selected for accelerated solvent extraction (ASE). After the digestion of fat, the clean-up was carried out using solid phase extraction silica cartridges. Samples were analysed by GC-MS in selected ion monitoring (SIM) using three fragment ions for each congener (one quantifier and two qualifiers). PCB 155 and PCB 198 were employed as internal standards. The lowest limit of detection was observed for PCB 28 (0.4ng/g lipid weight). The accuracy of the method was verified by means of the Certified Reference Material EDF-2525 and good results in terms of linearity (R(2)>0.994) and recoveries (80-110%) were also achieved. Precision was evaluated by spiking blank samples at 4, 8 and 12ng/g. Relative standard deviation values for repeatability and reproducibility were lower than 8% and 16%, respectively. The method was applied to the determination of PCBs in 80 samples belonging to four Mediterranean fish species. The proposed procedure is particularly effective because it provides good recoveries with lowered extraction time and solvent consumption; in fact, the total time of extraction is about 12min per sample and, for the clean-up step, a total solvent volume of 13ml is required.

Automated pipeline for classifying Aroclors in soil by gas chromatography/mass spectrometry using modulo compressed two-way data objects.

Seven polychlorinated biphenyls (PCBs) commercial mixtures, Aroclor 1016, 1221, 1232, 1242, 1248, 1254, and 1260, were analyzed by gas chromatography/mass spectrometry (GC/MS) combined with solid phase microextraction (SPME). Three pattern recognition methods: a fuzzy rule-building expert system (FuRES), partial least-squares discriminant analysis (PLS-DA), and a fuzzy optimal associative memory (FOAM) were used to build classification models. Modulo compression was introduced for data preprocessing to extract the characteristic features and compress the data size. Baseline correction and data normalization were also applied prior to data processing. Four GC/MS data set configurations were constructed and used to evaluate the classifiers and data pretreatments including two-way modulo compressed, two-way data, one-way total ion current and one-way total mass spectrum. The results indicate that modulo compression and baseline correction methods significantly improved the performance of the classifiers which resulted in improved classification rates for FuRES, PLS-DA, and FOAM classifiers. By using two-way modulo compressed data sets, the average classification rates with FuRES, PLS-DA, and FOAM were 100±0%, 94.6±0.7%, and 96.1±0.6% for 100 bootstrapped Latin partitions of the Aroclor standards. The classifiers were validated by application to Aroclor samples extracted from soil with no parametric changes except that the calibration set of standards and validation set of soil samples were individually mean centered. The classification rates for the GC/MS modulo 35 compressed data obtained from the Aroclor soil samples with FOAM, FuRES, and PLS-DA were 100%, 96.4%, and 78.6%, respectively. Therefore, a chemometric pipeline for SPME-GC/MS data coupled with chemometric analysis was devised as a fast authentication method for different Aroclors in soil.

Selective pressurized liquid extraction of pesticides, polychlorinated biphenyls and polybrominated diphenyl ethers in a whale earplug (earwax): a novel method for analyzing organic contaminants in lipid-rich matrices.

Lipid-rich matrices are often sinks for lipophilic contaminants, such as pesticides, polychlorinated biphenyls (PCBs), and polybrominated diphenyl ethers (PBDEs). Typically methods for contaminant extraction and cleanup for lipid-rich matrices require multiple cleanup steps; however, a selective pressurized liquid extraction (SPLE) technique requiring no additional cleanup has been developed for the simultaneous extraction and cleanup of whale earwax (cerumen; a lipid-rich matrix). Whale earwax accumulates in select whale species over their lifetime to form wax earplugs. Typically used as an aging technique in cetaceans, layers or laminae that comprise the earplug are thought to be associated with annual or semiannual migration and feeding patterns. Whale earplugs (earwax) represent a unique matrix capable of recording and archiving whales' lifetime contaminant profiles. This study reports the first analytical method developed for identifying and quantifying lipophilic persistent organic pollutants (POPs) in a whale earplug including organochlorine pesticides, polychlorinated biphenyls (PCBs), and polybrominated diphenyl ethers (PBDEs). The analytical method was developed using SPLE to extract contaminants from ∼0.25 to 0.5g aliquots of each lamina of sectioned earplug. The SPLE was optimized for cleanup adsorbents (basic alumina, silica gel, and Florisil(®)), adsorbent to sample ratio, and adsorbent order. In the optimized SPLE method, the earwax homogenate was placed within the extraction cell on top of basic alumina (5g), silica gel (15g), and Florisil(®) (10g) and the target analytes were extracted from the homogenate using 1:1 (v/v) dichloromethane:hexane. POPs were analyzed using gas chromatography-mass spectrometry with electron capture negative ionization and electron impact ionization. The average percent recoveries for the POPs were 91% (±6% relative standard deviation), while limits of detection and quantification ranged from 0.00057 to 0.96ngg(-1) and 0.0017 to 2.9ngg(-1), respectively. Pesticides, PCBs, and PBDEs, were measured in a single blue whale (Balaenoptera musculus) cerumen lamina at concentrations ranging from 0.11 to 150ng g(-1).

Validation of one-step cleanup and separation method of polychlorinated biphenyls, organochlorine pesticides, and polycyclic aromatic hydrocarbons from atmospheric gas- and particle-phase samples.

A one-step cleanup method is described for the determination of PAHs, PCBs and OCPs in air (gas and particulate phase) samples. Analytes were extracted from ambient air samples using soxhlet extraction with a solvent mixture of dichloromethane and petroleum ether (1:4) for 24h. They were concentrated, separated and fractionated on a florisil and alumina column. The amounts of florisil (1g or 2g) with/without alumina were tested in the cleanup column. The study systematically investigated the effects of solvent types, and the amounts of florisil and alumina, on the performance of the cleanup process. The first fraction was eluted with 25 mL hexane, and analyzed for PCBs. The second fraction was collected via 40 mL hexane-ethyl acetate (1:1) solvent mixture, and analyzed for OCPs and PAHs. The optimized method yielded average recoveries between 88% and 99% for PCBs; 56% and 118% for PAHs; and 51% and 128% for OCPs. Other validation parameters were also investigated, such as MDL, LOQ, linear range, sensitivity (r(2)). An oven-program optimization and adjustment of GC-MS were performed. For internal quality control, surrogate recoveries and field blanks values were calculated. External calibration curves were prepared for PAHs, and internal calibration curves were preferred for OCP and PCBs.