Characteristics of PM2.5 bounded carbonaceous aerosols, carbon dioxide and its stable carbon isotopes (δ13C) in rural households in northwest China: Effect of different fuel combustion.

In order to fully understand the carbon emission from different fuels in rural villages of China, especially in the typical atmospheric pollution areas. The characteristics of carbonaceous aerosols and carbon dioxide (CO2) with its stable carbon isotope (δ13C) were investigated in six households, which two households used coal, two households used wood as well as two households used biogas and liquefied petroleum gas (LPG), from two rural villages in Fenwei Plain from March to April 2021. It showed that the fine particulate matter (PM2.5) emitted from biogas and LPG couldn't be as lower as expected in this area. However, the clean fuels could relatively reduce the emissions of organic carbon (OC) and element carbon (EC) in PM2.5 compare to the solid fuels. The pyrolyzed carbon (OP) accounted more total carbon (TC) in coal than the other fuels use households, indicating that more water-soluble OC existed, and it still had the highest secondary organic carbon (SOC) than the other fuels. Meantime, the coal combustions in the two villages had the highest CO2 concentration of 527.6 ppm and 1120.6 ppm, respectively, while the clean fuels could effectively reduce it. The average δ13C values (-26.9‰) was much lighter than almost all the outdoor monitoring and similar to the δ13C values for coal combustion and vehicle emission, showing that they might be the main contributors of the regional atmospheric aerosol in this area. During the sandstorm, the indoor PM2.5 mass and CO2 were increasing obviously. The indoor cancer risk of PAHs for adults and children were greater than 1 × 10-6, exert a potential carcinogenic risk to human of solid fuels combustion in rural northern China. It is important to continue concern the solid fuel combustion and its health impact in rural areas.

China's "coal-to-gas" policy had large impact on PM1.0 distribution during 2016-2019.

Particulate matter with an aerodynamic diameter of less than 1 µm (PM1.0) can be extremely hazardous to human health, so it is imperative to accurately estimate the spatial and temporal distribution of PM1.0 and analyze the impact of related policies on it. In this study, a stacking generalization model was trained based on aerosol optical depth (AOD) data from satellite observations, combined with related data affecting aerosol concentration such as meteorological data and geographic data. Using this model, the PM1.0 concentration distribution in China during 2016-2019 was estimated, and verified by comparison with ground-based stations. The coefficient of determination (R2) of the model is 0.94, and the root-mean-square error (RMSE) is 8.49 µg/m3, mean absolute error (MAE) is 4.10 µg/m3, proving that the model has a very high performance. Based on the model, this study analyzed the PM1.0 concentration changes during the heating period (November and December) in the regions where the "coal-to-gas" policy was implemented in China, and found that the proposed "coal-to-gas" policy did reduce the PM1.0 concentration in the implemented regions. However, the lack of natural gas due to the unreasonable deployment of the policy in the early stage caused the increase of PM1.0 concentration. This study can provide a reference for the next step of urban air pollution policy development.

[Characteristics, Sources Apportionment, and Health Risks of PM2.5-bound PAHs and Their Derivatives Before and After Heating in Zibo City].

Atmospheric polycyclic aromatic hydrocarbons (PAHs) and their derivatives are a global problem that influences the environment and threatens human health. To investigate the characteristics, sources, and health risk assessment of PM2.5-bound PAHs and their derivatives, PM2.5 were collected at an urban site in Zibo from November 5 to December 26, 2020, and the concentrations of 16 conventional PAHs, nine NPAHs, and five OPAHs in PM2.5 were analyzed using gas chromatography-mass spectrometry. Source apportionment of PAHs and their derivatives was conducted using diagnostic ratios and a PMF model, and the health risks of PAHs and their derivatives to adult men and women were evaluated using the source-dependent incremental lifetime cancer risk (ILCR) model. The results showed that the average concentrations of ∑16pPAHs, ∑9NPAHs, and ∑5OPAHs in PM2.5 of Zibo City during the sampling period were (41.61 ± 13.40), (6.38 ± 5.70), and (53.20 ± 53.47) ng·m-3, respectively. The concentrations of the three PAHs increased significantly after heating, which were 1.31, 2.04, and 5.24 times larger than those before heating. During the sampling period, Chr, BaP, and BaA were the dominant components of pPAHs; 9N-Ant and 2N-Flt + 3N-Flt were the dominant components of NPAHs; and ATQ and BZO were the dominant components of OPAHs. Source apportionment results showed that motor vehicles were the main source of PAHs and their derivatives in PM2.5 before heating, whereas after heating, the main sources were the mixed source of coal and biomass combustion and secondary formation. The total BaP equivalent (TEQ) was 14.5 ng·m-3 during the sampling period, and the TEQ increased significantly after heating, which was approximately 1.2 times of that before heating. Assisted by the individual PAH source apportionment results, the ILCR of PM2.5-boundPAHs and NPAHs in Zibo City had a certain potential carcinogenic risk for adult males (1.06 × 10-5) and females (9.32 × 10-6). Among them, the health risks of PAHs from gasoline vehicles, diesel vehicles, and coal/biomass combustion were significantly higher than those from other emission sources.

Migration patterns and health risk assessment of polycyclic aromatic compounds in typical coal fire source.

The Wuda coal fire in Inner Mongolia, China, is a global catastrophic event. It emits a huge volume of organic pollutants, including polycyclic aromatic compounds (PACs), which are widely concerning due to their physiological toxicity and environmental persistence. However, there is no systematic study on the enrichment and migration patterns of PACs emitted from coal fires. Here, we compared samples from coal fire sponges and surrounding soil, and analyzed 47 PACs using GC × GC-TOFMS. Data analysis showed that the average content of 16 polycyclic aromatic hydrocarbons (16PAHs) in the coal fire sponge was 15400.65 ng/g, which is about 4.2 times higher than that in the surrounding soil. Meanwhile, 31 PACs were detected at levels far exceeding those of 16PAHs. The distribution pattern of PACs showed that coal fire sources are more likely to produce and store 16PAHs while surrounding soils are more likely to be enriched with PAH derivatives. The cancer risk assessment revealed a significant cancer risk in both the coal fires and the surrounding soil. The formation mechanism of oxygenated PAHs was also explored, and it was found that coal fires emit 16PAHs and alkylated PAHs, which oxidize to form oxygenated PAHs during migration to surrounding soils. The value of naphthaldehyde/alkylated naphthalene (< 2) can be referenced as characteristic markers of coal fire pollution. This provides a new perspective on the sources of PACs in the current environment.

Lentzea sokolovensis sp. nov., Lentzea kristufekii sp. nov. and Lentzea miocenica sp. nov., rare actinobacteria from Miocene lacustrine sediment of the Sokolov Coal Basin, Czech Republic.

The taxonomic position of three actinobacterial strains, BCCO 10_0061T, BCCO 10_0798T, and BCCO 10_0856T, recovered from bare soil in the Sokolov Coal Basin, Czech Republic, was established using a polyphasic approach. The multilocus sequence analysis based on 100 single-copy genes positioned BCCO 10_0061T in the same cluster as Lentzea waywayandensis, strain BCCO 10_0798T in the same cluster as Lentzea flaviverrucosa, Lentzea californiensis, Lentzea violacea, and Lentzea albidocapillata, and strain BCCO 10_0856T clustered together with Lentzea kentuckyensis and Lentzea alba. Morphological and chemotaxonomic characteristics of these strains support their assignment to the genus Lentzea. In all three strains, MK-9(H4) accounted for more than 80 % of the isoprenoid quinone. The diagnostic diamino acid in the cell-wall peptidoglycan was meso-diaminopimelic acid. The whole-cell sugars were rhamnose, ribose, mannose, glucose, and galactose. The major fatty acids (>10 %) were iso-C15 : 0, anteiso-C15 : 0, iso-C16 : 0, and C16 : 0. The polar lipids were diphosphatidylglycerol, methyl-phosphatidylethanolamine, phosphatidylethanolamine, hydroxy-phosphatidylethanolamine, phosphatidylglycerol, and phosphatidylinositol. The genomic DNA G+C content of strains (mol%) was 68.8 for BCCO 10_0061T, 69.2 for BCCO 10_0798T, and 68.5 for BCCO 10_0856T. The combination of digital DNA-DNA hybridization results, average nucleotide identity values and phenotypic characteristics of BCCO 10_0061T, BCCO 10_0798T, and BCCO 10_0856T distinguishes them from their closely related strains. Bioinformatic analysis of the genome sequences of the strains revealed several biosynthetic gene clusters (BGCs) with identities >50 % to already known clusters, including BGCs for geosmin, coelichelin, ε-poly-l-lysine, and erythromycin-like BGCs. Most of the identified BGCs showed low similarity to known BGCs (<50 %) suggesting their genetic potential for the biosynthesis of novel secondary metabolites. Based on the above results, each strain represents a novel species of the genus Lentzea, for which we propose the name Lentzea sokolovensis sp. nov. for BCCO 10_0061T (=DSM 116175T), Lentzea kristufekii sp. nov. for BCCO 10_0798T (=DSM 116176T), and Lentzea miocenica sp. nov. for BCCO 10_0856T (=DSM 116177T).

Selenium-modified activated coke: a high-capacity and facile designed Hg0 adsorbent for coal-fired flue gas.

The substantial amount of mercury emissions from coal-fired flue gas causes severe environmental contamination. With the Minamata Convention now officially in force, it is critical to strengthen mercury pollution control. Existing activated carbon injection technologies suffer from poor desulfurization performance and risk secondary-release risks. Therefore, considering the potential industrial application of adsorbents, we selected cost-effective and readily available activated coke (AC) as the carrier in this study. Four metal selenides-copper, iron, manganese, and tin-were loaded onto the AC to overcome the application problems of existing technologies. After 120 min of adsorption, the CuSe/AC exhibited the highest efficiency in removing Hg0, surpassing 80% according to the experimental findings. In addition, the optimal adsorption temperature window was 30-120 °C, the maximum adsorption rate was 2.9 × 10-2 mg·g-1·h-1, and the effectiveness of CuSe/AC in capturing Hg0 only dropped by 5.2% in the sulfur-containing atmosphere. The physicochemical characterization results indicated that the AC surface had a uniform loading of CuSe with a nanosheet structure resembling polygon and that the Cu-to-Se atomic ratio was close to 1:1. Finally, two possible Hg0 reaction pathways on CuSe/AC were proposed. Moreover, it was elucidated that the highly selective binding of Hg0 with ligand-unsaturated Se- was the key factor in achieving high adsorption efficiency and sulfur resistance in the selenium-functionalized AC adsorbent. This finding offers substantial theoretical support for the industrial application of this adsorbent.

Migration and distribution characteristics of typical organic pollutants in condensable particulate matter of coal-fired flue gas and by-products of wet flue gas desulfurization system.

The wet flue gas desulfurization (WFGD) system of coal-fired power plants shows a good removal effect on condensable particulate matter (CPM), reducing the dust removal pressure for the downstream flue gas purification devices. In this work, the removal effect of a WFGD system on CPM and its organic pollutants from a coal-fired power plant was studied. By analyzing the organic components of the by-products emitted from the desulfurization tower, the migration characteristics of organic pollutants in gas, liquid, and solid phases, as well as the impact of desulfurization towers on organic pollutants in CPM, were discussed. Results show that more CPM in the flue gas was generated by coal-fired units at ultra-low load, and the WFGD system had a removal efficiency nearly 8% higher than that at full load. The WFGD system had significant removal effect on two typical esters, especially phthalate esters (PAEs), with the highest removal efficiency of 49.56%. In addition, the WFGD system was better at removing these two esters when the unit was operating at full load. However, it had a negative effect on n-alkanes, which increased the concentration of n-alkanes by 8.91 to 19.72%. Furthermore, it is concluded that the concentration distribution of the same type of organic pollutants in desulfurization wastewater was similar to that in desulfurization slurry, but quite different from that in coal-fired flue gas. The exchange of three organic pollutants between flue gas and desulfurization slurry was not significant, while the concentration distribution of organic matters in gypsum was affected by coal-fired flue gas.

Study on the mechanism of action of methane production by co-fermentation of sludge and lignite.

To improve the methanogenic efficiency of lignite anaerobic fermentation and explore innovative approaches to sludge utilization, a co-fermentation technique involving lignite and sludge was employed for converting biomass into biomethane. Volatile suspended solids were introduced as a native enrichment of the sludge and mixed with lignite for fermentation. The synergistic fermentation mechanism between sludge and lignite for biomethane production was analyzed through biochemical methane potential experiments, measurement of various parameters pre- and post-fermentation, observation of bacterial population changes during the peak of reaction, carbon migration assessment, and evaluation of rheological characteristics. The results showed that the addition of sludge in the anaerobic fermentation process improved the microorganisms' ability to degrade lignite and bolstered biomethane production. Notably, the maximum methane production recorded was 215.52 mL/g-volatile suspended solids, achieved at a sludge to coal ratio of 3:1, with a synergistic growth rate of 25.37%. Furthermore, the removal rates of total suspended solids, and total chemical oxygen demand exhibited an upward trend with an increasing percentage of sludge in the mixture. The relative abundance and activity of the methanogens population were found to increase with an appropriate ratio of sludge to lignite. This observation confirmed the migration of carbon between the solid-liquid-gas phases, promoting enhanced system affinity. Additionally, the changes in solid-liquid phase parameters before and after the reaction indicated that the addition of sludge improved the system's degradation capacity. The results of the study hold significant implications in realizing the resource utilization of sludge and lignite while contributing to environmental protection endeavors.

Major influencing factors identification and probabilistic health risk assessment of soil potentially toxic elements pollution in coal and metal mines across China: A systematic review.

Deposition of potentially toxic elements (PTEs) in soils due to different types of mining activities has been an increasingly important concern worldwide. Quantitative differences of soil PTEs contamination and related health risk among typical mines remain unclear. Herein, data from 110 coal mines and 168 metal mines across China were analyzed based on 265 published literatures to evaluate pollution characteristics, spatial distribution, and probabilistic health risks of soil PTEs. The results showed that PTE levels in soil from both mine types significantly exceeded background values. The geoaccumulation index (Igeo) revealed metal-mine soil pollution levels exceeded those of coal mines, with average Igeo values for Cd, Hg, As, Pb, Cu, and Zn being 3.02-15.60 times higher. Spearman correlation and redundancy analysis identified natural and anthropogenic factors affecting soil PTE contamination in both mine types. Mining activities posed a significant carcinogenic risk, with metal-mine soils showing a total carcinogenic risk an order of magnitude higher than in coal-mine soils. This study provides policymakers a quantitative foundation for developing differentiated strategies for sustainable remediation and risk-based management of PTEs in typical mining soils.

Subsidizing Grid-Based Electrolytic Hydrogen Will Increase Greenhouse Gas Emissions in Coal Dominated Power Systems.

Clean hydrogen has the potential to serve as an energy carrier and feedstock in decarbonizing energy systems, especially in "hard-to-abate" sectors. Although many countries have implemented policies to promote electrolytic hydrogen development, the impact of these measures on costs of production and greenhouse gas emissions remains unclear. Our study conducts an integrated analysis of provincial levelized costs and life cycle greenhouse gas emissions for all hydrogen production types in China. We find that subsidies are critical to accelerate low carbon electrolytic hydrogen development. Subsidies on renewable-based hydrogen provide cost-effective carbon dioxide equivalent (CO2e) emission reductions. However, subsidies on grid-based hydrogen increase CO2e emissions even compared with coal-based hydrogen because grid electricity in China still relies heavily on coal power and likely will beyond 2030. In fact, CO2e emissions from grid-based hydrogen may increase further if China continues to approve new coal power plants. The levelized costs of renewable energy-based electrolytic hydrogen vary among provinces. Transporting renewable-based hydrogen through pipelines from low- to high-cost production regions reduces the national average levelized cost of renewables-based hydrogen but may increase the risk of hydrogen leakage and the resulting indirect warming effects. Our findings emphasize that policy and economic support for nonfossil electrolytic hydrogen is critical to avoid an increase in CO2e emissions as hydrogen use rises during a clean energy transition.

Potential toxic components in size-resolved particles and gas from residential combustion: Emission factor and health risk.

Particulate matter (PM) from residential combustion is an existential threat to human health. Emission factors (EFs) of multiple potential toxic components (PTCs) in size-resolved PM and gas from eight residential fuel combustion were measured, and size distribution, gas/particle partitioning and health risks of the PTCs were investigated. Average EFs from clean coal and anthracite coal were PTEs (sum of EFs of 11 Potential Toxic Elements, 6.62 mg/kg fuels) > PAHs (sum of 22 Polycyclic Aromatic Hydrocarbons, 1.12 mg/kg) > OPAHs (sum of 5 Oxygenated Polycyclic Aromatic Hydrocarbons, 0.45 mg/kg) > PAEs (sum of 6 Phthalate Esters, 0.11 mg/kg) > NPAHs (sum of 14 Nitropolycyclic Aromatic Hydrocarbons, 16.84 µg/kg) > OPEs (sum of 7 Organophosphate Esters, 7.57 µg/kg) > PCBs (sum of 6 Polychorinated Biphenyls, 0.07 µg/kg), which were 2-3 and 1-2 orders of magnitude lower than the EFs of PTCs (except PTEs) from bituminous coal and biomass. Most PAHs, OPAHs and NPAHs, which may mainly originate from chemical reactions, showed similar size distributions and averagely 85 % concentrated in PM1. PTEs, PAEs, OPEs and PCBs generated from the release from raw fuels may have a higher proportion, so their size distributions were more complex and varied with combustion temperature, volatility of compounds, binding mode of the raw fuels, and so on. In addition, clean coal and high-quality anthracite coal could reduce the health risks from the potential organic toxic components, but also reveal the stumbling block of PTEs in risk control.

The biotic effects of lignite on humic acid components conversion during chicken manure composting.

Targeted regulation of composting to convert organic matter into humic acid (HA) holds significant importance in compost quality. Owing to its low carbon content, chicken manure compost often requires carbon supplements to promote the humification progress. The addition of lignite can increase HA content through biotic pathways, however, its structure was not explored. The Parallel factor analysis revealed that lignite can significantly increase the complexity of highly humified components. The lignite addition improved phenol oxidase activity, particularly laccase, during the thermophilic and cooling phases. The abundance and transformation functions of core bacteria also indicated that lignite addition can influence the activity of microbial transformation of HA components. The structural equation model further confirmed that lignite addition had a direct and indirect impact on enhancing the complexity of HA components through core bacteria and phenol oxidase. Therefore, lignite addition can improve HA structure complexity during composting through biotic pathways.

Toward a comprehensive life-cycle carcinogenic impact assessment: A statistical regression approach based on cancer burden.

The current approach to life cycle carcinogenic impact assessment (LCCA) is hindered by its static and linear characteristics. This situation prevents the accurate prediction of the incidence, associated damage, and potential economic burden of cancer. This study explores a highly comprehensive pathway for LCCA assessment. It uses the impacts of Tracheal, bronchus, and lung (TBL) predicted by the LCCA of China's coal power industry through a screened statistical regression model as the research target. The latest global burden of disease estimates is utilized to quantify the health damage from TBL incidence, whereas an approach combining the actual cost of health and human capital is applied to further assess the economic burden of TBL. Findings indicate that the traditional and static LCCA method, which relies on animal toxicity data, can lead to underestimations in actual LCCA. The interaction among spatiotemporal meteorological factors, epidemiological cancer disease burden, and socioeconomic behaviors allows exhibits nonlinearity due to the changes in the combined toxicity of mixed key substances. Following the active implementation of ultralow emission and energy-saving transformations in China's coal power industry, the national percentage of TBL cancer incidence caused by pollutants from the coal power industry decreased from 25.2 % in 2004 to 11.5 % in 2020. Results indicate that the established dynamic LCCA model based on temporal and spatial climate, socioeconomic, and epidemiological cancer data can be feasibly employed for the accurate impact evaluation and mitigation of carcinogens in practical applications.

Life-Course Health Risk Assessment of PM2.5 Elements in China: Exposure Disparities by Species, Source, Age, Gender, and Location.

Key stages in people's lives have particular relevance for their health; the life-course approach stresses the importance of these stages. Here, we applied a life-course approach to analyze the health risks associated with PM2.5-bound elements, which were measured at three sites with varying environmental conditions in eastern China. Road traffic was found to be the primary source of PM2.5-bound elements at all three locations, but coal combustion was identified as the most important factor to induce both cancer risk (CR) and noncancer risk (NCR) across all age groups due to the higher toxicity of elements such as As and Pb associated with coal. Nearly half of NCR and over 90% of CR occurred in childhood (1-6 years) and adulthood (>18 years), respectively, and females have slightly higher NCR and lower CR than males. Rural population is found to be subject to the highest health risks. Synthesizing previous relevant studies and nationwide PM2.5 concentration measurements, we reveal ubiquitous and large urban-rural environmental exposure disparities over China.

Insights into PM2.5 pollution of four small and medium-sized cities in Chinese representative regions: Chemical compositions, sources and health risks.

Fine particles (PM2.5) pollution is still a severe issue in some cities in China, where the chemical characteristics of PM2.5 remain unclear due to limited studies there. Herein, we focused on PM2.5 pollution in small and medium-sized cities in key urban agglomerations and conducted a comprehensive study on the PM2.5 chemical characteristics, sources, and health risks. In the autumn and winter of 2019-2020, PM2.5 samples were collected simultaneously in four small and medium-sized cities in four key regions: Dingzhou (Beijing-Tianjin-Hebei region), Weinan (Fenwei Plain region), Fukang (Northern Slope of the Tianshan Mountain region), and Bozhou (Yangtze River Delta region). The results showed that secondary inorganic ions (43.1 %-67.0 %) and organic matter (OM, 8.6 %-36.4 %) were the main components of PM2.5 in all the cities. Specifically, Fukang with the most severe PM2.5 pollution had the highest proportion of SO42- (31.2 %), while the dominant components in other cities were NO3- and OM. The Multilinear Engine 2 (ME2) analysis identified five sources of PM2.5 in these cities. Coal combustion contributed most to PM2.5 in Fukang, but secondary sources in other cities. Combined with chemical characteristics and ME2 analysis, it was preliminarily determined that the primary emission of coal combustion had an important contribution to high SO42- in Fukang. Potential source contribution function (PSCF) analysis results showed that regional transport played an important role in PM2.5 in Dingzhou, Weinan and Bozhou, while PM2.5 in Fukang was mainly affected by short-range transport from surrounding areas. Finally, the health risk assessment indicated Mn was the dominant contributor to the total non-carcinogenic risks and Cr had higher carcinogenic risks in all cities. The findings provide a scientific basis for formulating more effective abatement strategies for PM2.5 pollution.

Indoor PM from residential coal combustion: Levels, chemical composition, and toxicity.

Indoor air quality is crucial for human health due to the significant time people spend at home, and it is mainly affected by internal sources such as solid fuel combustion for heating. This study investigated the indoor air quality and health implications associated with residential coal burning covering gaseous pollutants (CO, CO2 and total volatile organic compounds), particulate matter, and toxicity. The PM10 chemical composition was obtained by ICP-MS/OES (elements), ion chromatography (water-soluble ions) and thermal-optical analysis (organic and elemental carbon). During coal combustion, PM10 levels were higher (up to 8.8 times) than background levels and the indoor-to-outdoor ratios were, on average, greater than unity, confirming the existence of a significant indoor source. The chemical characterisation of PM10 revealed increased concentrations of organic carbon and elemental carbon during coal combustion as well as arsenic, cadmium and lead. Carcinogenic risks associated with exposure to arsenic exceeded safety thresholds. Indoor air quality fluctuated during the study, with varying toxicity levels assessed using the Aliivibrio fischeri bioluminescence inhibition assay. These findings underscore the importance of mitigating indoor air pollution associated with coal burning and highlight the potential health risks from long-term exposure. Effective interventions are needed to improve indoor air quality and reduce health risks in coal-burning households.

Fine particle trace elements at a mountain site in southern China: Source identification, transport, and health risks.

Trace elements in atmospheric particulate matter play a significant role in air quality, human health, and biogeochemical cycles. In this study, the trace elements (Ca, Al, K, Fe, Na, Mg, Zn, Pb, Mn, Ti, Cu, Cr, Sr, Ni) in PM2.5 samples collected at the summit of Mt. Lushan were analyzed to quantify their abundance, source, transport, and health risks. During the whole sampling period, the major trace elements was Ca, Al, and K. While the trace metals with the lowest concentrations were Sr, Ni, Rb, and Cd. The trace elements were influenced by air mass transport routes, exhibiting an increasing trend of crustal elements in the northwesterly airmass and anthropogenic elements (Zn, Mn, Cu, and Ni) in the easterly air masses. Construction dust, coal + biomass burning, vehicle emission, urban nitrate-rich + urban waste incineration emissions, and soil dust + industry emissions were common sources of PM2.5 on Mt. Lushan. Different air mass transport routes had various source contribution patterns. These results indicate that trace elements at Mt. Lushan are influenced by regional anthropogenic emissions and monsoon-dominated trace element transport. The total resulting cancer risk value that these elements posed were below the acceptable risk value of 1 × 10-6, while the non-carcinogenic risk value (1.72) was higher than the safety level, suggesting that non-carcinogenic effects due to these trace elements inhalation were likely to occur. Vehicle emission and coal + biomass burning were the common dominant sources of non-cancer risks posed by trace elements at Mt. Lushan.

[Comparison and analysis research on occupational exposure limits of coal dust between China and foreign countries].

Objective: To study and compare the occupational exposure limits (OELs) of coal dust between China and foreign countries, understand the OEL of coal dust in China, and provide data and basis for revising the OEL of coal dust in China. Methods: In August 2023, by searching the official websites of limits setting institutions in relevant countries and regions at home and abroad, collecting and sorting out the OELs of coal dust issued by 10 limit setting institutions in 6 countries and the background information of the formulation, and conducting specific analysis on the classification, limit level and formulation principles of coal dust OEL in each country/institution. Results: In China and Japan, the total dust and respirable dust of coal dust OEL were established respectively, while in other countries, only the time-weighted average concentration (TWA) of respirable coal dust exposure was established. The TWA prescribed by China's Notional Health Commission, the United States Occupational Safety and Health Administration (OSHA) , the United States Mining Safety and Health Administration (MSHA) and the Australian Safety Work Bureau when the SiO(2) content was less than 5% were 5, 2.4, 2 and 3 mg/m(3) respectively. China GBZ 2.1-2019 sets the limit of 2.5 mg/m(3) for respirable coal dust with SiO(2) content less than 10%. The TWA set by the American Conference of Government Industrial Hygienists (ACGIH) and the South African Department of Mines and Energy (DME) for anthracite coal were 0.4 and 0.8 mg/m(3), respectively, and bituminous coal or lignite were 0.9 and 1.8 mg/m(3), respectively. The respirable coal dust TWA set by the National Institute for Occupational Safety and Health (NIOSH) in the United States was 1 mg/m(3), and the TWA set by the New Zealand Work Safety Authority was 3 mg/m(3). Conclusion: At present, the OEL of coal dust in China is at a relatively loose level, and it is suggested to further explore the possibility of revising coal dust OEL.

Particulate polycyclic aromatic hydrocarbons in rural households burning solid fuels in Xuanwei County, Southwest China: occurrence, size distribution, and health risks.

The study is about the size distribution and health risks of polycyclic aromatic hydrocarbons (PAHs) in indoor environment of Xuanwei, Southwest China particle samples were collected by Anderson 8-stage impactor which was used to gather particle samples to nine size ranges. Size-segregated samples were collected in indoor from a rural village in Xuanwei during the non-heating and heating seasons. The results showed that the total concentrations of the indoor particulate matter (PM) were 757 ± 60 and 990 ± 78 µg/m3 in non-heating and heating seasons, respectively. The total concentration of indoor PAHs reached to 8.42 ± 0.53 µg/m3 in the heating season, which was considerably greater than the concentration in the non-heating season (2.85 ± 1.72 µg/m3). The size distribution of PAHs showed that PAHs were mainly enriched in PMs with the diameter <1.1 µm. The diagnostic ratios (DR) and principal component analysis (PCA) showed that coal and wood for residential heating and cooking were the main sources of indoor PAHs. The results of the health risk showed that the total deposition concentration (DC) in the alveolar region (AR) was 0.25 and 0.68 µg/m3 in the non-heating and heating seasons respectively. Throughout the entire sampling periods, the lifetime cancer risk (R) based on DC of children and adults varied between 3.53 ×10-5 to 1.79 ×10-4. During the heating season, the potential cancer risk of PAHs in adults was significant, exceeding 10-4, with a rate of 96%.

Spatial-temporal distribution and source analysis of atmospheric particulate-bound cadmium from 1998 to 2021 in China.

Cadmium (Cd) is one of the most serious atmospheric heavy metal pollutants in China. PM2.5, PM10, and total suspended particle (TSP) are all important media for population Cd exposure. However, no studies so far have systematically explored the spatial and temporal distribution of atmospheric Cd bound to all these media in China, and the specific industrial sectors that contribute to the airborne Cd level are still unclear at present. In this study, we constructed the spatial and temporal distribution of PM (PM2.5, PM10, and TSP) binding Cd concentrations in China. Quantitative source apportionment of atmospheric Cd was carried out by analyzing the association of 23 industrial or energy-consuming sectors with Cd concentrations. Our results showed PM2.5, PM10, and TSP binding Cd concentrations decreased by 5.8%, 5.9%, and 6.1% per year at the national level, respectively. High PM-Cd concentrations were concentrated and distributed mainly in central and northwestern China. In addition, the medians of atmospheric PM2.5, PM10, and TSP binding Cd concentrations at the national level were 0.0026 µg/m3, 0.0036 µg/m3, and 0.0042 µg/m3, respectively. The main sources of PM-Cd include nonferrous metal smelting (Zn, Pb, Al) (47%), glass production (13%), pesticide production (12%), cement production (10%), and coal consumption (9%). This study analyzes comprehensively the atmospheric PM-bound Cd pollution, identifies the major industrial sectors that affect atmospheric Cd concentrations at the macroscale for the first time, and provides a basis for further reduction in the atmospheric Cd pollution.