Evaluation of the automated micro-solid phase extraction clean-up system for the analysis of pesticide residues in cereals by gas chromatography-Orbitrap mass spectrometry.

Food analysis is a tremendously broad field that is constantly evolving. New methods have emerged to increase productivity, such as modern miniaturized and robotic analytical techniques. In this paper, a micro-solid-phase extraction system (µ-SPE) for clean-up was combined with a robotic autosampler to yield ready-to-analyze extracts. The system was evaluated for its applicability in routine laboratories. The new, automated, high-throughput µ-SPE clean-up method was applied to acetonitrile extracts and was developed for the analysis of pesticide residues in cereals by gas chromatography-Orbitrap mass spectrometry (GC-Orbitrap-MS). The µ-SPE clean-up efficiency was demonstrated in the removal of matrix-interfering components and in the recovery of pesticides. The sorbent bed mixture consisted of magnesium sulfate, primary-secondary amine, C18, and CarbonX, and effectively retained matrix components without loss of target analytes. Analysis of five types of cereals (barley, oat, rice, rye, and wheat) by GC-Orbitrap-MS showed that the method removed more than 70% of matrix components. The clean-up method was validated for 170 pesticides in rye, 159 pesticides in wheat, 142 pesticides in barley, 130 pesticides in oat, and 127 pesticides in rice. Spike recovery values were 70-120% for all pesticides and the repeatability, calculated as the relative standard deviation, was less than 20%. The limits of quantitation achieved were 0.005 mg kg-1 for almost all analytes, ensuring compliance with the maximum residue limits.

A Tailored High-Efficiency Sample Pretreatment Method for Simultaneous Quantification of 10 Classes of Known Endogenous Phytohormones.

One of the hottest topics in plant hormone biology is the crosstalk mechanisms, whereby multiple classes of phytohormones interplay with each other through signaling networks. To better understand the roles of hormonal crosstalks in their complex regulatory networks, it is of high significance to investigate the spatial and temporal distributions of multiple -phytohormones simultaneously from one plant tissue sample. In this study, we develop a high-sensitivity and high-throughput method for the simultaneous quantitative analysis of 44 phytohormone compounds, covering currently known 10 major classes of phytohormones (strigolactones, brassinosteroids, gibberellins, auxin, abscisic acid, jasmonic acid, salicylic acid, cytokinins, ethylene, and polypeptide hormones [e.g., phytosulfokine]) from only 100 mg of plant sample. These compounds were grouped and purified separately with a tailored solid-phase extraction procedure based on their physicochemical properties and then analyzed by LC-MS/MS. The recoveries of our method ranged from 49.6% to 99.9% and the matrix effects from 61.8% to 102.5%, indicating that the overall sample pretreatment design resulted in good purification. The limits of quantitation (LOQs) of our method ranged from 0.06 to 1.29 pg/100 mg fresh weight and its precision was less than 13.4%, indicating high sensitivity and good reproducibility of the method. Tests of our method in different plant matrices demonstrated its wide applicability. Collectively, these advantages will make our method helpful in clarifying the crosstalk networks of phytohormones.

Rapid Monitoring of Organochlorine Pesticide Residues in Various Fruit Juices and Water Samples Using Fabric Phase Sorptive Extraction and Gas Chromatography-Mass Spectrometry.

Fabric phase sorptive extraction, an innovative integration of solid phase extraction and solid phase microextraction principles, has been combined with gas chromatography-mass spectrometry for the rapid extraction and determination of nineteen organochlorine pesticides in various fruit juices and water samples. FPSE consolidates the advanced features of sol-gel derived extraction sorbents with the rich surface chemistry of cellulose fabric substrate, which could extract the target analytes directly from the complex sample matrices, substantially simplifying the sample preparation operation. Important FPSE parameters, including sorbent chemistry, extraction time, stirring speed, type and volume of back-extraction solvent, and back-extraction time have been optimized. Calibration curves were obtained in a concentration range of 0.1⁻500 ng/mL. Under optimum conditions, limits of detection were obtained in a range of 0.007⁻0.032 ng/mL with satisfactory precision (RSD < 6%). The relative recoveries obtained by spiking organochlorine pesticides in water and selected juice samples were in the range of 91.56⁻99.83%. The sorbent sol-gel poly(ethylene glycol)-poly(propylene glycol)-poly(ethylene glycol) was applied for the extraction and preconcentration of organochlorine pesticides in aqueous and fruit juice samples prior to analysis with gas chromatography-mass spectrometry. The results demonstrated that the present method is simple, rapid, and precise for the determination of organochlorine pesticides in aqueous samples.

Evaluation of highly efficient on-line yarn-in-tube solid phase extraction method for ultra-trace determination of chlorophenols in honey samples.

In this study a novel "yarn-in-tube" configuration was introduced by packing cotton yarn inside stainless steel cartridge named packed yarn-in-tube solid phase extraction (yarn-IT-SPE) followed by high performance liquid chromatography. For the first time, cotton yarns were coated with a new polypyrrole@copper-chromium-iron ternary layered double hydroxide nanocomposite (Yarn@PPy@Cu-Cr-Fe LDH). The yarn@PPy@Cu-Cr-Fe LDH sorbent exhibited flexible substrate, high porosity, a three-dimensional, high sorbent loading, long lifetime, good mechanical stability, high anion-exchange capacity and large specific surface area as a result it is a good choice for the separation and preconcentration of acidic cholorophenols in honey samples. Several important factors affecting extraction efficiency such as extraction and desorption times, pH of solution and flow rates of the sample solution and eluent were investigated and optimized. Under the optimal conditions, the limits of detection were in the range of 0.05-0.07 µg L-1. This method showed good linearity for chlorophenols in the range of 0.10-500 µg L-1, with coefficients of determination better than 0.9989. The inter- and intra-assay precisions (RSD%, n = 5) were in the range of 3.2-4.9% and 2.1-3.6% at three concentration levels of 2, 10 and 20 µg L-1, respectively. The validated method was successfully applied for analysis of 4-chloro-, 2,4-dichloro-, and 2,4,6-trichloro phenols in honey samples.

Comparison of methods for determination of total oil sands-derived naphthenic acids in water samples.

There are several established methods for the determination of naphthenic acids (NAs) in waters associated with oil sands mining operations. Due to their highly complex nature, measured concentration and composition of NAs vary depending on the method used. This study compared different common sample preparation techniques, analytical instrument methods, and analytical standards to measure NAs in groundwater and process water samples collected from an active oil sands operation. In general, the high- and ultrahigh-resolution methods, namely high performance liquid chromatography time-of-flight mass spectrometry (UPLC-TOF-MS) and Orbitrap mass spectrometry (Orbitrap-MS), were within an order of magnitude of the Fourier transform infrared spectroscopy (FTIR) methods. The gas chromatography mass spectrometry (GC-MS) methods consistently had the highest NA concentrations and greatest standard error. Total NAs concentration was not statistically different between sample preparation of solid phase extraction and liquid-liquid extraction. Calibration standards influenced quantitation results. This work provided a comprehensive understanding of the inherent differences in the various techniques available to measure NAs and hence the potential differences in measured amounts of NAs in samples. Results from this study will contribute to the analytical method standardization for NA analysis in oil sands related water samples.

Validation of QuEChERS based method for determination of fenitrothion residues in tomatoes by gas chromatography-flame photometric detector: Decline pattern and risk assessment.

A simple and rapid gas chromatography with flame photometric detector (GC-FPD) determination method was developed to detect residue levels and investigate the dissipation pattern and safe use of fenitrothion in tomatoes. A modified quick, easy, cheap, effective, rugged, and safe (QuEChERS) using an ethyl acetate-based extraction, followed by a dispersive solid-phase extraction (d-SPE) with primary-secondary amine (PSA) and graphite carbon black (GCB) for clean up, was applied prior to GC-FPD analysis. The method showed satisfactory linearity, recovery and precision. The limits of detection (LOD) and quantification (LOQ) were 0.005 and 0.01mg/kg, respectively. The residue levels of fenitrothion were best described by first order kinetics with a half-life of 2.2days in tomatoes. The potential health risks posed by fenitrothion were not significant, based on supervised residue trial data. The current findings could provide guidance for safe and reasonable use of fenitrothion in tomatoes and prevent health problems to consumers.

Quantitative analysis of maytansinoid (DM1) in human serum by on-line solid phase extraction coupled with liquid chromatography tandem mass spectrometry - Method validation and its application to clinical samples.

A sensitive and specific method was developed and validated for the quantitation of maytansinoid (DM1) in human serum using on-line solid phase extraction (SPE)-liquid chromatography-tandem mass spectrometry (LC-MS/MS). Because DM1 contains a free thiol moiety, likely to readily dimerize or react with other thiol-containing molecules in serum, samples were pre-treated with a reducing agent [tris (2-carboxyethyl) phosphine] (TCEP) and further blocked with N-ethylmaleimide (NEM). The resulting samples were diluted with acetonitrile prior to the on-line solid phase extraction (SPE) on a C18 cartridge. A C18 (150×4.6mm ID 3µm particle size) column was used for chromatographic separation with a 10.0min HPLC gradient and DM1-NEM was detected in the selected reaction monitoring mode of a triple quadrupole mass spectrometer. DM1 concentrations were back-calculated from DM1-NEM amount found in the human serum samples. The quantitation range of the method was 0.200-200ng/mL when using 0.25mL serum. Within-run day precisions (n=6) were 0.9-4.4% and between-run day (3 days runs; n=18) precisions 2.5-5.6%. Method biases were between 3.5-14.5% across the whole calibration range. DM1-NEM exhibited sufficiently stability under all relevant analytical conditions and no DM1 losses from the ADC were observed. Finally, the assay was used for DM1 determination in human serum concentration after the intravenous administration of an investigational antibody drug conjugate (ADC) containing DM1 as payload.

Validated Method for the Quantification of Buprenorphine in Postmortem Blood Using Solid-Phase Extraction and Two-Dimensional Gas Chromatography-Mass Spectrometry.

A highly sensitive and fully validated method was developed for the quantification of buprenorphine in postmortem blood. After a two-step protein precipitation process using acetonitrile, buprenorphine was purified using mixed-mode (C8/cation exchange) solid-phase extraction cartridges. Endogenous water-soluble compounds and lipids were removed from the cartridges before the samples were eluted, concentrated and derivatized using N-methyl-N-trimethylsilyltrifluoroacetamide. The samples were analyzed using two-dimensional gas chromatography-mass spectrometry (2D GC-MS) in selective ion-monitoring mode. A low polarity Rxi(®)-5MS (30 m × 0.25 mm I.D. × 0.25 µm) was used as the primary column and the secondary column was a mid-polarity Rxi(®) -17Sil MS (15 m × 0.32 mm I.D. × 0.25 µm). The assay was linear from 1.0 to 50.0 ng/mL (r(2) > 0.99; n = 6). Intraday (n = 6) and interday (n = 9) imprecisions (percentage relative standard deviation, % RSD) were <5% and the average recovery was 60%. The limit of detection (LOD) of the method was 0.5 ng/mL and limit of quantification was 1.0 ng/mL. 2D GC-MS improved the LOD of buprenorphine by 20-fold compared with analysis on a conventional GC-MS. The method was highly selective with no interference from endogenous compounds or from 62 commonly encountered drugs. To prove method applicability to forensic postmortem cases, 14 authentic postmortem blood samples were analyzed.

Assessment of two extraction methods to determine pesticides in soils, sediments and sludges. Application to the Túria River Basin.

Pressurized liquid extraction (PLE) and Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) extraction methods were optimized for the simultaneous determination of 50 pesticides in sediment, soils and sewage sludge. For QuEChERS development, several buffers and dispersive solid-phase extraction clean-up (dSPE) sorbents were tested. In the PLE method, several parameters affecting the extraction efficiency, such as organic solvent, amount of sample, cell size, temperature, pressure, static time, number of cycles and % of flush, as well as sorbent used for the on-line clean up, were also evaluated. PLE and QuEChERS were assessed and compared in obtained recoveries (33-89% versus 25-120%), number of pesticides for which recoveries are in the range of 80-100% (up to 13 versus up to 35) and cost of the approach. QuEChERS procedure was faster, cheaper and easier to perform. Recoveries were around 80% (at 50ngg(-1) d.w.) and the matrix effect was less than -20% using matrix-matched standard calibration curve for most of the analytes. The limits of quantification were between 0.1 and 10ngg(-1) (d.w.) except for alachlor and acetochlor. Repeatability and reproducibility were lower than 28% (%RSD, n=5). Soil, sediment and sludge samples, taken from the Túria River Basin, were analyzed by QuEChERS to determine pesticides. Chlorpyrifos (up to 65.3ngg(-1) d.w.) was the most frequent and at higher concentrations. Thiabendazole, imazalil, diazinon, pyriproxyfen, hexythiazox, carbofuran, isoproturon, terbuthylazine and terbumeton were also found in some samples.

Extraction efficiency of hydrophilic and lipophilic antioxidants from lyophilized foods using pressurized liquid extraction and manual extraction.

The efficient extraction of antioxidants from food samples is necessary in order to accurately measure their antioxidant capacities. α-Tocopherol and gallic acid were spiked into samples of 5 lyophilized and pulverized vegetables and fruits (onion, cabbage, Satsuma mandarin orange, pumpkin, and spinach). The lipophilic and hydrophilic antioxidants in the samples were sequentially extracted with a mixed solvent of n-hexane and dichloromethane, and then with acetic acid-acidified aqueous methanol. Duplicate samples were extracted: one set was extracted using an automated pressurized liquid extraction apparatus, and the other set was extracted manually. Spiked α-tocopherol and gallic acid were recovered almost quantitatively in the extracted lipophilic and hydrophilic fractions, respectively, especially when pressurized liquid extraction was used. The expected increase in lipophilic oxygen radical absorbance capacity (L-ORAC) due to spiking with α-tocopherol, and the expected increase in 2,2-diphenyl-1-picrylhydrazyl radical scavenging activities and total polyphenol content due to spiking with gallic acid, were all recovered in high yield. Relatively low recoveries, as reflected in the hydrophilic ORAC (H-ORAC) value, were obtained following spiking with gallic acid, suggesting an interaction between gallic acid and endogenous antioxidants. The H-ORAC values of gallic acid-spiked samples were almost the same as those of postadded (spiked) samples. These results clearly indicate that lipophilic and hydrophilic antioxidants are effectively extracted from lyophilized food, especially when pressurized liquid extraction is used.

An improved and validated sample cleanup method for analysis of ethyl carbamate in Chinese liquor.

Ethyl carbamate (EC) is a potential human carcinogen widely existing in fermented foods and alcoholic beverages. The solid-phase extraction (SPE) coupled to gas chromatography mass spectrometry is a widely-used method to determine EC levels, but the accuracy varies with sample matrix and the effects of operation parameters are rarely examined. In this study, the influence factors involved in EC determination were investigated using Chinese liquor as sample matrix, and the improved method was further applied. Three types of SPE columns, including diatomite, Florisil, and primary-secondary amine, were compared in extraction efficiency, and the diatomite column exhibited the highest extraction efficiency. The optimal volumes of elution solvents with diatomite column were 15 mL for 3-mL samples solution loaded. In addition, the alcoholic strength for EC determination should be diluted below 20% (v/v) to avoid the enhancement of matrix-induced chromatographic response. Moreover, the pH neutralization could help improve EC recovery and peak resolution, reducing interfering effects. Based on these results, the improved method showed that the limit of detection, the limit of quantification, and average recoveries were 1.10 µg/L, 3.65 µg/L, and 93.06%, respectively. To further elucidate the underlying factors related to EC accumulation, partial least square regression analysis was conducted, and the results suggested that EC levels had the closest relationship with alcoholic strength among the remaining precursors.

Development of dual-templates molecularly imprinted stir bar sorptive extraction and its application for the analysis of environmental estrogens in water and plastic samples.

In this study, a novel dual-template molecularly imprinted polymer (MIP)-coated stir bar was prepared and coupled with high-performance liquid chromatography (HPLC) for the analysis of environmental estrogens in complex samples. Dual-template MIP coating was homogeneous and porous with an average thickness of 5µm. Moreover, it could be used for at least 50 times and be kept for at least 12 months in a dryer without any damage. The MIP-coated stir bar showed excellent selectivity to bisphenols and steroids. The method for the determination of bisphenols and steroids in complex samples via MIP-coated stir bar sorptive extraction coupled with HPLC was developed. The method was successfully applied in the analysis of five estrogens in lake and river water samples with recoveries of 71.2- 96.4% and 62.8-98.0%, respectively. The method was also successfully applied to the analysis of five estrogens in three plastic samples with recoveries of 67.7-99.1%, 68.8-99.9%, and 74.8-101.8%. The limit of quantitation was 1.0-5.0µg/L. The proposed method is suitable for the simultaneous determination of multiple trace environmental estrogens in water and plastic samples.

Quantitative on-line preconcentration-liquid chromatography coupled with tandem mass spectrometry method for the determination of pharmaceutical compounds in water.

One of the current environmental issues concerns the presence and fate of pharmaceuticals in water bodies as these compounds may represent a potential environmental problem. The characterization of pharmaceutical contamination requires powerful analytical method able to quantify these pollutants at very low concentration (few ng L(-1)). In this work, a multi-residue analytical methodology (on-line solid phase extraction-liquid chromatography-triple quadrupole mass spectrometry using positive and negative electrospray ionization) has been developed and validated for 40 multi-class pharmaceuticals and metabolites for tap and surface waters. This on-line SPE method was very convenient and efficient compared to classical off-line SPE method because of its shorter total run time including sample preparation and smaller sample volume (1 mL vs up to 1 L). The optimized method included several therapeutic classes as lipid regulators, antibiotics, beta-blockers, non-steroidal anti-inflammatories, antineoplastic, etc., with various physicochemical properties. Quantification has been achieved with the internal standards. The limits of detection are between 0.7 and 15 ng L(-1) for drinking waters and 2-15 ng L(-1) for surface waters. The inter-day precision values are below 20% for each studied level. The improvement and strength of the analytical method has been verified along a monitoring of these 40 pharmaceuticals in Isle River, a French stream located in the South West of France. During this survey, 16 pharmaceutical compounds have been detected.

Volatile composition of peppermint (Mentha piperita L.) commercial teas through solid phase extraction

Volatiles from aqueous extract of peppermint commercial sachets were investigated through gas chromatography/flame ionization detection (GC/FID) and GC/mass spectrometry (MS). Samples were prepared under similar conditions as in homemade tea. Volatiles were isolated using solid phase extraction method (SPE) with Porapak Q trap followed by desorption with acetone. Estimated mean values for short and medium chain carboxylic acids (C2- C12) and ketones lay in the range of 50-64 μg kg-1 whilst aliphatic alcohols and acyclic hydrocarbons had values lower than 6 μg kg-1. The major volatiles were terpenes (275-382 μg kg-1) that reached 89 % of the total composition. A total of 16 compounds, among them dodecane, acetoin, acetol, citral, geraniol and octanoic acid have been described by the first time in peppermint tea. These findings could be attributed to the different analytical approach employed, mainly to the use of different extraction/pre-concentration techniques. Given the apparently lower proportion of terpenes in the aqueous extract it may be that the chemical properties of the peppermint essential oil are not entirely reproduced with homemade tea.

Estudo da composição da fração volátil do extrato aquoso de sachês de hortelã pimenta (Mentha piperita L.) através da extração em fase sólida. O princípio desse trabalho foi investigar a fração volátil do extrato aquoso de sachês comerciais de hortelã pimenta usando cromatografia gasosa com detectores de ionização em chama e de massas. As amostras foram preparadas em condições similares às usadas para o preparo do chá caseiro. Os compostos voláteis foram isolados via método de extração em fase sólida com adsorvente Porapak Q e eluídos com acetona. Uma estimativa dos valores médios dos ácidos carboxílicos de cadeias média e curta ficou na faixa de 50-64 μg kg-1, enquanto alcoóis alifáticos e hidrocarbonetos acíclicos tiveram valores menores do que 6 μg kg-1. Os terpenos (275-382 μg kg-1) foram os compostos majoritários alcançando 89 % dos sólidos totais. Um total de 16 compostos voláteis, entre eles, dodecano, acetoína, acetol, citral, geraniol e ácido octanóico foram descritos pela primeira vez no chá de hortelã pimenta. Esses resultados poderiam ser atribuídos aos diferentes métodos analíticos empregados, principalmente devido ao uso de diferentes técnicas de extração e pré-concentração. Em função da proporção menor de terpenos no extrato aquoso é razoável especular que as propriedades químicas do óleo essencial da hortelã pimenta não sejam totalmente reproduzidas com o consumo do chá caseiro.

SPE-NMR metabolite sub-profiling of urine.

NMR-based metabolite profiling of urine is a fast and reproducible method for detection of numerous metabolites with diverse chemical properties. However, signal overlap in the (1)H NMR profiles of human urine may hamper quantification and identification of metabolites. Therefore, a new method has been developed using automated solid-phase extraction (SPE) combined with NMR metabolite profiling. SPE-NMR of urine resulted in three fractions with complementary and reproducible sub-profiles. The sub-profile from the wash fraction (100 % water) contained polar metabolites; that from the first eluted fraction (10 % methanol-90 % water) semi-polar metabolites; and that from the second eluted fraction (100 % methanol) aromatic metabolites. The method was validated by analysis of urine samples collected from a crossover human nutritional intervention trial in which healthy volunteers consumed capsules containing a polyphenol-rich mixture of red wine and grape juice extract (WGM), the same polyphenol mixture dissolved in a soy drink (WGM_Soy), or a placebo (PLA), over a period of five days. Consumption of WGM clearly increased urinary excretion of 4-hydroxyhippuric acid, hippuric acid, 3-hydroxyphenylacetic acid, homovanillic acid, and 3-(3-hydroxyphenyl)-3-hydroxypropionic acid. However, there was no difference between the excreted amounts of these metabolites after consumption of WGM or WGM_Soy, indicating that the soy drink is a suitable carrier for WGM polyphenols. Interestingly, WGM_Soy induced a significant increase in excretion of cis-aconitate compared with WGM and PLA, suggesting a higher demand on the tricarboxylic acid cycle. In conclusion, SPE-NMR metabolite sub-profiling is a reliable and improved method for quantification and identification of metabolites in urine to discover dietary effects and markers of phytochemical exposure.

Validation and application of a liquid chromatography-tandem mass spectrometric method for the determination of GDC-0879 and its metabolite in dog plasma using solid phase extraction.

A liquid-chromatographic-tandem mass spectrometric (LC-MS/MS) method was developed and validated for the determination of GDC-0879 and its ketone metabolite (M1) in dog plasma to support preclinical toxicokinetic evaluation. The method consisted of solid phase extraction for sample preparation and LC-MS/MS analysis in positive ion mode using electrospray ionization for analysis. D(4)-GDC-0879 and (13)C(2)-D(2)-M1 were used as internal standards. A quadratic regression (weighted 1/concentration(2)) was used to fit calibration curves over the concentration range of 1-1000 ng/ml for both GDC-0879 and M1. The accuracy (%bias) at the lower limit of quantitation (LLOQ) was 12.0% and 2.0% for GDC-0879 and M1, respectively. The precision (%CV) for samples at the LLOQ was 11.3% and 2.6% for GDC-0879 and M1, respectively. For quality control samples at 3.00, 400 and 800 ng/ml, the between run %CV was ≤3.9% for GDC-0879 and ≤2.4% for M1. Between run %bias ranged from 4.6 to 12.0% for GDC-0879 and from -0.8 to 2.7% for M1. GDC-0879 and M1 were stable in dog plasma for at least 44 days at -70 °C.

Standardized LC-MS/MS based steroid hormone profile-analysis.

In order to overcome many limitations of immunoassays, high performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) has the potential to find its place in the clinical laboratory medicine for quantification of steroid hormones. A prerequisite for the application of a new analytical procedure in clinical diagnostics is standardization to minimize analytical intra- and interlaboratory variability and inaccuracy. We evaluate a newly standardized HPLC-MS/MS assay in kit-format, developed for routine determination of 16 steroid hormones in human serum samples. Fifteen metabolites can be measured quantitatively, which include aldosterone, androstenedione, androsterone, corticosterone, cortisol, cortisone, 11-deoxycortisol, dehydroepiandrosterone (DHEA), dehydroepiandrosterone sulfate (DHEAS), 17ß-estradiol (E2), estrone (E1), etiocholanolone, 17α-hydroxyprogesterone (17OHP), progesterone, and testosterone. 11-Deoxycorticosterone is the only compound rated as semi-quantitative in this kit. The sample preparation is performed by solid phase extraction (SPE) on a 96-well plate. The standardized assay has been validated for human serum in terms of lower and upper limit of quantification (LLOQ 0.01-32 ng/mL, ULOQ 5-8000 ng/mL), linear correlation coefficient of calibration (R(2)>0.9966), intra- and inter-day precision (intra-day 1.1-8.8%, inter-day 5.2-14.8% and 8.2-18.6% for 11-deoxycorticosterone), accuracy (intra-day 88.3-115.5% and 109.3-128.2% for 11-deoxycorticosterone, inter-day 91.4-117.2% and 102.3-137.1% for 11-deoxycorticosterone), analytical total error (3.6-17.8%), proficiency test accuracy (85.4-113.4%), recovery (68-99%), and metabolite stability (freeze/thaw stability 95.5-108.1%, short term stability 86.9-107.2%). Inter-assay comparison with a routine reference HPLC-MS/MS assay and seven immunoassays demonstrates the outstanding high performance of this HPLC-MS/MS based kit by improvements in accuracy for progesterone, androstenedione, and 17OHP. Finally, results of two metyrapone tests demonstrate the potential of the standardized HPLC-MS/MS assay for the analysis of a comprehensive steroid hormone profile in clinical diagnostics.

Determination of cadmium in water samples by liquid electrode plasma atomic emission spectrometry after solid phase extraction using a mini cartridge packed with chelate resin immobilizing carboxymethylated pentaethylenehexamine.

Solid phase extraction using a mini cartridge packed with 22 mg of chelate resin immobilizing carboxymethylated pentaethylenehexamine was successfully utilized for separation/preconcentration of cadmium in water samples prior to liquid electrode plasma atomic emission spectrometric (LEP-AES) determination. The combined method with the extraction and LEP-AES was applicable to the determination of cadmium in the certified reference materials (EU-L-1 wastewater and ES-L-1 groundwater); the detection limit was 0.20 microg in 200 mL of sample solution (500-fold preconcentration).

Combination of solid phase extraction and in vial solid phase derivatization using a strong anion exchange disk for the determination of nerve agent markers.

Alkylphosphonic acids (APAs) are degradation products and chemical markers of organophosphorous (OP) nerve agents (chemical warfare agents). Anion exchange disk-based solid phase extraction (SPE) has been combined with in vial solid phase derivatization (SPD) and GC-MS analysis for the determination of APAs in aqueous samples. The optimization of critical method parameters, such as the SPD reaction, was achieved using statistical experimental design and multivariate data analysis. The optimized method achieved quantitative recoveries in the range from 83% to 101% (n=13, RSD from 4% to 10%). The method was sensitive, with LODs in SIM mode of 0.14 ppb, and demonstrated excellent linearity with an average R(2)>or=0.99 over the concentration range of 0.07-1.4 ppm in full scan mode and from 0.14 ppb to 14 ppb in SIM mode. For forensic applications, aqueous samples containing APAs at concentrations exceeding 14 ppb were concentrated and target analytes were successfully identified by spectral library and retention index matching. Method robustness was evaluated using aqueous samples from the official OPCW Proficiency Test (round 19) and all APAs present in the sample were conclusively identified. The SPE disk retained the underivatized APAs in a stable condition for extended periods of time. No significant losses of APAs from the disk were observed over a 36-day period. Overall, the method is well suited to the qualitative and quantitative analysis of degradation markers of OP nerve agents in aqueous matrices with simplicity, a low risk of cross-contamination and trace level sensitivity.

Relative influence of the dissolved humic material on the solid-phase extraction efficiency of pesticides from environmental water.

The effect of organic matter on the solid-phase extraction (SPE) efficiency for pesticides belonging to different chemical groups (urea-derivatives, carbamates and triazines) and having different polarities, was simultaneously studied for the first time in pure and simulated water samples. SPE was carried out in precolumns packed with C18 silica or styrene-divinylbenzene copolymer PLRP-S phases on-line coupled to high performance liquid chromatography (HPLC) analysis. Retention factors in water (k'(W)) were estimated for 25 compounds and used for the calculation of the theoretical breakthrough volume (Vb(T)) in pure water. Experimental breakthrough volumes (Vb(E)) were first determined using purified and deionized water as the matrix for selected compounds having Vb(T) < 500 mL; then, the same water with an added humic acid sodium salt (HA) at 0.4-5.6 mg/L of dissolved organic carbon (DOC) content, was used as the matrix for compounds having VbE < 500 mL in pure water. Several polar pesticides showed negative linear or logarithmic Vb(E) curves depending on HA content; their recoveries were also determined in environmental samples having low dissolved organic carbon values, between 0.5-6.4 mg/L. A similar behavior was observed for these compounds in simulated and natural water samples, where DOC concentration and the percolated volume (Vp) mainly determine the solute recoveries values. However, the variation of recoveries as a function of DOC content could be negative or null depending on the two examined conditions (Vp lower or larger than Vb(E) in pure water). Results demonstrated that breakthrough volume must always be considered to correctly interpret the participation of dissolved humic material on the SPE efficiency of organic micropollutants in water.