Production of Disinfective Coating Layer to Facial Masks Supplemented with Camellia sinensis Extract.

Although usefulness of masks for protection against respiratory pathogens, accumulation of pathogens on their surface represents a source of infection spread. Here we prepared a plant extract-based disinfecting layer to be used in coating masks thus inhibiting their capacity to transmit airborne pathogens. To reach this, a polypropylene membrane base was coated with a layer of polyvinyledine difluoride polymer containing 500 µg/ml of Camellia sinensis (Black tea) methanolic extract. Direct inhibitory effects of C. sinensis were initially demonstrated against Staphylococcus aureus (respiratory bacteria), influenza A virus (enveloped virus) and adenovirus 1 (non-enveloped virus) which were directly proportional to both extract concentration and incubation time with the pathogen. This was later confirmed by the capacity of the supplemented membrane with the plant extract to block infectivity of the above mentioned pathogens, recorded % inhibition values were 61, 72 and 50 for S. aureus, influenza and adenovirus, respectively. In addition to the disinfecting capacity of the membrane its hydrophobic nature and pore size (154 nm) prevented penetration of dust particles or water droplets carrying respiratory pathogens. In summary, introducing this layer could protect users from infection and decrease infection risk upon handling contaminated masks surfaces.

Unfolding the effects of decontamination treatments on the structural and functional integrity of N95 respirators via numerical simulations.

Filtering facepiece respirators (FFRs) provide effective protection against diseases spread through airborne infectious droplets and particles. The widespread use of FFRs during the COVID-19 pandemic has not only led to supply shortages, but the disposal of single-use facemasks also threatens the environment with a new kind of plastic pollution. While limited reuse of filtering facepiece respirators has been permitted as a crisis capacity strategy, there are currently no standard test methods available for decontamination before their repeated use. The decontamination of respirators can compromise the structural and functional integrity by reducing the filtration efficiency and breathability. Digital segmentation of X-ray microcomputed tomography (microCT) scans of the meltblown nonwoven layers of a specific N95 respirator model (Venus-4400) after treatment with one and five cycles of liquid hydrogen peroxide, ultraviolet radiation, moist heat, and aqueous soap solution enabled us to perform filtration simulations of decontaminated respirators. The computed filtration efficiencies for 0.3 µm particles agreed well with experimental measurements, and the distribution of particle penetration depths was correlated with the structural changes resulting from decontamination. The combination of X-ray microCT imaging with numerical simulations thus provides a strategy for quantitative evaluation of the effectiveness of decontamination treatments for a specific respirator model.

Adaptação cultural e validação da reason of using face masks cale para brasileiros / Adaptación cultural y validación de la reason of using face mask scale para brasileños / Cultural adaptation and validation of the reason of using face mask scale for brazilians

RESUMO Objetivo: realizar a tradução, adaptação cultural e validação da Reason of Using Face Mask Scale entre brasileiros. Métodos: estudo metodológico realizado entre abril e maio de 2020 mediante as seguintes etapas: tradução; síntese das traduções; retrotradução; comitê de juízes; pré-teste e avaliação das propriedades psicométricas. A coleta dos dados foi online a partir de mensagens enviadas por meio de mídias sociais. O questionário foi disponibilizado a partir de um link e os dados armazenados no Google Forms. Utilizou-se a Análise Fatorial Exploratória, testes de Kaiser-Meyer-Olkin e de Esfericidade de Bartlett para constatar se a amostra era adequada e passível de fatoração. Resultados: a escala foi traduzida para o português, avaliada por cinco especialistas, pré-testada com 20 adultos e aplicada em 500 pessoas da população brasileira. O índice de validade de conteúdo para a escala como um todo foi de 0,92. Os valores de Kaiser-Meyer-Olkin (0,639) e teste de esfericidade de Bartlett (p=0,000) indicaram que os itens eram fatoráveis. A variância explicada foi de 62,18%. Na validade de construto por grupos distintos, obteve-se resultado satisfatório (p<0,05). Conclusão: a Versão Brasileira da escalafoi adaptada para a cultura brasileira, sendo válida para avaliar os motivos para o uso de máscaras entre brasileiros.

RESUMEN Objetivo: realizar la traducción, adaptación cultural y validación de la Reason ofUsingFaceMaskScale entre brasileños. Métodos: estudio metodológico realizado entre abril y mayo de 2020 a través de las siguientes etapas: traducción; síntesis de las traducciones; retrotraducción; evaluación por jueces; pretest y evaluación de las propiedades psicométricas. La recolección de datos se realizó online a partir de mensajes enviados a través de redes sociales. La encuesta se hizo disponible a partir de un enlace y los datos almacenados en Google Forms. Se utilizó el Análisis Factorial Exploratorio, pruebas de Kaiser-Meyer-Olkin y de Esfericidad de Bartlett para determinar si la muestra era adecuada y susceptible a la factorización. Resultados: la escala fue traducida al portugués, evaluada por cinco especialistas, pre-testada con 20 adultos y aplicada en 500 personas de la población brasileña. El índice de validez del contenido para la escala como un todo fue de 0,92. Los valores de Kaiser-Meyer-Olkin (0,639) y test de esfericidad de Bartlett (p=0,000) indicaron que los ítems eran susceptibles a la factorización. La varianza explicada fue de 62,18%. En la validez de constructo por grupos distintos se obtuvo resultado satisfactorio (p<0,05). Conclusión: la Versión Brasileña de la escala fue adaptada para la cultura brasileña yes válida para evaluar los motivos para el uso de máscaras entre brasileños.

ABSTRACT Objective: to carry out the translation, cultural adaptation and validation of the Reason of Using Face Mask Scale among Brazilians. Methods: methodological study conducted between April and May 2020 using the following steps: translation; synthesis of translations; back-translation; committee of judges; pre-test and evaluation of psychometric properties. Data collection took place online from messages sent through social media. The questionnaire was made available from a link and the data stored in Google Forms. Exploratory Factor Analysis, Kaiser-Meyer-Olkin and Bartlett's Sphericity tests were used to check if the sample was adequate and factorable. Results: the scale was translated into Portuguese, evaluated by five experts, pre-tested with 20 adults and applied to 500 people from the Brazilian population. The content validity index for the scale as a whole was 0.92. The Kaiser-Meyer-Olkin (0.639) and Bartlett's Sphericity test (p=0.000) values indicated that the items were factorable. The explained variance was 62.18%. In the construct validity for different groups, a satisfactory result was obtained (p<0.05). Conclusion: the Brazilian Version of the scale was adapted to the Brazilian culture and is valid to evaluate the reasons for the use of masks among Brazilians.

New novel thermal insulation and sound-absorbing materials from discarded facemasks of COVID-19 pandemic.

Due to the COVID-19 pandemic, people were encouraged and sometimes required to wear disposable facemasks, which then are discarded creating an environmental problem. In this study, we aim at investigating novel ideas to recycle wasted facemasks in order to lower the environmental impact. An experimental study has been carried out to investigate the possibility of using discarded masks for thermal insulation and sound absorption. The wasted masks are simulated by new masks, which stripped off the nose clips, elastic ear loops and are heated to 120 °C for one hour to kill any biological contaminants. The masks are also melted to investigate their thermal insulation and sound absorption properties. Results show that the thermal conductivity coefficients of the loose and melted masks are 0.03555 and 0.08683 W/m K, respectively, at room temperature of about 25 °C. Results show also that the sound absorption coefficient for loose masks is above 0.6 for the frequency range 600-5000 Hz. The loose facemasks are found to be thermally stable up to 295 °C, elastic ear loops at 304.7 °C, and the composite (melted) facemasks at 330.0 °C using the thermo-gravimetric analysis. Characterization of the facemask's three-layer fibers and the composite (melted) samples is obtained using scanning electron microscopy (SEM). The three-point bending test is obtained for the composite specimens showing good values of flexural stress, flexural strain, and flexural elastic modulus. These results are promising about using such discarded masks as new thermal insulation and sound-absorbing materials for buildings replacing the synthetic or petrochemical insulation materials.

Durable nanocomposite face masks with high particulate filtration and rapid inactivation of coronaviruses.

The COVID-19 pandemic presents a unique challenge to the healthcare community due to the high infectivity rate and need for effective personal protective equipment. Zinc oxide nanoparticles have shown promising antimicrobial properties and are recognized as a safe additive in many food and cosmetic products. This work presents a novel nanocomposite synthesis approach, which allows zinc oxide nanoparticles to be grown within textile and face mask materials, including melt-blown polypropylene and nylon-cotton. The resulting nanocomposite achieves greater than 3 log10 reduction (≥ 99.9%) in coronavirus titer within a contact time of 10 min, by disintegrating the viral envelope. The new nanocomposite textile retains activity even after 100 laundry cycles and has been dermatologist tested as non-irritant and hypoallergenic. Various face mask designs were tested to improve filtration efficiency and breathability while offering antiviral protection, with Claros' design reporting higher filtration efficiency than surgical masks (> 50%) for particles ranged 200 nm to 5 µm in size.

UV decontamination of personal protective equipment with idle laboratory biosafety cabinets during the COVID-19 pandemic.

Personal protective equipment (PPE) is crucially important to the safety of both patients and medical personnel, particularly in the event of an infectious pandemic. As the incidence of Coronavirus Disease 2019 (COVID-19) increases exponentially in the United States and many parts of the world, healthcare provider demand for these necessities is currently outpacing supply. In the midst of the current pandemic, there has been a concerted effort to identify viable ways to conserve PPE, including decontamination after use. In this study, we outline a procedure by which PPE may be decontaminated using ultraviolet (UV) radiation in biosafety cabinets (BSCs), a common element of many academic, public health, and hospital laboratories. According to the literature, effective decontamination of N95 respirator masks or surgical masks requires UV-C doses of greater than 1 Jcm-2, which was achieved after 4.3 hours per side when placing the N95 at the bottom of the BSCs tested in this study. We then demonstrated complete inactivation of the human coronavirus NL63 on N95 mask material after 15 minutes of UV-C exposure at 61 cm (232 µWcm-2). Our results provide support to healthcare organizations looking for methods to extend their reserves of PPE.

Screening of core filter layer for the development of respiratory mask to combat COVID-19.

The severe outbreak of respiratory coronavirus disease 2019 has increased the significant demand of respiratory mask and its use become ubiquitous worldwide to control this unprecedented respiratory pandemic. The performance of a respiratory mask depends on the efficiency of the filter layer which is mostly made of polypropylene melt blown non-woven (PP-MB-NW). So far, very limited characterization data are available for the PPE-MB-NW in terms to achieve desired particulate filtration efficiency (PFE) against 0.3 µm size, which are imperative in order to facilitate the right selection of PP-MB-NW fabric for the development of mask. In present study, eight different kinds of PP-MB-NW fabrics (Sample A-H) of varied structural morphology are chosen. The different PP-MB-NW were characterized for its pore size and distribution by mercury porosimeter and BET surface area analyzer was explored first time to understand the importance of blind pore in PFE. The PP-MB-NW samples were characterized using scanning electron microscopy so as to know the surface morphology. The filtration efficiency, pressure drop and breathing resistance of various PP-MB-NW fabric samples are investigated in single and double layers combination against the particle size of 0.3, 0.5 and 1 µm. The samples which are having low pore dia, high solid fraction volume, and low air permeability has high filtration efficiency (> 90%) against 0.3 µm particle with high pressure drop (16.3-21.3 mm WC) and breathing resistance (1.42-1.92 mbar) when compared to rest of the samples. This study will pave the way for the judicial selection of right kind of filter layer i.e., PP-MB-NW fabric for the development of mask and it will be greatly helpful in manufacturing of mask in this present pandemic with desired PFE indicating considerable promise for defense against respiratory pandemic.

Pulsed Broad-Spectrum UV Light Effectively Inactivates SARS-CoV-2 on Multiple Surfaces and N95 Material.

The ongoing SARS-CoV-2 pandemic has resulted in an increased need for technologies capable of efficiently disinfecting public spaces as well as personal protective equipment. UV light disinfection is a well-established method for inactivating respiratory viruses. Here, we have determined that broad-spectrum, pulsed UV light is effective at inactivating SARS-CoV-2 on multiple surfaces in vitro. For hard, non-porous surfaces, we observed that SARS-CoV-2 was inactivated to undetectable levels on plastic and glass with a UV dose of 34.9 mJ/cm2 and stainless steel with a dose of 52.5 mJ/cm2. We also observed that broad-spectrum, pulsed UV light is effective at reducing SARS-CoV-2 on N95 respirator material to undetectable levels with a dose of 103 mJ/cm2. We included UV dosimeter cards that provide a colorimetric readout of UV dose and demonstrated their utility as a means to confirm desired levels of exposure were reached. Together, the results presented here demonstrate that broad-spectrum, pulsed UV light is an effective technology for the in vitro inactivation of SARS-CoV-2 on multiple surfaces.

Suitability of DIALux for designing UVC disinfection cabins.

During the present Sars-CoV-2 pandemic, there has been an increase in the development of UVC disinfection systems. Researchers and members of the lighting community shifted their interests to this new field to help develop systems for disinfecting facemasks and other small equipment. In this paper we show that it is possible to use DIALux to simulate the irradiance distribution provided by a lamp emitting in the UVC range. We will compare the results provided by DIALux with those obtained from Zemax OpticStudio in three different scenarios. We compared the minimum, maximum, and mean irradiance at the detection plane. The differences between the two software were less than 12%, 2%, and 6%, respectively. We also compared the contour maps of isoirradiance lines. We conclude that DIALux is well suited for UVC lighting design in the UVC range. We think that this finding will contribute to increasing the design and manufacturing of new UVC disinfection systems needed to fight against the Sars-CoV-2 pandemic.

Decontamination of N95 and surgical masks using a treatment based on a continuous gas phase-Advanced Oxidation Process.

A gas-phase Advanced Oxidation Process (gAOP) was evaluated for decontaminating N95 and surgical masks. The continuous process was based on the generation of hydroxyl-radicals via the UV-C (254 nm) photo-degradation of hydrogen peroxide and ozone. The decontamination efficacy of the gAOP was dependent on the orientation of the N95 mask passing through the gAOP unit with those positioned horizontally enabling greater exposure to hydroxyl-radicals compared to when arranged vertically. The lethality of gAOP was independent of the applied hydrogen peroxide concentration (2-6% v/v) but was significantly (P<0.05) higher when H2O2 was introduced into the unit at 40 ml/min compared to 20 ml/min. A suitable treatment for N95 masks was identified as 3% v/v hydrogen peroxide delivered into the gAOP reactor at 40 ml/min with continuous introduction of ozone gas and a UV-C dose of 113 mJ/cm2 (30 s processing time). The treatment supported >6 log CFU decrease in Geobacillus stearothermophilus endospores, > 8 log reduction of human coronavirus 229E, and no detection of Escherichia coli K12 on the interior and exterior of masks. There was no negative effect on the N95 mask fitting or particulate efficacy after 20 passes through the gAOP system. No visual changes or hydrogen peroxide residues were detected (<1 ppm) in gAOP treated masks. The optimized gAOP treatment could also support >6 log CFU reduction of endospores inoculated on the interior or exterior of surgical masks. G. stearothermophilus Apex spore strips could be applied as a biological indicator to verify the performance of gAOP treatment. Also, a chemical indicator based on the oxidative polymerization of pyrrole was found suitable for reporting the generation of hydroxyl-radicals. In conclusion, gAOP is a verifiable treatment that can be applied to decontaminate N95 and surgical masks without any negative effects on functionality.

Negative-Pressure Isolation Mask for Endoscopic Examination During the Coronavirus Disease 2019 Pandemic: A Randomized Controlled Trial.

INTRODUCTION: During the coronavirus disease 2019 (COVID-19) pandemic, endoscopists have high risks of exposure to exhaled air from patients during gastroscopy. To minimize this risk, we transformed the oxygen mask into a fully closed negative-pressure gastroscope isolation mask. This study aimed to evaluate the effectiveness, safety, and feasibility of use of this mask during gastroscopy. METHODS: From February 28, 2020, to March 10, 2020, 320 patients undergoing gastroscopy were randomly assigned into the mask group (n = 160) or conventional group (n = 160). Patients in the mask group wore the isolation mask during gastroscopy, whereas patients in the conventional group did not wear the mask. The adenosine triphosphate fluorescence and carbon dioxide (CO2) concentration in patients' exhaled air were measured to reflect the degree of environmental pollution by exhaled air. Patients' vital signs, operation time, and adverse events during endoscopy were also evaluated. RESULTS: Four patients were excluded because of noncooperation or incomplete data. A total of 316 patients were included in the final analysis. The difference between the highest CO2 concentration around patients' mouth and CO2 concentration in the environment was significantly decreased in the mask group compared with the conventional group. There was no significant difference in the adenosine triphosphate fluorescence, vital signs, and operation time between the 2 groups. No severe adverse events related to the isolation mask, endoscopy failure, or new coronavirus infection during follow-up were recorded. DISCUSSION: This new isolation mask showed excellent feasibility of use and safety compared with routine gastroscopy during the COVID-19 pandemic.

Personal protective equipment for reducing the risk of COVID-19 infection among health care workers involved in emergency trauma surgery during the pandemic: An umbrella review.

BACKGROUND: Health care facilities in low- and middle-income countries are inadequately resourced to adhere to current COVID-19 prevention recommendations. Recommendations for surgical emergency trauma care measures need to be adequately informed by available evidence and adapt to particular settings. To inform future recommendations, we set to summarize the effects of different personal protective equipment (PPE) on the risk of COVID-19 infection in health personnel caring for trauma surgery patients. METHODS: We conducted an umbrella review using Living Overview of Evidence platform for COVID-19, which performs regular automated searches in MEDLINE, Embase, Cochrane Central Register of Controlled Trials, and more than 30 other sources. Systematic reviews of experimental and observational studies assessing the efficacy of PPE were included. Indirect evidence from other health care settings was also considered. Risk of bias was assessed with the AMSTAR II tool (Assessing the Methodological Quality of Systematic Reviews, Ottawa, ON, Canada), and the Grading of Recommendations, Assessment, Development, and Evaluation approach for grading the certainty of the evidence is reported (registered in International Prospective Register of Systematic Reviews, CRD42020198267). RESULTS: Eighteen studies that fulfilled the selection criteria were included. There is high certainty that the use of N95 respirators and surgical masks is associated with a reduced risk of COVID-19 when compared with no mask use. In moderate- to high-risk environments, N95 respirators are associated with a further reduction in risk of COVID-19 infection compared with surgical masks. Eye protection also reduces the risk of contagion in this setting. Decontamination of masks and respirators with ultraviolet germicidal irradiation, vaporous hydrogen peroxide, or dry heat is effective and does not affect PPE performance or fit. CONCLUSION: The use of PPE drastically reduces the risk of COVID-19 compared with no mask use in health care workers. N95 and equivalent respirators provide more protection than surgical masks. Decontamination and reuse appear feasible to overcome PPE shortages and enhance the allocation of limited resources. These effects are applicable to emergency trauma care and should inform future recommendations. LEVEL OF EVIDENCE: Review, level II.

Reducing Aerosolized Particles and Droplet Spread in Endoscopic Sinus Surgery during COVID-19.

OBJECTIVES: The presence of high SARS-Cov-2 viral loads in the upper airway, including the potential for aerosolized transmission of viral particles, has generated significant concern amongst otolaryngologists worldwide, particularly those performing endoscopic sinus surgery (ESS). We evaluated a simple negative-pressure mask technique to reduce viral exposure. METHODS: Two models simulating respiratory droplets >5-10 µm and fine respiratory nuclei <5 µm using fluorescein dye and wood smoke, respectively, were utilized in a fixed cadaveric study in a controlled environment. Using ultraviolet light, fluorescein droplet spread was assessed during simulated ESS with powered microdebrider and powered drilling. Wood smoke ejection was used to evaluate fine particulate escape from a negative-pressure mask using digital subtraction image processing. RESULTS: The use of a negative-pressure mask technique resulted in 98% reduction in the fine particulate aerosol simulation and eliminated larger respiratory droplet spread during simulated ESS, including during external drill activation. CONCLUSIONS: As global ear, nose & throat (ENT) services resume routine elective operating, we demonstrate the potential use of a simple negative-pressure mask technique to reduce the risk of viral exposure for the operator and theatre staff during ESS. LEVEL OF EVIDENCE: 5 Laryngoscope, 131:956-960, 2021.

Locally produced personal protective equipment can offer hospital staff protection against Covid-19 if combined with surgical masks and rigorous personal protective equipment cleaning routine.

Locally made, washable and reusable personal protective equipment (PPE), used in combination with N95 masks that were reused safely, has proven to be a viable alternative to disposable gowns and caps for hospital staff in low- and middle-income countries. Muhimbili University Hospital's children's cancer ward in Dar es Salaam, Tanzania, developed locally made PPE and created rigorous cleaning and disinfecting protocols, when the daily use of imported, disposable materials were not an option. These items continue to protect staff, children and parents. The novel PPE approach was able to prevent staff from becoming infected during the pandemic despite the fact that several parents, and subsequently their children, became infected with Covid-19 during cancer treatment at the facility.

Decontamination of filtering facepiece respirators using a low-temperature-steam-2%-formaldehyde sterilization process during a pandemic: a safe alternative for re-use.

BACKGROUND: The coronavirus disease 2019 pandemic has caused problems with respirator supplies. Re-use may minimize the impact of the shortage, but requires the availability of an efficient and safe decontamination method. AIM: To determine whether low-temperature-steam-2%-formaldehyde (LTSF) sterilization is effective, preserves the properties of filtering facepiece (FFP) respirators and allows safe re-use. METHODS: Fourteen unused FFP2, FFP3 and N95 respirator models were subjected to two cycles of decontamination cycles. After the second cycle, each model was inspected visually and accumulated residual formaldehyde levels were analysed according to EN 14180. After one and two decontamination cycles, the fit factor (FF) of each model was tested, and penetration tests with sodium chloride aerosols were performed on five models. FINDINGS: Decontamination physically altered three of the 14 models. All of the residual formaldehyde values were below the permissible threshold. Irregular decreases and increases in FF were observed after each decontamination cycle. In the sodium chloride aerosol penetration test, three models obtained equivalent or superior results to those of the FFP classification with which they were marketed, both at baseline and after one and two cycles of decontamination, and two models had lower filtering capacity. CONCLUSION: One and two decontamination cycles using LTSF did not alter the structure of most (11/14) respirators tested, and did not degrade the fit or filtration capacity of any of the analysed respirators. The residual formaldehyde levels complied with EN 14180. This reprocessing method could be used in times of shortage of personal protective equipment.

A hybrid model integrating warm heat and ultraviolet germicidal irradiation might efficiently disinfect respirators and personal protective equipment.

BACKGROUND: The pandemic coronavirus disease 2019 (COVID-19) has taken a heavy toll on human life and has upended the medical system in many countries. The disease has created a system wide worsening shortage of N95, medical masks, and other personal protective equipment (PPE) that is regularly used by healthcare personnel and emergency service providers for their protection. AIM: Considering the number of infected patients and the stressed supplies of PPE, reuse of PPE can serve as an efficient contingency plan. Multiple studies have investigated the effect of different decontamination methods. METHODS: We chose the most user-friendly, easily scalable viral decontamination methods, including ultraviolet irradiation and heat treatment. In this paper, we investigated a unique approach to reuse the mask by creating a hybrid model that efficiently sanitizes the infected mask. RESULTS: The advantages of the proposed hybrid model as compared to the respective single arms is its decontamination efficacy, operational speed, as well as the number of reuse cycles as verified by mathematical analysis and simulation. This model is mainly intended for medical PPE but can also be used for other domestic and personal sanitization during the COVID-19 pandemic. As per the situation, the hybrid system can be used as standalone systems also. This sanitization process is not only limited to the elimination of Severe acute respiratory syndrome coronavirus 2 but can be extended to any other infectious agents. Thus, our results indicate that the proposed hybrid system is more effective, meets disinfection criterion and time saving for the reuse of respirators and PPE.

Decontamination of SARS-CoV-2 and Other RNA Viruses from N95 Level Meltblown Polypropylene Fabric Using Heat under Different Humidities.

In March of 2020, the World Health Organization declared a pandemic of coronavirus disease 2019 (COVID-19), caused by the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). The pandemic led to a shortage of N95-grade filtering facepiece respirators (FFRs), especially surgical-grade N95 FFRs for protection of healthcare professionals against airborne transmission of SARS-CoV-2. We and others have previously reported promising decontamination methods that may be applied to the recycling and reuse of FFRs. In this study we tested disinfection of three viruses, including SARS-CoV-2, dried on a piece of meltblown fabric, the principal component responsible for filtering of fine particles in N95-level FFRs, under a range of temperatures (60-95 °C) at ambient or 100% relative humidity (RH) in conjunction with filtration efficiency testing. We found that heat treatments of 75 °C for 30 min or 85 °C for 20 min at 100% RH resulted in efficient decontamination from the fabric of SARS-CoV-2, human coronavirus NL63 (HCoV-NL63), and another enveloped RNA virus, chikungunya virus vaccine strain 181/25 (CHIKV-181/25), without lowering the meltblown fabric's filtration efficiency.

The effect of ultraviolet C radiation against different N95 respirators inoculated with SARS-CoV-2.

OBJECTIVES: There are currently no studies that have examined whether one dosage can be uniformly applied to different respirator types to effectively decontaminate SARS-CoV-2 on N95 filtering facepiece respirators (FFRs). Health care workers have been using this disinfection method during the pandemic. Our objective was to determine the effect of UVC on SARS-CoV-2 inoculated N95 respirators and whether this was respirator material/model type dependent. METHODS: Four different locations (facepiece and strap) on five different N95 FFR models (3M 1860, 8210, 8511, 9211; Moldex 1511) were inoculated with a 10 µL drop of SARS-CoV-2 viral stock (8 × 107 TCID50/mL). The outside-facing and wearer-facing surfaces of the respirators were each irradiated with a dose of 1.5 J/cm2 UVC (254 nm). Viable SARS-CoV-2 was quantified by a median tissue culture infectious dose assay (TCID50). RESULTS: UVC delivered using a dose of 1.5 J/cm2, to each side, was an effective method of decontamination for the facepieces of 3M 1860 and Moldex 1511, and for the straps of 3M 8210 and the Moldex 1511. CONCLUSION: This dose is an appropriate decontamination method to facilitate the reuse of respirators for healthcare personnel when applied to specific models/materials. Also, some straps may require additional disinfection to maximize the safety of frontline workers. Implementation of widespread UVC decontamination methods requires careful consideration of model, material type, design, and fit-testing following irradiation.

Dry heat and microwave-generated steam protocols for the rapid decontamination of respiratory personal protective equipment in response to COVID-19-related shortages.

BACKGROUND: In the wake of the SARS-CoV-2 pandemic and unprecedented global demand, clinicians are struggling to source adequate access to personal protective equipment. Respirators can be in short supply, though are necessary to protect workers from SARS-CoV-2 exposure. Rapid decontamination and reuse of respirators may provide relief for the strained procurement situation. METHOD: In this study, we investigated the suitability of 70°C dry heat and microwave-generated steam (MGS) for reprocessing of FFP2/N95-type respirators, and Type-II surgical face masks. Staphylococcus aureus was used as a surrogate as it is less susceptible than enveloped viruses to chemical and physical processes. RESULTS: We observed >4 log10 reductions in the viability of dry S. aureus treated by dry heat for 90 min at 70°C and >6 log10 reductions by MGS for 90 s. After 3 reprocessing cycles, neither process was found to negatively impact the bacterial or NaCl filtration efficiency of the respirators that were tested. However, MGS was incompatible with Type-II surgical masks tested, as we confirmed that bacterial filtration capacity was completely lost following reprocessing. MGS was observed to be incompatible with some respirator types due to arcing observed around some types of metal nose clips and by loss of adhesion of clips to the mask. CONCLUSION: Considering the advantages and disadvantages of each approach, we propose a reprocessing personal protective equipment/face mask workflow for use in medical areas.

Filtration Efficiencies of Nanoscale Aerosol by Cloth Mask Materials Used to Slow the Spread of SARS-CoV-2.

Filtration efficiency (FE), differential pressure (ΔP), quality factor (QF), and construction parameters were measured for 32 cloth materials (14 cotton, 1 wool, 9 synthetic, 4 synthetic blends, and 4 synthetic/cotton blends) used in cloth masks intended for protection from the SARS-CoV-2 virus (diameter 100 ± 10 nm). Seven polypropylene-based fiber filter materials were also measured including surgical masks and N95 respirators. Additional measurements were performed on both multilayered and mixed-material samples of natural, synthetic, or natural-synthetic blends to mimic cloth mask construction methods. Materials were microimaged and tested against size selected NaCl aerosol with particle mobility diameters between 50 and 825 nm. Three of the top five best performing samples were woven 100% cotton with high to moderate yarn counts, and the other two were woven synthetics of moderate yarn counts. In contrast to recently published studies, samples utilizing mixed materials did not exhibit a significant difference in the measured FE when compared to the product of the individual FE for the components. The FE and ΔP increased monotonically with the number of cloth layers for a lightweight flannel, suggesting that multilayered cloth masks may offer increased protection from nanometer-sized aerosol with a maximum FE dictated by breathability (i.e., ΔP).