Resection to restoration: Assessing the synergy of polypropylene mesh (Marlex®) combined with methyl-methacrylate and latissimus dorsi flap for primary chest wall sarcomas.

BACKGROUND: Chest-wall sarcomas are treated with extensive resections and complex defect reconstruction to restore chest-wall integrity. It is a difficult surgical procedure that incorporates a multidisciplinary approach for the best outcome, preventing paradoxical chest movement issues and reducing complications. OBJECTIVE: We aimed to describe our experience of chest-wall reconstruction using polypropylene mesh (Marlex® Mesh) combined with methyl-methacrylate and soft-tissue coverage with a latissimus dorsi flap following sarcoma resection. PATIENTS AND METHODS: Among the 53 patients treated for primary chest-wall sarcomas at the European Institute of Oncology (IEO) in Milan, Italy, from 1998 to 2020, 14 cases underwent chest-wall resection and reconstruction using polypropylene mesh, methyl-methacrylate and the latissimus dorsi flap. Patients with locally advanced breast cancers, locally advanced lung cancers, squamous cell carcinomas, and other secondary chest-wall malignancies were excluded from the study, as were the patients with different types of chest-wall reconstruction. RESULTS: In this study, 14 patients (6 men and 8 women) with various primary chest-wall sarcomas were enrolled. On an average, 2 ribs (range: 1-5) were removed during the surgeries, and the chest-wall defects ranged from 20 to 150 cm2 with an average size of 73 cm2. The mean follow-up period for these patients was approximately 63.80 months CONCLUSION: The combination of Marlex® mesh filled with methyl-methacrylate and covered using latissimus dorsi myocutaneous flap provides safe, low-cost and effective single-stage chest-wall reconstruction after surgery for primary sarcomas.

Modified Goldner Trichrome for Non-decalcified Mineralized Tissue Plastinated and Embedded in Resin / Tricrómico de Goldner Modificado para Tejido Mineralizado no Descalcificado Plastinado e Incluido en resina

SUMMARY: Over time, Goldner's trichrome staining has been essential in paraffin soft tissue research. However, its classic application involves prior decalcification, generating disadvantages in the integrity of the samples and the interpretation of results. This study seeks to overcome the limitations associated with decalcification when applying Goldner's trichrome stain with plastic resins. It focuses on detailed visualization of non-decalcified bone and dental samples in animal models. Samples of jaw and tooth from a dog (Canis familiaris) were used, as well as tibia from a rabbit (Oryctolagus cuniculus) with a titanium dental implant and bone graft substitute. Adjustments were made to the original protocol, including a surface treatment prior to staining. Plastination and inclusion in specific plastic resins were part of the process. The microplastinated and stained samples showed optimal quality for optical microscopy. Those from dogs allowed detailed observation of the tooth-periodontal tissue relationship, while those from rabbits revealed a clear differentiation between mineralized and osteoid bone tissue. The staining made it easy to examine the precise interface between soft tissues, bone graft, and implant. The successful adaptation of Goldner's trichrome stain to specimens in plastic resins represents a significant advance in histological investigation of hard tissues. This methodology stands out as an effective tool to evaluate implants and biomaterials in animal models, providing detailed visualization without compromising the integrity of the samples. The combination of histochemistry and plastic resins offers a valuable alternative for microanatomical studies, opening new possibilities in hard tissue research and evaluation of bone structures.

A lo largo del tiempo, la tinción tricrómica de Goldner ha sido esencial en la investigación de tejidos blandos en parafina. Sin embargo, su aplicación clásica conlleva la descalcificación previa, generando desventajas en la integridad de las muestras y la interpretación de resultados. Este estudio busca superar las limitaciones asociadas con la descalcificación al aplicar la tinción tricrómica de Goldner con resinas plásticas. Se enfoca en visualizar detalladamente muestras óseas y dentales no descalcificadas en modelos animales. Se emplearon muestras de mandíbula y diente de perro (Canis familiaris), así como tibia de conejo (Oryctolagus cuniculus) con implante dental de titanio y substituto de injerto óseo. Se realizaron ajustes al protocolo original, incluyendo un tratamiento superficial previo a la tinción. La plastinación y la inclusión en resinas plásticas específicas fueron parte del proceso. Las muestras microplastinadas y teñidas mostraron una calidad óptima para microscopía óptica. Las de perro permitieron la observación detallada de la relación diente-tejido periodontal, mientras que las de conejo revelaron una clara diferenciación entre tejido óseo mineralizado y osteoide. La tinción facilitó examinar la interface precisa entre tejidos blandos, injerto óseo e implante. La adaptación exitosa de la tinción tricrómica de Goldner a muestras en resinas plásticas representa un avance significativo en la investigación histológica de tejidos duros. Esta metodología destaca como una herramienta eficaz para evaluar implantes y biomateriales en modelos animales, brindando una visualización detallada sin comprometer la integridad de las muestras. La combinación de histoquímica y resinas plásticas ofrece una alternativa valiosa para estudios microanatómicos, abriendo nuevas posibilidades en la investigación de tejidos duros y evaluación de estructuras óseas.

Proliferation and differentiation of MC3T3-E1 cells on polymethyl methacrylate cements containing Fe3O4 and TiO2 for hyperthermic treatment of metastatic bone tumors.

Polymethyl methacrylate (PMMA) bone cement is widely used to relieve pain caused by metastatic bone tumors. We previously found that PMMA bone cement containing 15 mass% or more of TiO2 showed good apatite-forming ability, and 25 mass% or more of Fe3O4 generated sufficient heat for hyperthermia under an alternating current (AC) magnetic field. In this study, the cytocompatibility of PMMA bone cement with Fe3O4:TiO2 weight ratios of 25:15 (F25T15-3/2-42) and 30:15 (F30T15-3/2-42) was evaluated using osteoblastic cells (MC3T3-E1). The proliferation and differentiation of MC3T3-E1 cells were suppressed for F25T15-3/2-42 and F30T15-3/2-42 compared to PMMA bone cement without Fe3O4 and TiO2 (F0T0-3/2-42). The release of methyl methacrylate (MMA) monomers from F25T15-3/2-42 and F30T15-3/2-42 at 7 days was about 33 and 50 times higher than that from F0T0-3/2-42, respectively. The remarkable release of MMA monomers from F25T15-3/2-42 and F30T15-3/2-42 may be responsible for the suppressed proliferation and differentiation of MC3T3-E1 cells. The release of MMA monomers was not reduced when the MMA/PMMA weight ratio was decreased from 3/2 to 1/1, however, it was significantly reduced by increasing the content of benzoyl peroxide (BPO) and N, N-dimethyl-p-toluidine (DMPT) to 8 and 4 mass% against MMA, respectively. Proliferation and differentiation of MC3T3-E1 cells on PMMA-type cements containing Fe3O4 and TiO2 with increased BPO and DMPT contents need to be investigated in the future; however, our findings will be useful for designing PMMA cements for the hyperthermic treatment of metastatic bone tumors.

Poly-Ether Ether-Ketone Post Conditioned with Sulfuric Acid, Rose Bengal Activated by Photodynamic Therapy and Sandblasting on Pushout Bond Strength to Radicular Dentin Luted with Methyl Methacrylate and Composite-Based Cement.

Objective: Assessment of post surface conditioners [sulfuric acid (SA), Rose Bengal (RB), and sandblasting (SB)] and different luting cements [methyl methacrylate (MMA)-based cement and composite-based cement] on pushout bond strength (PBS) of poly-ether ether-ketone (PEEK) post bonded to canal dentin. Materials and methods: Endodontic treatment was performed on 120 single-rooted human premolar teeth. The preparation of the post space was performed and 4 mm of gutta-percha was retained in the apical region of the root. One hundred and twenty PEEK posts were fabricated from a PEEK blank utilizing a Computer aided design-Computer aided manufacture (CAD-CAM) system. The PEEK posts were allocated randomly into four groups based on post surface conditioning (n = 30). Group A: SA, Group B: RB, Group C: SB, and Group D: No conditioning (NC). Each group was further divided into two subgroups based on the luting cement used for bonding (n = 15). Group A1, B1, C1, and D1 specimens were cemented using composite-based resin cement. However, Group A2, B2, C2, and D2 posts were luted with MMA-based resin cement. PBS assessment using a universal testing machine was performed. Failure modes were analyzed under a stereomicroscope. The data relating to the effects of surface treatment and luting types of cement were analyzed using one-way analysis of variance (ANOVA) and Tukey's post hoc test (p = 0.05). Results: Coronal section of Group B2: RB+Super-Bond C&B [9.61 ± 0.75 megapascals (MPa)] displayed the highest bond scores of PEEK after root dentin. Whereas it was also discovered that Group D1: NC+Panavia®V5 (2.05 ± 0.72 MPa) presented the lowest PBS scores. Intergroup comparison analysis revealed that Group A2: SA+Super-Bond C&B and Group B2: RB+Super-Bond C&B displayed no significant difference in their bond scores. Conclusions: RB and SA possess the potential to be used as a PEEK post conditioner. MMA-based cement displayed better performance than composite-based cement.

Bone Cement Fumes Generated in Laminar Airflow Versus Conventionally Ventilated Operating Rooms: Does the Mixing System Matter?

BACKGROUND: Bone cement is commonly utilized in a variety of orthopaedic procedures and contains methylmethacrylate (MMA) monomer. MMA is a colorless, clear, flammable liquid of intense odor. Its vapor concentration in the immediate breathing zone can vary considerably in the operative setting and, in higher concentrations, can become an occupational health hazard. Therefore, reducing MMA vapor is desirable. The aim of this study was to compare the MMA vapor levels emitted during mixing among 5 commercially available cement-mixing systems across 2 operative settings: an operating room (OR) with conventional ventilation (CV) and an OR with laminar airflow (LAF). METHODS: A prospective, in vitro study was conducted at a single hospital in an OR with LAF and in an OR with CV. MMA vapor release during the cement preparation of a SAWBONES femoral canal was measured with use of a calibrated MiniRAE 3000. A total of 5 different vacuum cement-mixing systems were utilized to mix the same cement type according to the manufacturer instructions of each system. MMA vapor concentrations were measured during 5 phases of mixing, and each mixing system was randomly utilized 10 times in each OR. RESULTS: When comparing the MMA concentration levels of each system between the 2 settings, emissions remained generally higher in the CV setting for every system and in nearly every phase. Among the 5 systems analyzed, System #5, the only entirely closed system, had the lowest overall emissions for each of the 5 phases in the CV setting. CONCLUSIONS: This study demonstrated that an operative environment with LAF is conducive to clearing the fumes of MMA during mixing as well as limiting the amount of time that residual fumes linger after mixing. Additionally, the entirely closed cement-mixing system was the most effective in minimizing fume levels within the CV setting. Utilizing this closed system, especially in an OR with CV, may reduce exposure to MMA fumes from bone cement, potentially creating a more favorable working environment. CLINICAL RELEVANCE: This study provides evidence that a closed cement-mixing system utilized under vacuum in both an OR with CV and an OR with LAF is effective in keeping MMA fume levels below those considered harmful by the U.S. Occupational Safety and Health Administration.

Can we do better at measuring patient-reported outcomes after cranioplasty? A systematic review.

Measuring quality of life (QOL) after cranioplasty is increasingly evident as a necessary component of patient-centered care. For data to be useful in clinical decision-making and approval of new therapies, studies must utilize valid and reliable instruments. Our objective was to critically appraise studies evaluating QOL in adult cranioplasty patients and determine validity and relevance of the patient-reported outcome measures (PROMs) used. Electronic databases of PubMed, Embase, CINAHL, and PsychINFO were used to identify PROMs measuring QOL in adult patients with cranioplasty. The methodological approach, cranioplasty outcomes, and domains measured by the PROMs were extracted and summarized descriptively. A content analysis of the identified PROMs was completed to identify the concepts measured. From 2236 articles identified, 17 articles containing eight QOL PROMs met the inclusion criteria. None of the PROMs was specifically validated or developed for adults undergoing cranioplasty. The QOL domains included physical health, psychological health, social health, and general QOL. These four domains encompassed 216 total items among the PROMs. Appearance was only assessed in two PROMs. To our knowledge, there are currently no validated PROMs that comprehensively measure appearance, facial function, and adverse effects in adults undergoing cranioplasty. There is an urgent need to develop PROMs to measure QOL outcomes rigorously and comprehensively in this patient population to inform clinical care, research, and quality improvement initiatives. Findings from this systematic review will be used to derive an outcome instrument containing important concepts related to QOL in patients who undergo cranioplasty.

Methylmetacrylate (PMMA) cranioplasty technique: Technical interest of intraoperative modeling and review of the literature.

Reconstruction of bone loss in the cranial vault may be necessary for functional or aesthetic reasons following trauma, decompression craniectomy, or craniofacial malformations. Many techniques have been described in the literature, using various materials, each with its own advantages and drawbacks. Reconstruction with polymethylmetacrylate cement has the advantage of a durable result and relative ease of use. In this article we present our cement cranioplasty technique through 4 clinical cases of cranial vault reconstruction, by direct intraoperative modeling on the bone defect. This accessible, effective method, applicable to all sizes of defect, remains an attractive option in the arsenal of techniques available today.

A simple method to improve the antibiotic elution profiles from polymethylmethacrylate bone cement spacers by using rapid absorbable sutures.

OBJECTIVE: Antibiotic-loaded bone cement beads and spacers have been widely used for orthopaedic infection. Poor antibiotic elution is not capable of eradicating microbial pathogens and could lead to treatment failure. The elution profiles differ among different cement formulations. Although Simplex P cement has the least release amount, it is widely used due to its ready availability. Previous methods aiming to improve the elution profiles were not translated well to clinical practice. We sought to address this by using easily available materials to improve the elution profile of antibiotics from PMMA, which allows clinicians to implement the method intraoperatively. METHODS: Vancomycin was mixed with Simplex P cement. We used Vicryl Rapide sutures to fabricate sustained-release cement beads by repetitively passing the sutures through the beads and/or mixing suture segments into the cement formulation. Vancomycin elution was measured for 49 days. The mechanism of antibiotic release was observed with gross appearance and scanning electron microscopic images. The antimicrobial activities against MRSA were tested using an agar disk diffusion bioassay. RESULTS: Passing Vicryl Rapide sutures through cement beads significantly improved the elution profiles in the 7-week period. The increased ratios were 9.0% on the first day and 118.0% from the 2nd day to the 49th day. Addition of suture segments did not increase release amount. The Vicryl Rapide sutures completely degraded at the periphery and partially degraded at the center. The antibiotic particles were released around the suture, while antibiotic particles kept densely entrapped in the control group. The antimicrobial activities were stronger in passing suture groups. CONCLUSION: Passing fast absorbable sutures through PMMA cement is a feasible method to fabricate sustained-release antibiotic bone cement. Intra-cement tunnels can be formed, and the effect can last for at least 7 weeks. It is suitable for a temporary spacer between two stages of a revision surgery.

Electrochemical Investigation of Iron-Catalyzed Atom Transfer Radical Polymerization.

Use of iron-based catalysts in atom transfer radical polymerization (ATRP) is very interesting because of the abundance of the metal and its biocompatibility. Although the mechanism of action is not well understood yet, iron halide salts are usually used as catalysts, often in the presence of nitrogen or phosphorous ligands (L). In this study, electrochemically mediated ATRP (eATRP) of methyl methacrylate (MMA) catalyzed by FeCl3, both in the absence and presence of additional ligands, was investigated in dimethylformamide. The electrochemical behavior of FeCl3 and FeCl3/L was deeply investigated showing the speciation of Fe(III) and Fe(II) and the role played by added ligands. It is shown that amine ligands form stable iron complexes, whereas phosphines act as reducing agents. eATRP of MMA catalyzed by FeCl3 was investigated in different conditions. In particular, the effects of temperature, catalyst concentration, catalyst-to-initiator ratio, halide ion excess and added ligands were investigated. In general, polymerization was moderately fast but difficult to control. Surprisingly, the best results were obtained with FeCl3 without any other ligand. Electrogenerated Fe(II) effectively activates the dormant chains but deactivation of the propagating radicals by Fe(III) species is less efficient, resulting in dispersity > 1.5, unless a high concentration of FeCl3 is used.

Functionalized Fe3O4-based methyl methacrylate Pickering PolyHIPE composites costabilized by fluorinated block copolymer for oil/water separation.

High internal phase emulsion (HIPE) technology has been emerged as a prodigious source to create tailor-made porous structures. This type of emulsion contains significantly higher amount of water in it, which is only possible with special type of stabilizers. Most specifically, the monomers with sufficiently high solubility in water such as methyl methacrylate (MMA) make it more cumbersome to stabilize in the form of HIPE. Here we have reported the combination of stabilizers including fluorinated block copolymer Poly (2-dimethylamino)ethyl methacrylate-b-Poly(trifluoroethyl methacrylate) (PDMAEMA-b-PTFEMA) and humic acid modified iron-oxide (HA-Fe3O4) nanoparticles (NPs) to stabilize HIPE, which resulted in highly porous and interconnected products. Fluorinated block copolymers with inherent hydrophobic nature along with iron oxide nanoparticles increased the water repellency of MMA based polymeric monoliths. Increasing the amount of stabilizer increased the porosity and BET specific surface area to 83.8% and 27 ± 0.8 µm, respectively. The prepared porous materials demonstrated hydrophobic characteristics while adsorbing oil from the surface of water up to 16 g/g. Moreover, the adsorbed oil from the prepared monolith was recovered by using simple centrifugation method without damaging the structure. This research opens new avenues to prepare more useful oil and water separation materials such as membranes, pollutant adsorbers, and so on.

Plant Oil-Based Acrylic Latexes towards Multisubstrate Bonding Adhesives Applications.

To investigate the utility of acrylic monomers from various plant oils in adhesives manufacturing, 25-45 wt. % of high oleic soybean oil-based monomer (HOSBM) was copolymerized in a miniemulsion with commercially applied butyl acrylate (BA), methyl methacrylate (MMA), or styrene (St). The compositions of the resulting ternary latex copolymers were varied in terms of both "soft" (HOSBM, BA) and "rigid" (MMA or St) macromolecular fragments, while total monomer conversion and molecular weight of copolymers were determined after synthesis. For most latexes, results indicated the presence of lower and higher molecular weight fractions, which is beneficial for the material adhesive performance. To correlate surface properties and adhesive performance of HOSBM-based copolymer latexes, contact angle hysteresis (using water as a contact liquid) for each latex-substrate pair was first determined. The data showed that plant oil-based latexes exhibit a clear ability to spread and adhere once applied on the surface of materials differing by polarities, such as semicrystalline polyethylene terephthalate (PET), polypropylene (PP), bleached paperboard (uncoated), and tops coated with a clay mineral paperboard. The effectiveness of plant oil-based ternary latexes as adhesives was demonstrated on PET to PP and coated to uncoated paperboard substrates. As a result, the latexes with high biobased content developed in this study provide promising adhesive performance, causing substrate failure instead of cohesive/adhesive break in many experiments.

Magnetically recoverable poly (methyl methacrylate-acrylic acid)/iron oxide magnetic composites nanomaterials with hydrophilic wettability for efficient oil-water separation.

Due to the environmental and production problems of emulsion, it is important to efficiently separate oil-water emulsion to meet the refinery requirement and clean up oil spills. Synthesis of a universal demulsifier is not an easy task because the physical properties of crude oil vary, which makes its characterization and demulsification procedure difficult. To overcome this problem, hydrophilic and magnetically recoverable poly (methyl methacrylate-acrylic acid)/iron oxide magnetic composite nanoparticles ((P(MMA-AA)/Fe3O4 NPs) were developed as an efficient and economical demulsifier via soap-free emulsion polymerization. To characterize the magnetic composite NPs for their appropriate surface morphology and magnetic domain, TEM, FTIR, VSM, and TGA analyses were carried out. The newly synthesized NPs displayed good hydrophilic properties as they migrated quickly to the aqueous emulsion phase, which was also reassured by their water contact angle of 75°. They exhibit strong magnetic characteristics (20 amu/g) in the oil-water emulsion, makings the hydrophilic wettability capable and attractive to the external magnet. Experimental results revealed that the prepared magnetic composite NPs separated 99% of the water from stable emulsion in 30 min and could be recycled 8 times through magnetic separation. The recycled magnetic composite NPs maintain their hydrophilic wettability and efficiency in separating oil-water emulsion, making them economical and commercially viable. The migration of magnetic composite NPs to the aqueous phase in the stable emulsion with a strong magnetic domain explains the coalescence of emulsified water droplets and their quick separation from the stable emulsions through the external magnet.

The Comparison of Autologous Bone, Methyl-Methacrylate, Porous Polyethylene, and Titanium Mesh in Cranioplasty.

AIM: To discuss four different materials that are frequently used in cranioplasty, and to reveal their advantages and disadvantages. MATERIAL AND METHODS: We retrospectively reviewed 85 of our cranioplasty surgeries between 2016 and 2019. Reconstruction surgeries were excluded from our study due to craniofacial trauma. RESULTS: Of the materials used in cranioplasty, 33 are autologous bone, 32 are methyl-methacrylate, 12 are porous polyethylene, and 8 are titanium mesh. Complications developed in 16 patients. Of these, 10 are infection, 3 are flap collapse, 2 are wound healing disorders, and 1 is reactive effusion complications due to the used material. The highest complication rate was 21.9% in cranioplasty with methyl-methacrylate. No major complications were observed in cranioplasty with titanium mesh. CONCLUSION: Cranioplasty, which are among the surgeries with high complications in neurosurgery, maintain their importance today. As technology is developed and cost problems are resolved, cranioplasty takes its place among the safer and standard neurosurgical operations.

Manubrium Reconstruction.

To date, there is no standard approach for manubrial reconstruction. We had previously utilized mesh; however, this resulted in breakage, infection, and poor cosmesis. In this case series, we describe our transition to iliac wing autograft reconstruction. We examined 7 patients who underwent manubrial resection and reconstruction: 2 with mesh and methyl methacrylate and 5 with an iliac wing autograft. The outcomes of the autograft patients were overall favorable with no short-term complications or instances of breakage. We conclude that an iliac wing autograft for manubrial reconstruction is feasible and effective alternative to methyl methacrylate mesh.

Preparation and characterization of a water-resistant polyamide-oxidized starch-methyl methacrylate eco-friendly wood adhesive.

A water-resistant polyamide-oxidized starch-methyl methacrylate (P-OS-M) adhesive with zero formaldehyde-emission was successfully synthesized, using natural corn starch, KMnO4, polyamide and methyl methacrylate as raw material, oxidant, crosslinking agent and comonomer, respectively. The P-OS-M25 adhesive synthesized with the optimal amount of methyl methacrylate (25 ml) could reach wet shear strength of 1.04 MPa, which was far greater than natural starch (NS) and oxidized starch (OS). Fourier transforms infrared spectrometer (FTIR) and X-ray diffraction (XRD) results showed that polyamide and methyl methacrylate were successfully cross-linked and copolymerized with oxidized starch. In addition, thermogravimetric analysis (TGA), rheology, scanning electron microscope (SEM) and contact angle respectively indicated that P-OS-M adhesive was suitable for wood adhesives in terms of thermal stability, viscosity, morphological and water resistence. These advantages increased the possibility of P-OS-M adhesive instead of petroleum-based wood adhesives.

Chest Wall Reconstruction Using 3-Dimensional Printing: Functional and Mechanical Results.

BACKGROUND: Tumors involving the chest wall may require extensive resection and reconstruction. This study aims to evaluate functional, cosmetic results, and quality of life (QoL) in patients who had a reconstruction based on patient-specific 3-dimensional (3D) printing. METHODS: The patient-specific chest wall prosthesis was created for 10 patients. The anatomical models were 3D printed and used to produce a silicone mold that was filled with methyl methacrylate to create the customized prosthesis. Evaluation of the reconstruction was completed with a QoL assessment and postoperative tracking of patients' chest motion, using infrared markers. The distance between plot points representing markers on the operated and contralateral sides was measured to assess symmetrical motion. RESULTS: Twenty-three consecutive patients were enrolled, with the median age of 64 years. Thirteen patients underwent a nonrigid reconstruction, and 10 had a patient-specific rigid reconstruction with methyl methacrylate. The median number of ribs resected was 3. No postoperative complications or morbidity related to the prostheses were reported. The median hospital stay in the nonrigid reconstruction group was 8.5 days compared with 7.5 days (p = .167) in the rigid reconstruction group. Postoperatively, most patients had low levels of symptoms, with 82% experiencing chest pain and 53% experiencing dyspnea. Rigid reconstruction patients demonstrated more symmetrical breathing motion compared with nonrigid reconstruction patients. The mean distances were 2.32 ± 2.18 and 7.28 ± 5.87 (P < .00001), respectively. CONCLUSIONS: This study shows that a 3D patient-specific prosthesis is feasible and safe, suggesting a possible trend toward improved breathing mechanics, QoL, and cosmetic results.

Probing the role of methyl methacrylate release from spacer materials in induced membrane bone healing.

In the induced membrane (IM) technique for bone reconstruction, a poly(methyl methacrylate) (PMMA) spacer is implanted to induce formation of a foreign body membrane around the defect site. Membrane development is essential for later bone grafting success, yet the mechanism by which the IM promotes bone regeneration remains unknown, as are the ways that spacer composition plays a role in the membrane's healing potential. This study investigated the impact of leached methyl methacrylate (MMA)-the major monomeric component of PMMA-on IM development. In vitro cell culture found that MMA elution did not impact endothelial cell or mesenchymal stem cell proliferation. For in vivo analysis, we advanced a streamlined rat femoral model to efficiently study the influence of spacer properties on IM characteristics. Comparison of membrane formation around polycaprolactone (PCL), MMA-eluting PCL (high-dose PCL-MMA and low-dose PCL-MMA), and surgical PMMA revealed robust membranes enveloped all groups after 4 weeks in vivo, with elevated expression of osteogenic bone morphogenetic protein-2 and angiogenic vascular endothelial growth factor compared with the surrounding muscle and bone tissues. Growth factor quantitation in IM tissue found no statistically significant difference between groups. New bone growth, vascularization, and CD163+ macrophage populations surrounding the polymer implants were also quantified; and blood vessel formation around high-dose PCL-MMA was found to be significantly decreased compared with PCL alone. To the best of our knowledge, these findings represent the first time that results have been obtained about the characteristics of membranes formed around PCL in the IM setting.

Adhesión a dentina parte I: características del sustrato y sistemas adhesivos / Dentin bonding part I: substrate characteristics and bonding systems

La Odontología Restauradora contemporánea no puede concebirse sin la adhesión de los materiales restauradores a las estructuras dentarias. En mu-chos procedimientos restauradores, no sólo el esmal-te sino también la dentina se encuentra involucrada, por lo tanto, la adhesión a esta última juega un rol cla-ve en el éxito clínico. No obstante, todavía supone un gran desafío lograr una adhesión estable y predeci-ble en el tiempo. El propósito del presente artículo es analizar las características principales de la dentina como sustrato adhesivo y describir los sistemas ad-hesivos actuales y sus mecanismos de acción (AU)

Contemporary Restorative Dentistry cannot be conceived without the adhesion of restorative materials to dental structures. In many restorative procedures not only the enamel, but also the dentin is involved, therefore dentin bonding plays a key role in their success. However, it is still a great challenge to achieve stable and predictable dentin bonding over time. The aim of this article is to analyze the main characteristics of dentin as an adhesive substrate and to describe current adhesive systems and their bonding mechanisms (AU)

Effect of processing methods on the cytotoxicity of methyl methacrylate-based ocular prostheses: An in vitro study.

The study evaluated the influence of cycles and methods of an ocular prosthesis resin on cytotoxicity toward human conjunctival cells. Resins were polymerized by water bath (WB, 74 °C or 100 °C for 30 min to 9 h), microwave (MW, 1200 W, 3 to 14 min and 30 s at 0 to 720 W), or autopolymerization (AP, room temperature for 20 min ± 60 °C for 30 min). Degree of conversion (DC), cytotoxicity, level of inflammatory mediators, gene expression of different markers, and apoptosis were evaluated. Data were submitted to ANOVA and Tukey test (p < 0.05). WB with longer processing time at higher temperature had highest DC (85.6%) and higher TGF ß1-gene expression (1.39); long cycle low power MW showed lowest DC (69.6%), lower cell proliferation (85.4%, MTT), and large IL-2 release (39,297 ng/mL). AP with additional processing time showed lower cell proliferation (75.3%, Alamar Blue), and AP polymerized at room temperature showed higher CASP 9-gene expression (1.21). AP methods showed higher IL-6 release (>277 pg/mL). Short cycle medium power MW had higher IL-23 release (534.2 pg/mL). MW (long and short cycles) and AP polymerizations have triggered a more intense inflammatory response. Among methods recommended by the manufacturer, WB showed high DC and less cytotoxicity.

Nickel, chromium and methyl methacrylate monomer release from orthopaedic functional appliances.

AIM: This study was purposed to evaluate release of nickel and chromium ions and methyl methacrylate (MMA) monomers from functional appliances and their possible health effects. MATERIALS AND METHODS: Study design: Twin-block appliances and Bionators were immersed in artificial saliva and kept in a thermal incubator. Control group was established as artificial saliva without appliances. Artificial saliva was analysed after 7 days, 30 days and 90 days. Inductively coupled plasma mass spectrometry and gas chromatography-mass spectrometry was used for detection of nickel and chromium ions and MMA monomers. MTT assays and cytokine array were performed. STATISTICS: One way ANOVA with Tukey test and Dunnett's T3 for post-hoc analysis was used for evaluation of time-dependent changes and independent t-test was used for evaluation of MTT assay results. RESULTS: The results revealed that metal ions and MMA monomers are released from the appliances. Metal ion detection pattern was irregular and could not be analysed. Twin-block group showed significantly larger amount of MMA release. MTT assay revealed statistically significant but minimally reduced cellular activity on Bionator and twin-block groups compared to control groups. Cytokine array showed no or less inflammatory cytokine release on Bionator and twin-block groups. CONCLUSION: MMA monomer release was confirmed but the cytotoxic effect of functional appliance material release is minimal or negligible. General toxicity of the functional appliance from the MMA monomer release is likely to be minimal or negligible.