Improving standard volar plate fixation in 3D-guided corrective osteotomy of the distal radius: evaluation of a shim instrument.

Standard volar plates often do not fit the surface of the malunited distal radius after osteotomy, necessitating an offset angle for accurate volar tilt correction. The correction can be achieved if the plate is held at the correct angle when the distal screws are locked. With the advantage of 3D surgical planning and patient-specific instruments, we developed a shim instrument to assist the surgeon in securing the plate at the intended angle when locking the distal screws, and evaluated radiological results. Five female patients aged 63-74 with dorsally angulated extra-articular malunions underwent surgery using 3D-printed guides and the shim instrument. The plate position, drilling guide alignment, screw placements, and distal radius correction on postoperative CTs were compared with the surgical plans. Errors were measured using an anatomical coordinate system, and standard 2D radiographic measures were extracted. Preoperative dorsal tilt ranged from 16° to 35°, and postoperative volar tilt from 1° to 11°. 3D analysis revealed mean absolute correction errors of 6.1° in volar tilt, 1.6° in radial inclination, and 0.6 mm in ulnar variance. The volar tilt error due to the shim instrument, indicated by the mean angle error of the distal screws to the plate, was 2.1° but varied across the five patients. Settling of the distal radius, due to tension during and after reduction, further contributed to a mean loss of 3.5° in volar tilt. The shim instrument helped with securing plates at the intended angle; however, further correction improvements should consider the tension between the fragments of osteoporotic bone.

Simultaneous medial closing wedge distal femoral varus osteotomy and double-bundle anterior cruciate ligament reconstruction in the symptomatic femoral valgus deformity: A case report.

Distal femoral varus osteotomy (DFVO) is a widely recognized surgical procedure used to address valgus malalignment in patients with knee joint disorders. However, it still remains unclear whether anterior cruciate ligament (ACL) reconstruction can be performed in a single procedure along with DFVO. Herein, we present a 73-year-old female patient who developed lateral osteoarthritis of the knee with valgus alignment due to chronic ACL deficiency following a twisting injury during skiing. She was physiologically very active, and strongly demanded to return to sports. We performed a combined procedure involving a medial closing wedge DFVO using an anatomical locking plate, along with double-bundle ACL reconstruction. The postoperative radiograph confirmed successful correction of knee alignment, specifically achieving varus alignment with precise conformance of the anatomical plate to the medial contour of the distal femur following the osteotomy. The patient resumed her previous sports activities without experiencing knee pain. The operated knee demonstrated restored anterior stability, as indicated by negative Lachman test results, and regained full range of motion. Both the Knee Injury and Osteoarthritis Outcome Score and the 2011 Knee Society score demonstrated continuous postoperative improvements over the three-year follow-up period, indicating positive functional outcomes and joint preservation. To the best of our knowledge, this is the first case of medial closing wedge DFVO with anatomic double-bundle ACL reconstruction in the symptomatic femoral valgus deformity with chronic ACL deficiency in the literature.

A rare complication of tension band fixation of olecranon osteotomy: Distal migration of K-wire.

Tension band wiring (TBW) is one of the most commonly used fixation techniques to fix olecranon osteotomies. Hardware prominence has been the most commonly reported complication of TBW. However, distal migration of Kirschner (K)-wire after TBW fixation for olecranon osteotomy has not been reported. In this case report, we presented distal migration of K-wire detected nine months after initial surgery in a 46-year-old male patient. The patient was operated on for an intraarticular distal humerus fracture using an olecranon osteotomy. The osteotomy was fixed with TBW fixation. The patient missed routine follow-ups and presented to the outpatient clinic with a complaint of skin irritation at the elbow nine months after the surgery. On radiological examination, distal migration of one K-wire was detected. The K-wire was surgically removed without any complication. Physicians should be aware of possible complications of TBW and remove fixation after fracture union to avoid unexpected complications.

Electromyographic biofeedback training in a cerebral palsy patient undergoing pronator teres rerouting and brachioradialis to extensor carpi radialis brevis tendon transfer surgery: A case report.

Several surgical procedures are used to treat dynamic pronation position of the forearm and flexion deformity of the wrist in cerebral palsy. Postoperative results of pronator teres rerouting were explored, while specially designed postoperative physiotherapy and its outcomes were limited. Herein, we present a case in whom the outcomes of electromyographic biofeedback (EMG-BF) training were assessed after pronator teres rerouting and brachioradialis tendon to extensor carpi radialis brevis tendon transfer combined with derotation osteotomy. The peak value increased, while the resting value decreased for the muscles after the intervention. Range of motion, hand function, manual ability, functional independence, and quality of life levels were improved. In conclusion, EMG biofeedback training may have a positive effect on neuromuscular control of pronator teres and brachioradialis. Free use of the upper extremity and improved manual ability positively affect the activity and quality of life of the patients.

Total knee arthroplasty following lateral closing-wedge high tibial osteotomy versus primary total knee arthroplasty: a propensity score matching study.

BACKGROUND: The disparity in patient-reported outcomes between total knee arthroplasty (TKA) following high tibial osteotomy (HTO) and primary TKA has yet to be fully comprehended. This study aims to compare the patient-reported outcomes, radiological parameters and complication rates between TKA following HTO and primary TKA. METHODS: Sixty-five patients who underwent TKA following lateral closing-wedge HTO were compared to a matched group of primary TKA at postoperative 6-months and 1-year. Between-group confounders of age, gender, smoking status, Body Mass index, preoperative Numeric Rating Scale (NRS) pain in rest, Knee injury and Osteoarthritis Outcome Score-Physical function Shortform (KOOS-PS), EuroQol five-dimensional (EQ-5D) overall health score, and Oxford Knee Score (OKS) were balanced by propensity score matching. Patient-reported outcome measures were NRS pain in rest, KOOS-PS, EQ-5D overall health score, and OKS. Radiological parameters were femorotibial angle, medial proximal tibial angle, anatomical lateral distal femoral angle, posterior tibial slope, and patellar height assessed by Insall-Salvati ratio. The complication rates of TKA were compared between the two groups. The HTO survival time, the choice of staple removal before or during TKA in patients who underwent TKA following HTO patients, and the rate of patellar resurfacing were assessed. The p value < 0.0125 indicates statistical significance after Bonferroni correction. RESULTS: After propensity score matching, no significant between-group differences in the patient-reported outcome measures, radiographical parameters and complication rates were found (p > 0.0125). In the TKA following HTO group, with an average HTO survival time of 8.7 years, staples were removed before TKA in 46 patients (71%) and during TKA in 19 patients, and 11 cases (17%) had patella resurfacing. In the primary TKA group, 15 cases (23%) had patella resurfacing. CONCLUSION: The short-term assessment of TKA following HTO indicates outcomes similar to primary TKA. A previous HTO does not impact the early results of subsequent TKA, suggesting that the previous HTO has minimal influence on TKA outcomes. LEVEL OF EVIDENCE: III, cohort study.

[Evaluation of the efficacy of medial open wedge high tibial osteotomy combined with anterior cruciate ligament reconstruction in the treatment of varus knee osteoarthritis with anterior cruciate ligament injury].

Objective: To evaluate the efficacy of medial open wedge high tibial osteotomy (MOWHTO) combined with anterior cruciate ligament (ACL) reconstruction in the treatment of varus knee osteoarthritis (OA) with ACL injury. Methods: A follow-up study. The study retrospectively analyzed the patients underwent MOWHTO combined with ACL reconstruction for treatment of varus knee OA with ACL injury in Tianjin Hospital between April 2018 and September 2022. The preoperative and postoperative posterior slope angle (PSA), hip-knee-ankle angle (HKA), visual analog scale (VAS) pain scores, Lysholm score, International Knee Documentation Committee (IKDC) score, Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC) score, and Tegner score were compared. The follow-up indicators were recorded at 6 weeks, 3 months and 1 year after operation, and the complications were recorded. Results: The study included 32 patients (23 males, 9 females) with a mean age of (50.7±8.4) years. The mean follow-up time was (21.2±4.8) months. PSA increased from 9.2°±1.8° preoperatively to 11.1°±2.4° postoperatively, and HKA increased from 168.7°±2.2° to 181.5°±2.2° (both P<0.01). The indicators such as VAS score (6.8±1.1 vs 1.8±0.4), Lysholm score (52.6±7.1 vs 82.0±6.4), IKDC score (64.7±6.2 vs 80.3±10.0), WOMAC score (51.8±6.3 vs 81.8±6.5), and Tegner score (1.9±0.6 vs 5.0±1.0) were all improved after the operation (all P<0.01). Complications occurred in 5 patients (15.6%), including hematomas, sensory abnormalities, intermuscular vein thrombosis and correction angle loss. Conclusion: MOWHTO combined with ACL reconstruction is a safe and effective approach for the treatment of varus knee OA with ACL injury.

Precise execution of personalized surgical planning using three-dimensional printed guide template in severe and complex adult spinal deformity patients requiring three-column osteotomy: a retrospective, comparative matched-cohort study.

BACKGROUND: The surgical treatment of severe and complex adult spinal deformity (ASD) commonly required three-column osteotomy (3-CO), which was technically demanding with high risk of neurological deficit. Personalized three dimensional (3D)-printed guide template based on preoperative planning has been gradually applied in 3-CO procedure. The purpose of this study was to compare the efficacy, safety, and precision of 3D-printed osteotomy guide template and free-hand technique in the treatment of severe and complex ASD patients requiring 3-CO. METHODS: This was a single-centre retrospective comparative cohort study of patients with severe and complex ASD (Cobb angle of scoliosis > 80° with flexibility < 25% or focal kyphosis > 90°) who underwent posterior spinal fusion and 3-CO between January 2020 to January 2023, with a minimum 12 months follow-up. Personalized computer-assisted three-dimensional osteotomy simulation was performed for all recruited patients, who were further divided into template and non-template groups based on the application of 3D-printed osteotomy guide template according to the surgical planning. Patients in the two groups were age- and gender- propensity-matched. The radiographic parameters, postoperative neurological deficit, and precision of osteotomy execution were compared between groups. RESULTS: A total of 40 patients (age 36.53 ± 11.98 years) were retrospectively recruited, with 20 patients in each group. The preoperative focal kyphosis (FK) was 92.72° ± 36.77° in the template group and 93.47° ± 33.91° in the non-template group, with a main curve Cobb angle of 63.35° (15.00°, 92.25°) and 64.00° (20.25°, 99.20°), respectively. Following the correction surgery, there were no significant differences in postoperative FK, postoperative main curve Cobb angle, correction rate of FK (54.20% vs. 51.94%, P = 0.738), and correction rate of main curve Cobb angle (72.41% vs. 61.33%, P = 0.101) between the groups. However, the match ratio of execution to simulation osteotomy angle was significantly greater in the template group than the non-template group (coronal: 89.90% vs. 74.50%, P < 0.001; sagittal: 90.45% vs. 80.35%, P < 0.001). The operating time (ORT) was significantly shorter (359.25 ± 57.79 min vs. 398.90 ± 59.48 min, P = 0.039) and the incidence of postoperative neurological deficit (5.0% vs. 35.0%, P = 0.018) was significantly lower in the template group than the non-template group. CONCLUSION: Performing 3-CO with the assistance of personalized 3D-printed guide template could increase the precision of execution, decrease the risk of postoperative neurological deficit, and shorten the ORT in the correction surgery for severe and complex ASD. The personalized osteotomy guide had the advantages of 3D insight of the case-specific anatomy, identification of osteotomy location, and translation of the surgical planning or simulation to the real surgical site.

Surgical Correction of Ischiopagus Tripus Conjoined Twins with Fused Pelvis: Enhancing Quality of Life through Orthopedic Intervention.

BACKGROUND The rarity of ischiopagus tripus conjoined twins complicates the surgical separation, owing to the lack of cases and high complexity. We aim to report our experience in performing orthopedic correction for ischiopagus tripus twins. CASE REPORT A pair of 3-year-old conjoined boys presented with a fused body at the pelvis region and only 1 umbilicus. There were 2 legs separated by shared genitalia and an anus at the midline, and 1 fused leg, which could be felt and moved by both of the patients. The twins also shared internal organs of the bladder, intestine, and rectum, as visualized through angiography computerized tomography scan. After several team discussions with the institutional review board, the hospital ethics committee, and both parents, it was agreed to perform disarticulation of the fused third limb, followed by correction of the trunk alignment by pelvic closed wedge osteotomy and internal fixation. We successfully reconstructed the pelvis using locking plates and additional 3.5-mm cortical screws and 1.2-mm stainless steel wire. CONCLUSIONS This report describes the presentation and surgical management of a case of ischiopagus tripus conjoined twins. It highlights the challenges involved in surgery and the importance of investigating these infants for other congenital abnormalities. Although surgical approaches for different sets of twins should be individually tailored, interventions aimed to provide optimal outcomes should consider ethical issues and parental/patient expectations. Even in situations in which the twins are inseparable, there is still room for surgical correction to be performed.

3D-Printed custom-made hemipelvic endoprosthetic reconstruction following periacetabular tumor resection: utilizing a novel classification system.

BACKGROUND: Customized 3D-printed pelvic implants with a porous structure have revolutionized periacetabular pelvic defect reconstruction after tumor resection, offering improved osteointegration, long-term stability, and anatomical fit. However, the lack of an established classification system hampers implementation and progress. METHODS: We formulated a novel classification system based on pelvic defect morphology and 3D-printed hemipelvis endoprostheses. It integrates surgical approach, osteotomy guide plate and prosthesis design, postoperative rehabilitation plans, and perioperative processes. RESULTS: Retrospectively analyzing 60 patients (31 males, 29 females), we classified them into Type A (15 patients: Aa = 6, Ab = 9), Type B (27 patients: Ba = 15, Bb = 12), Type C (17 patients). All underwent customized osteotomy guide plate-assisted tumor resection and 3D-printed hemipelvic endoprosthesis reconstruction. Follow-up duration was median 36.5 ± 15.0 months (range, 6 to 74 months). The mean operating time was 430.0 ± 106.7 min, intraoperative blood loss 2018.3 ± 1305.6 ml, transfusion volume 2510.0 ± 1778.1 ml. Complications occurred in 13 patients (21.7%), including poor wound healing (10.0%), deep prosthesis infection (6.7%), hip dislocation (3.3%), screw fracture (1.7%), and interface loosening (1.7%). VAS score improved from 5.5 ± 1.4 to 1.7 ± 1.3, MSTS-93 score from 14.8 ± 2.5 to 23.0 ± 5.6. Implant osseointegration success rate was 98.5% (128/130), with one Type Ba patient experiencing distal prosthesis loosening. CONCLUSION: The West China classification may supplement the Enneking and Dunham classification, enhancing interdisciplinary communication and surgical outcomes. However, further validation and wider adoption are required to confirm clinical effectiveness.

Transiliac-Shortening Osteotomy to Treat Ischial Pressure Injury due to Fixed Pelvic Obliquity: A Case Report.

CASE: A 17-year-old adolescent boy with Gross Motor Function Classification System 5 cerebral palsy and neuromuscular scoliosis underwent posterior spinal fusion and segmental spinal instrumentation from T3 to the pelvis. He developed a right ischial pressure injury a few months postoperatively, which persisted despite nonoperative measures. He subsequently underwent an ipsilateral transiliac-shortening osteotomy 16 months after spinal surgery to treat his residual pelvic obliquity and the ischial pressure injury, which healed completely. At the 1-year follow-up visit, there were no further signs of pressure injury. CONCLUSION: This case report describes transiliac-shortening osteotomy as a viable treatment option for non-healing ischial pressure injuries secondary to fixed pelvic obliquity.

Finite element analysis of the effect of tibial osteotomy on the stress of polyethylene liner in total knee arthroplasty.

AIM: To explore the effects of tibial osteotomy varus angle combined with posterior tibial slope (PTS) on the stress of polyethylene liner in total knee arthroplasty (TKA) by building finite element model (FEM). METHODS: Established the FEM of standard TKA with tibial osteotomy varus angle 0° to 9° were established and divided into 10 groups. Next, each group was created 10 FEMs with 0° to 9° PTS separately. Calculated the stress on polyethylene liner in each group in Abaqus. Finally, the relevancy between tibial osteotomy angle and polyethylene liner stress was statistically analyzed using multiple regression analysis. RESULTS: As the varus angle increased, the area of maximum stress gradually shifted medially on the polyethylene liner. As the PTS increases, the percentage of surface contact forces on the medial and lateral compartmental of the polyethylene liner gradually converge to the same. When the varus angle is between 0° and 3°, the maximum stress of the medial compartmental surfaces of polyethylene liner rises smoothly with the increase of the PTS. When the varus angle is between 4° and 9°, as the increase of the PTS, the maximum stress of polyethylene liner rises first and then falls, forming a trough at PTS 5° and then rises again. Compared to the PTS, the varus angle has a large effect on the maximum stress of the polyethylene liner (p < .001). CONCLUSION: When the varus angle is 0° to 3°, PTS 0° is recommended, which will result in a more equalized stress distribution of the polyethylene liner in TKA.

The incidence of subsequent hip arthroscopy after rectus-sparing periacetabular osteotomy.

Aims: Periacetabular osteotomy (PAO) is the preferred treatment for symptomatic acetabular dysplasia in adolescents and young adults. There remains a lack of consensus regarding whether intra-articular procedures such as labral repair or improvement of femoral offset should be performed at the time of PAO or addressed subsequent to PAO if symptoms warrant. The purpose was to determine the rate of subsequent hip arthroscopy (HA) in a contemporary cohort of patients, who underwent PAO in isolation without any intra-articular procedures. Methods: From June 2012 to March 2022, 349 rectus-sparing PAOs were performed and followed for a minimum of one year (mean 6.2 years (1 to 11)). The mean age was 24 years (14 to 46) and 88.8% were female (n = 310). Patients were evaluated at final follow-up for patient-reported outcome measures (PROMs). Clinical records were reviewed for complications or subsequent surgery. Radiographs were reviewed for the following acetabular parameters: lateral centre-edge angle, anterior centre-edge angle, acetabular index, and the alpha-angle (AA). Patients were cross-referenced from the two largest hospital systems in our area to determine if subsequent HA was performed. Descriptive statistics were used to analyze risk factors for HA. Results: A total of 16 hips (15 patients; 4.6%) underwent subsequent HA with labral repair and femoral osteochondroplasty, the most common interventions. For those with a minimum of two years of follow-up, 5.3% (n = 14) underwent subsequent HA. No hips underwent total hip arthroplasty and one revision PAO was performed. Overall, 17 hips (4.9%) experienced a complication and 99 (26.9%) underwent hardware removal. All PROMs improved significantly postoperatively. Radiologically, 80% of hips (n = 279) reached the goal for acetabular correction (77% for acetbular index and 93% for LCEA), with no significant differences between those who underwent subsequent HA and those who did not. Conclusion: Rectus-sparing PAO is associated with a low rate of subsequent HA for intra-articular pathology at a mean of 6.2 years' follow-up (1 to 11). Acetabular correction alone may be sufficient as the primary intervention for the majority of patients with symptomatic acetabular dysplasia.

Accuracy of flapless surgery using an autonomous robotic system in full-arch immediate implant restoration: A case series.

OBJECTIVES: This observational study aimed to evaluate the accuracy of robotic computer-assisted implant surgery (r-CAIS) for full-arch immediate restoration and to analyse possible factors contributing to deviations. METHODS: Three edentulous patients (five arches) underwent r-CAIS. Osteotomies were performed using an autonomous robot under the surgeon's supervision, and implant placement was performed in a freehand or robotic manner. Prefabricated provisional prostheses were delivered immediately after surgery. Postoperative cone beam computed tomography scans were performed to assess the deviations between the planned and placed implants. Statistics were compared with deviations of s-CAIS outlined in a meta-analysis. RESULTS: A sum of 28 implants were used. The mean global coronal and apical deviations measured 0.91 ± 0.43 mm and 1.01 ± 0.45 mm, respectively, and the mean angular deviation measured 1.21 ± 1.24 º. The r-CAIS showed significantly better precision than the s-CAIS in full-arch cases (P < 0.001). The implants inserted using the robotic arm exhibited fewer deviations than those placed in the freehand manner. Eighty percent of prefabricated provisional prostheses were successfully delivered. CONCLUSIONS: Within the limitations of the present study, our data suggest that autonomous r-CAIS is a feasible approach for simultaneous immediate restoration in edentulous patients, showing better accuracy than s-CAIS. Further large-scale studies are necessary to verify the advantages and disadvantages of this novel technique and to explore possible factors that influence its accuracy. CLINICAL SIGNIFICANCE: Autonomous r-CAIS can provide clinically acceptable implant placement accuracy in edentulous patients, significantly surpassing s-CAIS. This level of accuracy may represent a viable therapeutic approach for simultaneous immediate full-arch restoration.

Outcomes of Ulnar Shortening Osteotomy with an Intramedullary Bone Graft for Idiopathic Ulnar Impaction Syndrome.

Background: Although several techniques for the treatment of ulnar impaction syndrome (UIS) have been introduced, there have still been reports on various complications such as delayed union, nonunion, refracture, wrist pain, plate irritation, and chronic regional pain syndrome. This study aimed to compare the differences in radiological and clinical outcomes of patients in which intramedullary bone grafting was performed in addition to plate stabilization with those without additional bone grafting during ulnar shortening osteotomies (USOs). Methods: Between November 2014 and June 2021, 53 wrists of 50 patients with idiopathic UIS were retrospectively reviewed. Patients were divided into 2 groups according to whether intramedullary bone grafting was performed. Among the 53 wrists, USO with an intramedullary bone graft was performed in 21 wrists and USO without an intramedullary bone graft was performed in 32 wrists. Demographic data and factors potentially associated with bone union time were analyzed. Results: There was no significant difference between the 2 groups when comparing postoperative radioulnar distance, postoperative ulnar variance, amount of ulnar shortening, and postoperative Disabilities of the Arm, Shoulder and Hand score. Compared to the without-intramedullary bone graft group, bone union time of the osteotomy site was significantly shortened, from 8.8 ± 3.0 weeks to 6.7 ± 1.3 weeks in the with-intramedullary bone graft group. Moreover, there were no cases of nonunion or plate-induced symptoms. Both in univariable and multivariable analyses, intramedullary bone grafting was associated with shorter bone union time. Conclusions: USO with an intramedullary bone graft for idiopathic UIS has favorable radiological and clinical outcomes. The advantage of this technique is the significant shortening of bone union time.

Medial patellar ligament reconstruction in combination with derotational distal femoral osteotomy for treating recurrent patellar dislocation in the presence of increased femoral anteversion: a systematic review.

BACKGROUND: Medial patellar ligament reconstruction (MPFL-R) in combination with derotational distal femoral osteotomy (DDFO) for treating recurrent patellar dislocation (RPD) in the presence of increased femoral anteversion is one of the most commonly used surgical techniques in the current clinical practice. However, there are limited studies on the clinical outcomes of MPFL-R in combination with DDFO to treat RPD in the presence of increased femoral anteversion. PURPOSE: To study the role of MPFL-R in combination with DDFO in the treatment of RPD in the presence of increased femoral anteversion. METHODS: A systematic review was performed according to the PRISMA guidelines by searching the Medline, Embase, Web of Science, and Cochrane Library databases through June 1, 2023. Studies of patients who received MPFL-R in combination with DDFO after presenting with RPD and increased femoral anteversion were included. Methodological quality was assessed using the MINORS (Methodological Index for Nonrandomized Studies) score. Each study's basic characteristics, including characteristic information, radiological parameters, surgical techniques, patient-reported outcomes, and complications, were recorded and analyzed. RESULTS: A total of 6 studies with 231 patients (236 knees) were included. Sample sizes ranged from 12 to 162 patients, and the majority of the patients were female (range, 67-100%). The mean age and follow-up ranges were 18 to 24 years and 16 to 49 months, respectively. The mean femoral anteversion decreased significantly from 34° preoperatively to 12° postoperatively. In studies reporting preoperative and postoperative outcomes, significant improvements were found in the Lysholm score, Kujala score, International Knee Documentation Committee score, and visual analog scale for pain. Postoperative complications were reported in all studies, with an overall reported complication rate of 4.7%, but no redislocations occurred during the follow-up period. CONCLUSION: For RPD with increased femoral anteversion, MPFL-R in combination with DDFO leads to a good clinical outcome and a low redislocation rate. However, there was no consensus among researchers on the indications for MPFL-R combined with DDFO in the treatment of RPD.

Alternative Treatment of Gonarthrosis: Proximal Fibular Osteotomy.

INTRODUCTION: Gonarthrosis is arthrosis of the knee joint, a chronic non-inflammatory disease manifested by progressive destruction of the intra-articular cartilage, accompanied by abnormal formation of the bones form the joint, changes in the synovial membrane and synovial fluid. Gonarthrosis is the most common type of arthrosis. Gonarthrosis can be treated conservatively and operatively. Among well-established surgical options for the treatment of medial gonarthrosis are high tibial osteotomy (HTO), unicompart-mental knee arthroplasty (UKA), and total knee arthroplasty (TKA). Proximal fibular osteotomy (PFO) or superior partial fibulectomy is a relatively recent procedure proposed to reduce knee pain in patients with medial compartment. AIM: Our study aims to demonstrate an alternative treatment for gonarthrosis with proximal fibular osteotomy and reduced knee pain in patients with medial compartment osteoarthritis of the knee. MATERIALS AND METHODS: At the Department of Orthopedics and Traumatology at J.Z.U "Borka Taleski" Prilep in the period from 2018 to 2021, 14 cases were treated, of which 11 were female and 3 were male. All patients were aged between 62 and 82 years with a mean age of 71.3 years. Patients had a severe degree of gonarthrosis (III/IV) according to Kellgren-Lawrence classification. Arthroscopy was performed in 2 patients. The fibula osteotomy was 7 cm away from the fibular head, with 1 cm resected bone fragment from the fibula. RESULTS: The average duration of the surgery was 30 minutes. Patients were followed up on the 7th day, first month, 3 months and 6 months after surgery. The final evaluation of function was done after 6 months by examining the active and passive movements of the knee joint. In all 14 patients we have excellent results with pain reduction, improvement of movement and quality of life. CONCLUSION: Proximal fibular osteotomy is an option for medial compartment osteoarthritis of the knee. Current literature is limited to small case series which report good outcomes in pain reduction, including the correction of varus deformity in medial gonarthrosis. Further studies are needed to determine the place of the PFO in the medial gonarthrosis management algorithm before it can be recommended for routine clinical use.

Comparative analysis of gait: Similar coronal but different sagittal effects between closing-wedge and opening-wedge high tibial osteotomy.

BACKGROUND: High tibial osteotomy is an established surgical option for medial compartment osteoarthritis of the knee with varus alignment. It can be divided into open wedge and closing wedge by operative technique. Although they have fundamental differences, little is known about the biomechanical consequences of the two surgical methods. METHODS: Thirty-eight patients with medial compartment osteoarthritis who underwent high tibial osteotomy (19 open-wedge and 19 closing-wedge) were retrospectively reviewed. Clinical scores and radiological measurements were assessed until postoperative two years. Gait analysis was performed preoperatively and again at postoperative one year. FINDINGS: Varus alignment was corrected in both groups without a significant difference between them (p = 0.543). However, posterior tibial slope was higher, and the Blackburne-Peel ratio was lower in the open wedge osteotomy group after surgery (both p < 0.001). Reduction of dynamic knee varus and knee adduction moment were observed in both groups without significant differences. However, after surgery, average knee range of motion (63.3° vs 57.3°, p < 0.001) and the magnitude of knee flexion moment was significantly lower (p = 0.005) in the closing wedge group. There were no significant differences in the Kujala Anterior Knee Pain Scale and the occurrence of patellofemoral arthritis between the groups postoperatively. INTERPRETATION: After osteotomy, a smaller average knee range of motion in the sagittal plane and a higher knee flexion moment were observed in the open wedge osteotomy group, suggesting quadriceps muscle avoidance. However, no differences in clinical scores or the short-term occurrence of patellofemoral arthritis were noted between the two surgical techniques.

[Patient-specific cutting guides in corrective osteotomy near to the knee joint]. / Patientenspezifische Schnittblöcke bei kniegelenknahen Korrekturosteotomien.

OBJECTIVE: Patient-specific cutting guides (PSCG) are used in osteotomy near to the knee joint to simplify the operative technique, shorten the duration of surgery, reduce radiation exposure and to exactly realize the preoperative planning during surgery, especially when complex deformities are corrected simultaneously in multiple planes. INDICATIONS: The application of PSCG is in principle possible in all osteotomies near to the knee joint but is especially useful in multidimensional, complex osteotomy. CONTRAINDICATIONS: No specific contraindications. SURGICAL TECHNIQUE: After multidimensional 3D analysis and planning using a preoperative computed tomography (CT) protocol, a 3D-printed patient-specific cutting guide is produced. This PSCG is used during standard osteotomy near to the knee. Using this PSCG the guided sawcut and predrilling of the screw positions inside the bone for the screws of the planned angle stable osteotomy plate are performed. The amount of the deformity correction needed is "stored" in the PSCG and is converted to the bony geometry during placement of the screws in the predrilled holes through the plate after opening or closing the osteotomy. Apart from that, the surgical approach and technique are equivalent to the standard osteotomy types near to the knee. POSTOPERATIVE MANAGEMENT: The application of PSCG in osteotomy near to the knee does not change the postoperative management of the specific osteotomy. RESULTS: The use of patient-specific cutting guides leads to a higher accuracy in the implementation of the preoperative planning and the desired target axis is achieved with greater accuracy. Multidimensional complex corrections can also be exactly planned and implemented. In addition, the intraoperative radiation exposure for the operation team can possibly be reduced.

Use of the flat panel detector fluoroscope reduces radiation exposure during periacetabular osteotomy.

The Periacetabular Osteotomy is a technically demanding procedure that requires precise intraoperative evaluation of pelvic anatomy. Fluoroscopic images pose a radiation risk to operating room staff, scrubbed personnel, and the patient. Most commonly, a Standard Fluoroscope with an Image Intensifier is used. Our institution recently implemented the novel Fluoroscope with a Flat Panel Detector. The purpose of this study was to compare radiation dosage and accuracy between the two fluoroscopes. A retrospective review of a consecutive series of patients who underwent Periacetabular Osteotomy for symptomatic hip dysplasia was completed. The total radiation exposure dose (mGy) was recorded and compared for each case from the standard fluoroscope (n = 27) and the flat panel detector (n = 26) cohorts. Lateral center edge angle was measured and compared intraoperatively and at the six-week postoperative visit. A total of 53 patients (96% female) with a mean age and BMI of 17.84 (± 6.84) years and 22.66 (± 4.49) kg/m2 (standard fluoroscope) and 18.23 (± 4.21) years and 21.99 (± 4.00) kg/m2 (flat panel detector) were included. The standard fluoroscope averaged total radiation exposure to be 410.61(± 193.02) mGy, while the flat panel detector averaged 91.12 (± 49.64) mGy (p < 0.0001). The average difference (bias) between intraoperative and 6-week postoperative lateral center edge angle measurement was 0.36° (limits of agreement: - 3.19 to 2.47°) for the standard fluoroscope and 0.27° (limits of agreement: - 2.05 to 2.59°) for the flat panel detector cohort. Use of fluoroscopy with flat panel detector technology decreased the total radiation dose exposure intraoperatively and produced an equivalent assessment of intraoperative lateral center edge angle. Decreasing radiation exposure to young patients is imperative to reduce the risk of future comorbidities.

Factors Causing Unintended Sagittal and Axial Alignment Changes in High Tibial Osteotomy: Comparative 3-Dimensional Analysis of Simulation and Actual Surgery.

BACKGROUND: Unintended secondary changes in the posterior tibial slope (PTS) and tibial torsion angle (TTA) may occur after medial open-wedge high tibial osteotomy (MOWHTO). In surgical procedures using patient-specific instruments (PSIs), it is essential to reproduce the PTS and TTA that were planned in simulations. PURPOSE: To analyze the factors causing unintended sagittal and axial alignment changes after MOWHTO. STUDY DESIGN: Case series; Level of evidence, 4. METHODS: Overall, 63 patients (70 knees) who underwent MOWHTO using a PSI between June 2020 and June 2023 were retrospectively reviewed. Preoperative and postoperative computed tomography scans were 3-dimensionally reconstructed. Simulated osteotomy was performed so that the weightbearing line could pass through the target point. A PSI gapper was 3-dimensionally printed to fit the posteromedial corner of the osteotomy gap in the simulated HTO model. After MOWHTO using the PSI gapper, the actual postoperative model was compared with the preoperative or simulation model. This assessment included PTS, TTA, hinge axis, and osteotomy-related parameters. Cortical breakage around the lateral hinge was evaluated to assess stability. RESULTS: The mean PTS and TTA did not change in the simulation. However, significant changes were observed in the actual postoperative PTS and TTA (change, -2.4°± 2.2° and -3.9°± 4.7°, respectively). The PTS was reduced, while the TTA decreased with internal rotation of the distal fragment. The difference in the axial hinge axis angle (AHA) between the simulation and actual surgery was the factor most correlated with the difference in the PTS (r = 0.625; P < .001). In regression analysis, the difference in the AHA was the only factor associated with the difference in the PTS (ß = 0.558; P = .001), and there were no factors that showed any significant associations with the difference in the TTA. In subgroup analyses for the change in the TTA, the correction angle and anterior osteotomy angle were significantly higher in the more internal rotation group (P = .023 and P = .010, respectively). The TTA change was significantly higher in the unstable group with lateral cortical breakage (P = .018). The unstable group was more likely to show an internal rotation of ≥5° (odds ratio, 5.0; P = .007). CONCLUSION: The AHA was associated with a difference in the PTS between the simulation and actual surgery. The change in the TTA was caused by a combination of multiple factors, such as a large correction angle and anterior osteotomy angle, but mainly by instability of the lateral cortical hinge.