Systematic literature review of heavy metal contamination of the Nigerian environment from e-waste management: Associated health and carcinogenic risk assessment.

E-waste -the aftermath of large amount of electrical and electronic equipment ferried into Africa from which Nigeria receives a significant chunk, is composed of components known to be hazardous to health. Composition of series of heavy metals (HMs) in e-waste is traceable to many health conditions including cancer which is hitherto incompletely understood. This study harmonizes primary data on HMs from e-waste in different Nigerian environmental media including the air, soil, surface dust, water and plant. We estimated the possible health implications, single and aggregative soil and water pollution indices both in adult and children categories, carcinogenic and non-carcinogenic risks secondary to HM exposure and mapped out the possible mechanism of carcinogenesis. Analysis showed that soil, water, surface dust and plant matrices in Nigerian environment are variedly but considerably contaminated with combination of HMs. The significantly high values of the hazard quotient and hazard index of both water and surface dust matrices are indicative of adverse health effect of the non-carcinogenic risk. The highest HQ is generated by Pb and Cr through dermal exposure to soil and surface dust with mean values of 1718.48, 1146.14, 1362.10 and 1794.61 respectively among Nigerian children followed by the oral exposure. This pattern of observation is similar to that obtained for adult category. HI due to Pb and Cr in soil constitutes the highest HI (2.05E+03 and 1.18E+03 respectively) followed by surface dust. However, this study precipitates the observation that children are more at health risk than adults in contaminated environment. Carcinogenic risk also follows the same pattern of expression in the Nigerian environment. We conclude that exposure to e-waste poses significant carcinogenic and non-carcinogenic health risks and the induction of toxicity may be mediated via DNA damage, oxidative stress and inflammatory/immune cells dysfunction in Nigerian environment.

Process and systematic study of gold recovery from flexible printed circuit boards (FPCBs) using a choline chloride-ethylene glycol system.

The traditional hydrometallurgy technology has been widely used to recover precious metals from electronic waste. However, such aqueous recycling systems often employ toxic/harsh chemicals, which may cause serious environmental problems. Herein, an efficient and environment-friendly method using a deep eutectic solvent (DES) mixed system of choline chloride-ethylene glycol-CuCl2·2H2O is developed for gold (Au) recovery from flexible printed circuit boards (FPCBs). The Au leaching and precipitation efficiency can reach approximately 100 % and 95.3 %, respectively, under optimized conditions. Kinetic results show that the Au leaching process follows a nucleation model, which is controlled by chemical surface reactions with an apparent activation energy of 80.29 kJ/mol. The present recycling system has a much higher selectivity for Au than for other base metals; the two-step recovery rate of Au can reach over 95 %, whereas those of copper and nickel are < 2 %. Hydrogen nuclear magnetic resonance spectroscopy (HNMR) and density functional theory (DFT) analyses confirm the formation of intermolecular hydrogen bonds in the DES mixed system, which increase the system melting and boiling points and facilitate the Au leaching process. The Au leaching system can be reused for several times, with the leaching efficiency remaining > 97 % after five cycles. Moreover, ethylene glycol (EG) and choline chloride (ChCl) act as aprotic solvents as well as coordinate with metals, decreasing the redox potential to shift the equilibrium to the leaching side. Overall, this research provides a theoretical and a practical basis for the recovery of metals from FPCBs.

Unexpectedly high levels and health risks of atmospheric polychlorinated biphenyls in modern mechanical dismantling of obsolete electrical equipment: Investigations in a large integrated e-waste dismantling industrial estate.

Large industrial estates for electrical and electronic waste (e-waste) mechanical dismantling and recycling are gradually replacing outmoded small factories and intensive domestic workshops for e-waste manual and chemical dismantling. However, the air pollution and health risks of persistent organic pollutants during the modern mechanical processing of e-waste, especially obsolete electrical equipment, still remain unclear. Here, unexpectedly high levels (409.3 ng/m3) and health risks of airborne polychlorinated biphenyls (PCBs) were found during the mechanical processing of obsolete electric equipment or parts in a large integrated dismantling industrial estate, which is comparable to or a dozen times higher than those reported during chemical processing. In contrast, the levels (936.0 pg/m3) and health risks of particulate polybrominated diphenyl ethers (PBDEs) were all lower than those of previous studies. PCB emissions (44.9-3300.5 ng/m3) varied significantly across six mechanical dismantling places specifically treating waste motors, electrical appliances, hardware, transformers, and metals, respectively. The high PCB content and mass processing number of obsolete electrical equipment probably result in the highest PCB emissions from the mechanical dismantling of obsolete motors, followed by waste electrical appliances and metals. The PCB non-cancer and cancer risks associated with inhalation and dermal exposure in different mechanical dismantling places were all above the given potential risk limits. In particular, the health risks of dismantling obsolete motor exceeded the definite risk levels. Little difference in PCB emissions and health risks between working and non-working time suggested the importance of PCB volatilization from most e-waste. Such high PCB emissions and health risks of PCBs undoubtedly posed a severe threat to frontline workers, but fortunately, they decreased significantly with the increasing distance from the industrial estate. We highlight that PCB emissions and associated health risks from obsolete electrical equipment with high PCB content during mechanical dismantling activities should be of great concern.

Research on compound pollution characteristics and health risk evaluation of particulate matter and heavy metals in waste glass recycling process.

Owing to the large amount of waste glass generated, the waste glass recycling base is an indispensable municipal supporting facility of a sustainable city. However, waste glass recycling is a complex process involving stages such as multiple-stage crushing and material sorting. Consequently, waste glass recycling base has a considerable impact on the surrounding environment, such as health risk of particulate matter on workers. In this study, we aimed to perform a comprehensive investigation and analysis of compound pollution characteristics and health risk evaluation of particulate matter and heavy metals generated from waste glass recycling process. Soil, particulate fallout, and glass samples were collected from inside and outside a recycling plant in eastern China. Our findings showed that the waste glass treatment process produces a large amount of air particulate matter, and the PM2.5 and PM10 concentrations can reach 3725 and 4055 µg/m3, respectively, in the production workshop during working hours. Meanwhile, the monitoring results show that the concentration of heavy metals on fine particles is higher compared to coarse particles. The high Zn and Pb concentrations detected in the soil and dustfall were proved to be derived from the glass raw materials. However, health risk assessment and particle deposition modeling in the human respiratory system revealed that heavy metals from the air particulate matter have no significant carcinogenicity or non-carcinogenic risk. The Gaussian dispersion model showed that the impact of particulate matter on the surrounding environment and health of the surrounding residents is minimal. Furthermore, transportation is the major emission link according to the particulate emission calculation, indicating that it is imperative to upgrade and reform the existing processes of waste glass recycling. Taken together, this study provides a scientific basis for the green development of waste glass recycling process and further environmental information regarding waste glass recycling plants.

A comparative study on metal pollution from surface dust of informal and formal e-waste recycling sectors in national capital region of New Delhi and associated risk assessment.

Electrical and electronic waste (e-waste) is considered as resource and secondary source of metals, and is being recycled for recovery of precious and base metals. But the processes of recycling and the waste generated during e-waste recycling in informal and formal sectors contribute toxic metals in to the environment. This work aimed to compare the environmental and health impacts of informal and formal e-waste recycling facilities at New Delhi and Bhiwadi Industrial area in India, respectively. Here, concentrations of Ba, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, Sn, V, Zn, and Ag, and As in surface dust collected from informal and formal recycling sectors and their associated pollution, human health and ecological risk are presented. Metal concentrations were higher than the background levels in both sectors. Contamination factor (Cf), contamination degree (Cdeg), pollution load index (PLI), geo-accumulation index (Igeo) and enrichment factor (EnF) of metals indicated severe pollution levels in both sectors. However, contamination in informal sector was comparatively higher than the formal sector. Sampling sites in both sectors had very high ecological risk. Storage, dismantling/shredding and recycling techniques were contributors of metals in surface dust in formal sector whereas fumes deposition, re-suspension, and dried by-products during acid bath treatments were additional sources in informal sector. Metal pollution depends on metal(s), e-waste type(s) and recycling sector(s). Total non-carcinogenic health risk due to metals was 6.5E+00 and 6.0E+01 and 6.2E+00 and 5.5E+01 in adult and children in informal and formal sectors, respectively. Total carcinogenic risk was 3.3E-03 and 7.2E-03 in informal and formal sectors, respectively. Ingestion was major pathways of metals followed by dermal and inhalation and children were more prone to risk compared to adults. Formal sectors too cause metal pollution but to lesser degree compared to informal. More effective pollution control measures are required in formal sector to control environmental pollution.

Elicitation of E-waste (acrylonitrile-butadiene styrene) enriched soil bioremediation and detoxification using Priestia aryabhattai MGP1.

Given the rise in both usage and disposal of dangerous electronics, there is a catastrophic rise in assemblage of electronic waste (e-waste). E-waste including various plastic resins are among the most frequently discarded materials in electronic gadgets. In current digital era, managing e-waste has become universal concern. From the viewpoint of persisting lacuna of e-waste managing methods, the current study is designed to fabricate an eco-friendly e-waste treatment with native soil bacteria employing an enrichment culture method. In the presence of e-waste, indigenous soil microbes were stimulated to degrade e-waste. Microbial cultures were isolated using enrichment medium containing acrylonitrile-butadiene styrene (ABS) as the primary carbon source. Priestia aryabhattai MGP1 was found to be the most dominant e-polymer degrading bacterial isolate, as it was reported to degrade ABS plastic in disposed-off television casings. Furthermore, to increase degradation potential of MGP1, Response Surface Methodology (RSM) was adopted which resulted in optimized conditions (pH 7, shaking-speed 120 rpm, and temperature 30 °C), for maximum degradation (18.88%) after 2 months. The structural changes induced by microbial treatment were demonstrated by comparing the findings of Field emission scanning electron microscopy (FESEM) images and Fourier Transform Infrared (FTIR) spectra confirming the disappearance of ≡ C─H peaks along with C-H, C=C and C ≡N bond destabilization following degradation. Energy-dispersive X-ray (EDX) analyzers of the native and decomposed e-polymer samples revealed a considerable loss in elemental weight % of oxygen by 8.4% and silica by 0.5%. Magnesium, aluminium and chlorine which were previously present in the untreated sample, were also removed after treatment by the bacterial action. When seeds of Vigna radiata were screened using treated soil in the presence of both e-waste and the chosen potent bacterial strain, it was also discovered that there was reduced toxicity in terms of improved germination and growth metrics as a phytotoxicity criterion.

Eco-friendly approach for enhancing the floatability of non-metallic components in waste printed circuit boards: Adding gutter oil during dry grinding.

Waste printed circuit boards (WPCBs) are an attractive secondary resource that is challenging to dispose of due to its complexity. Reverse flotation is an effective method to remove non-metallic particles (NMPs) to obtain metals from WPCBs. Nevertheless, the removal of NMPs is usually inadequate in the present flotation practice. Thus, to provide a clean approach to improve the removal efficiency of NMPs, the method of adding gutter oil during dry grinding process was adopted to enhance the hydrophobic sites on the surface of NMPs to improve the floatability. The surface morphology of NMPs was analyzed by SEM, the results show that the rough morphology inhibited the adhesion of bubbles, while water occupied the cracks and pores, making it challenging for collector adsorption, which result in unstable particle-bubble adhesion. The results of FTIR indicate that both NMPs and gutter oil have -CH3, -CH2, -C = O, -C-O functional groups, which promotes the adsorption of gutter oil on the surface of NMPs. The contact angle (CA) results show that the adsorption of gutter oil on the particle surface is conducive to the formation of enhanced CA. Furthermore, the flotation enhancement effect was verified by flotation kinetic experiments. The accumulated floats yield of NMPs conditioned by gutter oil during grinding is increased from 67.05% (NMPs without conditioning) to 95.02%, and the resin recovery is increased by 31.10%. It is demonstrated that dry grinding with gutter oil can strengthen the floatability of NMPs, which provides a potential approach to increase the flotation efficiency of WPCBs.

Are UK E-waste recycling facilities a source of environmental contamination and occupational exposure to brominated flame retardants?

Investigations into the impacts of regulated electrical and electronic waste (e-waste) recycling activities on urban environments in Europe remain rather scarce. In this study, dust samples taken both inside and outside of five UK e-waste recycling facilities were analysed for concentrations of polybrominated diphenyl ethers (PBDEs), novel brominated flame retardants (NBFRs), and hexabromocyclododecane (HBCDD). Average concentrations of ∑BFRs in dust inside and outside UK e-waste recycling facilities were 12,000 ng/g and 180 ng/g, with median concentrations of 7500 ng/g and 85 ng/g, respectively. BDE-209 and decabromodiphenyl ethane (DBDPE) were the most abundant BFRs in both indoor and kerb dust, making a combined contribution to ∑BFRs of ~90 % on average. While four out of the five studied e-waste facilities showed a lack of significant impact on BFR contamination in surrounding environment, one of the studied e-waste recycling facilities was identified as a likely source of BFR contamination to UK urban environments, with industrial activities as another potential source of NBFRs. Occupational exposure of UK e-waste recycling workers to BFRs via dust ingestion was generally lower than that estimated for e-waste recyclers from other countries, but was comparable to BFR exposure via dust ingestion of UK office workers. Our estimates suggested that health burdens posed by dust ingestion of BFRs were minimal for UK e-waste recycling workers.

The Spatial Distribution and Potential Risk Assessment of POPs in Farmland around a Typical E-Waste Dismantling Site.

Pollution from electronic-waste (E-waste) dismantling is of great concern. This study investigated the concentrations of polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs), and polybrominated diphenyl ethers (PBDEs) in 253 cropland soil samples around an abandoned E-waste dismantling site in Taizhou city, Zhejiang province in China, using an analytical method which simultaneously extracted, purified and determined the identity and quantity of the three types of persistent organic pollutants. Meanwhile, their spatial distributions, pollution characteristics, and risk assessments were further analyzed. Total PCBs in the test soils ranged from below method detection limits (ND) to 2985.25 µg kg-1 on a dry weight basis (d.w.), and the spatial distribution indicated a "hot spot" of PCBs pollution in the study area. The PAHs were detected in all samples with total concentrations ranging from 4.99 to 2723.06 µg kg-1 d.w. The distribution of PBDEs showed the pollution characteristics of "family-run workshops", with a total content range of ND ~ 899.34 µg kg-1 d.w., of which BDE209 was typically the dominant congener, accounting for 74.05% of the total PBDEs content in the test soils, with the highest content reaching 857.72 µg kg-1 d.w. Results showed that the ecological and lifetime carcinogenic risks of PCBs and PAHs were low in the study area, but the health risk caused by oral ingestion and dermal contact accounted for the highest proportion of the total exposure risks, while inhalation could be ignored. PBDEs in soils of the study area were a potential chronic non-carcinogenic risk, particularly for children. Therefore, in order to protect human health and environment, it is necessary to regulate the management of E-waste dismantling sites and pollution control.

Preferential association of polycyclic aromatic hydrocarbons (PAHs) with soil colloids at an e-waste recycling site: Implications for risk of PAH migration to subsurface environment.

Polycyclic aromatic hydrocarbon (PAH) contamination at e-waste recycling sites poses high ecological and human-health risks. Of note, PAHs in surface soils can be mobilized through colloid-facilitated transport, and may migrate into the subsurface and pollute groundwater. Here, we show that the colloids released from the soil samples at an e-waste recycling site in Tianjin, China contain high concentrations of PAHs, with total concentrations of 16 PAHs as high as 1520 ng/g dw. Preferential association of the PAHs with the colloids is observed, with the distribution coefficients of PAHs between colloids and bulk soil often above 10. Source diagnostic ratios show that soot-like particles are the main source of PAHs at the site, due to the incomplete combustion of fossil fuels, biomass, and electronic wastes during the e-waste dismantling practices. Due to their small sizes, a large fraction of these soot-like particles can be remobilized as colloids, and this explains the preferential association of PAHs with colloids. Moreover, the colloids-soil distribution coefficients are higher for the low-molecular-weight PAHs than for the high-molecular-weight ones, possibly attributable to the different binding routes/modes of these two groups of PAHs to the particles during combustion. Notably, the preferential association of PAHs with colloids is even more pronounced for the subsurface soils, corroborating that the presence of PAHs in the deeper soils is primarily the results of downward migration of PAH-bearing colloids. The findings highlight the important role of colloids as a vector for the subsurface transport of PAHs at e-waste recycling sites, and call for further understanding of colloid-facilitated transport of PAHs at e-waste recycling sites.

Elevated levels of biomarkers of oxidative stress and renal injury linked to nitrogenous flame retardants exposure in e-waste dismantling site: A case study in China.

Nitrogenous flame retardants (NFRs) have aroused worldwide public concern as their nephrotoxic effect. However, knowledge regarding the pathogenesis mechanism of their exposure to induce kidney injury remains largely unknown. In this study, eight NFRs, four oxidative stress biomarkers (OSBs), and one kidney injury biomarker, namely neutrophil gelatinase-associated lipocalin (NGAL), were measured in urine specimens collected from residents living around e-waste disassembly and reference areas, representing two exposure scenarios. Significant higher concentrations of Σ8NFR (median: 70.6 vs. 33.8 µg/g Cre) and five biomarkers (124 vs. 97.4 µg/g Cre) were found in urines of populations living in e-waste site compared to those in the reference site (p < 0.05). Primary NFRs exhibited significant positive associations with OSBs and NGAL regardless of the population examined, implying that chronic NFRs exposure could induce oxidative stress and kidney damage. By using structure equation model, we found that oxidative stress, particularly DNA and RNA oxidation mediated 16.1% of the total effect of NFRs on NGAL in e-waste related people, but not on the general population. Overall, this study suggests long-term chronic exposure to NFRs can induce oxidative stress and renal injury in humans but the pathogenesis mode may be scenario-specific.

Co-exposure levels of volatile organic compounds and metals/metalloids in children: Implications for E-waste recycling activity prediction.

Identifying informal e-waste recycling activity is crucial for preventing health hazards caused by e-waste pollution. This study attempted to build a prediction model for e-waste recycling activity based on the differential exposure biomarkers of the populations between the e-waste recycling area (ER) and non-ER. This study recruited children in ER and non-ER and conducted a quasi-experiment among the adult investigators to screen differential exposure or effect biomarkers by measuring urinary 25 volatile organic compound (VOC) metabolites, 18 metals/metalloids, and 8-hydroxy-2'-deoxyguanosine (8-OHdG). Compared with children of the non-ER, the ER children had higher metal/metalloid (e.g., manganese [Mn], lead [Pb], antimony [Sb], tin [Sn], and copper [Cu]) and VOC exposure (e.g., carbon-disulfide, acrolein, and 1-bromopropane) levels, oxidative DNA damage, and non-carcinogenic risks. Individually added 8-OHdG, VOC metabolites, and metals/metalloids to the support vector machine (SVM) classifier could obtain similar classification effects, with the area under curve (AUC) ranging from 0.741 to 0.819. The combined inclusion of 8-OHdG and differential VOC metabolites, metals/metalloids, and mixed indexes (e.g., product items or ratios of different metals/metalloids) in the SVM classifier showed the highest performance in predicting e-waste recycling activity, with an AUC of 0.914 and prediction accuracy of 83.3 %. "Sb × Mn", followed by "Sn × Pb/Cu", "Sb × Mn/Cu", and "Sn × Pb", were the top four important features in the models. Compared with non-ER children, the levels of urinary Mn, Pb, Sb, Sn, and Cu in ER children were 1.2 to 2.4 times higher, while the levels of "Sb × Mn", "Sn × Pb/Cu", "Sb × Mn/Cu", and "Sn × Pb" were 3.5 to 4.7 times higher, suggesting that these mixed indexes could amplify the differences between e-waste exposed and non-e-waste exposed populations. With the continued inclusion of new biomarkers of e-waste pollution in the future, our prediction model is promising for screening informal e-waste recycling sites.

Geochemical distribution and environmental risk assessment of trace metals in groundwater released from e-waste management activities in Lahore, Pakistan.

Non-sustainable e-waste recycling and dumping activities release trace metals into the ambient environment where they may threaten the biological communities and human health. A total of 45 groundwater and 21 leachate samples were collected from seven recycling, seven dumping, and one reference site in Lahore, Pakistan, and analyzed for Cu, Pb, Zn, Cd, Mn, and Fe in atomic absorption spectrophotometer. Comparing the results with the World Health Organization (WHO) standards of drinking water, only the concentrations of Cu, Zn, Mn, and Fe at all sites were found to be within the permissible limits, i.e., 2, 3, 0.5, and 1 mg/L, respectively. In leachates, only Cd and Mn at one site (0.204 and 8.636 mg/L, respectively) exceeded the allowable limits of National Environmental Quality Standards of Municipal and Liquid industrial effluents. Geo-accumulation index, contamination factor, contamination degree, and pollution load index values showed no to moderate contamination. The ecological risk index did not exceed 150, depicting low risk to nearby biological communities. The non-carcinogenic health risk assessment showed a hazard index value greater than 1 at all sites for children (2.04) and adults (1.52), with Pb being the major contributor to adverse health impacts via ingestion and dermal route. Children (1.21 × 10-4) were at a more significant threat of carcinogenic risk from Pb and Cd as compared to adults (8.10 × 10-5). Therefore, there is a dire need to introduce sustainable e-waste recycling and managing techniques to reduce further groundwater contamination via the percolation of trace metals and to reduce the current contamination level.

E-waste management, treatment options and the impact of heavy metal extraction from e-waste on human health: Scenario in Vietnam and other countries.

Ho Chi Minh (HCM) City is the most important urban region of Vietnam, Southeast Asia. In recent times, the quantity of electronic waste (e-waste) has been growing by several thousand tonnes every year. In this research, some of the existing and developing technologies being employed for the recycling of e-waste have been reviewed. Accordingly, the paper has been divided into three sections namely, e-waste treatment technologies in Ho Chi Minh City, the effect of heavy metals on human health and the extraction of metals from e-waste using pyrolysis, hydrometallurgy, bioleaching, mechanical, and air classifier methods, respectively. The extraction of precious metals and heavy metals such as Cd, Cr, Pb, Hg, Cu, Se, and Zn from e-waste can be hazardous to human health. For example, lead causes hazards to the central and peripheral nervous systems, blood system and kidneys; copper causes liver damage; chronic exposure to cadmium ends up causing lung cancer and kidney damage, and mercury can cause brain damage. Thus, this study examines the key findings of many research and review articles published in the field of e-waste management and the health impacts of metal pollution.

Remediation of metals and plastic from e-waste by iron mine indigenous acidophilic bacteria.

The growing consumption of electrical and electronic equipment leads to high amounts of electronic waste (e-waste), which is now considered the fastest-growing waste stream at the national and international levels. As well as being a potential secondary resource due to its precious metals content, e-waste also contains strategic metals and plastics. For instance, mobile phones have about 25-55% plastic substances. A few studies have been performed to investigate the potential of indigenous bacteria in metals' bioleaching from the polluted environment. Heterotrophic bioleaching potential in acidic conditions had been preliminarily investigated. Two soil types of iron ore were considered the source of indigenous bacteria. Despite the acidophilic nature of the bacterial consortium, they continued their leaching activity regardless of alkaline conditions. Maximum biorecovery rate related to copper (4%) responding to the main soil, owing to the higher copper content of mobile phone waste. Chromium had the least recovery rate (⩽0.002%). Overall, the maximum metal recovery rate was 4.7%, achieved by tailing heterotrophs at an e-waste loading of 10 g l-1. Statistical analysis had shown that there was no significant difference between the metal recovery rates and soil type or even the solid-liquid ratio (p > 0.05). Although acidophilic indigenous heterotrophs could not be an appropriate alternative for a large amount of metal recovery process, they might have considerable potential in the bioremediation of e-waste plastic fractions and metals in low concentrations simultaneously.

Handwipes as indicators to assess organophosphate flame retardants exposure and thyroid hormone effects in e-waste dismantlers.

Dermal exposure is increasingly recognized as an important pathway for organic pollutant exposure. However, data on dermal exposure are limited, particularly with respect to the health effects. This study evaluated association between organophosphorus flame retardants (OPFRs) in handwipes and internal body burden on workers and adult residents in an electronic waste (e-waste) dismantling area. The impact of dermal exposure to OPFRs on thyroid hormones (THs) served as a biomarker for early effects. Triphenyl phosphate (TPhP) was the most detected compound in handwipes, with median levels of 1180, 200, and 24.0 ng in people identified as e-waste bakers, e-waste dismantlers, and adult residents. Among e-waste dismantlers, TPhP levels in handwipes were positively correlated with paired serum TPhP and urinary diphenyl phosphate (DPhP) levels. In multiple linear regression models controlling for sex, age and smoking, TPhP levels in handwipes of e-waste dismantlers were significantly negatively correlated with three THs used to evaluate thyroid function: serum reverse 3,3',5-triiodo-L-thyronine (rT3), 3,3'-diiodo-L-thyronine (3,3'-T2), and 3,5-diiodo-L-thyronine (3,5-T2). These findings suggest that handwipes can act as non-invasive exposure indicators to assess body burden of dermal exposure to TPhP and health effects on THs of e-waste dismantlers. This study highlights importance of OPFR effect on human THs through dermal exposure.

Synthesis and Characterization of Ferrous and Copper Nanoparticles from E-Waste Using Biological Reduction by Lichen-Associated Bacteria and Their Application in Antifouling Activity.

The largest and fastest growing industry in the world is electronic industries and the generation of waste are emerging problem. Electronic wastes are the source of precious metals that contributes 40 to 50 times more than the ore extracted from mines. The recycling of the waste is very important as it can protect the earth's natural resources. There are various methods for recycling e-waste such as chemical, fire, physical, and mechanical method. Currently, chemical treatment is in practice for recycling but, due to the usage of inorganic chemicals, it gives more environmental issues. Therefore, this paper used the biological method to prepare the nanoparticle from e-waste as it is an eco-friendly method. The copper and ferrous nanoparticle was extracted from the e-waste and biologically reduced using lichen-associated bacterial such as Parmotrema tintorum and P. recticulatum. The characteristics of these nanoparticles such as size, shape, and functional group were analyzed using UV, PSA, SEM, and FTIR respectively. The size of the synthesized particle was in the range of 10-100 nm using PSA. At the 2.5% concentration, the synthesis of ferrous nanoparticles was confirmed by the peak value obtained at 430 nm and 540 nm for copper nanoparticles. The antifouling properties of synthesized nanoparticles were analyzed by colliding them with the paint and applying to the iron surface. In recent research, the nanomaterials were able to use to reduce the fouling activity, also prevent harmful effects to the other marine species and the resistance of some microorganisms to antifoulants. This study helps to prevent environmental contaminants by using the copper and ferrous nanoparticle substances synthesized from the e-waste materials with the help of bacterial reduction.

Evaluation and environmental risk assessment of heavy metals in the soil released from e-waste management activities in Lahore, Pakistan.

In developing regions, electronic waste either gets recycled by using crude and primitive techniques in recycling centers or dumped in dumping grounds that result in the leaching of heavy metals into the ambient environment. The objective of this study is to determine the concentration of heavy metals (Cu, Pb, Zn, Cd, Mn, and Fe) in the surface soil of recycling centers and dumping sites in Lahore, Pakistan, and to quantify and compare the environmental risk. The mean concentration (mg/kg) of Cu, Pb, Zn, and Cd was 722.96, 446.81, 378.76, and 4.11, respectively in the surface soil of recycling centers, and only the mean concentration of Cu (214.09 mg/kg) from dumping sites were above permissible limits of World Health Organization. Results of the geo-accumulation index (Igeo) and contamination factor (Cf) revealed that the surface soil is highly contaminated with Cu, Pb, and Cd. The Cd content (701.24) caused a very high potential ecological risk (Er) (> 320) to nearby biological communities. The noncarcinogenic risk was only expected from Pb to children (1.70) living near recycling centers, whereas no risk was observed for adults living either near recycling centers (0.23) or dumping sites (0.01). There is a high probability of carcinogenic health risks to children (1.085 × 10-2) and adults (1.195 × 10-3) from Cu. Hence, all the results suggest that e-waste recycling and dumping activities were a significant source of heavy metals to the surrounding environment, children, and adults, so it is strongly recommended to take action for sustainable management of e-waste.

Evaluating postnatal exposure to six heavy metals in a Chinese e-waste recycling area.

This study is the first to assess postnatal exposure to heavy metals using breast milk in an electronic waste (e-waste) recycling area. From January to April 2021, 102 and 97 breastfeeding women were recruited from an e-waste recycling area and a control area, respectively. Four weeks after delivery, medical staff collected 20 mL of breast milk from each participant. The breast milk was tested for six heavy metals (lead, cadmium, chromium, arsenic, copper, and manganese) using inductively coupled plasma mass spectrometry (ICP-MS). The estimated daily intake (EDI) of infants during breastfeeding was calculated to assess the impact of postnatal exposure to heavy metals on infant health. The concentrations of chromium and lead in the breast milk were significantly higher in the e-waste recycling area than in the control area. Chromium concentrations in breast milk was 34.3%, exceeding the permissible limits set by the World Health Organization (WHO), in the e-waste recycling area, which is 16 times higher than that in the control areas. The EDIs of lead and chromium in the e-waste area were twice as those in the control area. This strongly indicates that the potential impact of postnatal exposure to lead and chromium on infant and child health in e-waste recycling areas cannot be ignored. Infants and children in e-waste recycling areas are at risk of long-term exposure to heavy metals. Therefore, ongoing health monitoring is necessary.

Olive-tree polyphenols and urban mining. A greener alternative for the recovery of valuable metals from scrap printed circuit boards.

Recycling printed circuit boards (PCBs) is becoming a source of precious metals and an alternative to conventional mining. This phenomenon is now known as "urban mining." In this work, a polyphenols-rich plant extract has been obtained from olive-tree leaves, and its ability to contribute to reducing four metals, namely, Ag, Cu, Cr, and Sn, that are present in scrap PCBs has been studied. Three reductants (NaBH4, Fe°, and the olive-tree leaves extract) have been used to recover these valuable metals. An attempt has been made to minimize the concentration of the first two, replacing them with a natural, cheaper, and less toxic reductant. To achieve this goal, a computer-assisted factorial, composed, centered, orthogonal, and rotatable statistical design of experiments (FCCORD) has been used to build the experimental matrix to be carried out in the laboratory and, next, for the statistical treatment of the results. The results show that it is possible to achieve only a partial recovery of the four metals (silver, copper, chromium, and tin) from PCBs leachates by using sodium borohydride, iron, and the extract separately. In other words, none of these three reductants alone can completely remove any of the four metals in the leachate. Nevertheless, using the statistical design of experiments, the total recovery of the four metals has been achieved by combining the three reductants in the appropriate concentrations. Hence, polyphenols-rich plant extracts in general and olive-tree leaves extract in particular can be regarded as promising coadjuvants in the rising field of urban mining.