All-printed wearable biosensor based on MWCNT-iron oxide nanocomposite ink for physiological level detection of glucose in human sweat.

Wearable sensors for sweat glucose monitoring are gaining massive interest as a patient-friendly and non-invasive way to manage diabetes. The present work offers an alternative on-body method employing an all-printed flexible electrochemical sensor to quantify the amount of glucose in human sweat. The working electrode of the glucose sensor was printed using a custom-formulated ink containing multi-walled carbon nanotube (MWCNT), poly (3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOPT: PSS), and iron (II, III) oxide (Fe3O4) nanoparticles. This novel ink composition has good conductivity, enhanced catalytic activity, and excellent selectivity. The working electrode was modified using Prussian blue (PB) nanoparticles and glucose oxidase enzyme (GOx). The sensor displayed a linear chronoamperometric response to glucose from 1 µM to 400 µM, with a precise detection limit of ∼0.38 µM and an impressive sensitivity of ∼4.495 µAµM-1cm-2. The sensor stored at 4 °C exhibited excellent stability over 60 days, high selectivity, and greater reproducibility. The glucose detection via the standard addition method in human sweat samples acquired a high recovery rate of 96.0-98.6%. Examining human sweat during physical activity also attested to the biosensor's real-time viability. The results also show an impressive correlation between glucose levels obtained from a commercial blood glucose meter and sweat glucose concentrations. Remarkably, the present results outperform previously published printed glucose sensors in terms of detection range, low cost, ease of manufacturing, stability, selectivity, and wearability.

Enhancing Extracellular Electron Transfer of a 3D-Printed Shewanella Bioanode with Riboflavin-Modified Carbon Black Bioink.

3D printing of a living bioanode holds the potential for the rapid and efficient production of bioelectrochemistry systems. However, the ink (such as sodium alginate, SA) that formed the matrix of the 3D-printed bioanode may hinder extracellular electron transfer (EET) between the microorganism and conductive materials. Here, we proposed a biomimetic design of a 3D-printed Shewanella bioanode, wherein riboflavin (RF) was modified on carbon black (CB) to serve as a redox substance for microbial EET. By introducing the medicated EET pathways, the 3D-printed bioanode obtained a maximum power density of 252 ± 12 mW/m2, which was 1.7 and 60.5 times higher than those of SA-CB (92 ± 10 mW/m2) and a bare carbon cloth anode (3.8 ± 0.4 mW/m2). Adding RF reduced the charge-transfer resistance of a 3D-printed bioanode by 75% (189.5 ± 18.7 vs 47.3 ± 7.8 Ω), indicating a significant acceleration in the EET efficiency within the bioanode. This work provided a fundamental and instrumental concept for constructing a 3D-printed bioanode.

Graphene Nanocomposite Ink Coated Laser Transformed Flexible Electrodes for Selective Dopamine Detection and Immunosensing.

Novel and flexible disposable laser-induced graphene (LIG) sensors modified with graphene conductive inks have been developed for dopamine and interleukin-6 (IL-6) detection. The LIG sensors exhibit high reproducibility (relative standard deviation, RSD = 0.76%, N = 5) and stability (RSD = 4.39%, N = 15) after multiple bendings, making the sensors ideal for wearable and stretchable bioelectronics applications. We have developed electrode coatings based on graphene conductive inks, poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (G-PEDOT:PSS) and polyaniline (G-PANI), for working electrode modification to improve the sensitivity and limit of detection (LOD). The selectivity of LIG sensors modified with the G-PANI ink is 41.47 times higher than that of the screen-printed electrode with the G-PANI ink modification. We have compared our fabricated bare laser-engraved Kapton sensor (LIG) with the LIG sensors modified with G-PEDOT (LIG/G-PEDOT) and G-PANI (LIG/G-PANI) conductive inks. We have further compared the performance of the fabricated electrodes with commercially available screen-printed electrodes (SPEs) and screen-printed electrodes modified with G-PEDOT:PSS (SPE/G-PEDOT:PSS) and G-PANI (SPE/G-PANI). SPE/G-PANI has a lower LOD of 0.632 µM compared to SPE/G-PEDOT:PSS (0.867 µM) and SPE/G-PANI (1.974 µM). The lowest LOD of the LIG/G-PANI sensor (0.4084 µM, S/N = 3) suggests that it can be a great alternative to measure dopamine levels in a physiological medium. Additionally, the LIG/G-PANI electrode has excellent LOD (2.6234 pg/mL) to detect IL-6. Also, the sensor is successfully able to detect ascorbic acid (AA), dopamine (DA), and uric acid (UA) in their ternary mixture. The differential pulse voltammetry (DPV) result shows peak potential separation of 229, 294, and 523 mV for AA-DA, DA-UA, and UA-AA, respectively.

Nanofibrous polyelectrolyte complex incorporated BSA-alginate composite bioink for 3D bioprinting of bone mimicking constructs.

Although several bioinks have been developed for 3D bioprinting applications, the lack of optimal printability, mechanical properties, and adequate cell response has limited their practical applicability. Therefore, this work reports the development of a composite bioink consisting of bovine serum albumin (BSA), alginate, and self-assembled nanofibrous polyelectrolyte complex aggregates of gelatin and chitosan (PEC-GC). The nanofibrous PEC-GC aggregates were prepared and incorporated into the bioink in varying concentrations (0 % to 3 %). The bioink samples were bioprinted and crosslinked post-printing by calcium chloride. The average nanofiber diameter of PEC-GC was 62 ± 15 nm. It was demonstrated that PEC-GC improves the printability and cellular adhesion of the developed bioink and modulates the swelling ratio, degradation rate, and mechanical properties of the fabricated scaffold. The in vitro results revealed that the bioink with 2 % PEC-GC had the best post-printing cell viability of the encapsulated MG63 osteosarcoma cells and well oragnized stress fibers, indicating enhanced cell adhesion. The cell viability was >90 %, as observed from the MTT assay. The composite bioink also showed osteogenic potential, as confirmed by the estimation of alkaline phosphatase activity and collagen synthesis assay. This study successfully fabricated a high-shape fidelity bioink with potential in bone tissue engineering.

Bioprinting Soft 3D Models of Hematopoiesis using Natural Silk Fibroin-Based Bioink Efficiently Supports Platelet Differentiation.

Hematopoietic stem and progenitor cells (HSPCs) continuously generate platelets throughout one's life. Inherited Platelet Disorders affect ≈ 3 million individuals worldwide and are characterized by defects in platelet formation or function. A critical challenge in the identification of these diseases lies in the absence of models that facilitate the study of hematopoiesis ex vivo. Here, a silk fibroin-based bioink is developed and designed for 3D bioprinting. This bioink replicates a soft and biomimetic environment, enabling the controlled differentiation of HSPCs into platelets. The formulation consisting of silk fibroin, gelatin, and alginate is fine-tuned to obtain a viscoelastic, shear-thinning, thixotropic bioink with the remarkable ability to rapidly recover after bioprinting and provide structural integrity and mechanical stability over long-term culture. Optical transparency allowed for high-resolution imaging of platelet generation, while the incorporation of enzymatic sensors allowed quantitative analysis of glycolytic metabolism during differentiation that is represented through measurable color changes. Bioprinting patient samples revealed a decrease in metabolic activity and platelet production in Inherited Platelet Disorders. These discoveries are instrumental in establishing reference ranges for classification and automating the assessment of treatment responses. This model has far-reaching implications for application in the research of blood-related diseases, prioritizing drug development strategies, and tailoring personalized therapies.

Effect of a collagen peptide-fish oil high internal phase emulsion on the printability and gelation of 3D-printed surimi gel inks.

The effect of a high internal phase emulsion (HIPE) on three-dimensional-printed surimi gel inks was studied. Increasing the concentration of collagen peptide decreased the particle size of HIPE droplets and improved the viscoelasticity and stability. For example, when the collagen peptide concentration was 5 wt%, the viscoelasticity of the HIPE was high, as indicated by the presence of small and uniform particles, which formed a monolayer in the outer layer of the oil droplets to form stable a HIPE. A HIPE was used as the filling material to fill the surimi gel network, which reduced the porosity of the network. Surimi protein and peptides have dual emulsifying effects on the stabilization of oil. After adding the emulsion, the texture, gel properties and rheological properties of the surimi were reduced, and its printing adaptability was improved. This study provides new ideas for the production of surimi and its application in 3D printing.

From biomaterials to biotherapy: cuttlefish ink with protoporphyrin IX nanoconjugates for synergistic sonodynamic-photothermal therapy.

Biologically produced nanomaterials capable of therapeutic purposes have received increasing interest in tumor therapy because of their intrinsic biocompatibility. In this study, we made cuttlefish ink (extracted from cuttlefish) and protoporphyrin IX (PpIX) nanoconjugates (CIPs) where PpIX was an endogenous organic compound. In the case of CIPs, PpIX could be triggered by ultrasound (US) for sonodynamic therapy (SDT), and the cuttlefish ink could be excited by a near-infrared laser for photothermal therapy (PTT). Thereafter, tumor growth was greatly inhibited through synergistic SDT-PTT in comparison to single SDT or PTT. In addition, in vivo administration of CIPs showed no noticeable side effects for mouse blood and chief organs, providing an effective strategy for developing biologically produced biomaterials and using them for biotherapy.

Direct ink writing of biocompatible chitosan/non-isocyanate polyurethane/cellulose nanofiber hydrogels for wound-healing applications.

The demand for new biocompatible and 3D printable materials for biomedical applications is on the rise. Ideally, such materials should exhibit either biodegradability or recyclability, possess antibacterial properties, and demonstrate remarkable biocompatibility with no cytotoxic effects. In this research, we synthesized biocompatible and 3D printable hydrogels tailored for biomedical applications, such as wound healing films, by combining antibacterial double-quaternized chitosan (DQC) with cystamine-based non-isocyanate polyurethane (NIPU-Cys) - a material renowned for enhancing both the flexibility and mechanical properties of the hydrogels. To improve the rheological behavior, swelling attributes, and printability, cellulose nanofibrils were introduced into the matrix. We investigated the impact of DQC on degradability, swelling capacity, rheological behavior, printability, and cell biocompatibility. The slightly cytotoxic nature associated with quaternary chitosan was evaluated, and the optimal concentration of DQC in the hydrogel was determined to ensure biocompatibility. The resulting hydrogels were found to be suitable materials for 3D printing via a direct ink writing technique (DIW), producing porous, biocompatible hydrogels endowed with valuable attributes suitable for various wound-healing applications.

Application of Indian ink markers for locating gastric varices under endoscopic ultrasonography.

OBJECTIVE: The present study aimed to investigate the accuracy of endoscopic ultrasonography (EUS) combined with Indian ink in locating target vessels of gastric varices (GVs) compared with conventional endoscopic techniques. Additionally, the characteristics of GVs under conventional endoscopy were also explored. METHODS: All 50 cirrhotic patients with GVs between August 2021 and December 2022 were included in the study. Firstly, conventional endoscopy was employed to identify GVs and to record the expected injection sites. Subsequently, EUS was used to locate the perforated vessel and the injection site was them marked with India ink followed by injection with cyanoacrylate (CYA). Finally, conventional endoscopy was used to examine GVs, to identify the marker points of Indian ink and to compare whether the injection points under conventional endoscopy were consistent with those marked with Indian ink. Furthermore, patients with consistent and inconsistent distribution of endoscopic markers and injection sites were divided into two groups. RESULTS: EUS could detect the perforating vessels in real time and intuitively. The distribution of markers using EUS was significantly different compared with the injection points obtained by conventional endoscopy (P < 0.001). Therefore, 20 cases were allocated to the consistent group and 30 cases to the non-consistent group. 16 patients who showed red wale signs were obtained in the consistent group and 11 patients in the non-consistent group (P = 0.048). The diameter of the largest GVs was 13.5 (10-15) mm in the consistent group compared with 10 (7.5-10) mm in the non-consistent group (P = 0.006). CONCLUSION: EUS could provide the exact location of GVs, thus more accurately describing the endoscopic characteristics of the GVs. Furthermore, the red wale signs and diameter of the largest GVs obtained using conventional endoscopy were helpful in determining the location of target GVs.

Macrophage-like rapid uptake and toxicity of tattoo ink in human monocytes.

Macrophages play a critical role for the persistence of tattoo ink in human skin. However, a comparison to other skin-resident and blood circulating immune cells and a profound analysis of REACH-compliant tattoo ink are unmet medical needs. We hence characterized the size distribution of ink particles using physicochemical methods. We studied the uptake of tattoo ink by key human skin cells and blood-derived immune cells using optical and electron microscopy as well as flow cytometry. Scanning electron microscopy of ink revealed its crystalline structure, and a tendency towards aggregations was indicated by size changes upon diluting it. Flow cytometric analyses of skin and immune cells after incubation with tattoo ink demonstrated an increase in cellular granularity upon uptake and red ink additionally evoked fluorescent signals. Human macrophages were most potent in internalizing ink in full thickness 3D skin models. Macrophage cultures demonstrated that the ink did not lead to elevated inflammatory mediators, and showed no indications for toxicity, even after nice days. Strikingly, monocytes were most efficient in ink uptake, but displayed reduced viability, whereas granulocytes and lymphocytes showed only temporary ink uptake with flow cytometric signals declining after 1 day. Mechanistic studies on ink retention by corticosteroids or dexpanthenol in macrophage cultures demonstrated that these compounds do not lead to ink excretion, but even slightly increase the ink load in macrophages. The highly motile monocytes, precursors of macrophages, may play an underrated role for tattoo ink translocation from dermal blood vessels into internal organs.

The Process of Sterilizing Tattoo Inks Releases Formaldehyde.

INTRODUCTION: Around 12% of Europeans and 20% of Americans have at least one tattoo. Tattoo inks, the substances used to create tattoos on the body, consist of chemicals that contain formaldehyde, which can be harmful to human health. The amount of formaldehyde present in commercially available tattoo inks and its causes are not well understood. METHODS: We investigated the levels of formaldehyde in tattoo ink products sold in different countries and identified the factors contributing to its production. We also explored methods to reduce formaldehyde generation in tattoo inks. Seven tattoo inks from various brands were tested. RESULTS: Formaldehyde release was predominantly associated with gamma radiation sterilization. Formaldehyde levels were observed to be higher in compositions containing organic components compared to those with inorganic components, irrespective of sterilization method and container type. Glycerin released over seven times more formaldehyde than other components during gamma-ray sterilization. CONCLUSION: The results suggest that the presence of hydroxyl groups in carbon organic compounds in tattoo ink leads to photodegradation during gamma-ray radiation sterilization, resulting in increased concentrations of formaldehyde. Further research is needed to examine the chemical reactions occurring during sterilization processes and identify alternative sterilization methods that minimize formaldehyde formation. Additionally, the development of tattoo inks with reduced formaldehyde content and the establishment of strict quality control measures can help ensure the safety of tattooing practices.

Therapeutic potential of enzymatically extracted eumelanin from squid ink in type 2 diabetes mellitus ICR mice: Multifaceted intervention against hyperglycemia, oxidative stress and depression.

BACKGROUND: Type 2 diabetes mellitus (T2DM) is a prevalent metabolic disease that poses significant health risks due to its numerous complications. However, the effects of eumelanin on oxidative stress, hyperglycemia and depression in diabetic mice have not been extensively studied. RESULTS: Our study employed an enzymatic approach to extract eumelanin from squid ink and characterized it using spectroscopic techniques. Remarkably, eumelanin extracted with alkaline-neutral-flavor protease (ANF) displayed superior inhibitory activity against α-glucosidase and α-amylase, while enhancing glucose utilization and hepatic glycogen synthesis in human hepatocellular carcinoma cell line (HepG2) insulin resistance model. Further evaluation of ANF in a T2DM ICR mouse model demonstrated its significant potential in alleviating hyperglycemia, reducing glycosylated serum protein levels, improving glucose tolerance and modulating total cholesterol and low-density lipoprotein levels, as well as antioxidant indices at a dosage of 0.04 g kg-1 . Additionally, ANF exhibited positive effects on energy levels and reduced immobility time in antidepressant behavioral experiments. Moreover, ANF positively influenced the density and infiltration state of renal cells, while mitigating inflammatory enlargement and deformation of liver cells, without inducing any adverse effects in mice. CONCLUSION: Overall, these findings underscore the significant therapeutic potential of ANF in the treatment of T2DM and its associated complications. By augmenting lipid and glucose metabolism, mitigating oxidative stress and alleviating depression, ANF emerges as a promising candidate for multifaceted intervention. © 2023 Society of Chemical Industry.

Development of a C-reactive protein quantification method based on flow rate measurement of an ink solution pushed out by oxygen gas generated by catalase reaction.

A novel determination method for protein biomarkers based on on-chip flow rate measurement was developed using a microchip with organic photodiodes (OPDs). This quantitative method is based on the flow rate measurement of an ink solution pushed out by oxygen gas generated through catalase reaction. The amount of oxygen gas generated in the sample reservoir is dependent on the concentration of the analyte; therefore, the flow rate of the ink solution is also dependent on the concentration of the analyte. The concentration of the analyte can thus be estimated by measurement of the ink solution flow rate. The ink solution flow rate was estimated by measuring the migration time of the ink solution between two points using two OPDs placed below the microchannel. The principle of this method was demonstrated by the measurement of catalase using the microchip. In addition, the developed method was applied to the determination of C-reactive protein (CRP), a biomarker of inflammation, based on a catalase-linked immunosorbent assay (C-LISA). The limit of detection for CRP was 0.20 µg/mL. The method was also applied to the determination of CRP in human serum, and the quantitative values obtained by this method were in excellent agreement with those obtained by the conventional enzyme-linked immunosorbent assay (ELISA) method. The developed method does not require a photodetector with high sensitivity and is thus capable of downsizing; therefore, this will be useful for on-site analyses such as point-of-care testing and field measurements.

An investigation into the effects of ink formulations of semi-solid extrusion 3D printing on the performance of printed solid dosage forms.

Semi-solid extrusion (SSE) 3D printing has recently attracted increased attention for its pharmaceutical application as a potential method for small-batch manufacturing of personalised solid dosage forms. It has the advantage of allowing ambient temperature printing, which is especially beneficial for the 3D printing of thermosensitive drugs. In this study, the effects of polymeric compositions (single hydroxypropyl methylcellulose (HPMC) system and binary HPMC + polyvinylpyrrolidone (PVP) system), disintegrant (silicon oxide (SiO2)), and active pharmaceutical ingredients (tranexamic acid (TXA) and paracetamol (PAC)) on the printability of semisolid inks and the qualities of SSE printed drug-loaded tablets were investigated. Printability is defined by the suitability of the material for the process in terms of its physical properties during extrusions and post-extrusion, including rheology, solidification time, avoiding slumping, etc. The rheological properties of the inks were investigated as a function of polymeric compositions and drug concentrations and further correlated with the printability of the inks. The SSE 3D printed tablets were subjected to a series of physicochemical properties characterisations and in vitro drug release performance evaluations. The results indicated that an addition of SiO2 would improve 3D printing shape fidelity (e.g., pore area and porosity) by altering the ink rheology. The pores of HPMC + PVP + 5PAC prints completely disappeared after 12 hours of drying (pore area = 0 mm2). An addition of SiO2 significantly improved the pore area of the prints which are 3.5 ± 0.1 mm2. It was noted that the drug release profile of PAC significantly increased (p < 0.05) when additive SiO2 was incorporated in the formulation. This could be due to a significantly higher porosity of HPMC + PVP + SiO2 + PAC (70.3 ± 0.2%) compared to HPMC + PVP + PAC (47.6 ± 2.1%). It was also likely that SiO2 acted as a disintegrant speeding up the drug release process. Besides, the incorporation of APIs with different aqueous solubilities, as well as levels of interaction with the polymeric system showed significant impacts on the structural fidelity and subsequently the drug release performance of 3D printed tablets.

Multifunctional Microneedle Patches via Direct Ink Drawing of Nanocomposite Inks for Personalized Transdermal Drug Delivery.

Additive manufacturing, commonly known as 3D printing, allows decentralized drug fabrication of orally administered tablets. Microneedles are comparatively favorable for self-administered transdermal drug delivery with improved absorption and bioavailability. Due to the cross-scale geometric characteristics, 3D-printed microneedles face a significant trade-off between the feature resolution and production speed in conventional layer-wise deposition sequences. In this study, we introduce an economical and scalable direct ink drawing strategy to create drug-loaded microneedles. A freestanding microneedle is efficiently generated upon each pneumatic extrusion and controlled drawing process. Sharp tips of ∼5 µm are formed with submillimeter nozzles, representing 2 orders of magnitude improved resolution. As the key enabler of this fabrication strategy, the yield-stress fluid inks are formulated by simply filling silica nanoparticles into regular polymer solutions. The approach is compatible with various microneedles based on dissolvable, biodegradable, and nondegradable polymers. Various matrices are readily adopted to adjust the release behaviors of the drug-loaded microneedles. Successful fabrication of multifunctional patches with heterogeneously integrated microneedles allows the treatment of melanoma via synergistic photothermal therapy and combination chemotherapy. The personalized patches are designed for cancer severity to achieve high therapeutic efficacy with minimal side effects. The direct ink drawing reported here provides a facile and low-cost fabrication strategy for multifunctional microneedle patches for self-administering transdermal drug delivery.

Preparation of sustainable mineral oil-free offset printing ink with vegetable oil esters.

Mineral oils are used in substantial quantities for the production of varnishes and inks due to their abundance and versatility. However, as part of the production process, some of mineral oil components are separated as waste material, whereupon they can mix with air, water, or soil and become potentially harmful to the environment. Almost all these waste materials are volatile organic compounds (VOCs), chemicals that can easily evaporate at room temperature and have toxic effect. Therefore, a novel green, mineral oil-free offset printing ink was produced using vegetable oil esters as bio-renewable raw materials. Accompanying varnishes were prepared with linseed oil, methyl oleate, octyl stearate, and four types of resin (A, B, C, and D). The application of these varnishes to magenta color offset ink was subsequently studied to screen out the best combination of resin and ester in terms of setting time. Meanwhile, dyeing force tests were conducted to evaluate the ink's printability, while rheological analysis was done via viscosity and flowability tests. The setting time of the magenta color offset ink made by varnish A was observed to be considerably shorter than that of the ink samples prepared using varnishes B, C, and D. Furthermore, varnish A proved to be a good alternative varnish for the production of yellow, cyan, and black color offset printing inks. Samples of these inks were printed on coated paper, and their printability was contrasted against that of vegetable oil-based (pure vegetable oil), mineral oil-based, and other mineral oil-free offset printing inks. Results determined that the varnishes produced with linseed oil, methyl oleate, and octyl stearate can replace mineral oil-based varnishes for the production of offset printing ink.

3D bio-printed hydrogel inks promoting lung cancer cell growth in a lab-on-chip culturing platform.

The results of a lab-on-chip (LOC) platform fabrication equipped with a hydrogel matrix is reported. A 3D printing technique was used to provide a hybrid, "sandwiched" type structure, including two microfluidic substrates of different origins. Special attention was paid to achieving uniformly bio-printed microfluidic hydrogel layers of a unique composition. Six different hydrogel inks were proposed containing sodium alginate, agar, chitosan, gelatin, methylcellulose, deionized water, or 0.9% NaCl, varying in proportions. All of them exhibited appropriate mechanical properties showing, e.g., the value of elasticity modulus as similar to that of biological tissues, such as skin. Utilizing our biocompatible, entirely 3D bio-printed structure, for the first time, a multi-drug-resistant lung cancer cell line (H69AR) was cultured on-chip. Biological validation of the device was performed qualitatively and quantitatively utilizing LIVE/DEAD assays and Presto blue staining. Although all bio-inks exhibited acceptable cell viability, the best results were obtained for the hydrogel composition including 3% sodium alginate + 7% gelatin + 90% NaCl (0.9%), reaching approximately 127.2% after 24 h and 105.4% after 48 h compared to the control group (100%). Further research in this area will focus on the microfluidic culture of the chosen cancer cell line (H69AR) and the development of novel drug delivery strategies towards appropriate in vivo models for chemotherapy and polychemotherapy treatment.

Deep-penetration functionalized cuttlefish ink nanoparticles for combating wound infections with synergetic photothermal-immunologic therapy.

The challenge of wound infections post-surgery and open trauma caused by multidrug-resistant bacteria poses a constant threat to clinical treatment. As a promising antimicrobial treatment, photothermal therapy can effectively resolve the problem of drug resistance in conventional antibiotic antimicrobial therapy. Here, we report a deep-penetration functionalized cuttlefish ink nanoparticle (CINP) for photothermal and immunological therapy of wound infections. CINP is decorated with zwitterionic polymer (ZP, namely sulfobetaine methacrylate-methacrylate copolymer) to form CINP@ZP nanoparticles. Natural CINP is found to not only exhibit photothermal destruction of methicillin-resistant Staphylococcus aureus (MRSA) and Escherichia coli (E. coli), but also trigger macrophages-related innate immunity and enhance their antibacterial functions. The ZP coating on the surface of CINP enables nanoparticles to penetrate into deeply infected wound environment. In addition, CINP@ZP is further integrated into the thermosensitive Pluronic F127 gel (CINP@ZP-F127). After in situ spraying gel, CINP@ZP-F127 is also documented notable antibacterial effects in mice wound models infected with MRSA and E. coli. Collectively, this approach combining of photothermal therapy with immunotherapy can promote delivery efficiency of nanoparticles to the deep foci of infective wounds, and effectively eliminate wound infections.